Home

Lexicon SDP-40 User's Manual

1. 10 20 50 100 200 500 1k 2k 5k 10k 20k Hz 40 The AUDIO CONTROLS Menu TREBLE AUDIO CONTROLS e TREBLE controls the amount of boost or cut applied to the FRONT L R and CENTER outputs When TREBLE is selected a horizontal graph will appear on the screen below the parameter This graph illustrates the position at which the current setting falls within the 6 0 to 6 0dB parameter range Press the up and down MENU arrows to increase and decrease the setting in 0 5dB increments Press the left MENU arrow to close the graph and return to the AUDIO CONTROLS menu 6 0 to 6 0dB The graph pictured below shows the frequency response of all TREBLE settings 6 0 455 45 0 45 40 435 43 0 425 42 0 415 10 0 5 40 0 0 5 10 AS 2 0 25 30 35 40 45 50 45 6 0 10 20 50 100 200 500 1k 2k 5k Hz 10k 20k TILT EQ AUDIO 15 6 TILT EQ controls the amount of tilt equalization applied to the FRONT L R CENTER SUBWOOFER L R and LFE outputs When TILT EQ is selected a horizontal graph will appear on the screen below the parameter This graph illustrates the position at which the current setting falls within the 3 0 to 3 0dB parameter range Press the up and down MENU arrows to increase and decrease the setting in 0 5dB increments Press the left MENU arrow to close the graph and return to the AUDIO CON
2. 3 29 Menu Navigation 1 4 to 1 5 REC Button vu sare ex a E Ro RR 2 8 LIMITER 3 29 Menu Tree culata acia cen c c A 5 to A 11 REC PWR ON yucatan da Rhe hh 3 34 ree erecta 8 So Me ene rtp See also LOGIC7 MICROPHONE INPUTS 2 6 RECORD ea AA da 3 17 L7 Button eR 2 14 2 16 to 2 17 Mode ilv vex see also Listening Mode RECORD ADVANCED 3 16 to 3 17 LD B tton rr eI v ESSET 2 3 2 9 a m e ese es 5 23 RECORD AUDIO OUTPUTS 2 5 LEDs Front Panel 2 2 Illustration 2 3 MODE Buttons 2 11 2 16 to 2 17 RECORD BALANCE 2 12 2 13 4 5 Level Meters STATUS Menus 5 18 MODE ADJUST 5 2 Record Input Selection Buttons 2 3 LEVELS CALIBRATION Menu 3 26 to 3 29 MODE ADJUST Menu 5 1 to 5 24 Record Off Button 2 3 ed onis 3 23 3 24 5 17 5 22 Mode Family Selection Buttons 2 14 2 16 to 2 17 RECORD VIDEO OUTPUTS 2 5 Index SDP 40 REF OFFSET 5 4 4 seedy ee 5 23 Remote 2 7 to 2 14 REMOTE Operation Triggers 3 35 REMOTE STATE 3 32 Removable Access Panel 2 6 RESET MODE 5 17 RESTORE DEFAULT NAME
3. DVD1 is used as an example in this illustration and will continue to be used as an example throughout this section Whenever DVD1 appears as a step in a menu path any other input may be substituted INPUT SELECT AUTO ANALOG DIGITAL DIGITAL IN connector is utilized when a valid digital audio The INPUT SETUP menu allows the selection of two audio input type is present When invalid digital audio input connector types one analog one digital INPUT SELECT specifies types are received the unit automatically switches to the how these connectors interact The following settings are available ANALOG IN connector INPUT SELECT will automatically be set to AUTO when a connect or selected for both the DIGITAL IN and ANALOG IN parameters This setting is e DIGITAL setting forces the unit to utilize the DIGITAL recommended for input sources that utilize both digital IN connector for Zone 2 If an ANALOG IN connector is and analog audio input types such as a laser disc player also selected it will be ignored The unit will mute when an invalid digital audio input type is received Valid digital audio input types include PCM Dolby Digital and Note dts ES See 2 1 6 for more information about using Some sources supply valid digital audio input types the DIGITAL setting in multiple zones that remain active even when no audio is present in the signal Because the unit recognizes these as valid e
4. xi JBL Section 1 Getting Started OVERVIEW ERRARE MUR REL VER 1 2 Highlights 2 a 1 3 Using the Documentation 1 4 Location Considerations 1 4 Navigating the 1 4 Two Line Status viii idas cea maed dci 1 5 Restoring Factory Default Settings 1 5 Section 2 Basic Operation Front Panel d REG eiua 2 2 Rear Panel osse ac ed bras ve RU AA 2 4 Remote Control he ehe d 2 7 Understanding the Zones 2 15 Understanding Listening Mode Selection 2 16 Section 3 The SETUP Menu SETUP ani eo accedo Oa wind UR ea Ut on 3 2 INPUT SETUP eh hb rure Re 3 3 SPEAKER SETUP 5 t nee e iore xe 3 18 REAR PANEL CONFIG 3 30 DISPLAY SETUP id ec da sat 3 31 VOLUME CONTROL SETUP 3 34 TRIGGER SETUP oo cert rep tec aia 3 35 LOCK OPTIONS eerie ie seein ene ale bU Ve RR 3 36 40 Introduction Section 4 The AUDIO CONTROLS Menu AUDIO CONTROLS 4 2 Section 5 The MODE ADJUST Menu ADJUST 13 uud aci ii a A Rob 5 2 Listening Mode Descriptions 5 2 OUTPUT LEVEE
5. Default Parameter Value Values CENTER 0dB OFF 30 to 12dB SIDE L R 0dB OFF 30 to 12dB REAR L R 0dB OFF 30 to 12dB SUB L R 0dB OFF 30 to 12dB LFE 0dB OFF 30 to 12dB The LFE parameter is only available for 5 1 channel listening modes An alphabetical listing of parameter descriptions begins on page 5 20 When a SYNTHESIS 7CH SETUP is selected the LFE parameter will appear on the OUTPUT LEVELS menu for the 5 1 THX SURROUND EX or 5 1 THX and dts ES THX listening modes This parameter only has an effect when the LFE parameter on the CUSTOM SETUP menu is set to ON page 3 23 CUSTOM MODE ADJUST gt LISTENING MODE gt CUSTOM The CUSTOM menu be used to cusroM compare modified listening mode versions to their original factory default versions CUSTOM VS PRESET RESET MODE CUSTOM VS PRESET CUSTOM VS PRESET allows comparison custom listening of the modified and factory default versions of the selected listening mode This option is available even when modifications have been made to the selected listening mode But the custom and preset versions of the listening mode will sound the same until modifications are made Selecting CUSTOM VS PRESET accesses the pulldown menu pictured at the right Pressing the up and down MENU arrows toggles between the modified and factory default versions of the selected listening mode The message CUS
6. THX SURRROLLOFF 15 3kHz LFE MIX 0 0dB DO PRO LOGIC REARDLYOFFSET 15ms 1 LEVELS MONO SURROUND OUTPUT LEVELS SURRROLLOFF 3 1kHz PL Il MUSIC OUTPUT LEVELS OUEN CUSTOM OUTPUT LEVELS DO PRO LOGIC CUSTOM CUSTOM GUSTOM 2 CHANNEL OO PL MUSIC PARTY ZW 2A EE SUR EA 5 1 MONO SURR MONO E RE EQUALIZER ON MONO LOGIC CTR WIDTH 3 OUTPUT LEVELS MONO SURROUND AJTO AZIMUTE ON DIMENSION NEUTRAL VOCALENHANCE 0 0gB SURROUND EX ON cystom VOCAL ENHANCE 0 00 COMPRESSION OFF 5 1 191 FILM SURROUND DLY 5ms 5SPKRENHANCE OFF si FRONT STEERING MUSIC LFE MIX 40 0dB 5 1 lo TV OUTPUT LEVELS BASS ENHANCE OFF 1 RE EQUALIZER OFF custom OUTPUT LEVELS HAES 5 FILM 5 1 15 MUSIC RE EQUALIZER ON SOUND STAGE REAR CUSTOM 5 1 THX SUR EX REAR DLY OFFSET 15ms DIGITAL MR OFF COMPRESSION OFF VOCAL ENHANCE 0 008 BASS ENHANCE OFF PRO LOGIC LEE MIX 0 008 5 SPKR ENHANCE OFF I A OHANNEL SURRROLLOFF 15 3kHz 2 4 DO DIGITAL BASS ENHANCE OFF oa REAR DLY OFFSET t5ms OUTPUT LEVELS ol RE EQUALIZER ON 7 0 OUTPUT LEVELS CUSTOM COMPRESSION REARDLYOFFSET 15m zs 15 FILM CUSTOM LFE MIX 0 0dB LFE MIX 0 00B Es 127 MUSIC 2 CHANNEL 5 1 iTV ciel LEVELS OUTPUT LEVELS E THX 1 MUSIC CUSTOM SUB L R LVL 40dB VOCAL ENHANCE 0 00 TAS 2 CHAN VOCAL ENHANCE 0 0dB CUSTOM 5SPKR ENHANCE OFF 51 2 CHANNEL Eras 151 MUSIC 5 1 BYPASS FRONT STEERING MUSIC BASS ENHANCE OFF 2 BYPASS SOUND STAGE NEUTRAL party RE
7. 5 2 to 5 16 MONO SURROUND 5 8 FORMAT ER ad Rodan deste 3 32 Listening Mode Selection 2 16 to 2 17 MUSIC Button 2 14 2 16 to 2 17 EP B tton iii 2 10 Listening Mode STATUS Menus 5 18 to 5 20 MUTE Button 2 3 2 12 Frequency Response Curves 3 19 Illustration Location 1 4 MUTE LEVEL em Ere 3 34 1 3 20 3 24 LOCK OPTIONS 3 2 NAME aa ao 3 4 Front Panel 2 2 Illustration to 2 3 LOCK OPTIONS Menu 3 36 Navigating the Menus 1 4 to 1 5 Front Panel Display 2 2 Illustration 2 3 LOGIC7 2 17 5 2 ON SCREEN DISPLAY Menu 3 31 to 3 32 FRONT PANEL DISPLAY Menu 3 32 to 3 33 LOGIC7 MUSIC 2 17 5 3 OSD Button posses eee EE 2 10 FRONT STEERING 5 22 EOGICZ tes 2 17 5 3 OUTPUT LEVELS Menu 5 17 GAME Button 2 3 2 9 LOUDNESS 2 9 4 4 OUTPUTS oi cee hen 2 4 to 2 6 Help ea 6 2 to 6 3 Lowpass Filter 3 19 Illustration PANORAMA EE e 5 23 Highpass Filtrer 3 19 Illustration MAIN ADVANCED 3 12 to 3 14 PARTY LA a
8. viii 40 Introduction DANSK VIGTIG INFORMATION OM SIKKERHED Gem denne vejledning til senere brug Felg alle anvisninger og advarsler p apparatet e Apparatet skal altid tilsluttes den korrekte sp nding Der henvises til brugsanvisningen der indeholder specifikationer for str mforsyning Der g res opm rksom p at ved varierende driftssp ndinger kan det blive n dvendigt at bruge andre lednings og eller stiktyper e Apparatet m ikke monteres i et kabinet uden ventilation eller lige over andet udstyr der udvikler varme f eks forst rkere Den maksimale omgivelsestemperatur ved drift der st r opf rt i specifikationerne skal overholdes Der er ventilations bninger i kabinettet For at sikre apparatets drift og hindre overophedning m disse bninger ikke blokeres eller tild kkes Stik aldrig noget ind igennem ventilations bningerne og pas p aldrig at spilde nogen form for v ske p apparatet e Dette apparat er forsynet med et stik med jordforbindelse Denne sikkerhedsforanstaltning m aldrig omg s e Udgangsstik fra audioforst rkere m aldrig s ttes direkte i apparatet e Apparatet m ikke uds ttes for regn eller fugt og m ikke bruges i n rheden af vand for at undg risiko for elektrisk st d og brand e Apparatet m aldrig bruges hvis det er blevet st dt beskadiget eller v dt eller hvis ndringer i ydelsen tyder p at det tr nger til eftersyn e Dette a
9. pup eise peat dva eue pope 3 18 REAR PANEL CONFIG RA ARRAY 3 30 DISPLAY SETUP aaa 3 31 VOLUME CONTROL SETUP coc 3 34 TRIGGER SETUP vano See eo p bro ooh eoa AI RARES 3 35 The SETUP Menu JBL SETUP SETUP Selecting SETUP on the MAIN MENU accesses the SETUP menu which contains INPUTS options that access available setup b Use th d down MENU REAR PANEL CONFIG submenus Use the up and down M DISPLAYS arrows to scroll through the complete list of VOLUME CONTROLS options Press the right MENU arrow to TRIGGERS select the highlighted option Press the left LOSICOPTIONS MENU arrow to return to the MAIN MENU INPUTS Selecting INPUTS prompts the selection of the desired input for configuration Selecting a specific input accesses the INPUT SETUP menu which contains options and parameters for configuring the selected input See page 3 3 for more information SPEAKERS Exa Selecting SPEAKERS accesses the SPEAKER SETUP menu which contains options to configure the MAIN AUDIO OUTPUTS See page 3 18 for more information REAR PANEL CONFIG 2 Selecting REAR PANEL CONFIG accesses the REAR PANEL CONFIG menu which contains options that configure the function of analog input pairs 6 7 and 8 on the rear panel See page 3 30 for more information DISPLAYS BE Selecting DISPLAYS accesses the DISPLAY SETUP menu which
10. 2 7 2 8 BASS 2 9 2 10 4 2 BASS ENHANCE 2225 5 GU aa diles 5 21 BLUE B ttOm osa Saas dscns 2 10 BRIGHTNESS ca en mee 3 32 CAL NOISE sed e eR RASA Eee 3 29 CD BUON eo usse ptem 2 3 2 9 CENTER 3 20 3 24 5 17 5 21 CENTER see mhi 5 21 CHANNELS 5 5445 ea Eni 5 21 CNTR DLY SAMPLES 5 21 Command Bank Selection 2 7 2 8 COMPONENT IN 3 9 COMPONENT OSD 3 14 COMPRESSION 5 21 Connectors 2 4 to 2 6 Crossover Settings Determining 3 18 CUR WIDTH ii cea nm m 5 22 CUSTOM 5 17 CUSTOM NAME 3 33 CUSTOM SETUP Menu 3 18 to 3 23 CUSTOM VS PRESET 5 17 DACS CALIBRATION 3 27 to 3 28 Declaration of Conformity A 4 DIG OUT RATE 3 17 DIGITAL BYPASS 3 17 DIGITALIN ska RPG Rete 3 5 DIMENSION 54 54 rr se aie eee gee 5 22 Display Front Panel 2 2 illustration 2 3 DISPLAY SETUP Menu 3 31 to 3 33 DISPLAYS aii apra ORE RR 3 2 Documentation About the 1 4 DOLBY Button 2 14 2 16 to 2 17 DOLBY D ira 2 16 3 10 to 3 11 DOLBY DIGITAL 2 17 5 11 DOLBY DIGITAL STATUS
11. ANALOG setting forces the unit to utilize the selected digital audio input types it will not switch to the ANALOG connector for Zone 2 If a DIGITAL IN ANALOG IN connector For these sources it is recommended to configure two different inputs one for digital audio input types and a second for analog audio input types connector is also selected it will be ignored e AUTO setting allows the unit to switch between the selected DIGITAL IN and ANALOG IN connectors The 3 15 The SETUP Menu JBL MAIN MENU gt SETUP gt INPUT SETUP gt DVD1 INPUT SETUP gt DVD1 RECORD ADV MODE ADJUST NAME DVD1 INPUT SELECT DIGITAL AUDIO CONTROLS SPEAKERS DVD2 DIGITAL IN COAX 1 ANLG IN LVL 0dB REAR PANEL CONFIG LD ANALOG IN NONE DIGITAL BYPASS OFF DISPLAYS TV ANLG IN LVL AUTO DIG OUT RATE 44 1kHz VOLUME CONTROLS SAT VIDEO IN S VIDEO 1 RECORD ENABLED TRIGGERS VCR COMPONENT IN 1 LOCK OPTIONS CD 2 CH L7 FILM PVR DO D 5 1 L7 FILM GAME TAES dts L7 FILM TAPE MAIN ADVANCED TUNER ZONE2 ADVANCED AUX DVD1 is used as an example in this illustration and will continue to be used as an example throughout this section Whenever DVD1 appears as a step in a menu path any other input may be substituted RECORD ADVANCED INPUT SELECT AUTO ANALOG DIGITAL EU e DOI Selecting RECORD ADVANCED accesses the RECORD AD
12. INPUT SELECT AUTO ANALOG DIGITAL The INPUT SETUP menu allows the selection of two audio connector types one analog one digital INPUT SELECT specifies how these connectors interact The following settings are available e The DIGITAL setting forces the unit to utilize the DIGITAL IN connector for the Main Zone If an ANALOG IN connector is also selected it will be ignored The unit will mute when an invalid digital audio input type is received Valid digital audio input types include PCM Dolby Digital and dts ES The DIGITAL setting will automatically be selected when the ANALOG IN parameter on the INPUT SETUP menu is set to NONE see page 3 6 e The ANALOG setting forces the unit to utilize the selected ANALOG IN connector for the Main Zone If a DIGITAL IN connector is also selected it will be ignored The ANALOG setting will automatically be selected when the DIGITAL IN parameter on the INPUT SETUP menu is set to NONE see page 3 5 e AUTO setting allows the unit to switch between the selected DIGITAL IN and ANALOG IN connectors The DIGITAL IN connector is utilized when a valid digital audio input type is present When invalid digital audio input types are received the unit automatically switches to the ANALOG IN connector INPUT SELECT will automatically be set to AUTO when a connect or selected for both the DIGITAL IN and ANALOG IN parameters This setting is recommended for input sources that utilize both di
13. 5 24 SYNTHESIS 7CH SETUP Menu 3 24 to 3 25 Table of Contents iv to v TAPE BUOM onm ye Fere dd 2 3 2 9 THX Button 2 14 2 16 to 2 17 TIET EQ 2 2 0d or is t tent 2 9 2 10 4 3 TREBLE a es Sis chistes tetas teasers Las red 2 9 2 10 4 3 TRIGGER T ep RUE 2 11 3 35 TRIGGER 2 ei ev ENS 2 11 3 35 TRIGGER OUTPUTS 2 6 TRIGGER SETUP Menu 3 35 TRIGGERS 3 2 Troubleshooting 6 2 to 6 3 TUNER Button 2 3 2 9 TV Button 2 3 2 9 TVL Button 2 14 2 16 to 2 17 Two Line Status 1 5 2 12 Unbalanced Audio Outputs 2 5 Unpacking and Inspection Instructions xi User Guide About the 1 4 VCR Button 2 3 2 9 VIDEO UND Ses a cae i oen te ee Rc 3 8 VIDEO INPUTS odian 2 5 VOCAL ENHANCE 5 24 VOL Buttons 2 11 VOLUME CONTROL SETUP Menu 3 34 VOLUME 1 3 2 Volume Knob 2 3 Warranty Inside Back Cover ZONE Button 2 8 ZONE 3 34 ZONE2 ADVANCED 3 14 to 3 15 ZONE2 BALANCE 2 12 2 13 4 4 ZONE 2 AUDIO OUTPUTS 2 5 Zone 2 Input Selection But
14. future expansion Reserved for future expansion See page 5 24 for more information about the SURROUND EX parameter See page 2 18 for more information about mode selection using Mode Family Selection Buttons 40 Basic Operation UNDERSTANDING THE ZONES The SDP 40 features three zones the Main Zone Zone 2 and the Record Zone The Main Zone is designed to control audio and video signals in the primary listening space Zone 2 is designed to control audio signals in the secondary listening space and the Record Zone is designed to control audio and video signals for recording devices The Record Zone can also function as a third zone controlling audio and video signals in a third listening space All three zones utilitize separate digital audio receivers analog to digital converters and digital to analog converters This allows independent input selection in each zone with most input types For instance the unit can play a DVD in the Main Zone play a CD in Zone 2 and send signals from a satellite receiver to a VCR through the Record Zone all at the same time The following exceptions apply to independent zone function e same Dolby Digital or dts ES input type can be selected in all zones simultaneously However when a Dolby Digital or dts ES input type is active in the Main Zone a different Dolby Digital or dts ES input type cannot be active in Zone 2 or the Record Zone e Z
15. Default Parameter Value Values OUTPUT LEVELS See page 5 17 for more information CUSTOM See page 5 17 for more information An alphabetical listing of parameter descriptions begins on page 5 20 2 CHANNEL BYPASS repr gt 2 55 e Designed for playback of 2 channel analog input sources e When selected the input signal bypasses internal processing and bypasses to the FRONT L R outputs The 2CH BYPASS listening mode is not available unless and will be automatically selected when all of the following conditions are met e ANALOG IN parameter on the INPUT SETUP menu is set to the connector utilized by the input source see page 3 6 e The INPUT SELECT parameter on the MAIN ADV menu is set to either AUTO or ANALOG see page 3 13 When set to AUTO no digital input types can be present e ANALOG BYPASS parameter on the MAIN ADV menu is set to ON see page 3 13 No parameters are available for the 2CH BYPASS listening mode 5 16 SDP 40 The MODE ADJUST Menu OUTPUT LEVELS gt gt The OUTPUT LEVELS menu contains parameters for adjusting CENTER SIDE L R REAR L R SUBWOOFER L R and LFE output levels on a per mode basis The OUTPUT LEVELS menu is not available for listening modes that do not accommodate multi channel outputs such as MONO For these listening modes the OUTPUT LEVELS menu option appears as an output specific parameter such as CENTER LVL
16. 3 4 Restoring Factory Default Settings 1 5 6 4 RS 232 Connectors 2 6 S PDIF INPUTS 2 5 S VIDEO 169 3 14 S VIDEO OSD 4 3 3 14 Safety Instructions Inside Front Cover vi to xi 1 4 SAMPLE RATE ERR TEC 5 23 SAT 2 3 2 9 SDP 40 About the 1 2 to 1 3 SETUP ct vede eon Ries 3 2 3 36 SETUP Menu 3 1 to 3 36 SHIFT 2 8 SIDE L R RR 3 21 3 24 5 17 5 23 Sound Pressure Level SPL 3 26 SOUND STAGE 5 24 SPEAKER DISTANCES Menu 3 25 SPEAKER LEVEL ADJUST Menu 3 26 SPEAKER SETUP Menu 3 18 to 3 29 SPEAKERS oo err i dial 3 2 Specifications A 2 to A 3 Standby Button 2 2 2 8 STAT BUTON SS DER ups 2 12 STATUS secedere o YE 2 10 3 31 3 32 Status Menu Level Meters 5 18 STATUS Menus 2 12 5 18 to 5 20 SUB L R crac a kev oe 3 22 3 24 5 17 5 24 SUB L R IVL 555 ii REED 5 24 SUB LIMITERS Menu 3 28 to 3 29 SUB XOVER 3 22 3 24 SURRROLLOFF 5 24 SURROUND DIY 5 24 SURROUND EX 2 14 3 25 5 24 SURROUND
17. Basic Operation BANK Scroll through available listening modes in the Main Zone Pressing the Mode button selects the previous listening mode pressing the Mode button selects the next listening mode See page 2 17 for more information about mode selection using the Mode and buttons MODE Activates Trigger 1 when TRIGGER 1 is set to REMOTE in the TRIGGER SETUP menu MODE Deactivates Trigger 1 when TRIGGER 1 is set to REMOTE in the TRIGGER SETUP menu See page 3 35 for more information about the TRIGGER SETUP menu MODE Activates Trigger 2 when TRIGGER 2 is set to REMOTE in the TRIGGER SETUP menu MODE Deactivates Trigger 2 when TRIGGER 2 is set to REMOTE in the TRIGGER SETUP menu See page 3 35 for more information about the TRIGGER SETUP menu MODE Powers the unit on MODE Places the unit into standby Adjusts Main Zone volume in 1dB increments Adjusts Zone 2 volume in 1dB increments Adjusts Record Zone volume in 1dB increments Adjusts Main Zone volume in 3dB increments Basic Operation EN JBL Displays the two Displays the two Displays the two Toggles between line status of the line status of line status of the accessing and STAT Main Zone for Zone 2 for two Record Zone for exiting the two seconds seconds two seconds STATUS menu Togg
18. ERA E 5 6 lt 55 teet eere ree terne 5 22 MAIN AUDIO 5 2 5 POSITION EU 3 31 INPUT SELECT 3 13 3 15 3 16 to 3 17 MAIN Button 2 8 Power Switch Rear Panel 2 5 Input Selection Buttons 2 3 2 9 Main Input Selection Buttons 2 3 PROGRAM Operation Triggers 3 35 INPUT SETUP Menu 2 16 to 2 17 3 3 to 3 17 MAIN MENU 1 4 2 12 PVR Button 2 3 2 9 INPUT TYPE ee seh oleae dd 5 22 Main Off Button 2 3 RESEQUALIZER 2 40 5 23 A Re eei lack ee es 2 4 to 2 6 MAIN PWR ON 3 34 REAR DLY OFFSET 5 23 INPUTS gsc ade be eat 3 2 MAIN VIDEO OUTPUTS 2 5 REARL R 3 21 3 24 to 3 25 5 17 5 23 Installation Worksheet A 12 to A 13 Maintenance 6 4 Rear Panel 2 4 Illustration to 2 6 INTERNAL NOISE TEST 3 26 to 3 27 MASTER LEVEL ein aed 214 5 23 REAR PANEL 3 2 IRIN Connector 2 6 MENU Arrows 2 13 REAR PANEL CONFIG Menu 3 30 IR 2 2 Illustration 2 3 MENU Button 2 12 Rear Panel Power Switch 2 5 LIMIT AD
19. Recommended for 2 channel music sources even when only one pair of surround speakers is selected Default Parameter Value Values AUTO AZIMUTH ON ON OFF VOCAL ENHANCE 0 0dB 0 0 3 0dB 6 0dB FRONT STEERING MUSIC OFF MUSIC FILM RE EQUALIZER OFF ON OFF SOUND STAGE REAR FRONT NEUTRAL REAR 5 SPKR ENHANCE OFF ON OFF BASS ENHANCE OFF ON OFF SURR ROLLOFF 15 3kHz 500Hz to 20 0kHz OFF REAR DLY OFFSET 15ms 0 to 30ms OUTPUT LEVELS See page 5 17 for more information CUSTOM See page 5 17 for more information An alphabetical listing of parameter descriptions begins on page 5 20 Default Parameter Value Values VOCAL ENHANCE 0 0dB 0 0 3 0dB 6 0dB FRONT STEERING MUSIC OFF MUSIC FILM SOUND STAGE NEUTRAL FRONT NEUTRAL REAR 5 SPKR ENHANCE OFF ON OFF BASS ENHANCE OFF ON OFF SURR ROLLOFF 15 3kHz 500Hz to 20 0kHz REAR DLY OFFSET 15ms 0 to 30ms OUTPUT LEVELS See page 5 17 for more information CUSTOM See page 5 17 for more information An alphabetical listing of parameter descriptions begins on page 5 20 5 3 The MODE ADJUST Menu JBL DOLBY PRO LOGIC THX AAA 11 Designed for playback of mm Surround encoded sources e Utilizes Dolby Pro Logic II to decode five channels from Dolby Surround encoded input types e Applies re equalization and timbre matching Re equalization simulates the high frequency rolloff tha
20. l att andra matningssp nningar eventuellt kr ver att en annan typs n tsladd och eller kontakt anv nds e Installera inte enheten i ett oventilerat stativ eller direkt ovanf r utrustningar som avger v rme t ex effektf rst rkare Se till att omgivningens temperatur vid drift inte verskrider det angivna v rdet i produktspecifikationen e Beh llaren r f rsedd med h l och ppningar f r ventilering F r att garantera tillf rlitlig funktion och f rhindra verhettning f r dessa ppningar inte blockeras eller t ckas Inga f rem l far skuffas in genom ventilationsh len Inga v tskor f r spillas p enheten e Produkten r f rsedd med en jordad 3 tr dskontakt Detta r en s kerhetsfunktion som inte f r tas ur bruk e Anslut aldrig audioeffektf rst rkarutg ngar direkt till n gon av enhetens kontakter e F r att undvika elst t eller brandfara f r enheten inte uts ttas f r regn eller fukt eller anv ndas p st llen d r den blir v t e Anv nd inte enheten om den har fallit i golvet skadats blivit vat eller om dess prestanda f r ndrats m rkbart vilket kr ver service Enheten f r ppnas endast av beh rig servicepersonal Farliga sp nningar blir tillg ngliga n r locken tas bort oisolerad farlig sp nning inne i enheten Denna sp nning r eventuellt Denna triangel som visas din komponent varnar dig om s h g att fara for elst t foreligger Denna triangel som visas pa d
