LG L192WS User's Manual
Contents
1. 37 500 75 5 800 x 600 37 879 60 6 800 x 600 46 875 15 7 832 x 624 49 725 75 8 1024 x 768 48 363 60 9 1024 x 768 60 123 75 10 1152 x 870 68 681 75 11 1152 x 900 61 805 65 12 1280 x 1024 63 981 60 13 1280 x 1024 79 976 75 14 1440 x 900 55 469 60 15 1440 x 900 55 935 60 16 1440 x 900 70 635 75 Recommend Mode Indicator MODE LED Color On Mode Green Sleep Mode Amber Off Mode Off Installing the Wall mount plate This monitor satisfies the specifications of the Wall mount plate or the interchange device 1 Put a cushion or soft cloth on a flat surface 2 Place the monitor face down on the cushion or soft cloth The Head part The Stand base part 4 Change your hold on the product as it follows and turn the Stand Base in the arrow direction until you hear a click Installing the Wall mount plate 6 Installing the wall mount plate Wall mount plate Separate purchase This is stnad type or will mount type and is connectable with Wall mount plate Please refer to the installation guide for more details which is provided when Wall mount plate is purchased Kensington Security Slot Connected to a locking cable that can be purchased separately at most computer stores Digitally yours aus La2. SA DDC monitor found message Display Sync Input Video Input Resolution Plug amp Play Power Consumption Dimensions amp Weight Tilt Range Power Input Environmental Conditions Stand Base Power cord NOTE 19 48 cm Flat Panel Active matrix TFT LCD Anti Glare coating 19 inches viewable 0 2835 mm pixel pitch 30 83 kHz Automatic 56 75 Hz Automatic Horizontal Freq Vertical Freq Input Form Separate TTL SOG Sync On Green Signal Input 15 pin D Sub Connector Input Form RGB Analog 0 7 Vp p 75 ohm Max VESA 1440 x 900 75 Hz Recommend VESA 1440 x 900 60 Hz DDC 2B On Mode 34 W Typical Sleep Mode lt 1W Off Mode lt 1W With Stand Without Stand Width 43 48 cm 17 11 inches 43 48 cm 17 11 inches Height 37 0cm 14 56 inches 28 73 cm 11 31 inches Depth 18 0cm 7 09 inches 5 87 cm 2 31 inches Net 4 16 kg 9 17 Ibs Tilt 5 20 AC 100 240V 50 60Hz 0 8A Operating Conditions Temperature 10 C to 35 C Humidity 10 to 80 non Condensing Storage Conditions Temperature 20 C to 60 C Humidity 10 to 90 non Condensing Attached _ Detached O Wall outlet type or PC outlet type a Information in this document is subject to change without notice Preset Modes Resolution Display Modes Resolution Horizontal Freq kHz Vertical Freq Hz 1 640 x 350 31 469 70 2 720 x 400 31 468 70 3 640 x 480 31 469 60 4 640 x 480
3. TICAL screen TRACKING CLOCK To improve the clarity and PHASE stability sharpness of the sues fo LANGUAGE To customize the screen OSD status for a user s operating POSITION VERTICAL environment WHITE BALANCE POWER INDICATOR 4 3 IN WIDE FACTORY RESET Adjustable NOTE a The order of icons may differ depending on the model A11 A15 SETUP On Screen Display OSD Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using the OSD system Listed below are the icons icon names and icon descriptions of the all items shown on the Menu Press the MENU Button then the main menu of the OSD appears Menu Name PICTURE CONTRAST E E Icons Ome 50 GAMMA y Ome 0 MENUS vwiel alb SET Button Tip MENU 6 Exit y A Adjust Decrease Increase s SET Enter Select another sub menu NOTE OSD On Screen Display menu languages on the monitor may differ from the manual Main menu D rcr PICTURE Sub menu CONTRAST 9 1H 50 GAMMA 7 Omm 0 GAMMA MENUS wie al gt SET MENU Exit Y Decrease A Increase SET Select another sub menu PRESET COLOR PRESET a a a sRGB 6500K 9300K RED oma J 50 GREEN 1G 50 BLUE fe RED 50 MENUS wiel Aly SET le GREEN a MENU Exit BLUE Y Decrease A Increase SET Sel
4. UAGE SETUP OSD POSITION WHITE HORIZONTAL BALANCE sc ___ aes 3 11 Foo o 50 MENUS vie Aly SETI SETUP WHITE BALANCE LA Ke ro INDICATOR VANUA AK Wend 8 nS MENU Exit Y Adjust 4 3 IN WIDE m A Adjust SET Select another sub menu FACTORY RESET On Screen Display OSD Selection and Adjustment Description To choose the language in which the control names are displayed To adjust position of the OSD window on the screen If the output of the video card is different the required specifications the color level may deteriorate due to video signal distortion Using this function the signal level is adjusted to fit into the standard output level of the video card in order to provide the optimal image Activate this function when white and black colors are present in the screen Use this function to set the power indicator on the front side of the monitor to ON or OFF If you set OFF it will go off If you set ON at any time the power indicator will automatically be turned on To select the image size of the screen 4 3 Depending on the input video signal ratio it is automatically changed to an optimized screen ratio The 1280X1024 input signal is changed to 5 4 ratio and 1024X768 to 4 3 1280x1024 5 4 1152x864 4 1024x768 800x600 640x480 720x480 3 The input signal which the 4 3 IN WIDE does not support 4 3 is the following The 19 inch monitor is 720x400 1280