21. speakers to the left and right of the primary listening position ACADEMY FILTER ON OFF When set to ON ACADEMY FILTER restores the proper tonal balance of older mono film sources which generally have much narrower frequency responses than current mono film sources AUTO AZIMUTH ON OFF AUTO AZIMUTH maximizes the output accuracy of the listening mode When set to ON the unit continually monitors the 2 channel input signal It automatically adjusts the relative level and time offset of the input channels to ensure that signals are sent to the appropriate channels with maximum separation When set to OFF the accuracy of the listening mode varies depending on the input source This parameter should be set to ON for film and TV sources and OFF for music sources 5 20 40 The MODE ADJUST Menu BASS ENHANCE ON OFF BASS ENHANCE creates stereo bass which results in low frequency reproduction that is less localizable and more realistic in the listening space When set to ON the unit processes the low frequencies sent to the FRONT L R SIDE L R and REAR L R outputs to create stereo low frequencies This also includes the SUBWOOFER L R outputs when the SUB L R parameter on the CUSTOM SETUP menu is set to STEREO The crossover setting of the CENTER parameter on the CUSTOM SETUP menu is critical to the effectiveness of BASS ENHANCE It is recommended to set the CENTER parameter to 120Hz and the SUB L R parameter t
22. 2 CHANNEL 5 11 5 1 ANALOG STATUS Menu 5 19 S BYPASS aod ac RIO Ies 2 15 5 16 5 1 BYPASS STATUS Menu 5 19 5 1 LOGIC7 FILM 2 17 5 8 5 1 LOGIC7 MUSIC 2 17 5 9 5 1 LOGIC7 coe 2 17 5 9 5 1 MONO a 5 12 5 1 MONO LOGIC 5 12 5 1 MONO SURROUND 5 13 A ota poet dara debe Bob 2 17 5 10 5 1 THX SURROUND EX 2 17 5 10 7 5 Button 2 13 8 STEREO INPUTS 3 30 AC Input Connector 2 5 ACADEMY FILTER 5 20 Access Panel 2 6 AES EBU 2 5 ANALOG BYPASS 3 13 to 3 14 ANALOG IN 3 6 ANLG IN LVL 3 6 to 3 7 3 17 ATTOWS 5 2 13 Audio Calibration Disc 3 27 to 3 28 AUDIO CNTRL l l 3 36 AUDIO CONTROLS 4 2 AUDIO CONTROLS Menu 4 1 to 4 5 AUDIO INPUTS 2 5 AUTO AZIMUTH 5 20 AUX Button 2 3 2 9 A V SYNC DELAY 3 32 to 3 33 Back Panel see Rear Panel BACKGROUND 2 10 3 32 BALANCE eee eda 2 12 2 13 4 4 Balanced Audio Outputs 2 5 Bank Selection Buttons
23. DLY OFFSET 15ms 0 to 30ms LFE MIX 0 0dB 10 0 to 0 0dB OUTPUT LEVELS See page 5 17 for more information CUSTOM See page 5 17 for more information An alphabetical listing of parameter descriptions begins on page 5 20 dts ES THX LIE o Emm Designed for playback of 5 1 and 6 1 channel dts ES encoded sources e Utilizes dts ES to decode 5 1 or 6 1 discrete channels from dts ES encoded input types e Applies re equalization and timbre matching Re equalization simulates the high frequency rolloff that occurs in a movie theater as sound travels from the speakers to the listeners Most films are mixed for movie theaters and may sound too bright when played back in a home theater without re equalization Timbre matching helps minimize the timbre differences between the front and side channels which results in smoother sound movements between these channels Recommended for home theaters with a THX certified speaker system e The unit will automatically activate ES decoding when dts ES input type is identified Default Parameter Value Values RE EQUALIZER ON ON OFF LFE MIX 0 0dB 10 0 to 0 0dB OUTPUT LEVELS See page 5 17 for more information CUSTOM See page 5 17 for more information An alphabetical listing of parameter descriptions begins on page 5 20 5 14 SDP 40 The MODE ADJUST Menu dts and dts ES MODE ADJUST 9 EZ dts dts The unit will automatically switch betwee
24. DOLBY DIGITAL listening mode And if a dts ES input type is coming in the unit will acti vate the dts ES listening mode When DACS CALIBRATION is selected these listening modes will retain their factory default settings The unit will temporarily disregard customized listening mode settings For system optimization using DACS and a JBL Synthesis Digital Equalizer connect the left and right RCA outputs of the DACS signal generator EVP 1 to the 1 analog input which is active in the TAPE input and set the front panel volume level to OdB This will provide the correct signal path and reference output level 3 27 The SETUP Menu JBL MAIN MENU gt SETUP gt SPEAKER SETUP gt LEVELS CALIBRATION gt SUB LIMITERS MODE ADJUST INPUTS CUSTOM SETUP INTERNAL NOISE TEST CAL NOISE ON AUDIO CONTROLS SYNTHESIS 7CH SETUP DACS CALIBRATION UR LIMITER OFF REAR PANEL CONFIG SPEAKER DISTANCES L R LIMIT ADJ 100dB DISPLAYS LFE LIMITER OFF VOLUME CONTROLS E m LFE LIMIT ADJ 100dB TRIGGERS qz LOCK OPTIONS o ICAUTION X HIGH AUDIO LEVELS 2 0 1 LEVELS CALIBRATION continued Ty gt Emus gt SDP 40 Balanced output levels must be recalibrated when output connections are changed from DACS CALIBRATION continued unbalanced to balanced or vice versa The balanced Before making adjustments set the SPL meter according to
25. LOGIC MONO SURROUND USE LAST E EZ L explained in further detail in Section 5 Note When the 2 CH parameter is set to USE LAST pressing the 2CH button on the remote control selects the 2 CHANNEL listening mode However pressing the 2CH button again does not select the previous listening mode To deselect the 2 CHANNEL listening mode press another mode family selection button on the remote control or reselect the input See page 2 for more information about the 2CH button dts ES EX EN EZ Selecting dts ES accesses the dts ES MODE menu pictured on the bottom of the next page which can be used to select the listening mode for dts ES input types Listening modes are explained in further detail in Section 5 Selecting DOLBY D accesses the DOLBY D MODE menu pictured on the top of the next page which can be used to select the listening mode for Dolby Digital input types Listening modes are 3 10 SDP 40 The SETUP Menu MAIN MENU gt SETUP gt INPUT SETUP DVD1 INPUT SETUP DVD1 D MODE MODE ADJUST NAME DVD1 5 1 157 FILM AUDIO CONTROLS SPEAKERS DVD2 DIGITAL IN COAX 1 5 1157 TV REAR PANEL CONFIG LD ANALOG IN NONE 5 1 1 MUSIC DISPLAYS TV ANLG IN LVL AUTO 5 1 THX SUR EX VOLUME CONTROLS SAT VIDEO IN S VIDEO 1 DIGITAL TRIGGERS VCR COMPONENT IN 1 5 1 2 CHANNEL LOCK OPTIONS CD 2 CH L7 FILM 5 1 MO
26. Menu 5 19 DOLBY PRO LOGIC 5 5 DOLBY PRO LOGIC II MUSIC 5 5 DOLBY PRO LOGIC II THX 2 17 5 4 DOLBY PRO LOGIC II 2 17 5 4 dts Button 2 14 2 16 to 2 17 dts STATUS Menu 5 20 dts ES 2 CHANNEL 5 15 dts ES LOGIC7 FILM 2 17 5 13 dts ES LOGIC7 MUSIC 2 17 5 14 dts ES Listening Mode 2 17 5 15 dts ES Parameter 2 16 3 10 to 3 11 dts ES 2 17 5 14 DVD1 Button 2 3 2 9 DVD2 Button 2 3 2 9 Index JBL EDIT CUSTOM NAME 3 33 LFE LMITAD A 3 29 Mode Parameter Descriptions 5 20 to 5 24 EDIT INPUT NAME 3 4 LFEMLIMITER e es 3 29 Mode Selection 2 16 to 2 17 EFFECT EVI ae RR 5 22 A ETE US 5 23 Mode Up and Down Buttons 2 3 2 16 to 2 17 ENCODING 5 5 22 ok gat 2 8 MODES ES 3 36 ES DECODE ES ERE ERES 5 22 Limited Warranty Inside Back Cover 559 x E 5 7 Factory Default Settings Restoring 1 5 6 4 Listening Mode see also Mode 2 042564 m m m RE 4 5 7 FADER eet rt aede s 2 12 2 13 4 4 Listening Mode Descriptions
27. The MICROPHONE INPUTS are provided for future expansion Four 3 5mm T R S or balanced inputs are available The TRIGGER OUTPUTS provide DC output These outputs are available on a 5 pin DIN connector The PWR trigger is on when the unit is on and off when the unit is in standby or off Triggers 1 and 2 can be configured in the TRIGGER SETUP menu see page 3 35 The default trigger settings are preconfigured for use in JBL Synthesis systems with switching transducers for cinema and music modes GROUND TRIGGER 2 TRIGGER 1 GROUND POWER TRIGGER The RS 232 Connector labelled 1 is provided for serial control and software upgrades The RS 232 connector labelled 2 is provided for future expansion The IR IN Connector is provided for input of infrared data from industry standard infrared distribution equipment A 3 5mm T R S input is available A Removable Access Panel is provided for future expansion Basic Operation REMOTE CONTROL The SDP 40 remote control pictured at the left provides full operation of the unit executing functions such as on screen menu navigation that are not available from the front panel For best results make sure the front panel IR Receiver window is not obstructed see pages 2 2 and 2 6 for illustrations The remote control must be in line of sight with this receiver for proper operation If the unit is placed inside a glass cabinet smoked glass will reduce the range of the remote c
28. USE LAST 3 COMPONENT 4 When REAR PANEL is set to 5 STEREO amp 5 1 ANLG 5 1 ANALOG will appear in place of these menu items JBL Appendix SPEAKER SETUP CUSTOM SETUP SYNTHESIS 7CH SETUP SPEAKER DISTANCES LEVELS CALIBRATION CUSTOM SETUP SYNTHESIS 7CH SETUP i Es T SPEAKER DISTANCES LEVELS CALIBRATION 404 FRONT L R 80Hz PRESSING THE RIGHT q FRONT LEFT 0 0 INTERNAL NOISE TEST CENTER 80Hz BUTTON WILL Da Si 0 0 DACS CALIBRATION SIDE LR 80Hz AUTOMATICALLY CHANGE du 2 FRONT RIGHT 0 0 SUB LIMITERS REAR L R 80Hz THE OUTPUTS TO A EN ORDES SIDE RIGHT 0 0 SUB UR MONO SYNTHESIS 7CH SPEAKER pag REAR RIGHT 0 0ft Continued on page A 9 SUB XOVER 80Hz CONFIGURATION REAR LEFT 0 0ft LFE OFF SIDE LEFT 0 0ft SUB MONO 0 0ft SYNTHESIS 7CH SETUP SUB RIGHT 004 SUB Of FRONT L R 80Hz S PEE CENTER 80Hz SIDE L R 80Hz When SUB L R is set to REAR L R 80Hz STEREO or NONE see page SUB L R MONO 3 22 the SUB MONO SUB XOVER 80Hz parameter will appear as LFE OFF SUB LEFT FRONT L R SPEAKERS CENTER SPEAKER SIDE L R SPEAKERS REAR L R SPEAKERS SUBWOOFERS L R SUB XOVER FULL FULL FULL FULL MONO FULL 30Hz 30Hz 30Hz 30Hz STEREO 30Hz 40Hz 40Hz 40Hz 40Hz NONE 40Hz 50Hz 50Hz 50Hz 50Hz 50Hz 60Hz 60Hz 60Hz 60Hz 60Hz 70H
29. a connect or selected for both the DIGITAL IN and ANALOG IN parameters This setting is recommended for input sources that utilize both digital and analog audio input types such as a laser disc player Note Some sources supply valid digital audio input types that remain active even when no audio is present in the signal Because the unit recognizes these as valid digital audio input types it will not switch to the ANALOG IN connector For these sources it is recommended to configure two different inputs one for digital audio input types and a second for analog audio input types ANLG IN LVL 18 to 12dB ANLG IN LVL allows manual adjustment of the analog input level of the RECORD AUDIO OUTPUT labelled S PDIF It is used to prevent the internal analog to digital converter from overloading It can be adjusted while listening to an input source When ANLG IN LVL is selected a white horizontal bar graph will appear on the screen below the ANLG IN LVL parameter This graph illustrates the position at which the current setting falls within the 18 to 12dB parameter range Press the up and down MENU arrows to increase and decrease the setting in increments Press the left MENU arrow to close the graph and return to the RECORD ADV menu DIGITAL BYPASS ON OFF DIGITAL BYPASS allows direct digital recording When set to ON the unit passes the digital input signal unaltered to the S PDIF outputs When set to OFF t
30. de ventilaci n y nunca deje caer ning n l quido sobre la unidad Este producto est equipado con un enchufe de 3 clavijas con conexi n a tierra ste es un elemento de seguridad que no debe ser eliminado Nunca conecte ning n tipo de salida de amplificadores de sonido directamente a los conectores de la unidad Para prevenir descargas el ctricas o incendios mantenga la unidad alejada de la lluvia humedad o cualquier lugar en el que pueda entrar en contacto con agua No trate de hacer funcionar la unidad si se ha ca do est da ada ha entrado en contacto con l quidos o si nota cualquier cambio brusco en su funcionamiento que indique la necesidad de hacerle un servicio de mantenimiento Esta unidad deber ser abierta nicamente por personal calificado Si usted quita las coberturas se expondr a voltajes peligrosos Este tri ngulo que aparece en su componente le advierte sobre la existencia dentro del chasis de voltajes peligrosos sin aislantes voltajes que son lo suficientemente grandes como para causar electrocuci n Este tri ngulo que aparece en su componente lo alerta sobre las instrucciones de operaci n y mantenimiento importantes que est n en los materiales de lectura que se incluyen vii Introduction JBL FRANCAIS INSTRUCTIONS DE S RET IMPORTANTES Gardez ces instructions pour r ference future Observez toutes les instructions et tous les avertissements marqu s sur l a
31. front panel or the remote control The INPUT SETUP menu can be used to select a preferred 2 channel Dolby Digital and dts ES listening mode for each input When an input type is recognized the unit automatically defaults to the appropriate listening mode See page 3 3 for more information about the INPUT SETUP menu See Section 5 for more information about listening modes For example the 2 CH parameter on the INPUT SETUP menu is set to LOGIC7 FILM and the DOLBY D parameter is set to 5 1 LOGIC7 MUSIC When the input type changes from 2 channel to Dolby Digital the listening mode will automatically change from LOGIC7 FILM to 5 1 LOGIC7 MUSIC JBL MODE BUTTONS This type of listening mode selection occurs each time the Mode Up and Down buttons are pressed on the front panel or the MODE buttons are pressed on the remote control This type of mode scrolling allows auditioning of all listening modes available for the current input type Pressing the Mode Up MODE button selects the previous listening mode on the list Pressing the Mode Down MODE button selects the next listening mode on the list 2 channel listening modes are listed on page 3 10 Dolby Digital and dts ES listening modes are listed on page 3 11 These lists are not visible on the on screen and front panel displays during scrolling Note When the input type changes the unit will automatically revert to the default listening modes selected in the IN
32. gt 40dB Differential Gain lt 0 5 Differential Phase lt 0 5 Bandwidth gt 25MHz K Factor lt 0 3 Gain 0 15dB Signal Noise Ratio gt 70dB Frequency Response 10Hz to 10MHz 0 1 0 3dB Performance Component Video 3 channel Y Pr Pb format independent Switching Passive Impedance 750 Bandwidth gt 300MHz Insertion Loss 3dB Other Microphone Inputs Input sensitivity Input Impedance 4 3 5mm miniature phone jacks 10mVrms 400mV maximum input level 20kQ accepts balanced or unbalanced input signals Trigger Outputs 1 power on off trigger 2 programmable triggers 12 VDC 0 5 amps each detachable screw terminals RS 232 Serial Input Output 2 9 pin D sub connectors for system control and software upgrades Power Requirements 90 250 VAC 50 60Hz 90W universal line input detachable power cord Dimensions Width 17 3 inches 440mm Height 6 63 inches 169mm Depth 14 85 inches 377mm Weight 45lbs 20 5kg Rack Mounting Brackets are available for mounting the unit in a standard 19 inch equipment rack Other continued Environment Operating Temp Storage Temp Relative Humidity 0 to 35 C 32 to 95 F 30 to 75 C 22 to 167 F 95 maximum without condensation Remote Control Batteries Hand held battery powered infrared remote control unit Two AA Appendix J
33. inputs The trigger labelled PWR is not configurable and is always on when the unit is on and always off when the unit is in standby or off The TRIGGER OUTPUTS labelled 1 and 2 represent the two configurable triggers on the unit and can be programmed for REMOTE or PROGRAM operation in the TRIGGER SETUP menu Selecting the TRIGGERS option on the SETUP menu prompts the selection of the desired TRIGGER for configuration Selecting either TRIGGER 1 or TRIGGER 2 accesses the TRIGGER SETUP menu pictured at the right Use the up and down MENU arrows to scroll through the menu items Press the right MENU arrow to select the highlighted MENU arrow then use the up and down MENU arrows to toggle between the ON and OFF settings Press the left MENU arrow to select the desired setting REMOTE OPERATION When the REMOTE parameter is set to ON the selected trigger will be configured for REMOTE operation The unit will ignore all other parameter settings on the TRIGGER SETUP menu Use the remote control commands described on page 2 12 to activate and deactivate the selected trigger When the REMOTE parameter is set to OFF the selected trigger will automatically be configured for PROGRAM operation PROGRAM OPERATION When the REMOTE parameter is set to OFF the selected trigger will automatically be configured for PROGRAM operation Triggers can be activated upon the selection of associated Main Zone inputs Zone 2 input selection Record Zone input selection a
34. ja palovaaran v ltt miseksi yksikk ei saa olla sateessa tai kosteassa eik sit saa k ytt m r ss ymp rist ss e l k yt yksikk jos se on pudonnut vaurioitunut kostunut tai jos sen suorituskyky on huomattavasti muuttunut mik vaatii huoltoa e Yksik n saa avata vain laitteeseen perehtynyt huoltohenkil Kansien poisto altistaa sinut vaarallisille j nnitteille T m kolmio joka esiintyy komponentissasi varoittaa sinua AN erist m tt m n vaarallisen j nnitteen esiintymisest yksik n sis ll T m j nnite saattaa olla riitt v n korkea aiheuttamaan s hk iskuvaaran T m kolmio joka esiintyy komponentissasi kertoo sinulle ett t ss tuotedokumentoinnissa esiintyy t rkeit k ytt ja yll pito ohjeita Introduction NORSK VIKTIG INFORMASJON OM SIKKERHET Ta vare p denne veiledningen for senere bruk Felg alle anvisningene og advarslene som er angitt p apparatet Apparatet skal alltid anvendes med korrekt spenning Produktbeskrivelsen inneholder spesifikasjoner for stremkrav V r oppmerksom pa at det ved ulike driftsspenninger kan v re n dvendig bruke en annen ledning og eller st pseltype e Apparatet skal ikke monteres i skap uten ventilasjon eller direkte over varmeproduserende utstyr som for eksempel kraftforsterkere Den maksimale romtemperaturen som st r oppgitt i produktbeskrivelsen skal overholdes e Apparatet er utstyr
35. o o 5 Toggles between 7 and 5 channel playback Reserved for future expansion Reserved for future expansion Reserved for future expansion e Toggles between the selected listening mode and the 2 CHANNEL listening mode Reserved for future expansion Reserved for future expansion Reserved for future expansion See Section 5 for more information about listening modes See Section 4 for more information about these AUDIO CONTROLS menu parameters Basic Operation BANK JBL 6 Family Selection Buttons 6 6 6 Selects the THX mode family Reserved for future expansion Reserved for future expansion Toggles the SURROUND EX parameter ON and OFF Selects the Dolby Reserved for Reserved for Reserved for mode family future expansion future expansion future expansion Selects the Reserved for Reserved for Reserved for LOGIC7 film future expansion future expansion future expansion mode family Selects the Reserved for Reserved for Reserved for LOGIC7 TV future expansion future expansion future expansion mode family Selects the Reserved for Reserved for Reserved for dts ES mode family future expansion future expansion future expansion Selects the LOGIC7 music mode family Reserved for future expansion Reserved for
36. only one pair of surround speakers is selected Default Parameter Value Values VOCAL ENHANCE 0 0dB 0 0 3 0dB 6 0dB 5 SPKR ENHANCE OFF ON OFF BASS ENHANCE OFF ON OFF RE EQUALIZER OFF ON OFF REAR DLY OFFSET 15ms 0 to 30ms COMPRESSION OFF AUTO ON OFF LFE MIX 0 0dB 10 0 to 0 0dB OUTPUT LEVELS See page 5 17 for more information CUSTOM See page 5 17 for more information An alphabetical listing of parameter descriptions begins on page 5 20 5 1 LOGIC7 MI MODE ADJUST 5 A proprietary Lexicon listening mode e Designed for playback of 5 1 channel Dolby Digital music sources e Based on 5 1 LOGIC7 FILM but specifically tailored for music sources e Recommended for 5 1 channel Dolby Digital music sources even when only one pair of surround speakers is selected Default Parameter Value Values VOCAL ENHANCE 0 0 0 0 3 0dB 6 0dB 5 SPKR ENHANCE OFF ON OFF BASS ENHANCE OFF ON OFF RE EQUALIZER OFF ON OFF REAR DLY OFFSET 15ms 0 to 30ms COMPRESSION OFF AUTO ON OFF LFE MIX 0 0dB 10 0 to 0 0dB OUTPUT LEVELS See page 5 17 for more information CUSTOM See page 5 17 for more information An alphabetical listing of parameter descriptions begins on page 5 20 The MODE ADJUST Menu JBL 5 1 THX SURROUND EX or 5 1 THX ARI gt 5 1 1X SUR EX The SURROUND EX parameter activates and deactivates the 5 1 THX SURROUND EX listening mode prov
37. path any other input may be substituted NAME E o E Selecting NAME accesses the INPUT NAME menu which can be used to customize and restore input names EDIT INPUT NAME EDIT INPUT NAME allows the customization of INPUT NAME input names Selecting this option accesses the pulldown menu pictured at the right EDIT INPUT NAME DVD1 BUTTONS TO EDIT Use the up and down MENU arrows to change the character above the Up to rep tn eight characters including blank spaces can be entered Use the right MENU arrow to advance to the next character The will automatically wrap to the first character space after the eighth character space is passed When finished press the left MENU arrow to close the pulldown menu The input name will change on the on screen and front panel displays However the input name will not change on the INPUT SETUP menu that prompts the selection of the desired input for configuration pictured above third menu from the left RESTORE DEFAULT NAME RESTORE DEFAULT NAME restores the factory default name of the selected input Factory default names correspond to the labels on the front panel and remote control Selecting this option accesses a pulldown menu that reads PRESS MENU gt TO RESTORE INPUT NAME Press the right MENU arrow to restore the factory default name of the selected input Press the left MENU arrow to
38. the outputs are approximately 6dB louder than the DACS Installers Manual or audio calibration disc instructions If no unbalanced outputs setting is recommended set the SPL meter to C weighting and SLOW response Use the up and down MENU arrows to SUB LIMITERS manually scroll through menu items Press the right MENU arrow to select an output for adjustment then use the up and down MENU arrows to increase and decrease the level of the selected output in 0 548 increments within a range of 18 to 12dB Adjust all output levels to achieve the appropriate reading on the SPL meter from the primary listening position Press the left MENU arrow to exit the selected output and return to the SPEAKER LEVEL ADJUST menu Dolby Digital and dts ES input types can produce low frequency peaks at much higher levels than 2 channel input types In home listening spaces the subwoofer and its associated amplifier are sometimes unable to reproduce these levels without overloading For this reason the unit is equipped with internal sub limiters that help prevent subwoofer signals from exceeding a designated value This parameter can be adjusted within a 75 to 115dB range Separate limiters are provided for the SUBWOOFER L R and the LFE outputs 3 28 The SETUP Menu SDP 40 Default Parameter Value Values CAL NOISE ON ON OFF L R LIMITER OFF ON OFF L R LIMIT ADJ 100dB 75 to 115dB LFE LIMITER OFF ON OFF LFE LIMIT ADJ
39. to be used as an example throughout this section Whenever DVD1 appears as a step in a menu path any other input may be substituted VIDEO IN 6 DEI ME Selecting VIDEO IN accesses the VIDEO IN menu which can be used to select the composite video or S video connector associated with the selected input Note Composite video outputs are available when composite or S video inputs are used S video outputs are only available when S video inputs are used Output 1 OSD incorporates the on screen display output 2 does not DVD1 VIDEO IN COMPOSITE 1 COMPOSITE 2 COMPOSITE 3 COMPOSITE 4 COMPOSITE 5 S VIDEO 1 S VIDEO 2 S VIDEO 3 S VIDEO 4 S VIDEO 5 S VIDEO 6 S VIDEO 7 S VIDEO 8 NONE The SETUP Menu SDP 40 MAIN MENU gt SETUP INPUT SETUP DVD1 INPUT SETUP DVD1 COMPONENT MODE ADJUST NAME DVD1 COMPONENT 1 AUDIO CONTROLS SPEAKERS DVD2 DIGITAL IN COAX 1 COMPONENT 2 REAR PANEL CONFIG LD ANALOG IN NONE COMPONENT 3 DISPLAYS TV ANLG IN LVL AUTO COMPONENT 4 VOLUME CONTROLS SAT VIDEO IN S VIDEO 1 TRIGGERS VCR COMPONENT IN 1 LOCK OPTIONS CD 2 CH L7 FILM PVR 000 5 1 L7 FILM GAME TAES dts L7 FILM TAPE MAIN ADVANCED TUNER ZONE2 ADVANCED AUX RECORD ADVANCED DVD1 is used as an example in this illustration and will continue to be used as an example throughout this section Whenever DVD1 appears
40. 100dB 75 to 115dB Note In cases where the left and right subwoofers have built in limiter protection the L R LIMITER parameter should be set to OFF In cases where the LFE subwoofer has built in limiter protection the LFE LIMITER parameter should be set to OFF CAL NOISE ON OFF CAL NOISE determines whether limiters will be set using an internal or external noise signal When set to ON the unit activates the internal calibration noise to set the limiters When set to OFF the unit deactivates the internal calibration noise requiring the use of an audio calibration disc to set the limiters L R LIMITER ON OFF L R LIMITER affects the SUBWOOFER L R outputs as well as any low frequency signals redirected to other MAIN AUDIO OUTPUTS When set to ON these outputs will be restricted to the limit specified in the L R LIMIT ADJ parameter When set to OFF the output level of these outputs will not be restricted The L R LIMITER should be set to OFF when the left and right subwoofers have built in limiter protection L R LIMIT 75 to 115dB L R LIMIT ADJ specifies the output level restriction placed on the SUBWOOFER L R outputs as well as any low frequency signals redirected to other MAIN AUDIO OUTPUTS when the L R LIMITER parameter is set to ON Press the right MENU arrow to select this parameter for adjustment Its setting will automatically change to 75dB Use the up and down MENU arrows to increase and decrease the s
41. 4 bits PCM audio Dolby Digital dts and dts ES discrete data formats Main Audio Outputs 12 unbalanced RCA and 12 balanced XLR for Front L R Center LFE Subwoofer L R Side L R Rear L R Auxiliary L R Zone 2 Audio Outputs 2 stereo pairs RCA one fixed and one variable output level 2 balanced XLR for L R variable output Record Audio Outputs 2 stereo pairs RCA one fixed and one variable output level 1 coaxial RCA and 1 optical TosLink S PDIF output in parallel Performance Main Zone Analog to Digital Conversion 24 bit 96kHz dual bit AY architecture Digital to Analog Conversion 24 bit 44 1 to 192kHz multi bit architecture operating in dual mono mode Frequency Response 10Hz to 20kHz 0 1dB 0 25dB 0 75dB at 40 kHz reference 1kHz THD Noise Below 0 00896 at 1kHz maximum output level Dynamic Range 108dB minimum 111dB typical 22kHz bandwidth Signal to Noise Ratio 108dB minimum 111dB typical 22kHz bandwidth Input Sensitivity 200mVrms 2Vrms for maximum output level at OdB input gain Input Impedance 100kQ in parallel with 150pF Output Level 150mVrms typical 6Vrms maximum RCA outputs 300mVrms typ 12Vrms maximum XLR outputs maximum value with full scale input signal and volume at 6dB Output Impedance 1000 in parallel with 150pF RCA outputs 500 in parallel with 150pF XL
42. AL 6 ANALOG IN NONE ANALOGIN ANALOG2 ANALOGIN 09 4 ANALOGIN 5 ANALOGIN ANALOG 1 ANALOG IN NONE ANLG IN LVL AUTO ANLG IN LVL AUTO ANLG IN LVL AUTO ANLG IN LVL AUTO ANLG IN LVL AUTO ANLG IN LVL AUTO VIDEO IN S VIDEO 2 VIDEO IN S VIDEO 4 VIDEO IN S VIDEO 6 VIDEO IN S VIDEO 7 VIDEO IN VIDEOIN COMPOSITE 3 COMPONENT IN 2 COMPONENT IN 3 COMPONENT 1 COMPONENT IN 1 COMPONENT IN 1 COMPONENT IN 1 2 CH L7 FILM 2 CH L7TV 2 CH L7 FILM 2 CH L7TV 2 DO PRO LOGIC 2 L7 MUSIC oa D 5 1 L7 FILM 000 5117TV 000 51L7FILM 000 5117 000 5 1 L7 MUSIC 000 5 1 L7 MUSIC EEs dts L7 FILM Eres dts L7 FILM Eres dts L7 FILM ESE dts L7 FILM dts L7 MUSIC AEs dts L7 MUSIC MAIN ADVANCED MAIN ADVANCED MAIN ADVANCED MAIN ADVANCED MAIN ADVANCED MAIN ADVANCED ZONE2 ADVANCED ZONE2 ADVANCED ZONE2 ADVANCED ZONE2 ADVANCED ZONE2 ADVANCED ZONE2 ADVANCED RECORD ADVANCED RECORD ADVANCED RECORD ADVANCED RECORD ADVANCED RECORD ADVANCED RECORD ADVANCED 40 Appendix DVD1 INPUT SETUP The DVD1 INPUT SETUP menu is used as an example on this page The menus pictur
43. AR the SIDE L R and REAR L R outputs are not attenuated preserving the intended balance of the sound field SUB L R and SUB L R LVL OFF 30 to 12dB SUB L R Subwoofer Left Right and SUB L R LVL Subwoofer Left Right Level adjust the output level of the SUBWOOFER L R outputs SURR ROLLOFF 500Hz to 20 0kHz OFF SURR ROLLOFF Surround Rolloff simulates the high frequency rolloff that occurs in real spaces When set within its 500Hz to 20kHz range the unit applies a high frequency rolloff to the SIDE L R and REAR L R outputs When set to OFF the unit does not apply this high frequency rolloff SURROUND DLY 0 to 15ms SURROUND DLY Surround Delay increases the perceived depth of the listening space by delaying the arrival time of the SIDE L R and REAR L R outputs This time delay can be set within a range of 0 to 15ms Increasing this time is recommended when a greater sense of depth is desired in the listening space SURROUND EX ON OFF SURROUND EX activates and deactivates the 5 1 THX SURROUND EX listening mode provided both side and rear speakers are select ed see page 3 18 The default value of the SURROUND EX parameter is ON which activates 5 1 THX SURROUND EX When set to OFF the 5 1 THX SURROUND EX listening mode becomes 5 1 THX See page 5 10 for more information Toggling the setting of the SURROUND EX parameter produces low level clicks in the front speakers SURROUND MIX 5 to 5dB SURROUND MIX
44. AUTO ON OFF LFE MIX 0 0dB 10 0 to 0 0dB OUTPUT LEVELS See page 5 17 for more information CUSTOM See page 5 17 for more information An alphabetical listing of parameter descriptions begins on page 5 20 5 1 2 CHANNEL MODE ADJUST fg 5 1 2 CHANNEL Designed for conversion of 5 1 channel Dolby Digital input types to LOGIC7 encoded 2 channel output types e Allows 5 1 channel Dolby Digital sources to be listened to through the front left and right channels e the original 5 1 performance through playback of LOGIC7 listening modes e Recommended for recording purposes Default Parameter Value Values CENTER MIX 0dB 25 to 5dB SURROUND MIX 0dB 5 to 5dB CNTR DLY SAMPLES 0 127 to 127 MASTER LEVEL 0dB 5 to 5dB COMPRESSION OFF AUTO ON OFF LFE MIX 0 0dB 20 0 to 0 0dB SUB L R LVL 0dB OFF 30 to 12dB CUSTOM See page 5 17 for more information An alphabetical listing of parameter descriptions begins on page 5 20 The MODE ADJUST Menu JBL 5 1 IMODE ADJUST 5 1 Mono e Designed for playback of Dolby Digital mono sources e Sends mono sources to the center channel only No parameters are available for the MONO listening mode Note The 5 1 MONO 5 1 MONO LOGIC and 5 1 MONO SURR listening modes are designed for playback of Dolby Digital mono sources Mono material can be found on both Dolby Digital 1 0 and 2 0 input types These mod
45. BL Application of Council Directive s Standard s to which Conformity is Declared Manufacturer Type of Equipment Model Date DECLARATION OF CONFORMITY 89 336 EEC and 93 68 EEC EN55022 1998 EN55024 1998 EN6100 3 2 and 3 1999 and EN60065 1998 Lexicon Inc 3 Oak Park Bedford MA 01730 1441 USA The equipment identified here conforms to the Directive s and Standard s specified above SDP 40 Digital Surround Processor Controller JBL Synthesis SDP 40 June 1 2001 Lexicon Inc Vice President of Engineering 3 Oak Park Bedford MA 01730 1441 USA Tel 781 280 0300 Fax 781 280 0490 40 Appendix MENU TREE MAIN MENU MODE ADJUST AUDIO CONTROLS SETUP MODE ADJUST AUDIO CONTROLS SETUP tz FILM BASS 80048 INPUTS 15 TV TREBLE 40 0dB SPEAKERS 121 MUSIC TILT EQ 80048 REAR PANEL CONFIG DO PL i THX LOUDNESS ON DISPLAYS PRO LOGIC BALANCE lt gt VOLUME CONTROLS DO PL II MUSIC FADER lt gt TRIGGERS PRO LOGIC ZONE2 BALANCE lt gt LOCK OPTIONS 2 CHANNEL RECORD BALANCE lt gt PARTY MONO MONO LOGIC B 1 INPUT SETUP SPEAKER SETUP REAR PANEL CONFIG DISPLAY SETUP 3 x ad DVD CUSTOM SETUP 8 STEREO INPUTS ON SCREEN DISPLAY P Ne DVD2 SYNTHESIS 7CH SETUP OR FRONT PANEL DISPLAY i m E LD SPEAKER DISTANCES 5 STEREO amp 5 1 ANLG A V SYNC DELAY OFF a
46. BL Synthesis customer service at 818 830 8757 Note Visit www jblsynthesis com for additional information Troubleshooting and Maintenance JBL RESTORING FACTORY DEFAULT SETTINGS The procedure below outlines the process to restore factory default settings Before performing these steps record custom settings on the installation worksheet see page A 12 All parameters will be reset to their factory default value This procedure should be performed before setup begins To restore factory default settings 1 Record user defined settings on the installation worksheet see page A 12 2 If the unit is on place it into standby by pressing the amp standby button on the remote control If the unit is in standby skip ahead to Step 3 3 Power the unit on by pressing the standby button on the remote control 4 Quickly press and hold the MUTE button on the remote control until the following hidden menu appears FACTORY SETTINGS EXIT RESTORE DEFAULTS The MUTE button must be pressed within 3s of powering the unit on If the message MUTE ON appears in the top left corner of the screen when the MUTE button is pressed too much time has passed Begin again with Step 2 5 Usethe up and down MENU arrows to highlight RESTORE DEFAULTS then press the right MENU arrow to restore factory default settings Selecting the EXIT option with the right MENU arrow will cancel the restoration of
47. DIGITAL SPEAKERS DVD2 DIGITAL IN COAX 1 ANALOG BYPASS OFF REAR PANEL CONFIG LD ANALOG IN NONE S VIDEO 16 9 AUTO DISPLAYS TV ANLG IN LVL AUTO S VIDEO OSD 4 3 ON VOLUME CONTROLS SAT VIDEO IN S VIDEO 1 COMPONENT OSD OFF TRIGGERS VCR COMPONENT IN 1 LOCK OPTIONS CD 2 CH L7 FILM PVR DO D 5 1 L7 FILM GAME TAES dts L7 FILM TAPE TUNER ZONE2 ADVANCED AUX RECORD ADVANCED DVD1 is used as an example in this illustration and will continue to be used as an example throughout this section Whenever DVD1 appears as a step in a menu path any other input Note O 5 5 RS Selecting MAIN ADVANCED accesses the MAIN ADV menu which can be used to configure advanced settings in the Main Zone Default Parameter Value Values INPUT SELECT DIGITAL AUTO ANALOG DIGITAL ANALOG BYPASS OFF ON OFF S VIDEO 16 9 AUTO AUTO OFF S VIDEO 4 3 OSD ON ON OFF COMPONENT OSD OFF ON OFF The unit will automatically select the 5 1 BYPASS listening mode when all of the following conditions are met e 5 STEREO amp 5 1 is selected on the REAR PANEL CONFIG menu see page 3 30 e ANALOG IN parameter on the INPUT SETUP menu is set to 5 1 ANALOG see page 3 6 e The INPUT SELECT parameter on the MAIN ADV menu is set to either AUTO or ANALOG When set to AUTO no digital input types can be present e ANALOG BYPASS parameter on the MAIN ADV menu is set to ON JBL 3 12 SDP 40 The SETUP Menu
48. Dem TV LEVELS CALIBRATION CUSTOM NAME OFF 118 d EDIT CUSTOM 5 1 MONO CD Continued on page A 9 5 1 MONO LOGIC PVR Q o 5 1 MONO SURR Um AME oh vA 15 FILM a ED reges 15 MUSIC TUNER E5 THX Continued 8 UX ESES 2 CHAN Continued on page A 6 5 1 BYPASS 2CH BYPASS Continued on page A 10 VOLUME CONTROL SETUP TRIGGER SETUP LOCK OPTIONS MAIN PWR ON 30dB TRIGGER 1 PROGRAM MODES UNLOCKED MUTE LEVEL FULL TRIGGER 2 PROGRAM AUDIO CNTRL UNLOCKED ZONE PWR ON 30dB SETUP UNLOCKED BEC PWR ON 30d8 Continued on page A 9 A 5 Appendix JBL Continued from page 5 The menu pictured at the left prompts the selection of the desired input for configuration Selecting an input accesses the corresponding INPUT SETUP menu pictured below The parameters on the left side of this menu are identical DESIT regardless of which input is selected The values on the right side of the menu can be adjusted Selecting a parameter DVD1 for adjustment accesses the corresponding menu pictured on the next page DVD2 LD TV SAT VCR CD PVR GAME DVD1 INPUT SETUP LD INPUT SETUP SAT INPUT SETUP CD INPUT SETUP GAME INPUT SETUP TUNER INPUT SETUP TUNER ie NAME DVD1 NAME LD SAT NAME GAME NAME TUNER DIGITAL IN COAX 1 DIGITAL IN COAX 3 DIGITAL IN OPT
49. E lt gt MENU arrow to select the highlighted FADER lt gt SONES BALANCE gt parameter for adjustment Press the left RECORD BALANCE lt gt MENU arrow to return to the MAIN MENU Default Parameter Value Values BASS 0 0dB 6 0 to 6 0dB TREBLE 0 0dB 6 0 to 6 0dB TILT EQ 0 0dB 3 0 to 3 0dB LOUDNESS ON ON OFF BALANCE lt l gt L lt lt l gt gt R FADER lt l gt B lt lt l gt gt F ZONE2 BALANCE lt l gt L lt lt l gt gt R RECORD BALANCE lt l gt L lt lt l gt gt R Scale shown below When FADER is selected the L will be replaced by a B and the R will be replaced by an F BASS 6 0 to 6 0dB AUDIO CONTROLS ER BASS controls the amount of low frequency boost or cut applied to the FRONT L R CENTER SUBWOOFER L R and LFE outputs When BASS is selected a horizontal graph will appear on the screen below the parameter This graph illustrates the position at which the current setting falls within the 6 0 to 6 0dB parameter range Press the up and down MENU arrows to increase and decrease the setting in 0 5dB increments Press the left MENU arrow to close the graph and return to the AUDIO CONTROLS menu The graph pictured below shows the frequency response of all BASS settings A
50. EO INPUTS 5 STEREO amp 5 1 ANLG SETTING CENTER 80Hz TRIGGER 1 SIDE L R 80Hz DISPLAY SETUP TRIGGER 2 REAR L R SETTING SUB L R MONO On Screen LOCK OPTIONS SUB XOVER 80Hz STATUS SETTING LFE OFF POSITION MODES OUTPUT LEVEL DISTANCE FORMAT AUDIO CNTRL SETUP FRONT LEFT BACKGROUND CENTER REMOTE STATE AUDIO CONTROLS FRONT RIGHT Front Panel SETTING SIDE RIGHT STATUS BASS REAR RIGHT BRIGHTNESS TREBLE REAR LEFT A N SYNC DELAY TILT EQ SIDE LEFT SUB LEFT CUSTOM LOUDNESS CUSTOM NAME BALANCE SUB RIGHT FADER LFE CAL NOISE SETTING L R LIMITER L R LIMIT ADJ LFE LIMITER LFE LIMIT ADJ VOLUME CONTROL SETUP SETTING ZONE2 BALANCE RECORD BALANCE MAIN PWR ON MUTE LEVEL ZONE PWR ON REC PWR ON A 13 O Standby Button 2 2 2 8 A RUE eet 2 16 3 10 2 CHANNEL xin ehm 2 13 5 6 2 CHANNEL BYPASS 5 16 2CH Button i xke 2 13 2CH BYPASS STATUS Menu 5 18 2CH STATUS Menu 5 18 5 SPKR ENHANCE 5 20 5 STEREO 5 1 3 30 5 1
51. EQUALIZER OFF CENTER 008 VOCALENHANCE 0 0dB 5 SPKR ENHANCE OFF REAR DLY OFFSET 15ms SURROUND MIX 40dB 5 SPKRENHANCE OFF Continued from page 5 BASS ENHANCE OFF COMPRESSION OFF CNTRDLYSAMPLES 0 BASS ENHANCE OFF OUTPUT LEVELS LFE MIX B SURR ROLLOFF 153kHz CUSTOM 0 0d MASTER LEVEL 40dB REAR DLY OFFSET 15ms REAR DLY OFFSET 15ms OUTPUT LEVELS COMPRESSION OFF LFE MIX 40 0dB OUTPUT LEVELS CUSTOM LFE MIX 40 0dB OUTPUT LEVELS CUSTOM MONO SUB L R LVL 40dB CUSTOM CUSTOM NO PARAMETERS SDP 40 Appendix ADDITIONAL LISTENING MODE MENUS Eras THX RE EQUALIZER ON OUTPUT LEVELS 2 STATUS DIGITAL STATUS 5 1 ANALOG STATUS LFE MIX 40 0dB OUTPUT LEVELS CENTER 00B INPUT see page 5 18 CHANNELS see page 5 19 INPUT see page 5 19 CUSTOM SIDE L R 098 MODE see page 5 18 ENCODING see page 5 19 MODE see page 5 19 REAR L R 0dB INPUTTYPE see page 5 18 SAMPLE RATE 48kHz INPUT TYPE ANLG SUB L R 00B SAMPLE RATE see page 5 18 REF OFFSET dB SAMPLE RATE 96kHz traes LFE 0dB LEE MIX 40 008 See page 5 17 for more L R SL SR LFE L R SL SR LFE OUTPUT LEVELS information about the 6 CUSTOM OUTPUT LEVELS menu BR B 5 E E ETSE 2 CHA
52. ER should be set to ON for such film sources REAR DLY OFFSET 0 to 30ms REAR DLY OFFSET Rear Delay Offset increases the perceived depth of the listening space by delaying the arrival time of signals from the rear speakers This time delay can be set within a range of 0 to 30ms Increasing this time is recommended when using SIDE L R and REAR L R speakers that are located close together or when a greater sense of depth is desired in the listening space REAR L R OFF 30 to 12dB REAR L R Rear Left Right adjusts the output level of the REAR L R outputs REF OFFSET 4cB REF OFFSET Reference Offset indicates the dialog normalization value that is present in Dolby Digital input types SAMPLE RATE 44 1kHz 48kHz 88 2kHz 96kHz SAMPLE RATE indicates the sample rate of the input type SIDE L R OFF 30 to 12dB SIDE L R Side Left Right can be used to adjust the output level of the SIDE L R outputs 5 23 The MODE ADJUST Menu JBL SOUND STAGE FRONT NEUTRAL REAR SOUND STAGE dynamically adjusts the relative balance of the outputs when no surround signals are present When set to FRONT the SIDE L R and REAR L R outputs are attenuated shifting the per ceived balance of the sound field to the front of the listening space When set to NEUTRAL the SIDE L R and REAR L R outputs are attenuated slightly shifting the perceived balance of the sound field to the center of the listening space When set to RE
53. ER SETUP gt CUSTOM SETUP gt SIDE L R SPEAKERS MODE ADJUST INPUTS FRONT L R 80Hz FULL AUDIO CONTROLS SYNTHESIS 7CH SETUP CENTER 80Hz 30Hz REAR L R SPEAKERS REAR PANEL CONFIG SPEAKER DISTANCES SIDE L R 80Hz 40Hz DISPLAYS LEVELS CALIBRATION REAR L R 80Hz 50Hz FULL VOLUME CONTROLS Q Pe SUB L R MONO 60Hz 30Hz TRIGGERS SUB XOVER 80Hz 70Hz 40Hz LOCK OPTIONS Q o LFE OFF 80Hz 50Hz z THX 80Hz 60Hz amp iff M 90Hz 70Hz e D 100Hz 80Hz 110Hz THX 80Hz 120Hz 90Hz NONE 100Hz 110Hz 120Hz NONE SIDE L R FULL 30Hz to120Hz THX 80Hz NONE REAR L R FULL 30Hz to 120Hz THX 80Hz NONE The SIDE L R parameter sets the crossover setting for the MAIN AUDIO OUTPUTS labelled SIDE L R When set to FULL the unit sends a full range audio signal to the SIDE L R outputs When set to a numerical crossover setting the unit activates a crossover at the selected frequency Choose the setting closest to the low frequency rating of the side left and right speakers See pages 3 18 and 3 19 for more information about crossover settings When set to NONE the unit redirects side channel signals to the REAR L R outputs When both the SIDE L R and REAR L R parameters are set to NONE the unit redirects surround channel signals to the FRONT L R outputs The REAR L R parameter sets the crossover setting for the MAIN AUDIO OUTPUTS labelled REAR L R When set to FULL the unit sends a full range audio signal to the REAR L R outputs When set to a nu
54. FF SUBWOOFER L R is set to NONE LFE Low Frequency Effects activates and deactivates the MAIN AUDIO OUTPUT labelled LFE Selecting this parameter accesses the pulldown menu pictured above Use the up and down MENU arrows to switch between the ON and OFF settings Press the right MENU arrow to select the desired setting Press the left MENU arrow to close the pulldown menu and return to the CUSTOM SETUP menu When the LFE parameter is set to ON the unit sends the LFE channel to the LFE output When set to OFF the unit deactivates the LFE output and sends the LFE channel to the SUBWOOFER L R outputs If the SUBWOOFER L R outputs are set to NONE the LFE channel is sent to the MAIN AUDIO OUTPUTS with the lowest crossover setting FRONT L R is set to 40Hz and the rest of the MAIN AUDIO OUTPUTS are set to 60Hz The LFE channel will be sent to the FRONT L R outputs utilizing the 40Hz crossover point The SETUP Menu MAIN MENU MODE ADJUST AUDIO CONTROLS SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGERS LOCK OPTIONS SYNTHESIS 7CH SETUP e SPEAKERS 9 EMEEN JBL SPEAKER SETUP gt SYNTHESIS 7CH SETUP gt SYNTHESIS 7CH SETUP CUSTOM SETUP PRESSING THE RIGHT gt FRONT L R 80Hz SYNTHESIS 7CH SETUP BUTTON WILL CENTER 80Hz SPEAKER DISTANCES AUTOMATICALLY CHANGE SIDE L R 80Hz LEVELS CALIBRATION THE
55. FIG setting see page 3 30 When 8 STEREO INPUTS is selected on the REAR PANEL CONFIG menu the ANALOG IN menu will appear as it does in the illustration above When 5 STEREO amp 5 1 ANLG is selected on the REAR PANEL CONFIG menu ANALOG 6 7 and 8 on the ANALOG IN menu will be replaced with 5 1 ANALOG Note When ANALOG IN is set to NONE the INPUT SELECT parameter on the MAIN ADV menu is automatically set to DIGITAL see page 3 13 9 DU GN 9 Selecting ANLG IN LVL accesses the ANLG IN LVL menu which be used to adjust analog input levels Despite industry attempts at standardization analog sources have a wide range of output levels To compensate for this each of the eight analog inputs on the unit can be assigned a different analog input level This assures optimum performance regardless of source Default Parameter Value Values AUTO ON ON OFF MANUAL 0dB 18 to 12dB AUTO ON OFF AUTO provides automatic control of analog input levels When set to ON the unit monitors and automatically optimizes analog input 3 6 40 The SETUP Menu MAIN MENU gt SETUP gt INPUT SETUP gt DVD1 INPUT SETUP gt DVD1 ANLG IN LVL MODE ADJUST NAME DVD1 AUTO ON AUDIO CONTROLS SPEAKERS DVD2 DIGITAL IN COAX 1 MANUAL 40dB REAR PANEL CONFIG LD ANALOG IN NONE DISPLAYS TV ANLG IN LVL AUTO AUTO GAIN 0 048 VOLUME CONTROLS
56. ICAL 2 DIGITAL IN COAX 4 DIGITAL IN OPTICAL 4 DIGITAL IN NONE ANALOG IN ANALOGIN ANALOG ANALOGIN ANALOG 3 ANALOG IN ANALOGIN ANALOG 6 ANALOGIN ANALOG 8 ANLG IN LVL AUTO ANLG IN LVL AUTO ANLG IN LVL AUTO ANLG IN LVL AUTO ANLG IN LVL AUTO ANLG IN LVL AUTO VIDEO IN S VIDEO 1 VIDEO IN S VIDEO 3 VIDEO IN S VIDEO 5 COMPOSITE 1 VIDEOIN 2 VIDEO IN NONE COMPONENT IN 1 COMPONENT IN 1 COMPONENT 4 COMPONENT IN 1 COMPONENT IN 1 COMPONENT IN 1 2 CH L7 FILM 2 CH L7 FILM 2 CH L7TV 2 CH L7 MUSIC 2 L7 FILM 2 L7 MUSIC Dn D 5 117 FILM OOD 5 1 L7 FILM 00D 51L7TV 000 5 1 L7 MUSIC DOD 5 117 FILM 000 5 1 L7 MUSIC Ems dis L7 FILM dis L7 dis L7 dis L7 MUSIC dis L7 FILM dts L7 MUSIC MAIN ADVANCED MAIN ADVANCED MAIN ADVANCED MAIN ADVANCED MAIN ADVANCED MAIN ADVANCED ZONE2 ADVANCED ZONE2 ADVANCED ZONE2 ADVANCED ZONE2 ADVANCED ZONE2 ADVANCED ZONE2 ADVANCED RECORD ADVANCED RECORD ADVANCED RECORD ADVANCED RECORD ADVANCED RECORD ADVANCED RECORD ADVANCED DVD2 INPUT SETUP TV INPUT SETUP VCR INPUT SETUP PVR INPUT SETUP TAPE INPUT SETUP AUX INPUT SETUP NAME DVD2 NAME VCR PVR AUX DIGITAL IN COAX 2 DIGITAL IN OPTICAL 1 DIGITAL IN NONE DIGITAL IN OPTICAL 3 DIGITAL IN OPTICAL 5 DIGITAL IN OPTIC
57. L R inputs Pair 7 becomes the center C and subwoofer SUB inputs And Pair 8 becomes the surround left and right LS RS inputs Input types that are assigned to stereo analog input pairs 6 7 and 8 will be reassigned to the 5 1 channel analog input When selected for the Main Zone these input signals are sent to the corresponding outputs However neither Zone 2 nor the Record Zone provide multi channel outputs If the 5 1 channel analog input is selected for Zone 2 or the Record Zone only the front left and right L R inputs will be available 3 30 The SETUP Menu SDP 40 MAIN MENU SETUP gt DISPLAY SETUP gt ON SCREEN DISPLAY MODE ADJUST INPUTS ON SCREEN DISPLAY STATUS 2 SECONDS AUDIO CONTROLS SPEAKERS FRONT PANEL DISPLAY POSITION TOP REAR PANEL CONFIG AN SYNC DELAY OFF FORMAT NTSC CUSTOM NAME OFF BACKGROUND ON VOLUME CONTROLS EDIT CUSTOM NAME REMOTE STATE ON TRIGGERS LOCK OPTIONS DISPLAY SETUP ON SCREEN DISPLAY EE Default Parameter Value Values STATUS 2 SECONDS ALWAYS ON 2 SECONDS ALWAYS OFF POSITION TOP TOP CENTER BOTTOM FORMAT NTSC NTSC PAL SECAM BACKGROUND ON ON OFF REMOTE STATE ON ON OFF STATUS ALWAYS ON 2 SECONDS ALWAYS OFF STATUS activates and deactivates the on screen display provided the display device is utilizing the MAIN VIDEO OUTPUT labelled 1 OSD When set to ALWAYS ON the