5. User s Guide L192WS LCD Computer Monitor Make sure to read the Important Precautions before using this product Keep the User s Guide CD in an accessible place for furture reference Have the model and serial number ready when calling for support Important Precautions This unit has been engineered and manufactured to ensure your personal safety however improper use may result in potential electrical shock or fire hazards In order to allow the proper operation of all safeguards incorporated in this display observe the following basic rules for its installation use and servicing On Safety Use only the power cord supplied with the unit In case you use another power cord make sure that it is certified by the applicable national standards if not being provided by the supplier If the power cable is faulty in any way please contact the manufacturer or the nearest authonzed repair service provider for a replacement The power supply cord is used as the main disconnection device Ensure that the socket outlet is easily accessible after installation Operate the display only from a power source indicated in the specifications of this manual or listed on the display If you are not sure what type of power supply you have in your home consult with your dealer Overloaded AC outlets and extension cords are dangerous So are frayed power cords and broken plugs They may result in a shock or fire hazard Call your service
6. ect another sub menu CONTRAST On Screen Display OSD Selection and Adjustment Description BRIGHTNESS Adjusts the brightness of the screen Adjusts the contrast of the screen Set your own gamma value 50 0 50 On the monitor high gamma values display whitish images and low gamma values display high contrast images Selects the color temperature e SRGB Set the screen color to fit the SRGB standard color specification e 6500K Slightly reddish white e 9300K Slightly bluish white Adjusts red color levels Adjusts green color levels Adjusts blue color levels Main menu roson Sub menu On Screen Display OSD Selection and Adjustment Description O HORIZONTAL Adjusts the screen image left and right VERTICAL B 0m J 50 vi ab SETH MENU Exit Y Decrease A Increase SET Select another sub menu TRACKING TRACKING CLOCK PHASE Ome 1 50 SHARPNESS PH AS E A 5 S wie all SETH MENU Exit VERTICAL Adjusts the screen image up and down Adjusts any vertical bars or stripes visible on the screen background The horizontal screen size will also change Adjusts the focus of the display This item allows you to remove any horizontal noise and clear or sharpen text Y Decrease SHARPNESS Adjust the clearness of the screen A Increase SET Select another sub menu Main menu Sub menu LANG
7. ep Mode Energy Saving this indicator color changes to amber On Screen Display OSD Control Adjustment Screen Adjustment Making adjustments to the image size position and operating parameters of the display is quick and easy with the On Screen Display Control system A short example is given below to familiarize you with the use of the controls The following section is an outline of the available adjustments and selections you can make using the OSD NOTE a Allow the display to stabilize for at least 30 minutes before making image adjustments To make adjustments in the On Screen Display follow these steps MENU A V AUTO SET AVY MENU 2 3 Al D Press the MENU Button then the main menu of the OSD appears To access a control use the 4 or Y Buttons When the icon you want becomes highlighted press the AUTO SET Button Use the a w Buttons to adjust the item to the desired level Accept the changes by pressing the MENU Button Exit the OSD by Pressing the MENU Button On Screen Display OSD Selection and Adjustment The following table describes all the On Screen Display control adjustment and setting menus Mainmenu Sabine PICTURE BRIGHTNESS D To adjust the brightness CONTRAST contrast and gamma of the GAMMA screen COLOR PRESET sRGB To customize the color of the eso fo sereen GREEN BLUE POSITION HORIZONTAL To adjust the position of the VER
8. he Head part The Stand base part 4 Change your hold on the product as it follows and turn the Stand Base in the arrow direction until you hear a click 5 e Pull out the Stand to remove Connecting the Display To remove the Stand Base 1 Separate the Stand Body by lifting it as pressing the arrow on the Stand Body while holding q the Stand Base with the other hand 2 The body of the Stand and the Stand Base are successfully separated Connecting the Display Before setting up the monitor ensure that the power to the monitor the computer system and other attached devices is turned off Positioning your display 1 Adjust the position of the panel in various ways for maximum comfort Tilt Range 5 20 Warning When adjusting the angle of the screen do not put your finger s in between the head of the monitor and the stand body You can hurt your finger s Ergonomic It is recommended that in order to maintain an ergonomic and comfortable viewing position the forward tilt angle of the monitor should not exceed 5 degrees Connecting the Display Using the Computer 1 Place the monitor in a convenient well ventilated location near your computer 2 Connect the signal cable When attached tighten the thumbscrews to secure the connection 3 Connect the power cord into a proper power outlet that is easily accessible and close to the display Power Cord Signal Cab