58. N GUSTOM CENTER MIX 40dB SURROUND 008 2 BYPASS STATUS 5 1 BYPASS STATUS STATUS CNTR DLY SAMPLES 0 See page 5 17 for more MASTER LEVEL 0dB information about the INPUT see page 5 18 INPUT see page 5 19 NPUT see page 5 20 LFE MIX 40 0dB CUSTOM menu MODE 2CH BYPASS MODE 5 1 BYPASS MODE see page 5 20 SUB L R LVL 40dB INPUT TYPE BYP INPUT TYPE BYP CHANNELS see page 5 20 CUSTOM DECODE see page 5 20 L C R SL SR LFE SAMPLE RATE see page 5 20 5 1 BYPASS 8 58 L C R SL SR SB LFE OUTPUT LEVELS ELLLLEIE CUSTOM 2CH BYPASS NO PARAMETERS See pages 5 18 to 5 20 for more information about listening mode STATUS menus A 11 Appendix JBL INSTALLATION WORKSHEET INPUT SETUP DVD1 DVD2 LD TV SAT VCR CD PVR GAME TAPE TUNER AUX NAME DIGITAL IN ANALOG IN ANLG IN LVL VIDEO IN COMPONENT IN 2 CH DOLBY D dts ES Main Advanced INPUT SELECT ANALOG BYPASS SVIDEO 16 9 SVIDEO 4 3 OSD COMPONENT OSD Zone 2 Advanced INPUT SELECT Record Advanced INPUT SELECT ANLG IN LVL DIGITAL BYPASS DIG OUT RATE RECORD A 12 40 Appendix SPEAKER SETUP CUSTOM SETUP SYNTHESIS SETUP REAR PANEL CONFIG circle one TRIGGER SETUP FRONT L R 80Hz 8 STER
59. NE T 3 22 the SUB PARTY OFF 0 00B ter will MONO ON LFE SUB 40 0dB parameter wil appear as SUB LEFT DISPLAY SETUP MONO LOGIC ON When SUB L R is set to MONO SURROUND ON STEREO or NONE see page ON SCREEN DISPLAY 5 1 i FILM ON 3 22 the SUB MONO FRONT PANEL DISPLAY 5 115 TV ON parameter will appear as AN SYNC DELAY OFF 5 1 11 MUSIC ON SUB LEFT CUSTOM NAME OFF 5 1 THX SUR EX ON EDIT CUSTOM NAME DO DIGITAL ON 5 1 2 CHANNEL OFF Continued from page 5 5 1 MONO ON 5 1 MONO LOGIC ON 5 1 MONO SURR ON ON SCREEN DISPLAY FRONT PANEL DISPLAY Eres 121 FILM ON AAA 21 MUSIC ON STATUS 2 SECONDS STATUS ALWAYS ON umes THX ON POSITION TOP BRIGHTNESS 75 ON FORMAT NTSC ERTAS 2 CHAN BACKGROUND ON REMOTE STATE ON A 9 Appendix JBL 15 FILM DO PL Il Tax MONO LOGIC 5 172 MUSIC 5 1 MONO AUTO AZIMUTH ON RE EQUALIZER ON EFFECT LVL 948 VOCALENHANCE 0 0dB NO PARAMETERS MODE ADJUST VOCAL ENHANCE 0 0dB OUTPUT LEVELS ACADEMY FILTER ON 5SPKRENHANCE OFF RE EQUALIZER ON CUSTOM SURR ROLLOFF 3 1kHz BASS ENHANCE OFF 5 FILM SOUND STAGE REAR OUTPUT LEVELS RE EQUALIZER OFF 5 1 MONO LOGIC ly 5SPKRENHANCE OFF CUSTOM REAR DLY OFFSET 15ms MUSIC BASS ENHANCE _ EO PRO LOGIC II COMPRESSION OFF p
60. NLOCKED AUDIO CNTRL UNLOCKED LOCKED UNLOCKED SETUP UNLOCKED LOCKED UNLOCKED MODES LOCKED UNLOCKED MODES controls MODE ADJUST menu settings When set to LOCKED these settings cannot be adjusted with the exception of the SURROUND EX parameter on the 5 1 THX SURROUND EX or 5 1 THX menu This parameter setting can still be toggled by pressing the THX button on the remote control when the SHIFT command bank is active When set to UNLOCKED these settings can be adjusted AUDIO CNTRL LOCKED UNLOCKED AUDIO CNTRL controls AUDIO CONTROLS menu settings When set to LOCKED these settings cannot be adjusted When set to UNLOCKED these settings can be adjusted SETUP LOCKED UNLOCKED SETUP controls SETUP menu settings When set to LOCKED these settings cannot be adjusted with the exception of the STATUS parameters on the ON SCREEN DISPLAY and FRONT PANEL DISPLAY menus These parameters can still be set using the FP BLUE and OSD buttons on the remote control When set to UNLOCKED all SETUP menu settings can be adjusted 3 36 AUDIO CONTROLS Menu AUDIO CONTROLS esop 4 2 The AUDIO CONTROLS Menu JBL AUDIO CONTROLS AUDIO CONTROLS Selecting AUDIO CONTROLS on the MAIN MENU accesses the AUDIO CONTROLS BASS 0 00B menu which contains adjustable parameters TREBLE 0 00 TILT EQ 0 008 Use the up and down MENU arrows to scroll LOUDNESS on through the complete list Press the right BALANC
61. NO PVR 5 1 MONO LOGIC GAME dis L7 FILM 5 1 MONO SURR TAPE MAIN ADVANCED USE LAST TUNER ZONE2 ADVANCED AUX RECORD ADVANCED DVD1 is used as an example in this illustration and will continue to be used as an example throughout this section Whenever DVD1 appears as a step in a menu path any other input may be substituted MAIN MENU MODE ADJUST AUDIO CONTROLS SETUP SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGERS LOCK OPTIONS INPUT SETUP DVD2 LD TV SAT VCR CD PVR GAME TAPE TUNER AUX DVD1 is used as an example in this illustration and will continue to be used as an example throughout this section Whenever DVD1 appears as a step in a menu path any other input may be substituted DVD1 INPUT SETUP NAME DVD1 DIGITAL IN COAX 1 ANALOG IN NONE ANLG IN LVL AUTO VIDEO IN S VIDEO 1 COMPONENT IN 1 2 CH L7 FILM OO D 5 1 L7 FILM MAIN ADVANCED ZONE2 ADVANCED RECORD ADVANCED DVD1 EERE MODE ESES 14 FILM 7j MUSIC Eres THX fees 2 CHAN USE LAST The SETUP Menu MAIN MENU MODE ADJUST AUDIO CONTROLS may be substituted MAIN ADVANCED gt SETUP gt INPUT SETUP DVD1 INPUT SETUP gt DVD1 MAIN ADV NAME DVD1 INPUT SELECT
62. ODE ADJUST Menu JBL MODE ADJUST 121 FILM lai TV 121 MUSIC OO PL THx PRO LOGIC II PL II MUSIC PRO LOGIC 2 CHANNEL PARTY MONO MONO LOGIC MONO SURROUND 5 1 47 FILM 5 1 i TV 5 1 191 MUSIC 5 1 THX SUR EX DIGITAL 5 1 2 CHANNEL 5 1 MONO 5 1 MONO LOGIC 5 1 MONO SURR 127 FILM TEs 7 MUSIC THX s TAES 2 5 1 BYPASS 2CH BYPASS MODE ADJUST Selecting MODE ADJUST on the MAIN MENU accesses the MODE ADJUST menu which appears highlighting the name of the active listening mode Use the up and down MENU arrows to scroll through the complete list of listening modes Press the right MENU arrow to select the highlighted listening mode for configuration Press the left MENU arrow to return to the MAIN MENU All listening modes can be selected from the MODE ADJUST menu Selecting the desired listening mode accesses a menu containing specific options and parameters that can be adjusted to customize the selected mode These menus are pictured on pages A 10 and A 11 Other methods of listening mode selection are reviewed on pages 2 17 and 2 18 LISTENING MODE DESCRIPTIONS LOGIC7 FILM MODE ADJUST e e A proprietary Lexicon listening mode e Designed for playback of 2 channel stereo or matrix encoded stereo film sources e Derives seven channels from 2 channel input types e Derives full frequency stereo surrounds realistic
63. OUTPUTS TO A REAR L R 80Hz D SYNTHESIS 7CH SPEAKER SUB L R MONO x gt CONFIGURATION SUB XOVER 80Hz 0 5 LFE OFF Da G e Default Parameter Value Values FRONT L R 80Hz 80Hz CENTER 80Hz 80Hz SIDE L R 80Hz 80Hz REAR L R 80Hz 80Hz NONE SUB L R MONO MONO SUB XOVER 80Hz 80Hz LFE OFF OFF The SYNTHESIS 7 SETUP menu can be used to configure the MAIN AUDIO OUTPUTS for a 5 1 or 7 1 channel Synthesis system which incorporates THX certified loud speakers For a non THX certified speaker system use the CUSTOM SETUP menu see page 3 18 When SYNTHESIS 7CH SETUP is selected a message will appear cautioning that if the right MENU arrow is pressed again the MAIN AUDIO OUTPUTS will automatically change to a SYNTHESIS 7CH speaker configuration This will override custom speaker settings that have been chosen Press the right MENU arrow to activate a SYNTHESIS 7CH speaker configuration Press the left MENU arrow to cancel SYNTHESIS 7 speaker configuration and return to the SPEAKER SETUP menu If a SYNTHESIS 7CH speaker configuration is activated the SYNTHESIS 7CH SETUP menu will display the SYNTHESIS 7 configuration settings The unit will automatically set all outputs to 80Hz with a 24dB per octave filter The only exceptions are SUB L R and LFE SUB L R will be set to MONO see page 3 22 and LFE will be set to OFF see page 3 23 SYNTHESIS 7CH speaker configuration applies to all inputs a
64. PUT SETUP menu If USE LAST is selected in the INPUT SETUP menu when the input format changes the unit will revert to the listening mode that was last used for the input type 2 16 40 Basic Operation MODE FAMILY SELECTION BUTTONS This type of mode selection occurs each time one of the Mode Family Selection buttons is pressed on the remote control The matrix below shows how this type of mode selection determines the listening mode e input is selected using the input selection buttons on the front panel or remote control Note Mode Family Selection will be overridden under the following conditions e The Mode Up and Down buttons on the front nel or the MODE buttons on the remote 2 CHANNEL DIGITAL dts ES pane E control are pressed Type DOLBY PRO 5 1 THX dts ES THX e listening mode for the current input type is LOGIC Il THX SURROUND changed in the INPUT SETUP menu DOLBY PRO DOLBY INPUT SETUP LOGIC 11 DIGITAL Menu O LOGIC7 5 1 LOGIC7 dts ES LOGIC7 FILM FILM FILM LOGIC7 TV 5 1 LOGIC7 INPUT SETUP TV Menu INPUT SETUP INPUT SETUP dts ES Menu Menu LOGIC7 5 1 LOGIC7 dts ES LOGIC7 MUSIC MUSIC MUSIC Reverts to the mode selected in the designated parameter on the INPUT SETUP menu 3 SETUP Menu Sir AS 3 2 INPUT SETUP es ots ts epa Et eive te MD 3 3 SPEAKER SETUP cas dei loves
65. PUT TYPE BYP An alphabetical listing of parameter descriptions begins on page 5 20 5 18 40 The MODE ADJUST Menu DOLBY DIGITAL STATUS MENU The DOLBY DIGITAL STATUS menu will appear when a Dolby Digital listening mode is selected It features L C R SL SR and LFE level meters see page 5 18 for more information Parameter Values CHANNELS 3 2 1 3 2 3 1 2 2 2 1 2 0 1 0 ENCODING MATRIX NONE SAMPLE RATE 48kHz REF OFFSET 4dB An alphabetical listing of parameter descriptions begins on page 5 20 5 1 BYPASS STATUS MENU The 5 1 BYPASS STATUS menu will appear when the 5 1 BYPASS listening mode is selected It features L C R SL SR and LFE level meters see page 5 18 for more information Parameter Values INPUT The name of the selected input MODE 5 1 BYPASS INPUT TYPE BYP An alphabetical listing of parameter descriptions begins on page 5 20 5 1 ANALOG STATUS MENU The 5 1 ANALOG STATUS menu features L C R SL SR and LFE level meters see page 5 18 for more information It will appear when all of the following conditions are met e 5 STEREO amp 5 1 ANLG is selected on the REAR PANEL CONFIG menu see page 3 30 ANALOG IN parameter on the INPUT SETUP menu is set to 5 1 ANALOG see page 3 6 e The INPUT SELECT parameter the MAIN ADV menu is set to either AUTO or ANALOG see page 3 13 When set to AUTO no digital input types can be pres
66. R outputs Performance Zone 2 and Record Zone Analog to Digital Conversion 24 bit 44 1 to 96kHz dual bit architecture Record Zone only Digital to Analog Conversion Frequency Response 24 bit 44 1 to 192kHz multi bit AY architecture 10Hz to 20kHz 0 1dB 0 25dB 0 75dB at 40kHz reference 1kHz THD Noise Below 0 00896 at 1kHz maximum output level Dynamic Range 105dB minimum 108dB typical 22kHz bandwidth Signal to Noise Ratio 105dB minimum 108dB typical 22kHz bandwidth Input Sensitivity 200mVrms 4Vrms for maximum output level Input Impedance 100kQ in parallel with 150pF Output Level 200mVrms typical 4Vrms maximum RCA outputs 400mVrms typical 8Vrms maximum XLR outputs Zone 2 only maximum value with full scale input signal and volume at OdB Output Impedance 1000 in parallel with 150pF RCA outputs 500 in parallel with 150pF XLR outputs Zone 2 only 40 Appendix Video Inputs and Outputs Video Inputs 5 composite RCA 8 S video and 4 component video 3 RCA 1 BNC Video Outputs 4 composite RCA 2 monitor and 2 record 4 S video 2 monitor and 2 record and 1 component BNC Performance Composite amp S video NTSC M PAL and SECAM compatible Switching Active Output Level 1 0V peak to peak Impedance 750 Input Return Loss
67. RIGHT 0 00B DISPLAYS SIDE RIGHT 40 0dB VOLUME CONTROLS Q Pe REAR RIGHT 40 0dB TRIGGERS Mon REAR LEFT 40 0dB LOCK OPTIONS 11 o SIDE LEFT 40 0dB a SUB MONO 40 0dB Ds SUB RIGHT 40 0dB Lic EN e A LFE SUB 40 0dB Note Front panel and remote control buttons except the MENU button and MENU arrows will not function while the SPEAKER LEVEL ADJUST menu is selected All buttons will regain functionality when the menu is exited LEVELS CALIBRATION Ez o Properly calibrated output levels are critical Setting output levels is a simple procedure using a Sound Pressure Level SPL meter This device measures the relative loudness of the speakers so that output levels can be calibrated accurately An SPL meter can be purchased at Radio Shack catalog no 33 2050 To ensure the most accurate calibration levels e Eliminate extraneous noises in the listening space such as conversation air conditioners and sounds that filter in from open doors and windows e Remove objects including people that obstruct the line of sight path between the SPL meter and the speaker being measured When SUB L R is set to STEREO or NONE see page 3 22 the SUB parameter will appear as SUB LEFT e Measure output levels from the primary listening position placing the SPL meter at the approximate spot where the listener s head will be during listening INTERNAL NOISE TEST
68. S 225522 5 17 CUSTOM fheia Ee Aes 5 17 STATUS MeNUS i s ne IE We RR eL x 5 18 Mode Parameter Descriptions 5 20 Section 6 Troubleshooting and Maintenance Troubleshooting 6 2 Restoring Factory Default Settings 6 4 Maintenance 0304 3 Eyed LE ES 6 4 Appendix Specifications eC Lot y iE Leo nates A 2 Declaration of Conformity 4 Men Tree Pe pues REY TV A 5 Installation Worksheet A 12 Index Introduction JBL ENGLISH IMPORTANT SAFETY INSTRUCTIONS Save these instructions for later use Follow all instructions and warnings marked on the unit Always use with the correct line voltage Refer to the manufacturer s operating instructions for the power requirements Be advised that different operating voltages require the use of a different line cord and or attachment plug Do not install this unit in an unventilated rack nor directly above items that generate heat such as power amplifiers Observe the maximum ambient operating temperature listed in the product specification The openings on the case are provided for ventilation to ensure reliable operation and prevent it from overheating these openings must not be blocked or covered Never push ob
69. S 8 STEREO INPUTS AUDIO CONTROLS SPEAKERS OR 5 STEREO amp 5 1 ANLG DISPLAYS VOLUME CONTROLS TRIGGERS LOCK OPTIONS REAR PANEL CONFIG The REAR PANEL CONFIG menu can be used to configure AUDIO INPUT pairs 1 to 8 on the rear panel These inputs can be set up to function as eight stereo analog input pairs or as five stereo analog input pairs and one 5 1 channel analog input 8 STEREO INPUTS SETUP gt REAR PANEL CONFIG 8 STEREO INPUTS 8 STEREO INPUTS is the default setting for REAR PANEL CONFIG When set to 8 STEREO INPUTS the AUDIO INPUTS are configured as eight stereo analog input pairs Pairs 6 7 and 8 are not available as a 5 1 channel analog input Input types that are assigned to the 5 1 channel analog input will be reassigned to stereo input Pair 6 e ANALOG IN parameter on the INPUT SETUP menu is set to 5 1 ANALOG see page 3 6 e INPUT SELECT parameter on the MAIN ADV menu is set to either AUTO or ANALOG see page 3 13 When set to AUTO no digital input types can be present e ANALOG BYPASS parameter on the MAIN ADV menu is set to ON see page 3 13 5 STEREO amp 5 1 ANLG SETUP gt REAR PANEL CONFIG gt 5 STEREO amp 5 1 ANLG When set to 5 STEREO amp 5 1 ANLG the AUDIO INPUTS are configured as five stereo analog input pairs and one 5 1 channel analog input The 5 1 channel analog input consists of AUDIO INPUT pairs 6 7 and 8 Pair 6 becomes the front left and right
70. SAT VIDEO IN S VIDEO 1 L C R SL SR TRIGGERS VCR COMPONENT IN 1 LOCK OPTIONS CD 2 CH L7 FILM LLLE PVR oa D 5 1 L7 FILM GAME TAES dts L7 FILM TAPE MAIN ADVANCED TUNER ZONE2 ADVANCED AUX RECORD ADVANCED DVD1 is used as an example in this illustration and will continue to be used as an example throughout this section Whenever DVD1 appears as a step in a menu path any other input may be substituted levels When the signal is too high ANLG IN LVL is quickly decreased to avoid overload When the signal is too low ANLG IN LVL is slowly increased to maximize the signal to noise ratio and dynamic range The AUTO parameter setting will never exceed the current MANUAL parameter setting The current AUTO parameter setting is shown in the INPUT GAIN parameter When the AUTO parameter is set to OFF the ANLG IN LVL parameter can be adjusted manually MANUAL 18 to 12dB MANUAL provides manual adjustment of analog input levels in the Main Zone when the AUTO parameter is set to OFF When MANUAL is selected a white horizontal bar graph will appear on the screen below the parameter This graph illustrates the position at which the current setting falls within the 18 to 12dB parameter range Press the up and down MENU arrows to increase and decrease the setting in 1dB increments Press the left MENU arrow to close the graph and return to the ANLG IN LVL menu The current setting is shown in the MANUAL and INPUT GAIN pa
71. SYNTHESIS SDP 40 DIGITAL SURROUND PROCESSOR CONTROLLER USER GUIDE IMPORTANT SAFETY INSTRUCTIONS 11 12 13 14 DOE SION Oei Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with dry cloth Do not block any ventilation openings Install in accordance with the manufacturer s instructions Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus Only use attachments accessories specified by the manufacturer Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avoid injury from tip over Unplug this apparatus during lightning storms or when unused for long peri
72. Selecting either INTERNAL NOISE TEST or DACS CALIBRATION accesses the SPEAKER LEVEL ADJUST menu INTERNAL NOISE pictured above When INTERNAL NOISE WU TEST is selected a cautionary message HIGH AUDIO LEVELS pictured at the right will appear on the screen This serves as a reminder that the INTERNAL NOISE TEST generates loud calibration noises When the message appears press the right MENU arrow to proceed to the SPEAKER LEVEL ADJUST menu Press the left MENU arrow to return to the LEVELS CALIBRATION menu As the INTERNAL NOISE TEST is conducted a noise signal will move from output to output following the order on the SPEAKER 3 26 40 The SETUP Menu LEVEL ADJUST menu The cursor will automatically scroll through the menu highlighting each output as it is tested Each output is tested for approximately 4s It is possible to manually select a speaker just as the unit is about to automatically scroll to the next speaker causing the unit to send the noise signal to both outputs If this occurs reselect the desired speaker The calibration noise will pass briefly through the SUB R output when the SUB L R parameter on the CUSTOM SETUP or SYNTHESIS 7CH SETUP menu is set to MONO or the SUB RIGHT parameter on the SPEAKER LEVELS ADJUST menu is manually selected during the test Before making adjustments set the SPL meter to C weighting and SLOW response Use the up and down MENU arrows to temporarily
73. TOM appears when the modified version of the listening mode is selected and the message PRESET appears when the factory default version of the listening mode is selected Press the left MENU arrow to close the CUSTOM VS PRESET pulldown menu RESET MODE RESET MODE restores the selected listening mode to its factory default condition Selecting this option accesses the pulldown CUSTOM VS PRESET menu pictured at the right Press the right MENU arrow to restore the factory default version of the selected listening mode Press the left MENU arrow to exit the RESET MODE pulldown menu without restoring the selected listening mode to its factory default settings CUSTOM 5 17 The MODE ADJUST Menu JBL STATUS MENUS then Unlike other menus the listening mode STATUS menu can only be accessed with the above remote control command sequence Press the SHIFT button then the STAT button to check the STATUS of the active listening mode at any time Press the STAT button again to exit the menu Use the MENU arrows for front panel display viewing of STATUS menu parameters STATUS menu parameters provide current information about the active input and the unit and cannot be adjusted These parameters will vary depending on whether a 2 channel Dolby Digital or dts ES input type is present 5 1 BYPASS and 2CH BYPASS input types have individual STATUS menus Additionally the 5 1 ANALOG STATUS menu will appear when certa
74. TRIGGERS SUB XOVER 80Hz 70Hz 40Hz LOCK OPTIONS LFE OFF 80Hz 50Hz THX 80Hz 60Hz Sod 90Hz 70Hz D 100Hz 80Hz 110Hz THX 80Hz 120Hz 90Hz 100Hz 110Hz 120Hz NONE CUSTOM SETUP continued e Ez 9 EEUE FRONT L R FULL 30Hz to 120Hz THX 80Hz The FRONT L R parameter sets the crossover setting for the MAIN AUDIO OUTPUTS labelled FRONT L R When set to FULL the unit sends a full range audio signal to the FRONT L R outputs When set to a numerical crossover setting the unit activates a crossover at the selected frequency Choose the setting closest to the low frequency rating of the front left and right speakers See pages 3 18 and 3 19 for more information about crossover settings CENTER FULL 30Hz to 120Hz THX 80Hz NONE The CENTER parameter sets the crossover setting for the MAIN AUDIO OUTPUT labelled CENTER When set to FULL the unit sends a full range audio signal to the CENTER output When set to a numerical crossover setting the unit activates a crossover at the selected frequency Choose the setting closest to the low frequency rating of the center speaker See pages 3 18 and 3 19 for more information about crossover settings When set to NONE the unit redirects center channel signals to the FRONT L R outputs 3 20 The SETUP Menu SDP 40 MAIN MENU gt SETUP gt SPEAK
75. TROLS menu 3 0 to 3 0dB EQ affects the entire frequency spectrum with a hinge point at 1 2 As it is increased frequencies above 1kHz boosted while frequencies below 1kHz are simultaneously cut As it is decreased frequencies above 1kHz are cut while frequencies below 1kHz are simultaneously boosted The graph pictured below shows the frequency response of all TILT EQ settings 3 0 28 2 6 24 22 20 1 8 16 1 4 12 1 0 0 8 0 6 0 4 0 2 0 0 0 2 40 4 40 6 40 8 410 412 14 416 418 20 22 24 26 28 3 0 100 200 500 Hz 1k 2k 5k 3 0 28 26 24 22 42 0 18 16 14 12 10 08 06 404 40 2 40 0 02 04 06 08 10 14 16 18 20 22 2 4 2 6 28 3 0 10k 20k 4 3 The AUDIO CONTROLS Menu JBL LOUDNESS AUDIO CONTROLS gt LOUDNESS LOUDNESS controls the amount of low frequency boost that is automatically applied to the FRONT L R CENTER SUBWOOFER L R and LFE outputs When set to ON loudness compensation is automatically applied based on the current volume level As volume is decreased the amount of boost is automatically increased The loudness contour is optimized for sources calibrated to Dolby reference levels When set to OFF loudness compensation is not applied ON OFF The graph pictured below shows the frequency response that is automatically applied when Main Zone vo
76. V menu which can be used to configure advanced settings in the Record Zone Default Parameter Value Values INPUT SELECT DIGITAL AUTO ANALOG DIGITAL ANLG IN LVL 0dB 18 to 12dB DIGITAL BYPASS OFF ON OFF DIG OUT RATE 44 1kHz 44 1kHz 48kHz 88 2kHz 96kHz INPUT RECORD ENABLED ENABLED BLOCKED The INPUT SETUP menu allows the selection of two audio connector types one analog one digital INPUT SELECT specifies how these connectors interact The following settings are available e The DIGITAL setting forces the unit to utilize the DIGITAL IN connector for the Record Zone If an ANALOG IN connector is also selected it will be ignored The unit will mute when an invalid digital audio input type is received Valid digital audio input types include PCM Dolby Digital and dts ES See page 2 16 for more information about using the DIGITAL setting in multiple zones e The ANALOG setting forces the unit to utilize the selected ANALOG IN connector for the Record Zone If a DIGITAL IN connector is also selected it will be ignored 3 16 40 The SETUP Menu e The AUTO setting allows the unit to switch between the selected DIGITAL IN and ANALOG IN connectors The DIGITAL IN connector is utilized when a valid digital audio input type is present When invalid digital audio input types are received the unit automatically switches to the ANALOG IN connector INPUT SELECT will automatically be set to AUTO when
77. V menu is automatically set to ANALOG see page 3 13 When a connector is selected for both the DIGITAL IN and ANALOG parameters all INPUT SELECT parameters will automatically be set to AUTO The INPUT SELECT parameters are located on the MAIN ADV ZONE 2 ADV and REC ADV menus see pages to 3 5 The SETUP Menu JBL MAIN MENU gt SETUP gt INPUT SETUP gt DVD1 INPUT SETUP gt DVD1 ANALOG IN MODE ADJUST NAME DVD1 ANALOG 1 AUDIO CONTROLS SPEAKERS DVD2 DIGITAL IN COAX 1 ANALOG 2 REAR PANEL CONFIG LD ANALOG 3 DISPLAYS TV ANLG IN LVL AUTO ANALOG 4 VOLUME CONTROLS SAT VIDEO IN S VIDEO 1 ANALOG 5 TRIGGERS VCR COMPONENT IN 1 ANALOG 6 LOCK OPTIONS CD 2 CH L7 FILM ANALOG 7 PVR DO D 5 1 L7 FILM ANALOG 8 GAME TAES dts L7 FILM NONE TAPE MAIN ADVANCED TUNER ZONE ADVANCED When REAR PANEL CONFIG AUX RECORD ADVANCED is set to 5 STEREO amp 5 1 ANLG see page 3 30 5 1 DVD1 is used as an example in this illustration and will continue to be used as an example A pts throughout this section Whenever DVD1 appears as a step in a menu path any other input may be substituted ANALOG IN ANLG IN LVL EI Selecting ANALOG IN accesses the ANALOG IN menu which be used to assign the analog input connector for the selected input The appearance of the ANALOG IN menu depends on the REAR PANEL CON
78. Y 11797 800 336 4JBL Part 070 14991 Rev 10 01
79. ack of stereo sources e Sends stereo sources to all channels e Recommended for background music Default Parameter Values Default Value OUTPUT LEVELS See page 5 17 for more information CUSTOM See page 5 17 for more information An alphabetical listing of parameter descriptions begins on page 5 20 40 The MODE ADJUST Menu MONO IMODEADIUST O MONO e Designed for playback of mono sources e Sends mono sources to the center channel only Default Parameter Value Values SUB L R 0dB OFF 30 to 12dB An alphabetical listing of parameter descriptions begins on page 5 20 MONO LOGIC AAA gt MN Designed for playback of mono sources e Utilizes proprietary Lexicon reverb technology to realistically expand mono input types to utilize all channels dramatically increasing the perceived length and sense of envelopment of the listening space Default Parameter Value Values EFFECT LVL 9dB 12 to 6dB ACADEMY FILTER ON ON OFF SURR ROLLOFF 3 1kHz 500Hz to 20 0kHz OFF OUTPUT LEVELS CUSTOM See page 5 17 for more information See page 5 17 for more information An alphabetical listing of parameter descriptions begins on page 5 20 5 7 The MODE ADJUST Menu JBL MONO SURROUND MODE ADJUST gt MONO SURROUND e Designed for playback of mono sources e Sends mono sources to all channels Default Parameter Values Default Value OUTPUT LEVELS S
80. adjusts the relative level of the surround channels that are encoded into the FRONT L R outputs The recommended setting is 2 to 3dB for all input types VOCAL ENHANCE 0 0dB 3 0dB 6 0dB VOCAL ENHANCE adjusts the level of dialog boost in the CENTER output Increasing this level is recommended for listening at lower volume levels or for increasing dialog intelligibility 5 24 eshooting and Maintenance E E 6 2 Restoring Factory Default Settings 6 4 Routine Maintenance 6 4 Troubleshooting and Maintenance JBL TROUBLESHOOTING Note e SDP 40 does not support MPEG input types e Some DVD players will produce audio artifacts when switching audio formats THE UNIT DOES NOT POWER ON 1 Attempt to power the unit on with both amp standby buttons the one on the front panel and the one on the remote control Check the line cord to ensure a good connection between the electrical outlet and the AC input connector Make sure the rear panel power switch is set to on See pages 2 4 and 2 7 for rear panel illustrations THE REMOTE CONTROL DOESN T WORK 1 Make sure the front panel IR Receiver window is not obstructed see pages 2 2 and 2 6 for illustrations remote control must be in l
81. air you will be charged for the repairs or the examination Although you must pay any shipping charges incurred in getting your JBL product to an Authorized Warranty Station or to the factory we will pay return shipping charges within the United States if the repairs are covered by the warranty Please be sure to save the original shipping cartons because a nominal charge will be made for additional cartons Limitation on implied warranties Implied warranties of merchantability and fitness for particular purpose are limited in duration to the length of this warranty unless otherwise provided by state law Exclusion of certain damages JBL s liability is limited to the repair or replacement at our option of any defective product and shall in no event include incidental or consequential commercial damages of any kind Some states do not allow limitations on how long an implied warranty lasts and or do not allow the exclusion of incidental or consequential damages so they above limitations and exclusions may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state We sincerely thank you for your expression of confidence in JBL products This equipment has been painstakingly assembled by highly trained craftspeople It should give you many years of musical enjoyment JBL Synthesis 8500 Balboa Boulevard Northridge CA 91329 250 Crossways Park Drive Woodbury N
82. ally increasing the perceived width of the listening space With side and rear speakers selected LOGIC7 FILM also increases the perceived length and sense of envelopment of the listening space e Provides remarkable improvement compared to other decoders e Recommended for 2 channel film sources even when only one pair of surround speakers is selected Default Parameter Value Values AUTO AZIMUTH ON ON OFF VOCAL ENHANCE 0 0dB 0 0dB 3 0 6 0dB RE EQUALIZER ON ON OFF SOUND STAGE REAR FRONT NEUTRAL REAR 5 SPKR ENHANCE OFF ON OFF BASS ENHANCE OFF ON OFF SURR ROLLOFF 15 3kHz 500Hz to 20 0kHz OFF REAR DLY OFFSET 15ms 0 to 30ms OUTPUT LEVELS See page 5 17 for more information CUSTOM See page 5 17 for more information An alphabetical listing of parameter descriptions begins on page 5 20 40 The MODE ADJUST Menu LOGIC7 TV gt w A proprietary Lexicon listening mode Designed for playback of 2 channel stereo or matrix encoded stereo TV sources Based on LOGIC7 FILM but specifically tailored for TV sources Recommended for 2 channel TV sources even when only one pair of surround speakers is selected LOGIC7 MUSIC ADJUST gt Iz MUSIC A proprietary Lexicon listening mode Designed for playback of 2 channel stereo or matrix encoded stereo music sources Based on LOGIC7 FILM but specifically tailored for music sources
83. ameter to OFF will automatically deactivate the on screen display if the display device is utilizing the COMPONENT VIDEO OUTPUT REMOTE STATE ON OFF The REMOTE STATE parameter controls whether or not the active remote control command bank will be indicated on the on screen display When set to ON the active command bank is indicated in the top right corner of the on screen display A yellow Z will appear when the ZONE command bank is active A red R will appear when the REC command bank is active A blue S will appear when the SHIFT command bank is active Nothing will appear when the MAIN command bank is active When set to OFF the active command bank is not indicated on the on screen display STATUS activates and deactivates the front panel display When set to ALWAYS ON the front panel display remains on at all times When set to 2 SECONDS the front panel display will appear for two seconds when the unit receives a command or the input type changes When set to ALWAYS OFF the front panel display remains off at all times BRIGHTNESS 100 75 50 25 BRIGHTNESS adjusts the brightness of the front panel display The front panel display will adjust accordingly when a setting is selected A V SYNC DELAY O EA 9 MENEN A V SYNC DELAY synchronizes the delay DISPLAY SETUP time between audio and video signals This parameter is useful when using a video FRONT PANEL DISPLAY processor or lin
84. as a step in a menu path any other input may be substituted COMPONENT IN 6 Selecting COMPONENT IN accesses the COMPONENT IN menu which can be used to select the component video connectors associated with the selected input Note The component video output is only available when component video inputs are used The SETUP Menu JBL MAIN MENU MODE ADJUST AUDIO CONTROLS SETUP SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGERS LOCK OPTIONS DVD1 is used as an example in this illustration and will continue to be used as an example throughout this section Whenever DVD1 appears as a step in a menu path any other input may be substituted 2 CH EX EX Selecting 2 CH accesses the 2 CH MODE menu pictured above which can be used to select the listening mode for 2 channel input types Listening modes are explained in further detail in Section 5 INPUT SETUP DVD1 INPUT SETUP NAME DVD1 DVD2 DIGITAL IN COAX 1 LD ANALOG IN NONE TV ANLG IN LVL AUTO SAT VIDEO IN S VIDEO 1 VCR COMPONENT IN 1 CD PVR Da D 5 1 L7 FILM GAME dts dts L7 FILM TAPE MAIN ADVANCED TUNER ZONE2 ADVANCED AUX RECORD ADVANCED DOLBY D DVD1 2 CH MODE 121 FILM 121 TV 121 MUSIC PL Tax PRO LOGIC II PL Il MUSIC PRO LOGIC 2 CHANNEL PARTY MONO MONO
85. atio of the incoming signal When set to OFF the on screen display utilizing the S video output is displayed in the same aspect ratio as the incoming signal COMPONENT OSD activates and deactivates the on screen display provided the display device is utilizing the COMPONENT VIDEO OUTPUT When set to ON the COMPONENT VIDEO OUTPUT displays the on screen menus as a 480i video signal on a full blue screen background The component on screen display includes the two line status When set to OFF the component on screen display is deactivated The component on screen display will be automatically deactivated when the BACKGROUND parameter on the ON SCREEN DISPLAY menu is set to OFF see page 3 32 ZONE2 ADVANCED Eug o EX Selecting ZONE2 ADVANCED accesses the ZONE 2 ADV menu which can be used to configure advanced settings in Zone 2 Default Parameter Value Values INPUT SELECT DIGITAL AUTO ANALOG DIGITAL 3 14 40 The SETUP Menu MAIN MENU gt SETUP gt INPUT SETUP gt DVD1 INPUT SETUP gt DVD1 ZONE 2 ADV MODE ADJUST NAME DVD1 INPUT SELECT DIGITAL AUDIO CONTROLS SPEAKERS DVD2 DIGITAL IN COAX 1 REAR PANEL CONFIG LD ANALOG IN NONE DISPLAYS TV ANLG IN LVL AUTO VOLUME CONTROLS SAT VIDEO IN S VIDEO 1 TRIGGERS VCR COMPONENT IN 1 LOCK OPTIONS CD 2 CH L7 FILM PVR DO D 5 1 L7 FILM GAME TAES dts L7 FILM TAPE MAIN ADVANCED TUNER AUX RECORD ADVANCED
86. ce is present LFE OFF 30 to 12dB LFE Low frequency Effects adjusts the output level of the LFE out put 5 22 40 The MODE ADJUST Menu LFE MIX 20 0 or 10 0 to 0 0dB LFE MIX adjusts the level of the LFE channel the 1 channel in a 5 1 or 6 1 channel source that is sent to the SUBWOOFER L R outputs Low frequencies from as many as five other channels may be combined with the LFE channel to create the SUBWOOFER L R output signal significantly raising subwoofer output levels Careful adjustment of this parameter allows achievement of proper tonal balance and reduces the risk of subwoofer overload MASTER LEVEL 5 5dB MASTER LEVEL adjusts the output level of LOGIC7 encoded 2 channel signals MODE MODE MODE indicates the name of the selected listening mode OUTPUT LEVELS See page 5 17 for information about OUTPUT LEVELS PANORAMA ON OFF When set to ON PANORAMA extends the front stereo image to include the surround speakers for a wraparound effect with side wall imaging RE EQUALIZER ON OFF RE EQUALIZER simulates the high frequency rolloff that occurs in a movie theater as sound travels from speakers to the listeners When set to ON the unit applies a high frequency rolloff When set to OFF the unit does not apply a high frequency rolloff Most films are mixed for movie theaters and may sound too bright when played back in home theaters without re equalization RE EQUALIZ
87. contains options and parameters to adjust the on screen and front panel displays as well as audio video synchronization and the customized unit name See page 3 31 for more information VOLUME CONTROLS SETUP VOLUME CONTROLS Selecting VOLUME CONTROLS accesses the VOLUME CONTROL SETUP menu which contains parameters for adjusting volume setup in the Main Zone Zone 2 and the Record Zone See page 3 34 for more information TRIGGERS E373 Selecting TRIGGERS accesses the TRIGGER SETUP menu which contains parameters for configuring TRIGGERS 1 and 2 See page 3 35 for more information LOCK OPTIONS 5 Selecting LOCK OPTIONS accesses the LOCK OPTIONS menu which contains parameters for locking and unlocking the MODE ADJUST AUDIO CONTROLS and SETUP menus See page 3 36 for more information The SETUP Menu SDP 40 MAIN MENU gt SETUP gt INPUT SETUP DVD1 INPUT SETUP MODE ADJUST NAME DVD1 AUDIO CONTROLS SPEAKERS DVD2 DIGITAL IN COAX 1 REAR PANEL CONFIG LD ANALOG IN NONE DISPLAYS TV ANLG IN LVL AUTO VOLUME CONTROLS SAT VIDEO IN S VIDEO 1 TRIGGERS VCR COMPONENT IN 1 LOCK OPTIONS CD 2 CH L7 FILM PVR DO D 5 1 L7 FILM GAME TAES dts L7 FILM TAPE MAIN ADVANCED TUNER ZONE2 ADVANCED AUX RECORD ADVANCED DVD1 is used as an example in this illustration and will continue to be used as an example throughout this section Whenever DVD1 appear
88. der falls sich seine Arbeitsweise derart ndert da daraus ein Bedarf nach Raparatur zu schlie en ist Dieser Apparat sollte nur von qualifizierten Fachleuten ge ffnet werden Das Abnehmen von Abdeckungen setzt Sie gef hrlichen Spannungen aus A A Dieses Dreieck auf Ihrem Apparat warnt Sie vor nicht isolierter gef hrlicher Spannung im Geh use stark genug um eine Ber hrungsgefahr darzustellen Dieses Dreieck auf Ihrem Apparat bedeutet da wichtige Betriebs und Wartungsanweisungen in der mitgelieferten Dokumentation zu finden sind ESPANOL INSTRUCCIONES IMPORTANTES DE SEGURIDAD Guarde esta instrucciones para uso posterior A Utilice siempre el voltaje correcto Dir jase a las instrucciones de operaci n del fabricante para obtener las especificaciones de potencia Est al tanto de que voltajes de operaci n distintos requieren el uso de cables y o enchufes distintos No instale esta unidad en un estante sin ventilaci n ni tampoco directamente encima de equipos que generen calor tales como amplificadores de potencia F jese en las temperaturas ambientales m ximas de operaci n que se mencionan en las especificaciones del producto Las aperturas y ranuras del chasis sirven para proveer la ventilaci n necesaria para operar la unidad con seguridad y para prevenir sobrecalentamiento y por lo tanto no pueden ser obstruidas o cubiertas No introduzca objetos de ning n tipo a trav s de las ranuras
89. e practice condition or the like that if not correctly performed or adhered to could result in damage to or destruction of part or all of the product Note Calls attention to information that is essential to highlight 9 9 NAME Represents a menu path steps in grey boxes illustrate a series of selections that must be made to reach the destination in the black box In the example above the SETUP INPUTS and DVD1 options must be selected to reach the NAME menu LOCATION CONSIDERATIONS The unit requires special care during installation to ensure optimal performance The unit should be installed on a shelf or in a standard 19 equipment rack using the enclosed optional rack mount kit CAUTION Observe the following precautions when installing the unit e Select a dry well ventilated location out of direct sunlight e Do not stack the unit directly above heat producing equipment such as power amplifiers e Avoid placing the unit near unshielded or FM antennas cable TV decoders and other RF emitting devices If placed in close proximity to the unit these devices may cause interference Do not obstruct the front panel IR Receiver window see pages 2 2 and 2 6 for illustrations The remote control must be in line of sight with the receiver for proper operation If line of sight is impractical an infrared remote system can be used with the rear panel IR IN connector The unit can be placed inside a
90. e CUSTOM SETUP menuis set to NONE see page 3 20 40 Troubleshooting and Maintenance A HUMMING SOUND IS PRESENT IN THE AUDIO 1 Disconnect the cable television connector if present from the wall outlet If this eliminates the humming sound an isolation device is required Contact the cable provider for assistance Disconnect source components to isolate the problem Once the problematic component is identified make sure it is properly grounded and connected to the same electrical circuit as the SDP 40 RF INTERFERENCE IS PRESENT IN THE AUDIO OR VIDEO 1 2 3 Move antennas away from the unit Move RF emitting devices away from the unit Replace unshielded cables with shielded cables wherever possible THE UNIT IS EXHIBITING ERRATIC BEHAVIOR 1 Power the rear panel power switch off Wait 10 seconds Power the rear panel power switch on See pages 2 4 and 2 7 for rear panel illustrations Document all user defined settings on the installation worksheet see page A 12 Restore factory default settings see pages 1 5 or 6 4 IF ALL ELSE FAILS 1 Power the rear panel power switch off Wait 10 seconds Power the rear panel power switch on See pages 2 4 and 2 7 for rear panel illustrations Document all user defined settings on the installation worksheet see pages A 12 Restore factory default settings see pages 1 5 or 6 4 Contact an authorized JBL Synthesis dealer Contact J
91. e of the ZONE2 AUDIO OUTPUTS When ZONE2 BALANCE is selected a horizontal graph pictured on page 4 2 will appear on the screen below the parameter This graph illustrates the position at which the current setting falls within the entire parameter range Press the up MENU arrow to move the setting toward the right and the down MENU arrow to move the setting toward the left Press the left MENU arrow to close the graph and return to the AUDIO CONTROLS menu 40 The AUDIO CONTROLS Menu RECORD BALANCE AUDIO CONTROLS gt RECORD BALANCE RECORD BALANCE controls the left to right balance of the RECORD AUDIO OUTPUTS When RECORD BALANCE is selected a horizontal graph pictured on page 4 2 will appear on the screen below the parameter This graph illustrates the position at which the current setting falls within the entire parameter range Press the up MENU arrow to move the setting toward the right and the down MENU arrow to move the setting toward the left Press the left MENU arrow to close the graph and return to the AUDIO CONTROLS menu 5 The MODE ADJUST Menu MO DIE AD US Posicion sett EM deed pons caesar 5 2 Listening Mode Descriptions uie et x te ten pto Ret IRR 5 2 OUTPUT 5 17 CUSTOM EE 5 17 S TATUS MENUS tub ts pa pc ta o niue dus 5 18 Mode Parameter 5 20 The M
92. e scaler These products OFF introduce a delay in the video signal which causes the audio and video signals to EDIT CUSTOM NAME 3 32 The SETUP Menu SDP 40 MAIN MENU gt SETUP DISPLAY SETUP FRONT PANEL DISPLAY MODE ADJUST INPUTS ON SCREEN DISPLAY STATUS ALWAYS ON AUDIO CONTROLS SPEAKERS FRONT PANEL DISPLAY BRIGHTNESS 75 SETUP REAR PANEL CONFIG AN SYNC DELAY OFF DISPLAYS CUSTOM NAME OFF VOLUME CONTROLS EDIT CUSTOM NAME TRIGGERS LOCK OPTIONS become unsynchronized in a system Setting a corresponding audio delay with A V SYNC DELAY restores synchronization A V SYNC DELAY can be set in 1ms increments within its 1 to 60ms parameter range When setting the A V SYNC DELAY parameter it is recommended to use a news broadcast or another source that does not utilize Automated Dialog Replacement When set to OFF the parameter is deactivated CUSTOM NAME A 9 custom name CUSTOM NAME displays the text entered in the EDIT CUSTOM NAME parameter When set to ON the custom name will scroll across the on screen and front panel displays when the unit is powered on When set to OFF the custom name will not appear when the unit is powered on DISPLAY SETUP ON SCREEN DISPLAY FRONT PANEL DISPLAY AN SYNC DELAY OFF CUSTOM NAME OFF EDIT CUSTOM NAME 9 EEE EDIT CUSTOM NAME allows the creation of a c
93. e set in the VOLUME CONTROL SETUP menu see page 3 34 The Mute LED lights whenever mute is activated either manually or automatically by the unit For example the unit will briefly activate mute when changing input types or listening modes Q Main Input Selection Buttons select the input in the Main Zone and light a corresponding blue LED When the unit is in standby pressing one of these buttons also activates the Main Zone Zone 2 and the Record Zone will remain deactivated until one of those inputs is selected Q Main Off deactivates the Main Zone Q Zone 2 Input Selection Buttons select the input in Zone 2 and light a corresponding amber LED When the unit is in standby pressing one of these buttons also activates Zone 2 The Main and Record Zones will remain deactivated until one of those inputs is selected Zone 2 Off deactivates Zone 2 Record Input Selection Buttons select the input in the Record Zone and light a corresponding red LED When the unit is in standby pressing one of these buttons also activates the Record Zone The Main Zone and Zone 2 will remain deactivated until one of those inputs is selected Q Record Off deactivates the Record Zone 2 3 Basic Operation JBL REAR PANEL OUTPUTS MCA a OUTPUTS A Do RS 232 L SUBWOOFER R CAUTION Never make or break connections to the unit unless the power switch and all associated equipme
94. e whenever the unit is powered on When set to LAST LVL the Main Zone will power on at the last volume level that was active in that zone during the previous operating session MUTE LEVEL FULL 40dB 30dB 20dB 10dB MUTE LEVEL establishes the amount of attenuation that occurs in the Main Zone whenever the Mute button is pressed When set to FULL the Main Zone volume level will be fully attenuated ZONE PWR ON LAST LVL 80 to 6dB ZONE PWR ON establishes the volume level that will be active in Zone 2 whenever the unit is powered on When set to LAST LVL Zone 2 will power on at the last volume level that was active in that zone during the previous operating session REC PWR ON LAST LVL 80 to 6dB REC PWR ON establishes the volume level that will be active in the Record Zone whenever the unit is powered on When set to LAST LVL the Record Zone will power on at the last volume level that was active in that zone during the previous operating session 3 34 The SETUP Menu SDP 40 MAIN MENU gt SETUP gt TRIGGER SETUP MODE ADJUST INPUTS TRIGGER 1 PROGRAM AUDIO CONTROLS SPEAKERS TRIGGER 2 PROGRAM SETUP REAR PANEL CONFIG DISPLAYS Selecting either TRIGGER 1 VOLUME CONTROLS or TRIGGER 2 accesses an LOCK OPTIONS menu TRIGGER SETUP There are three 12V DC TRIGGER OUTPUTS on the rear panel that can be used to control other devices with compatible trigger