9. he frequency or the resolution were changed If yes readjust the video card to the recommend resolution a Reasons for Recommending Optimal Resolution The aspect ratio is 16 10 If the input resolution is not 16 10 for instance 16 9 5 4 4 3 you might encounter problems such as blurred letters blurry screen cut off screen display or tilted screen a The setting method can differ by computer and O S Operation System and resolution mentioned above may not be supported by the video card performance In this case please ask to the computer or the video card manufacturer Troubleshooting Display image is incorrect The screen color is e Check if the signal cable is properly connected mono or abnormal and use a screwdriver to fasten if necessary e Make sure the video card is properly inserted in the slot e Set the color setting higher than 24 bits true color at Control Panel Settings The screen blinks e Check if the screen is set to interlace mode and if yes change it to the recommend resolution Have you installed the display driver Have you installed the e Be sure to install the display driver from the display display driver driver CD or diskette that comes with your display Or you can also download the driver from our web site http Avww ige com Do you see an e Make sure to check if the video card supports Unrecognized monitor Plug amp Play function Plug amp Play VE
10. le Varies according to model NOTE Wall outlet type a This is a simplified representation of the rear view a This rear view represents a general model your display may differ from the view as shown 3 X PC en LL Ilil PC outlet type po lt n tie Wide Mac adapter For Apple Macintosh use a separate plug adapter is needed to change the 15 pin high density 3 row D sub VGA connector on the supplied cable to a 15 pin 2 row connector 4 Press l button on the rear switch panel to tum the power on KE TRE When monitor power is tumed on the Self Image Setting IMAGE SETTING Function is executed automatically NOTE Self Image Setting Function This function provides the user with optimal display settings When the user connects the monitor for the first time this function automatically adjusts the display to optimal settings for individual input signals AUTO SET Function When you encounter problems such as blurry screen blurred letters screen flicker or tilted screen while using the device or after changing screen resolution press the AUTO SET function button to improve resolution Control Panel Functions Front Panel Controls Rear Lithtview AUTO SET Control Function 1 MENU Button Use this button to enter or exit the On Screen Display OSD LOCKED UNLOCKED This function allows you to lock the current control OSD LOCKED settings so
11. ock On Repacking Do not throw away the carton and packing matenals They make an ideal container in which to transport the unit When shipping the unit to another location repack it in its original maternal On Disposal The fluorescent lamp used in this product contains a small amount of mercury Do not dispose of this product with general household waste Disposal of this product must be camed out in accordance to the regulations of your local authontty Connecting the Display Before setting up the monitor ensure that the power to the monitor the computer system and other attached devices is turned off Connecting the stand 1 Place the monitor with its front facing downward on a soft cloth 2 Assemble the Stand Body into the product in the correct direction as shown in the picture Make sure you push it until you hear it click Stand Body 3 Assemble the Stand Base Front Rear into the Stand Body in the correct direction Stand Base Stand Body N 4 Once assembled take the monitor up carefully and face the front side Important Do not remove and re install the stand frequently it could damage the stand Do not carry the product upside down holding only the stand base The product may fall and get damaged or injure your foot Connecting the Display To remove the Stand 1 Put a cushion or soft cloth on a flat surface 2 Place the monitor face down on the cushion or soft cloth T
12. ou can secure the current control settings LOCKED when you so that they cannot be inadvertently changed push MENU button You can unlock the OSD controls at any time by pushing the MENU button for several seconds the message OSD UNLOCKED will appear Troubleshooting Display image is incorrect Display Position is e Press the AUTO SET button to automatically incorrect adjust your display image to the ideal setting If the results are unsatisfactory adjust the image position using the H position and V position icon in the on screen display On the screen Press the AUTO SET button to automatically background vertical adjust your display image to the ideal setting bars or stripes are If the results are unsatisfactory decrease the visible vertical bars or stripes using the CLOCK icon in the on screen display Any horizontal noise e Press the AUTO SET button to automatically appearing in any adjust your display image to the ideal setting image or characters If the results are unsatisfactory decrease the are not clearly horizontal bars using the PHASE icon in the on portrayed screen display e Check Control Panel gt Display gt Settings and adjust the display to the recommended resolution or adjust the display image to the ideal setting Set the color setting higher than 24 bits true color Important a Check Control Panel gt Display gt Settings and see if t