95. ed below are accessible WE IN 4 from all INPUT SETUP menus pictured on the previous ANALOG IN NONE page These menus are identical regardless of which ANLG IN LVL AUTO input is selected VIDEO IN S VIDEO 1 COMPONENT IN 1 2 CH L7 FILM oa D 5 1 L7 FILM TAES dis ES L7 FILM MAIN ADVANCED ZONE2 ADVANCED RECORD ADVANCED DVD1 INPUT NAME DVD1 ANALOG IN DVD1 VIDEO IN DVD1 2 CH MODE DVD1 D MODE DVD1 MAIN ADV EDIT INPUT NAME ANALOG 1 COMPOSITE 1 121 FILM 5 1 151 FILM INPUT SELECT DIGITAL RESTORE DEFAULT NAME ANALOG 2 COMPOSITE 2 121 TV 5 1121 TV ANALOG BYPASS OFF ANALOG 3 COMPOSITE 3 121 MUSIC 5 1 151 MUSIC S VIDEO 16 9 AUTO DVD1 DIGITAL IN ANALOG 4 COMPOSITE 4 PL THX 5 1 THX SUR EX S VIDEO OSD 4 3 ON ANALOG 5 COMPOSITE 5 PRO LOGIC II DO DIGITAL COMPONENTOSD OFF ANALOG 6 S VIDEO 1 DO PL Il MUSIC 5 1 2 CHANNEL ANALOG 7 S VIDEO 2 PRO LOGIC 5 1 MONO us ANALOG 8 S VIDEO 3 2 CHANNEL 5 1 MONO LOGIC eee NONE S VIDEO 4 PARTY 5 1 MONO SURR m S VIDEO 5 MONO USE LAST INPUT SELECT DIGITAL COAX 6 S VIDEO 6 MONO LOGIC DVD1 ANLG IN LVL S VIDEO 7 MONO SURROUND OPTICAL 1 VO AAE NODE DVD1 RECORD ADV OPTICAL 2 S VIDEO 8 USE LAST OPTICAL 3 AUTO ON NONE es 151 FILM INPUTSELECT DIGITAL MANUAL 008 ANLG IN LVL 048 OPTICAL 4 ETA s 19 MUSIC DIGITAL BYPASS OFF OPTICAL 5 DVD1 COMPONENT ARS TEX OPTICAL 6 AUTO GAIN 0 0dB ES DIG OUT RATE 44 1kHz AES EBU ERR g g p COMPONENT 4 RECORD ENABLED NONE COMPONENT 2
96. ed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and radiates radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio or television reception which can be determined by turning the equipment off and on The user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and the receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio television technician for help JBL Synthesis 8500 Balboa Boulevard Northridge CA 91329 250 Crossways Park Drive Woodbury NY 11797 800 336 4JBL Part No 070 14991 0 10 01 Manufactured under license from Dolby Laboratories Dolby Pro Logic and the double D symbol are trademarks of Dolby laboratories Lucasfilm and THX are trademarks or registered trademarks of Lucasfilm Ltd Lucasfilm Ltd amp TM Surround EX is a jointly developed technology of THX and Dolby Laboratories Inc and is a trademark of Dolby Laboratories Inc All rights reserved Used under authorization Manufactured under license from Digital Theater Systems Inc U S Pat No 5 451 942 5 956 674 5 974 380 5 978 762 and other world wide pate
97. ee page 5 17 for more information CUSTOM See page 5 17 for more information An alphabetical listing of parameter descriptions begins on page 5 20 5 1 LOGIC7 FILM MODE ADJUST gt 5 115 FILM A proprietary Lexicon listening mode e Designed for playback of 5 1 channel Dolby Digital film sources e Utilizes several techniques to derive seven channels from 5 1 channel input types With side and rear speakers selected 5 1 LOGIC7 FILM also increases the perceived length and sense of envelopment of the listening space e Provides remarkable improvement compared to other decoders Recommended for 5 1 channel Dolby Digital film sources even when only one pair of surround speakers is selected Default Parameter Value Values VOCAL ENHANCE 0 0dB 0 0 3 0dB 6 0dB 5 SPKR ENHANCE OFF ON OFF BASS ENHANCE OFF ON OFF RE EQUALIZER ON ON OFF REAR DLY OFFSET 15ms 0 to 30ms COMPRESSION OFF AUTO ON OFF LFE MIX 0 0 10 0 to 0 0 OUTPUT LEVELS See page 5 17 for more information CUSTOM See page 5 17 for more information An alphabetical listing of parameter descriptions begins on page 5 20 40 The MODE ADJUST Menu 5 1 LOGIC7 TV eg A proprietary Lexicon mode e Designed for playback of 5 1 channel Dolby Digital TV sources e Based on 5 1 LOGIC7 FILM but specifically tailored for TV sources Recommended for 5 1 channel Dolby Digital TV sources even when
98. ent The ANALOG BYPASS parameter on the MAIN ADV menu is set to OFF see page 3 13 Parameter Values INPUT The name of the selected input MODE The name of the selected listening mode INPUT TYPE ANLG SAMPLE RATE 96kHz An alphabetical listing of parameter descriptions begins on page 5 20 The MODE ADJUST Menu JBL dts STATUS MENU The dts STATUS menu will appear when a dts ES listening mode is selected It features L C R SL SR SB and LFE level meters see page 5 18 for more information The SB level meter will not appear unless a 6 1 channel input type is selected Parameter Values INPUT The name of the selected input MODE The name of the selected listening mode CHANNELS 3 3 1 3 2 1 ES DECODE MATRIX DISCRETE OFF SAMPLE RATE 44 1kHz 48kHz An alphabetical listing of parameter descriptions begins on page 5 20 MODE PARAMETER DESCRIPTIONS 5 SPKR ENHANCE ON OFF 5 SPKR ENHANCE Five Speaker Enhance simulates seven speaker playback through a five speaker system When set to ON the unit provides an increased sense of spaciousness and envelopment through two surround speakers This enhancement is most noticeable when these surround speakers are positioned to the side of the listening position or when the listening position is located against the rear wall The effectiveness of this parameter varies within the listening space For optimum results position the side
99. ent video inputs one BNC with full HDTV compatibility BNC component video output 8 S video inputs 5 composite video inputs 4 32 bit DSP engines Broadcast quality video switching LOGIC7 decoding Dolby Digital Dolby Pro Logic II and Dolby Pro Logic decoding dts and dts ES discrete amp matrix decoding THX Ultra certification THX Surround EX decoding Upgradable software using RS 232 3 internal slots for future expansion Removable access panel for future expansion 2 digital audio outputs RS 232 control Rear panel IR IN connector 4 rear panel microphone inputs for future expansion 3 trigger outputs 19 rack mount kit option included Balanced audio outputs Getting Started JBL USING THE DOCUMENTATION The SDP 40 has many impressive features It is designed to be customized to individual systems and listening spaces For these reasons the information contained in this user guide is extensive Refer to this documentation for assistance with installation calibration and operation of the unit Settings that are reached during the calibration process can be recorded on the installation worksheet located in the Appendix see page A 12 USER GUIDE SYMBOLS Following are symbols that appear throughout this user guide Calls attention to a procedure practice condition or the like that if not correctly performed or adhered to could result in injury or death CAUTION Calls attention to a procedur
100. erfecto al transportista informe de cualquier problema de funcionamiento del equipo a su distribuidor Contenu de l emballage et inspection Apr s avoir ouvert l emballage conservez le pour tout retour Inspectez avec soin les modules et les mat riaux d emballage pour tout signe de dommage Veuillez rapporter imm diatement les dommages aupr s du transporteur Les dysfonctionnements du mat riel doivent tre signal s votre revendeur Disimballaggio ed ispezione Dopo aver disimballato l unit salvi tutto il materiale d imballaggio in caso Lei abbia bisogno di spedire l unit Ispezioni attentamente i moduli ed il materiale d imballaggio per vedere se riportano segni di danno Riporti subito ogni segno di danno al corriere riferisca il malfunzionamento dell attrezzatura al suo rivenditore xi 1 Getting Started i A 1 2 1 3 Using the Doc rmernLtatiOFi ips caca eoo xe tn eripe Pepe peu eg ea eo 1 4 Location Considerations erede rro t pto Pee re ER p Ore 1 4 Navigating the Mela 1 4 TWo line etum e pe yt dee pe etu 1 5 Restoring Factory Default Settings 1 5 Getting Started JBL Thank you for purchasing the SDP 40 Digital Controller a reference quality 12 channel digital surround processor with built in digital audio processing 12 configurable in
101. es are also available but not recommended for 5 1 Dolby Digital sources The unit will automatically select 5 1 MONO LOGIC when a 1 0 Dolby Digital input type is preset 5 1 MONO LOGIC ADJUST gt 5 1 MONO LOGIC Designed for playback of Dolby Digital mono sources e Utilizes proprietary Lexicon reverb technology to realistically expand Dolby Digital mono sources to utilize all channels dramatically increasing the perceived length and sense of envelopment of the listening space Default Parameter Value Values EFFECT LVL 9dB 12 to 6dB ACADEMY FILTER ON ON OFF SURR ROLLOFF 3 1kHz 500Hz to 20 0kHz OFF OUTPUT LEVELS See page 5 17 for more information CUSTOM See page 5 17 for more information An alphabetical listing of parameter descriptions begins on page 5 20 5 12 40 The MODE ADJUST Menu 5 1 SURROUND MODE ADJUST gt 5 1 MONO SURR e Designed for playback of Dolby Digital mono sources e Sends mono signals to all channels dts ES LOGIC7 film ISTIS gt ES proprietary Lexicon listening mode Designed for playback of 5 1 and 6 1 channel dts ES film sources Utilizes an advanced matrix to derive seven channels from 5 1 or 6 1 channel input types With side and rear speakers selected dts ES LOGIC7 FILM increases the perceived length Default Parameter Value Values OUTPUT LEVELS See page 5 17 for more information CUSTOM See page 5 17 for mo
102. et of the CENTER output that is encoded into the FRONT L R outputs The recommended setting for the CNTR DLY SAMPLES parameter is 0 unless the CENTER channel is not properly timed and the value of the error is known COMPRESSION AUTO ON OFF COMPRESSION increases dialog intelligibility at lower volume levels When set to AUTO Dolby Digital input types are automatically compressed based on volume level When set to ON full compression is applied regardless of volume level When set to OFF compression is not applied This parameter should be set to AUTO or ON for Dolby Digital sources that are listened to at lower volume levels 5 21 The MODE ADJUST Menu JBL CTR WIDTH MIN 1 to 6 MAX CTR WIDTH Center Width adjusts the center image When set to MIN the center image is heard from only the center speaker When set to MAX the center image is heard from only the front left and right speakers as a phantom center image When set on the 1 to 6 scale the center image is heard in various combinations of all three front speakers CUSTOM See page 5 17 for information about CUSTOM DIMENSION FRONT NEUTRAL REAR DIMENSION adjusts the relative balance of the soundfield which can be useful to achieve a more suitable balance from all speakers with certain recordings When set to FRONT the soundfield is balanced toward the front of the listening space When set to NEUTRAL the soundfield is balanced at the center of the
103. etting in 1dB increments Gradually increase the setting until the subwoofer begins to overload then reduce the setting until the subwoofer stops overloading Press the left MENU arrow to accept the setting and exit the parameter LFE LIMITER ON OFF LFE LIMITER affects the LFE output When set to ON the output level of the LFE output will be restricted to the limit specified in the LFE LIMIT ADJ parameter When set to OFF the output level of the LFE output will not be restricted The LFE LIMITER should be set to OFF when the LFE subwoofer has built in limiter protection LFE LIMIT ADJ 75 to 115dB LFE LIMIT specifies the output level restriction placed on the LFE output when the LFE LIMITER parameter is set to ON Press the right MENU arrow to select this parameter for adjustment Its setting will automatically change to 75dB Use the up and down MENU arrows to increase and decrease the setting in 1dB increments Gradually increase the setting until the subwoofer begins to overload then reduce the setting until the subwoofer stops overloading Press the left MENU arrow to accept the setting and exit the parameter 3 29 The SETUP Menu JBL Note If 5 STEREO amp 5 1 ANLG is selected on the REAR PANEL CONFIG menu the unit will automatically select the 5 1 BYPASS listening mode if the following conditions are also met MAIN MENU gt SETUP REAR PANEL CONFIG MODE ADJUST INPUT
104. exit the pulldown menu without restoring the factory default name of the selected input 3 4 The SETUP Menu SDP 40 MAIN MENU gt SETUP gt INPUT SETUP DVD1 INPUT SETUP gt DVD1 DIGITAL IN MODE ADJUST INPUTS DVD1 NAME DVD1 COAX 1 AUDIO CONTROLS SPEAKERS DVD2 DIGITAL IN COAX 1 COAX 2 SETUP REAR PANEL CONFIG LD ANALOG IN NONE COAX 3 DISPLAYS TV ANLG IN LVL AUTO COAX 4 VOLUME CONTROLS SAT VIDEO IN S VIDEO 1 COAX 5 TRIGGERS VCR COMPONENT IN 1 COAX 6 LOCK OPTIONS CD 2 CH L7 FILM OPTICAL 1 PVR 00 5 1 L7 FILM OPTICAL 2 GAME TIMES dts L7 FILM OPTICAL 3 TAPE MAIN ADVANCED OPTICAL 4 TUNER ZONE2 ADVANCED OPTICAL 5 AUX RECORD ADVANCED OPTICAL 6 AES EBU DVD1 is used as an example in this illustration and will continue to be used as an example NONE throughout this section Whenever DVD1 appears as a step in a menu path any other input may be substituted DIGITAL IN Tl gt MUA gt gt MD Note Selecting DIGITAL IN accesses the DIGITAL IN menu which can be used to assign the digital connector for the selected input Digital input selection will take precedence over analog input selection unless No valid digital input signal is present The DIGITAL IN parameter is set to NONE The INPUT SELECT parameter on the MAIN ADV menu is set to ANALOG see page 3 13 When DIGITAL IN is set to NONE the INPUT SELECT parameter on the MAIN AD
105. factory default settings 6 The message FACTORY SETTINGS BEEN RESTORED will appear on the screen Press any front panel or remote control button to restart the unit ROUTINE MAINTENANCE The following routine maintenance should be performed on a periodic basis e Clean the exterior surfaces of the unit with a soft lint free cloth Do not use alcohol benzene acetone based cleaners or strong commercial cleaners Do not use a cloth made with steel wool or metal polish If the unit is exposed to a dusty environment a low pressure blower may be used to remove dust from its exterior e Change the remote control batteries as needed When the bat teries are low on power the remote control will enter a low voltage condition that prevents it from operating the unit Operation will be restored when new batteries are installed Appendix SPEAR las A 2 Declaration of Conformity 2 pne eds 4 Men MEE is EH ay e 5 Installation Worksheet ete ER Erst E ER orn A 12 Appendix JBL SPECIFICATIONS Audio Inputs and Outputs Audio Inputs 8 stereo pairs RCA or 5 stereo pairs and one 5 1 channel analog input Digital Audio Inputs Sample Rates Accepts 6 coaxial RCA 6 optical 5 TosLink and 1 optical mini jack 1 AES EBU coaxial and optical inputs conform to IEC 958 S PDIF standards 44 1 48 88 2 96kHz 16 2
106. following conditions are met ANALOG BYPASS continued ON OFF e S VIDEO OSD 4 3 parameter is set to OFF When ANALOG BYPASS is set to OFF the unit routes the analog anamorphic trigger signal is present input signal through analog to digital conversion internal e Th 16 9 displ processing and digital to analog conversion This makes it possible d HE as M cd to utilize internal processing including listening modes crossovers PPS and equalization COMPONENT OSD ON OFF Neither Zone 2 nor the Record Zone provide multi channel outputs If the 5 1 channel analog input is selected for Zone 2 or the Record Zone only the front left and right L R inputs will be available S VIDEO 16 9 AUTO OFF S VIDEO 16 9 controls the passage of anamorphic video trigger signals When set to AUTO the unit allows anamorphic trigger signals to pass through the S video switcher This enables compatible display devices to automatically switch between anamorphic and non anamorphic display modes When set to OFF the unit prevents anamorphic trigger signals from passing through the S video switcher This disables compatible display devices from switching between anamorphic and non anamorphic display modes S VIDEO OSD 4 3 ON OFF S VIDEO OSD 4 3 controls the appearance of the on screen display When set to ON the on screen display utilizing the S video output is displayed in a 4 3 aspect ratio regardless of the aspect r
107. gital and analog audio input types such as a laser disc player Note Some sources supply valid digital audio input types that remain active even when no audio is present in the signal Because the unit recognizes these as valid digital audio input types it will not switch to the ANALOG connector For these sources it is recommended to configure two different inputs one for digital audio input types and a second for analog audio input types ANALOG BYPASS ON OFF ANALOG BYPASS allows analog input types to bypass analog to digital conversion and internal processing When set to ON the unit passes the analog input signal to the corresponding analog outputs For stereo analog sources the input is sent to the FRONT L R outputs For a 5 1 channel analog source the L input is sent to the FRONT L output The R input is sent to the FRONT R output The C input is sent to the CENTER output The SUB input is sent to the SUBWOOFER L R and LFE outputs The LS input is sent to the SIDE and REAR L outputs The RS input is sent to the SIDE and REAR R outputs Note It is not possible to record from an analog input source on the S PDIF outputs when the Main Zone is utilizing the 5 1 channel analog input continued on page 3 14 The SETUP Menu JBL MAIN ADVANCED continued Note SETUP INPUT VD1 SETUP e e e The menu will appear horizontally stretched across the entire screen if the
108. glass cabinet However smoked glass will reduce the range of the remote control as well as the readability of the front panel display NAVIGATING THE MENUS The remote control must be used to navigate MAIN MENU through the extensive menu structure see page 2 8 for more information about the AUDIO CONTROLS remote control Pressing the MENU button accesses the MAIN MENU pictured at the right which can be used to access the three primary menus MODE ADJUST AUDIO CONTROLS and SETUP These menus are discussed in Sections 5 4 and 3 The complete menu structure is illustrated in the Appendix beginning on page A 5 1 4 40 Getting Started The MENU arrows navigate through all menus when the MAIN command bank is active see page 2 8 for more information about command banks Press the up and down MENU arrows to scroll through menu items A scroll bar will appear on the right side of the screen when these items exceed the on screen margins Press the right MENU arrow to select the highlighted item Press the left MENU arrow to exit the current menu TWO LINE STATUS The two line status pictured at the right VOL appears on the on screen display whenever 5 1 L7 FILM 3098 the unit receives command or whenever the input type changes unless the STATUS parameter on the ON SCREEN DISPLAY menu is set to OFF see page 3 31 Pressing the STAT b
109. he unit sends digital audio output through a sample rate converter before passing it to the S PDIF outputs This allows the digital output signal to match the input of a digital recording device Note Changing the setting of the DIG OUT RATE parameter will cause the RECORD AUDIO OUTPUT labelled S PDIF to mute momentarily Otherwise DIG OUT RATE parameter settings will be ineffective when the DIGITAL BYPASS parameter is set to ON DIG OUT RATE 44 1kHz 48kHz 88 2kHz 96kHz INPUT DIG OUT RATE sets the S PDIF output sampling rate for analog or digital inputs When set to INPUT the unit varies the S PDIF audio output rate to match the sampling rate of the input signal When set to a numerical value the output sampling rate remains at the selected value This is useful for recording devices that operate on a single sampling rate such as CD R 44 1kHz RECORD ENABLED BLOCKED RECORD prevents feedback loops with recording devices When set to ENABLED the unit allows record signals from the selected input to pass to the RECORD AUDIO and VIDEO OUTPUTS When set to BLOCKED the RECORD AUDIO OUTPUTS are blocked preventing feedback loops However the unit will still pass video signals to the RECORD VIDEO OUTPUTS The SETUP Menu JBL SPEAKER SETUP CUSTOM SETUP EE The CUSTOM SETUP menu can be used to configure the MAIN AUDIO OUTPUTS for a custom speaker system For a Synthesis 7 channel
110. ide video output in the Main Zone One component BNC two composite and two S video outputs are available The component video output is only available when component video inputs are used Composite video outputs are available when composite or S video inputs are used S video outputs are only available when S video inputs are used Output 1 OSD incorporates the on screen display output 2 does not The ZONE 2 AUDIO OUTPUTS provide analog audio output in Zone 2 Two stereo outputs one fixed one variable are available The variable output includes a built in volume control the fixed output does not The RECORD AUDIO and VIDEO OUTPUTS provide audio and video output in the Record Zone Two composite two S video two analog stereo one fixed one variable one S PDIF coaxial and one S PDIF optical outputs are available Note When analog input sources are used the ZONE 2 and RECORD AUDIO OUTPUTS are about 2dB higher than the MAIN AUDIO OUTPUTS labelled FRONT L R When digital input sources are used the ZONE 2 and RECORD AUDIO OUTPUTS are about 8dB higher than the MAIN AUDIO OUTPUTS labelled FRONT L R This is to accommodate THX level requirements The AES EBU and S PDIF INPUTS provide digital audio input One AES EBU six S PDIF coaxial and six S PDIF optical including one optical mini jack inputs are available continued on page 2 6 2 5 Basic Operation JBL REAR PANEL continued o
111. ided both side and rear speakers are selected see page 3 18 The default value of this parameter is ON which activates the 5 1 THX SURROUND EX listening mode When set to OFF the 5 1 THX SURROUND EX listening mode becomes 5 1 THX Toggling the setting of the SURROUND EX parameter produces low level clicks in the front speakers 5 1 THX SURROUND EX Designed for playback of Dolby Digital Surround EX encoded sources Similar to 5 1 THX but utilizes Dolby Pro Logic to decode three surround channels from Dolby Digital Surround EX encoded input types Applies re equalization and timbre matching Re equalization simulates the high frequency rolloff that occurs in a movie the ater as sound travels from the speakers to the listeners Most films are mixed for movie theaters and may sound too bright when played back in a home theater without re equalization Timbre matching helps minimize the timbre differences between the front and side channels which results in smoother sound movements between these channels Recommended for Dolby Digital Surround EX encoded sources 5 1 THX Designed for playback of 5 1 channel Dolby Digital encoded sources e Utilizes Dolby Digital to decode 5 1 discrete channels from 5 1 Dolby Digital encoded input types e Applies re equalization timbre matching and adaptive decorrelation Re equalization simulates the high frequency rolloff that occurs in a movie theater as sound travels from the front spea
112. iff rences nettes dans son fonctionnement indiquant la n cessit de r parations Cet appareil ne doit tre ouvert que par un personnel de service qualifi En enlevant les couvercles vous vous exposez des tensions lectriques dangereuses dangereuse non isol e l int rieur du bo tier une tension suffisante Ce triangle sur votre appareil vous avertit de la pr sence de tension pour repr senter un danger d lectrocution instructions d utilisation et d entretien dans la documentation livr e f Ce triangle sur sur votre appareil vous invite de suivre d importantes avec le produit ITALIANO IMPORTANTI NORME DI SICUREZZA Conservare le presenti norme per l utilizzo futuro e Osservare tutte le istruzioni e le avvertenze apposte sull unit e Utilizzare esclusivamente con la tensione di rete corretta Consultare le istruzioni operative fornite dal fabbricante per i dati riguardanti la tensione e l assorbimento di corrente Potrebbe essere necessario l uso di cavi di rete e o di spine diverse a seconda della tensione utilizzata Non installare l unit in uno scaffale privo di ventilazione oppure direttamente sopra una fonte di calore come ad esempio un amplificatore Non superare la temperatura ambientale massima di funzionamento riportata nei dati tecnici del prodotto Le fessure le altre aperture nella scatola servono alla ventilazione un funzionamento affidabile e per evitare