13. tchen sink laundry tub in a wet basement or near a swimming pool Displays are provided with ventilation openings in the cabinet to allow the release of heat generated during operation If these openings are blocked built up heat can cause failures which may result in a fire hazard Therefore NEVER Block the bottom ventilation slots by placing the display on a bed sofa rug etc Place the display in a built in enclosure unless proper ventilation is provided Cover the openings with cloth or other maternal Place the display near or over a radiator or heat source Do not rub or strike the Active M atrix LCD with anything hard as this may scratch mar or damage the Active M atrix LCD permanently Do not press the LCD screen with your finger for a long time as this may cause some afterimages Some dot defects may aopear as Red Green or Blue spots on the screen However this will have no impact or effect on the display performance If possible use the recommended resolution to obtain the best image quality for your LCD display If used under any mode except the recommended resolution some scaled or processed images may appear on the screen However this is charactenstic of the fixed resolution LCD panel On Cleaning Unplug the display before cleaning the face of the display screen Use a slightly damp not wet cloth Do not use an aerosol directly on the display screen because over spraying may cause electrical sh
14. technician for replacement Do not Open the Display There are no user serviceable components inside a There are Dangerous High Voltages inside even when the power Is OFF Contact your dealer if the display is not operating propery To Avoid Personal Injury Do not place the display on a sloping shelf unless propery secured Use only a stand recommended by the manufacturer a Do not drop an object on or apply impact to the product Do not throw any toys or objects on the product screen It can cause injury to human problem to product and damage the display To Prevent Fire or Hazards Always tum the display OFF if you leave the room for more than a short pernod of time Never leave the display ON when leaving the house Keep children from dropping or pushing objects into the display s cabinet openings Some intemal parts carry hazardous voltages a Do not add accessones that have not been designed for this display When the display is to be left unattended for an extended period of time unplug it from the wall outlet a Inthe presence of thunder and lightning never touch the power cord and signal cable because it can be very dangerous It can cause electric shock Important Precautions On Installation Do not allow anything to rest upon or roll over the power cord and do not place the display where the power cord is subject to damage Do not use this display near water such as near a bathtub washbowl ki
15. that they cannot be inadvertently changed Press and hold the MENU button for several seconds EE The message OSD LOCKED should appear You can unlock the OSD controls at any time by pushing the MENU button for several seconds The message OSD UNLOCKED should appear Use these buttons to select or adjust functions in the On 2 AY Buttons Screen Display LightView hot key pay This feature lets you easily select the best desired NIGHT Mage condition optimized to the environment DAY TEXT ambient illumination image types etc DAY Bright ambient illumination SESS e NIGHT Dark ambient illumination e TEXT For text images Word processing etc e MOVIE For animation images in videos or movies e PHOTO For pictures or drawings e NORMAL This is under normal operating conditions Control Panel Functions Control Function AUTO SET Use this button to enter a selection in the On Screen Button Display AUTO IMAGE ADJUSTMENT When adjusting your display settings always press the AUTO SET button before entering the On Screen Display OSD This will automatically adjust your display image to the ideal settings for the current screen resolution size display mode PROCESSING AUTO The best display mode is O L192WS 1440 x 900 O Power Button Use this button to turn the display on or off 5 Power Indicator This Indicator lights up green when the display operates normally On Mode If the display is in Sle
16. x768 1360x768 1440x900 Restore all factory default settings except LANGUAGE Press the Y button to reset immediately If this does not improve the screen image restore the factory default settings lf necessary perform the white balance function again This function will be enabled only when the input signal is an analog signal Troubleshooting Check the following before calling for service No image appears Is the power cord of the Check and see if the power cord is connected display connected properly to the power outlet Is the power indicator Press the Power button light on Is the power on and the Adjust the brightness and the contrast power indicator blue or green Is the power indicator If the display is in power saving mode try moving amber the mouse or pressing any key on the keyboard to bring up the screen e Try to turn on the PC Do you see an OUT OF This message appears when the signal from the RANGE message on PC video card is out of horizontal or vertical the screen frequency range of the display See the Specifications section of this manual and configure your display again Do you see a CHECK This message appears when the signal cable SIGNAL CABLE between your PC and your display is not message on the connected Check the signal cable and try again screen Do you see a OSD LOCKED message on the screen Do you see OSD e Y
Download Pdf Manuals
Related Search