113. ill be redirected to the SUBWOOFER L R outputs If the lowest crossover setting is FULL no low frequencies will be redirected to the SUBWOOFER L R outputs 3 18 40 The SETUP Menu FREQUENCY RESPONSE CURVES dB 0 60 10 20 50 100 200 500 1k Hz LLL 4 p 2E L 7 VYYVYYV 7 Lowpass Filter The lowpass filter attenuates high frequencies at 24dB per octave The curves show the frequency response of each crossover setting From left to right the curves represent crossover settings from 30Hz to 120Hz Highpass Filter The highpass filter attenuates low frequencies at 24dB per octave The curves show the frequency response of each crossover setting From left to right the curves represent crossover settings from 30Hz to 120Hz This graph does not illustrate the THX 80Hz setting which is 1 2dB per octave 3 19 The SETUP Menu JBL MAIN MENU gt SETUP SPEAKER SETUP CUSTOM SETUP FRONT L R SPEAKERS MODE ADJUST INPUTS FULL AUDIO CONTROLS SYNTHESIS 7CH SETUP 80Hz 30Hz CENTER SPEAKER REAR PANEL CONFIG SPEAKER DISTANCES SIDE L R 80Hz 40Hz DISPLAYS LEVELS CALIBRATION REAR L R 80Hz 50Hz FULL VOLUME CONTROLS 1 e SUB L R MONO 60Hz 30Hz
114. in conditions are met Level Meters All listening mode STATUS menus feature level meters which indicate fluctuating input levels in the left L center C right R surround left SL surround right SR surround back SB and LFE channels Different combinations of level meters appear on each STATUS menu Only the L and right R level meters appear on the 2CH STATUS menu The SB level meter will not appear unless a 6 1 channel input type is present All level meters appear in combinations of green yellow and red on the blue screen background Green indicates normal input levels yellow indicates the onset of overload and red indicates overload The yellow arrow to the right of each bar indicates the current input peak level 2CH STATUS MENU The 2CH STATUS menu will appear when a 2 channel listening mode is selected It features L and R level meters see previous column for more information Parameter Values INPUT The name of the selected input MODE The name of the selected listening mode INPUT TYPE ANLG DOLBY D PCM SAMPLE RATE 44 1kHz 48kHz 88 2kHz 96kHz An alphabetical listing of parameter descriptions begins on page 5 20 2CH BYPASS STATUS MENU The 2CH BYPASS STATUS menu will appear when the 2CH BYPASS listening mode is selected It features L and R level meters see previous column for more information Parameter Values INPUT The name of the selected input MODE 2CH BYPASS IN
115. in komponent anger att viktiga A bruksanvisningar och serviceanvisningar ing r i dokumentationen i fr ga 40 Introduction Unpacking and Inspection After unpacking the unit save all packing materials in case you ever need to ship the unit Thoroughly inspect the modules and packing materials for signs of damage Report any damage to the carrier at once report equipment malfunction to your dealer Desempacotando e Inspec o Depois de desempacotar a unidade economiza todos os materiais de embalagem no caso de voc j precisa transportar a unidade Completamente inspecione os m dulos e empacotando materiais para sinais de dano Informe qualquer dano imediatamente ao portador mau funcionamento de equipamento de relat rio para seu negociante Auspacken und berpr fung Bewahren Sie nach dem Auspacken des Ger ts das Verpackungsmaterial f r den Fall auf dass Sie das Ger t wieder versenden m ssen berpr fen Sie die Module und die Verpackung sorgf ltig auf Anzeichen von Besch digung Etwaige Sch den sind dem Transporteur unverz glich anzuzeigen Funktionsst rungen sind dem zustandigen Handler zu melden Desembalaje e inspecci n Despu s de desembalar la unidad guarde todos los materiales de embalaje por si alguna vez transportar la unidad Inspeccione con atenci n los m dulos y los materiales de embalaje para comprobar que no muestren desperfectos Informe inmediatamente de cualquier desp
116. ine of sight with this receiver for proper operation If the unit is placed inside a glass cabinet smoked glass will reduce the range of the remote control Make certain the batteries are inserted correctly with the proper polarity Are the batteries low on power When the they are the remote control will enter a low voltage condition that prevents it from operating the unit Operation will be restored when new batteries are installed THE UNIT IS ON BUT THERE IS NO AUDIO 1 Make sure the full mute setting is not activated The message FULL MUTE ON will appear in the top left corner of the on screen and front panel displays when the full mute setting is activated Press the Mute button or adjust the volume level to deactivate the full mute setting Increase the volume level to make sure it is set to an audible level Check the STATUS menu to ensure a signal is coming into the unit Press SHIFT then STAT on the remote control to access the STATUS menu Make sure the associated power amplifier s are powered on THE UNIT IS ON BUT THERE IS NO VIDEO 1 Check the video cables particularly the S video cables to ensure good connections Check the VIDEO IN and COMPONENT IN parameters on the INPUT SETUP menu see pages 3 8 and 3 9 Make sure the appropriate connector is assigned to the selected input DIALOG SOUNDS MUFFLED 1 If the system does not include a center channel make sure the CENTER parameter th
117. interrupt automatic scrolling and manually select an output Press the right MENU arrow to select an output for adjustment then use the up and down MENU arrows to increase and decrease the level of the selected output in 0 5dB increments within a range of 18 to 12dB Adjust all output levels to achieve a 75dB reading on the SPL meter from the primary listening position Press the left MENU arrow to exit the selected output and resume automatic scrolling Note Speakers that are set to NONE on the CUSTOM SETUP menu cannot be adjusted during the INTERNAL NOISE TEST These speakers can be adjusted during DACS CALIBRATION but this is not recommended DACS CALIBRATION Selecting either INTERNAL NOISE TEST or DACS CALIBRATION accesses the SPEAKER LEVEL ADJUST menu pictured on the previous page DACS CALIBRATION requires an external noise source In JBL Synthesis systems this source is the JBL Digital Acoustical Calibration System DACS However an alternate source such as an audio calibration disc can also be used As the noise test is conducted the SDP 40 loads the DOLBY Pro Logic II Dolby Digital or dts ES utilizing the signal from the DACS calibration system or audio calibration disc For example if an analog or PCM input type is coming into the unit when DACS CALIBRATION is conducted the unit will activate the DOLBY Pro Logic II listening mode If a Dolby Digital input type is coming in the unit will activate the
118. isungen auch f r spater auf Befolgen Sie alle auf der Vorrichtung stehenden Anweisungen und Warnungen Immer mit der richtigen Spannung verwenden Die Gebrauchsanweisungen des Herstellers informieren Sie ber die elektrischen Anforderungen Vergessen Sie nicht da bei verschiedenen Betriebsspannungen ggf auch verschiedene Leitungskabel und oder Verbindungsstecker zu verwenden sind Stellen Sie die Vorrichtung nicht in ein unbel ftetes Gestell oder unmittelbar ber w rmeerzeugende Ger te wie z B Tonverst rker Halten Sie die in den Produktspezifikationen angegebene maximale Umgebungstemperatur bei Betrieb ein Schlitze und ffnungen im Geh use dienen Bel fung um Betrieb sicherzustellen und berheizen zu vermeiden d rfen diese ffnungen nich verstopft oder abgedeckt werden Stecken Sie nie irgend einen Gegenstand durch die Bel ftungsschlitze VergieRen Sie keine Fl ssigkeiten auf den Apparat Dieses Produkt is mit einem 3 drahtigen Erdungsstecker ausger stet Diese Sicherheitsmanahme darf nicht unwirksam gemacht werden SchlieRen Sie nie Tonverst rker unmittelbar an einen Anschlu des Apparates an Um elektrischen Schlag oder Feuer zu vermeiden setzen Sie den Apparat weder Regen noch Feuchtigkeit aus und betreiben Sie ihn nicht dort wo Wasser eindringen k nnte Versuchen Sie nicht den Apparat zu betreiben falls er fallen gelassen besch digt oder Fl ssigkeiten ausgesetzt wurde o
119. ition relative to the When SUB L R is set to STEREO or NONE see page 3 22 the SUB parameter will appear as SUB LEFT speakers The unit features a speaker distance control used for entering distances for all speakers This feature is not a substitute for proper speaker placement though it does help to ensure accurate signal arrival times at the primary listening position Speaker distances can be set within a range of O to 30ft or O to 12m The UNITS parameter selects the desired unit of measurement The unit will automatically convert feet to meters or meters to feet when the parameter setting is changed To determine the appropriate setting measure the distance between the primary listening position and the front baffle of each speaker Enter the closest available value in the corresponding parameter Press the right MENU arrow to select the desired speaker for adjustment Press the up and down MENU arrows to increase and decrease the distance in 0 5ft or 0 2m increments Press the left MENU arrow once to exit the selected parameter and twice to exit the SPEAKER DISTANCES menu The SETUP Menu JBL MAIN MENU gt SETUP gt SPEAKER SETUP gt LEVELS CALIBRATION gt SPEAKER LEVEL ADJUST MODE ADJUST INPUTS CUSTOM SETUP FRONT LEFT 40 0dB AUDIO CONTROLS SYNTHESIS 7CH SETUP CENTER 0 00 REAR PANEL CONFIG SPEAKER DISTANCES SUB LIMITERS FRONT
120. jects of any kind through any of the ventilation slots Never spill any liquids on the unit Never attach audio power amplifier outputs directly to any of the unit s connectors To prevent shock or fire hazard do not expose the unit to rain or moisture or operate it where it will be exposed to moisture Do not attempt to operate the unit if it has been dropped damaged exposed to liquids or if it exhibits a distinct change in performance indicating the need for service This unit should only be opened by qualified service personnel Removing covers will expose you to hazardous voltages This triangle which appears on your component alerts you to the presence of uninsulated dangerous voltage inside the enclosure voltage that may be sufficient to constitute a risk of shock This triangle which appears on your component alerts you to AN important operating and maintenance instructions in this accompanying literature PORTUGUESE INSTRU ES DE SEGURAN A IMPORTANTEs Economize estas instru es para uso posterior e Siga todas as instru es e advert ncias marcadas na unidade e Sempre use com a voltagem de linha correta Se refira ao fabricante est operando instru es para as exig ncias de poder Seja aconselhado que voltagens operacionais diferentes requeiram para o uso uma corda de linha diferente ou tomada de anexo e N o instale esta unidade em uma prateleira de unventilated nem diretamente s
121. kers to the listeners Most films are mixed for movie theaters and may sound too bright when played back in a home theater without re equalization Timbre matching helps minimize the timbre differences between the front and side channels which results in smoother sound movements between these channels Adaptive decorrelation increases the perceived width of the listening space Since movie theaters utilize surround speaker arrays and most home theaters do not decorrelation of the mono surround channel increases the perceived width of the surround field in a home theater e Recommended for Dolby Digital encoded sources Default Parameter Value Values RE EQUALIZER ON ON OFF SURROUND EX ON ON OFF COMPRESSION OFF AUTO ON OFF LFE MIX 0 0dB 10 0 to 0 0dB OUTPUT LEVELS See page 5 17 for more information CUSTOM See page 5 17 for more information An alphabetical listing of parameter descriptions begins on page 5 20 5 10 40 The MODE ADJUST Menu DOLBY DIGITAL ADJUST gt DO DIGITAL Designed for playback of 5 1 Dolby Digital encoded sources e Decodes 5 1 discrete channels from 5 1 Dolby Digital encoded input types The five main channels are full frequency The 1 channel often referred to as the LFE or subwoofer channel has a limited frequency range of 120Hz e Appropriate for Dolby Digital encoded film sources Default Parameter Value Values COMPRESSION OFF
122. lay can be used to view the menus one menu item at a time The up and down MENU arrows can be used to scroll through all menu items provided the Main remote control command bank is active see page 2 8 The IR Receiver receives infrared commands from the remote control There are three LEDs located in this area an amber LED blinks when an infrared command is received a red LED lights when the analog to digital converters are overloading and a blue LED lights when the unit is on even when the front panel display is deactivated Volume Knob adjusts the volume level in the Main Zone When adjustments are made volume level is shown in dB on the on screen and front panel displays A horizontal bar graph illustrates adjustments Q mo Mode Up and Down Buttons scroll through available listening modes in the Main Zone Pressing the Mode Up button selects the previous listening mode pressing the Mode Down button selects the next listening mode See page 2 17 for more information about mode selection using the Mode up and down buttons Q Mute toggles between muting the volume level in the Main Zone and restoring the volume to its original level The first press lowers the volume level in the Main Zone and lights the amber LED on this button The message MUTE ON appears in the top left corner of the on screen and front panel displays The second press restores the volume in the Main Zone to its original level Mute level can b
123. ld them down Basic Operation JBL BANK Q Toggles the unit between on and standby When the unit is on pressing this button places the unit into standby and lights the red LED on the front panel Standby standby button When the unit is in standby pressing this button activates all zones that were active in the previous operating session Activates the remote control backlight making buttons more visible in the dark LIGHT The backlight also activates whenever any button is pressed and deactivates automatically o Accesses a bank of commands that control the Main Zone 9 Bank Selection Accesses a bank of commands that control Zone 2 and the Main Zone Buttons Accesses a bank of commands that control the Record and Main Zones N Accesses a bank of commands that control the Main Zone EN Note The buttons included on the chart above perform the same function regardless of which command bank is active 40 Basic Operation DOO lt Input Selection Buttons 0 660 6660 60660606868 Selects the input for the zone Selects the input for the zone Deactivates the Main Zone Deactivates Zone 2 Selects the input for the zone Deactivates the Record Zone Selects the input for the zone Sets LOUDNESS to ON Selects the input for the zone Sets LOUDNESS to OFF Selects
124. les between Toggles between Toggles between Toggles between MUTE lowering the fully muting the fully muting the fully muting the volume level in the Main Zone and restoring the volume to its original level Toggles between accessing and exiting the MAIN MENU volume level in Zone 2 and restoring the volume to its original level Centers ZONE 2 BALANCE volume level in the Record Zone and restoring the volume to its original level Centers RECORD BALANCE volume level in the Main Zone and restoring the volume to its original level Centers Main Zone BALANCE and FADER See Section 5 for more information about STATUS menus See Section 4 for more information about these AUDIO CONTROLS menu parameters 2 12 40 Basic Operation BANK MENU Arrows Scrolls upward through menu items Reserved for future expansion Reserved for future expansion Adjusts Main Zone FADER forward Scrolls downward through menu items Reserved for future expansion Reserved for future expansion Adjusts Main Zone FADER backward Exits the current menu Adjusts ZONE2 BALANCE left Adjusts RECORD BALANCE left Adjusts Main Zone BALANCE left Selects the highlighted menu item Adjusts ZONE2 BALANCE right Adjusts RECORD BALANCE right Adjusts Main Zone BALANCE right
125. lf and does not cover the costs of installation or removal from a fixed installation normal set up or adjustments claims based on any misrepresentation by the seller or performance variations resulting from installation related circumstances such as program source quality or AC power How to obtain warranty service If your JBL product ever needs service we may direct you to an Authorized JBL Warranty Station or ask you to send your unit to the factory for repair in which case we ll also supply a Service Return Authorization and complete shipping instructions If the product was purchased in a country other than the USA it is necessary to return the product to the distributor or selling location in the same country Either way you ll need to present the original bill of sale to establish the date of purchase Please do not ship your JBL product to the factory without our prior authorization In the United States please call 1 818 830 8757 for the location of the authorized warranty station nearest you If service under this warranty is not necessary but you have questions regarding the Installation or operation of this unit please contact your authorized JBL dealer or call 1 818 830 8757 for further assistance Who pays for what JBL will be happy to pay all labor and material expenses for all repairs covered by this warranty If necessary repairs are not covered by this warranty or if a unit is examined which is not in need of rep
126. listening space When set to REAR the soundfield is balanced toward the rear of the listening space EFFECT LVL 12 to 6dB EFFECT LVL Effect Level adjusts the amount of ambience applied to the listening mode ENCODING MATRIX NONE ENCODING indicates the presence MATRIX or absence NONE of Dolby Surround encoding ES DECODE DISCRETE MATRIX OFF ES DECODE indicates the presence or absence of dts ES decoding When the parameter value is DISCRETE the unit is decoding a 6 1 channel discrete input type When the parameter value is MATRIX the unit is decoding a 5 1 channel input type with a matrix encoded sixth channel When the parameter value is OFF the unit is decoding a standard dts non ES input type FRONT STEERING OFF MUSIC FILM FRONT STEERING adjusts front steering to match the input source When set to FILM maximum front steering is applied When set to MUSIC minimal front steering is applied When set to OFF no front steering is applied This parameter should be set to FILM for film sources and to MUSIC or OFF for music sources INPUT INPUT INPUT indicates the name of the selected input INPUT TYPE ANLG DOLBY D PCM INPUT TYPE indicates the current input type When the parameter value is ANLG a 2 channel analog audio input source is present When the parameter value is PCM a 2 channel digital audio input source is present When the parameter value is DOLBY D a Dolby Digital audio input sour
127. lume is adjusted p 12 N W N M NN ANN pl S 100 200 500 1k 2k 5k 10k 20k Hz BALANCE AUDIO CONTROLS gt BALANCE BALANCE controls the left to right balance of the Main Zone When BALANCE is selected a horizontal graph pictured on page 4 2 will appear on the screen below the parameter This graph illustrates the position at which the current setting falls within the entire parameter range Press the up MENU arrow to move the setting toward the right and the down MENU arrow to move the setting toward the left Press the left MENU arrow to close the graph and return to the AUDIO CONTROLS menu FADER AUDIO CONTROLS o FADER controls the front to back balance of the Main Zone When FADER is selected a horizontal graph pictured on page 4 2 will appear on the screen below the parameter This graph illustrates the position at which the current setting falls within the entire parameter range Press the up MENU arrow to move the setting forward and the down MENU arrow to move the setting back ward Press the left MENU arrow to close the graph and return to the AUDIO CONTROLS menu ZONE2 BALANCE AUDIO CONTROLS gt ZONE2 BALANCE ZONE2 BALANCE controls the left to right balanc
128. merical crossover setting the unit activates a crossover at the selected frequency Choose the setting closest to the low frequency rating of the rear left and right speakers See pages 3 18 and 3 19 for more information about crossover settings When set to NONE the unit redirects rear channel signals to the SIDE L R outputs When both the SIDE L R and REAR L R parameters are set to NONE the unit redirects surround channel signals to the FRONT L R outputs The SETUP Menu JBL MAIN MENU gt SETUP SPEAKER SETUP CUSTOM SETUP SUBWOOFERS L R MODE ADJUST INPUTS FRONT L R 80Hz MONO AUDIO CONTROLS SYNTHESIS 7CH SETUP CENTER 80Hz STEREO REAR PANEL CONFIG SPEAKER DISTANCES SIDE L R 80Hz NONE SUB XOVER DISPLAYS LEVELS CALIBRATION REAR L R 80Hz VOLUME CONTROLS Q SUB L R FULL TRIGGERS K SUB XOVER 80Hz 30Hz LOCK OPTIONS q LFE OFF 40Hz m 50Hz SA 60Hz e g m 70Hz 80Hz THX 80Hz 90Hz 100Hz 110Hz 120Hz CUSTOM SETUP continued e E 5 custom serur SUB L R MONO STEREO NONE The SUB L R parameter determines the configuration of the MAIN AUDIO OUTPUTS labelled SUBWOOFER L R When set to MONO the front left and right center side left and right and rear left and right channels are combined and sent to the SUBWOOFER L R outputs This setting is recommended for all Synthesis systems regardless of the number
129. n the dts and dts ES listening modes activating ES decoding when a dts ES input type is identified Designed for playback of 5 1 channel dts encoded sources Decodes 5 1 discrete channels from dts encoded input types The five main channels are full frequency The 1 channel often referred to as the LFE or subwoofer channel has a limited frequency range of 120Hz Appropriate for dts encoded film sources ES Designed for playback of 6 1 channel dts ES encoded sources Decodes 6 1 channels from dts ES encoded input types The six main channels are full frequency The surround back channel can be either discrete or matrix encoded The 1 channel often referred to as the LFE or subwoofer channel is filtered above 120Hz Appropriate for dts ES encoded film sources Default Parameter Value Values LFE MIX 0 0dB 10 0 to 0 0dB OUTPUT LEVELS See page 5 17 for more information CUSTOM See page 5 17 for more information An alphabetical listing of parameter descriptions begins on page 5 20 dts ES 2 CHANNEL MODEADIUST EEEN Designed for conversion of 5 1 or 6 1 channel dts ES input types to LOGIC7 encoded 2 channel input types e Allows 5 1 or 6 1 channel dts ES sources to be listened to through the front left and right channels e Reproduces the original 5 1 performance through playback of LOGIC7 listening modes e Recommended for recording purposes e The unit will automatically activate ES decodi
130. nd Main Zone listening modes Triggers cannot be associated with individual inputs in Zone 2 or the Record Zone TRIGGER 1 SETUP REMOTE CONTROL DVD1 DVD2 LD TV SAT VCR CD PVR GAME TAPE TUNER AUX ZONE2 INPUTS RECORD INPUTS 121 FILM 121 TV 121 MUSIC PL THX PRO LOGIC II PL Il MUSIC PRO LOGIC 2 CHANNEL PARTY MONO MONO LOGIC MONO SURROUND 5 1 1 FILM 5 1 iTV 5 1121 MUSIC 5 1 THX SUR EX DIGITAL 5 1 2 CHANNEL 5 1 MONO 5 1 MONO LOGIC 5 1 MONO SURR Eres 2 FILM ESES 151 MUSIC THX ass ESES 2 CHAN OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF 99 zm 222222 9 uim ud dix dim um dim uim o 4 SQooooooo ia diac diu dim diu di A The SETUP Menu JBL Note Locking settings in the MODE ADJUST AUDIO CONTROLS and SETUP menus will prevent accidental changes These menus can be unlocked at any time to adjust settings MAIN MENU gt SETUP LOCK OPTIONS MODE ADJUST INPUTS MODES UNLOCKED AUDIO CONTROLS SPEAKERS AUDIO CNTRL UNLOCKED REAR PANEL CONFIG SETUP UNLOCKED DISPLAYS VOLUME CONTROLS TRIGGERS LOCK OPTIONS The LOCK OPTIONS menu can be used to lock and unlock settings in the three primary menus MODE ADJUST AUDIO CONTROLS and SETUP Default Parameter Value Values MODES UNLOCKED LOCKED U
131. nd listening modes 3 24 40 The SETUP Menu MAIN MENU gt SETUP gt SPEAKER SETUP gt SPEAKER DISTANCES Note MODE ADJUST INPUTS CUSTOM SETUP FRONT LEFT 0 0ft When a JBL Digital Equalizer is AUDIO CONTROLS SYNTHESIS 7CH SETUP CENTER 0 0ft used in the system speaker REAR PANEL CONFIG FRONT RIGHT Gil distances should remain at their DISPLAYS LEVELS CALIBRATION SIDE RIGHT 0 0 fadtoredefdult settings lett The VOLUME CONTROLS Qj REAR RIGHT 0 0ft IET 9 gt TRIGGERS N 4 V REAR LEFT 0 0ft digital equalizer will perform LOCK OPTIONS 0 SIDE LEFT 0 0ft arrival time correction when D SUB MONO 0 0 calibrated zn A SUB RIGHT 0 0ft a 4 LFE SUB 0 0 UNITS FEET The parameters on the SYNTHESIS 7CH SETUP menu are not adjustable with the exception of REAR L R The default value of REAR L R is 80Hz which activates the rear speakers for use in a SYNTHESIS 7CH setup This setup requires rear speakers to be operational When set to OFF the REAR L R outputs are deactivated and the Surround EX parameter page 5 24 cannot be set to ON Note The SYNTHESIS 7CH SETUP menu is not adjustable with the exception of the REAR L R parameter To customize settings use the CUSTOM SETUP menu see page 3 18 SPEAKER DISTANCES e EGS 9 EEE Selecting SPEAKER DISTANCES accesses the SPEAKER DISTANCES menu which can be used to set the listener pos
132. ng when dts ES input type is identified Default Parameter Value Values CENTER MIX 0dB 25 to 25dB SURROUND MIX 0dB 5 to 5dB CNTR DLY SAMPLES 0 127 to 127 MASTER LEVEL 0dB 5 to 5db LFE MIX 0 0dB 10 0 to 0 0dB SUB L R LVL 0dB OFF 30 to 12dB CUSTOM See page 5 17 for more information An alphabetical listing of parameter descriptions begins on page 5 20 The MODE ADJUST Menu JBL 5 1 BYPASS MODE ADJUST gt 5 1 BYPASS Designed for playback of 5 1 channel analog input sources such as DVD A or SACD players e When selected the L input is sent to the FRONT L output The R input is sent to the FRONT R output The C input is sent to the CENTER output The SUB input is sent to the SUBWOOFER L R and LFE outputs The LS input is sent to the SIDE and REAR L outputs The RS input is sent to the SIDE and REAR R outputs The 5 1 BYPASS listening mode is not available unless and will be automatically selected when all of the following conditions are met e 5 STEREO amp 5 1 ANLG is selected the REAR PANEL CONFIG menu see page 3 30 e ANALOG IN parameter on the INPUT SETUP menu is set to 5 1 ANALOG see page 3 6 e The INPUT SELECT parameter the MAIN ADV menu is set to either AUTO or ANALOG see page 3 13 When set to AUTO no digital input types can be present e The ANALOG BYPASS parameter the MAIN ADV menu is set to ON see page 3 13
133. nt are powered off 2 4 40 Basic Operation Q me Power Switch disconnects power to the AC input connector The AC Input Connector provides power to the unit via the supplied power cord 3 wire 10 amp IEC 320 o The VIDEO INPUTS provide video input in the Main and Record Zones Eight S video five composite video and four component video inputs are available in the Main Zone All can be assigned in the INPUT SETUP menu see page 3 3 S video and composite video inputs are available in the Record Zone The AUDIO INPUTS provide analog audio input in all zones Eight stereo analog input pairs labeled 1 to 8 are available Pairs 6 7 and 8 can be configured as a 5 1 channel analog input These pairs function as L R C SUB and LS RS when the 5 1 channel analog input is selected see page 3 30 The MAIN AUDIO OUTPUTS provide analog audio output in the Main Zone Ten outputs labeled FRONT L R CENTER LFE SUBWOOFER L R SIDE L R and REAR L R are available The AUX L R outputs are reserved for future expansion Q The balanced MAIN and ZONE 2 AUDIO OUTPUTS provide analog audio output in the Main Zone and Zone 2 Ten outputs labeled FRONT L R CENTER LFE SUBWOOFER L R SIDE L R and REAR L R are available in the Main Zone The AUX L R outputs are reserved for future expansion Two connectors labeled ZONE 2 L R are available as a variable stereo output for Zone 2 Q The MAIN VIDEO OUTPUTS prov
134. nts issued and pending DTS DTS ES Extended Surround and Neo 6 are trademarks of Digital Theater Systems Inc 1996 2000 Digital Theater Systems Inc All rights reserved LOGIC7 and the LOGIC7 symbol are registered trademarks of Lexicon Inc a Harman International Company 2001 JBL Synthesis All rights reserved This document should not be construed as a commitment on the part of JBL Synthesis The information it contains is subject to change without notice JBL Synthesis assumes no responsibility for errors that may appear within this document Introduction 888850806856 88868868 Important Safety Instructions vi Instru es de Seguran a Importantes vi Wichtige Sicherheitsanweisungen vii Instrucciones Importantes de Seguridad vii Instructions de S ret Importantes viii Importanti Norme di Sicurezza viii Vigtig Information om Sikkerhed ix T rkeit Turvallisuusohjeita ix Viktig Informasjon om Sikkerhet Viktiga SakerhetsfOreskrifter x Unpacking and Inspection xi Desempacotando Inspe o xi Auspacken und berpr fung xi Desembalaje e inspecci n xi Contenu de l emballage et inspection xi Disimballaggio ed ispezione
135. o STEREO if utilizing two subwoofers to maximize the effectiveness of BASS ENHANCE If SUB L R is set to MONO it is recommended to use FRONT L R SIDE L R or REAR L R speakers that are capable of reproducing frequencies at 40Hz or lower See page 3 18 for more information about CUSTOM SETUP menu parameters Note BASS ENHANCE results will vary depending on room acoustics Most listening spaces will have 2 3dB reduction in low frequency energy when BASS ENHANCE is set to ON Use the BASS control to compensate for this reduction CENTER OFF 30 to 12dB CENTER adjusts the output level of the center channel CENTER MIX 25 to 5dB CENTER MIX adjusts the relative level of the center channel that is encoded into the front left and right channels The recommended settings 0dB for film sources and 5dB for music sources CHANNELS 3 3 1 3 2 1 3 2 3 1 2 2 2 1 2 0 1 0 CHANNELS indicates the number of channels present in the input type On the DOLBY DIGITAL STATUS menu the value of the CHANNELS parameter will be 3 2 1 3 2 3 1 2 2 2 1 2 0 or 1 0 On the dts STATUS menu the value of the CHANNELS parameter will be 3 3 1 or 3 2 1 The first digit indicates the number of front channels the digit after the represents the number of surround channels and the 1 indicates the presence of the LFE channel CNTR DLY SAMPLES 127 to 127 CNTR DLY SAMPLES Center Delay Samples adjusts the relative time offs
136. o highlight RESTORE DEFAULTS then press the right MENU arrow to restore factory default settings Selecting the EXIT option with the right MENU arrow will cancel the restoration of factory default settings The message FACTORY SETTINGS BEEN RESTORED will appear on the screen Press any front panel or remote control button to restart the unit 2 Basic Operation Front Panel Pep T e 2 2 Rear PANEL Up tt ans Dit 2 4 Remote 2 6 Understanding the 20 Pee FE o HM pk E RS 2 15 Understanding Listening Mode 2 16 Basic Operation JBL FRONT PANEL JEL SYNTHESIS ER CI RECEIVER Red LED Blue LED Amber LED 0 amp Standby toggles the unit between on and standby When the unit is on pressing this button places the unit into standby and lights the red LED on this button Power is still supplied to the unit when it is in standby When the unit is in standby pressing this button activates all zones that were active in the previous operating session 2 2 40 Basic Operation The Front Panel Display indicates the current input name top left the current listening mode name bottom left the current input type top center and the current volume level right This 2 by 20 character disp
137. obre artigos que geram calor como amplificadores de poder Observe o m ximo que temperatura operacional ambiente listou na especifica o de produto e S o providas as aberturas no caso para ventila o assegurar opera o segura e impedir isto de aquecer demais n o devem ser bloqueadas estas aberturas ou devem ser cobertas Nunca empurre objetos de qualquer am vel por quaisquer das aberturas de ventila o Nunca derrame qualquer l quido na unidade e Nunca prenda amplificador de poder auditivo produz diretamente a quaisquer dos conectores da unidade Prevenir choque ou perigo de inc ndio n o exponha a unidade para chover ou umidade ou opera isto onde ser exposto a umidade N o tente operar a unidade se foi derrubado estragado exposto a l quidos ou se exibe uma mudan a distinta em desempenho que indica a necessidade por servi o Esta unidade s deveria ser aberta atrav s de pessoal de servi o qualificado Removendo coberturas o expor o a voltagens perigosas Este tri ngulo que se aparece em seu componente o alerta presen a de uninsulated voltagem perigosa dentro do enclosure voltage que pode ser suficiente para constituir um risco de choque importantes e instru es de manuten o nesta literatura i Este tri ngulo que se aparece em seu componente o alerta a operando acompanhante vi Introduction DEUTSCH WICHTIGE SICHERHEITSANWEISUNGEN Heben Sie sich diese Sicherheitsanwe
138. ods of time Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as when a power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped To reduce the risk of fire or electric shock do not expose this apparatus to rain or moisture This triangle which appears on your component This triangle which appears on your component alerts you to the presence of uninsulated C AUTI ON alerts you to important operating and dangerous voltage inside the enclosure maintenance instructions in this voltage that may be sufficient to RISK OF ELECTRIC SHOCK accompanying literature constitute a risk of shock DO NOT OPEN Refer to the manufacturer s operating instructions for power requirements Be advised that different operating voltages may require the use of a different line cord and or attachment plug Do not install the unit in an unventilated rack or directly above heat producing equipment such as power amplifiers Observe the maximum ambient operating temperature listed in the product specification Never attach audio power amplifier outputs directly to any of the unit s connectors This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of FCC Rules These limits are design
139. of subwoofers being used When set to STEREO low frequencies from the front left center side left and rear left channels are combined and sent to the SUBWOOFER L output Low frequencies from the front right center side right and rear right are combined and set to the SUBWOOFER R output When set to NONE low frequencies from the FRONT L R CENTER SIDE L R and REAR L R outputs will not be passed to the SUBWOOFER L R ouputs and will be filtered at the lowest crossover setting selected SUB XOVER FULL 30Hz to 120Hz THX 80Hz The SUB XOVER parameter sets the crossover setting for the MAIN AUDIO OUTPUTS labelled SUB L R When set to FULL the unit sends a full range audio signal to the SUB L R outputs When set to a numerical crossover setting the unit activates a crossover at the selected frequency Choose the setting that matches the lowest crossover setting in the system See pages 3 18 and 3 19 for more information about crossover settings 3 22 SDP 40 The SETUP Menu MAIN MENU gt SETUP SPEAKER SETUP CUSTOM SETUP MODE ADJUST INPUTS CUSTOM SETUP FRONT L R 80Hz AUDIO CONTROLS SYNTHESIS 7CH SETUP CENTER 80Hz REAR PANEL CONFIG SPEAKER DISTANCES SIDE L R 80Hz DISPLAYS LEVELS CALIBRATION REAR L R 80Hz VOLUME CONTROLS 1 Pe SUB L R MONO TRIGGERS NU A SUB XOVER 80Hz LOCK OPTIONS x o LFE BS OFF Gs 0 p LFE ON OFF For example LFE is set to O
140. on trol The remote control requires two AA batteries that must be changed on a regular basis When the batteries are low on power the remote control will enter a low voltage condition that prevents it from operating the unit Operation will be restored when new batteries are installed COMMAND BANK SELECTION The four remote control command banks can be accessed by pressing the MAIN ZONE REC or SHIFT buttons Each button accesses a separate bank of commands until another bank is selected Pressing a bank selection button instructs the unit to engage the selected command bank Command bank selection buttons themselves do not send commands to the unit The unit indicates the last remote control command bank from which it received a command in the top right corner of the on screen display provided the REMOTE STATE parameter on the ON SCREEN DISPLAY menu is set to ON see page 3 32 A yellow Z will appear when a command from the ZONE bank was received last A red R will appear when a command from the REC bank was received last A blue S will appear when a command from the SHIFT bank was received last Nothing will appear when a command from the MAIN bank was received last The chart that begins on the next page explains the functions performed by remote control buttons when each command bank is active Note The MAIN ZONE REC or SHIFT buttons should be pressed and released to access their corresponding command banks Do not ho
141. on screen display remains on at all times When set to 2 SECONDS the on screen display will appear for two seconds when the unit receives a command or the input type changes When set to ALWAYS OFF the on screen display remains off at all times POSITION TOP CENTER BOTTOM POSITION controls the vertical position of the two line status see page 1 5 on the display device When set to TOP the two line sta tus appears near the top of the display device screen When set to CENTER the two line status is centered on the display device screen This setting is recommended when the top and bottom of the on screen display appears cropped not visible When set to BOTTOM the two line status appears near the bottom of the display device screen The SETUP Menu JBL ON SCREEN DISPLAY continued FRONT PANEL DISPLAY 2 FORMAT NTSC PAL SECAM The FORMAT parameter has three settings NTSC PAL and Default SECAM These settings make the video switcher and on screen Parameter Value Values dis i i 5 2 e 2 a p STATUS ALWAYS ON ALWAYS 2 SECONDS display device user guide to determine the correct setting ALWAYS OFF BRIGHTNESS 75 100 75 50 25 BACKGROUND ON OFF BACKGROUND activates and deactivates the menu background STATUS ALWAYS ON 2 SECONDS ALWAYS OFF When set to ON the menu appears over a solid blue or grey background When set to OFF the menu appears over the incoming video signal Setting this par
142. one 2 and the Record Zone will provide downmix a 2 channel version of multi channel digital audio only when using the same input that is selected in the Main Zone e Use caution when switching from a Dolby Digital input type to a dts ES input type in the Record Zone A loud brief noise may occur Audio will mute for up to 2 seconds when The same input is selected in the Main Zone that is already selected in Zone 2 or the Record Zone Likewise when the input is deselected in the Main Zone The same input is selected in Zone 2 or the Record Zone that is already selected in the Main Zone Likewise when the input is deselected in Zone 2 or the Record Zone When the 5 1 BYPASS listening mode is selected for the Main Zone the same input can be utilized by Zone 2 or the Record Zone However only the FRONT L R input signals will be available Basic Operation UNDERSTANDING LISTENING MODE SELECTION There are three different methods of selecting listening modes in the Main Zone e The INPUT SETUP Menu e Mode up and down buttons on the front panel or the MODE buttons on the remote control The Mode Family Selection Buttons on the remote control Listening mode selection only applies to the Main Zone INPUT SETUP MENU This type of listening mode selection occurs each time a listening mode is changed in the INPUT SETUP menu and each time an input is selected using the input selection buttons on the
143. pparat m kun bnes af fagfolk Hvis d kslet tages af uds ttes man for livsfarlig h jsp nding Denne m rkat p komponenten advarer om uisoleret farlig sp nding AN i apparatet h j nok til at give elektrisk st d Denne m rkat p komponenten advarer om vigtig driftsog vedlige AN holdsinformation i den tilh rende litteratur SUOMI T RKEIT TURVALLISUUSOHJEITA S ilyt n m ohjeet tulevaa k ytt varten Seuraa kaikkia yksikk n merkittyj ohjeita ja varoituksia e K yt aina oikeaa verkkoj nnitett Tehovaatimukset selvi v t valmistajan k ytt ohjeista Huomaa ett eri k ytt j nnitteet saattavat vaatia toisenlaisen verkkojohdon ja tai pistokkeen k yt n Ala asenna yksikk telineeseen jossa ei ole tuuletusta tai v litt m sti l mp tuottavien laitteiden esim tehovahvistimien yl puolelle Ymp rist n l mp tila k yt ss ei saa ylitt tuotespesifikaation maksimilampotilaa e Kotelo on varustettu tuuletusreiill ja aukoilla Luotettavan toiminnan varmistamiseksi ja ylilampenemisen v ltt miseksi n it aukkoja ei saa sulkea tai peitt Mit n esineit ei saa ty nt tuuletusaukkoihin Mit n nesteit ei saa kaataa yksikk n e Tuote on varustettu 3 johtimisella maadoitetulla verkkopistokkeella T m on turvallisuustoiminne eik sit saa poistaa e Ala kytke audiotehovahvistimen l ht j suoraan mihink n yksik n liittimeen e S hk iskun
144. ppareil e Branchez uniquements sur un r seau de tension indiqu e Consultez le manuel d instruction du fabriquant pour les sp cifications de courant N oubliez pas que diff rentes tensions peuvent n cessiter l utilisation de cables et ou de fiches de connexion diff rents N installez pas l appareil en un compartiment non a r ou directement au dessus d quipements g n rateurs de chaleur tels qu amplificateurs de courants d passez pas la temp rature ambiante maximale de fonctionnement indiqu e dans les sp cifications du produit Des fentes et ouvertures sont pr vues dans le boitier pour l a ration Pour assurer le bon fonctionnement et pour pr venir l chauffement ces ouvertures ne doivent pas tre couvertes ou bloqu es N ins rez pas d objets dans les fentes d a ration Emp chez tout liquide de se r pandre sur l appareil Ce produit est muni d une fiche trois fils pour la mise terre Ceci est une mesure de s curit et ne doit pas tre contrari e Ne connectez jamais d amplificateurs audio directement aux connecteurs de l appareil Pour emp cher les chocs lectriques et le danger d incendie vitez d exposer l appareil la pluie ou l humidit et ne le mettez pas en marche en un endroit o il serait expos aux claboussures d eau N essayez pas de faire fonctionner l appareil s il est tomb terre a t endommang expos un liquide ou si vous observez des d
145. puts and 3 independent zones Beyond the standard 5 1 channel outputs the unit features stereo rear and stereo subwoofer outputs Additionally the SDP 40 provides balanced audio outputs for all Main Zone and Zone 2 outputs Inside and out the unit is designed with an eye toward the future The rear panel has stereo auxiliary outputs to provide more audio channels and a removable access plate to accommodate connectors for new technologies Inside three expansion slots are available for future upgrades The system software can be upgraded in the field using the RS 232 port The SDP 40 features LOGIC7 technology LOGIC7 creates 7 1 channel output from any input signals except mono input signals Unlike many decoders LOGIC7 is compatible with most input signals and requires no special encoding Because the improvement it provides is clearly audible LOGIC7 is widely recognized as the finest surround decoder available Dolby Digital THX Surround EX dts dts ES and Dolby Pro Logic are also included THX certification guarantees that specifications meet the highest standards set forth by Lucasfilm s Home THX division Four 32 bit DSP engines provide enormous processing power Custom algorithms process 96kHz 24 bit audio in all listening modes A fifth processor the Crystal 49326 Audio DSP decodes multi channel compressed audio data sources Three expansion slots make it possible to more than quadruple available processing powe
146. r Analog sources are processed at 96kHz Digital sources use a two stage phase lock loop for extremely low intrinsic jitter with high jitter rejection Each MAIN AUDIO OUTPUT incorporates 24 bit 192kHz digital to analog converters operating in dual differential mode to ensure the highest quality performance There are two broadcast quality video switchers The ultra wide bandwidth component video switcher accepts any analog component or RGB video input type The S and composite video switcher accommodates high quality NTSC PAL or SECAM video input types Input configuration allows any source to be assigned to any input The unit will automatically switch between digital and analog sources The intuitive user interface with color on screen display makes it easy to configure the unit Three subwoofer outputs and sophisticated routing provide intelligent bass management With its unique combination of power flexibility and expandability the SDP 40 is equipped for the needs of today and the demands of tomorrow 40 Getting Started HIGHLIGHTS 12 channels 12 configurable inputs 3 zones 13 digital audio inputs including 1 AES EBU input 3 subwoofer outputs 2 auxiliary outputs for future expansion Dual 24 bit 192kHz digital to analog converters for all MAIN AUDIO OUTPUTS 5 1 channel analog input Analog bypass option 5 1 channel and stereo inputs Auto switching between digital and analog connectors 4 compon
147. rameters When switching from AUTO to MANUAL adjustment the INPUT GAIN parameter will continue to reflect the last AUTO setting until the MANUAL setting is adjusted The level meters in the lower left corner indicate fluctuating input levels in the left L and right R channels These meters indicate signal levels for the selected input whether the input signal is analog or digital For example if the input signal is digital only the level meters will indicate the digital input signal levels These level meters appear in combinations of green yellow and red on the blue screen background Green indicates normal input levels yellow indicates the onset of overload and red indicates overload The yellow arrow to the right of each bar indicates the current input peak level The INPUT GAIN parameter also shows the current input level whether AUTO or MANUAL is selected 3 7 The SETUP Menu JBL MAIN MENU MODE ADJUST AUDIO CONTROLS SETUP SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGERS LOCK OPTIONS INPUT SETUP DVD2 LD TV SAT VCR CD PVR GAME TAPE TUNER AUX DVD1 INPUT SETUP NAME DVD1 DIGITAL IN COAX 1 ANALOG IN NONE ANLG IN LVL AUTO COMPONENT IN 1 2 CH L7 FILM OO D 5 1 L7 FILM mes dts L7 FILM MAIN ADVANCED ZONE2 ADVANCED RECORD ADVANCED DVD1 is used as an example in this illustration and will continue
148. re information An alphabetical listing of parameter descriptions begins on page 5 20 and sense of envelopment of the listening space e Provides remarkable improvement compared to other decoders e Recommended for 5 1 and 6 1 channel dts ES film sources even when only one pair of surround speakers is selected e The unit will automatically activate ES decoding when dts ES input type is identified Default Parameter Value Values VOCAL ENHANCE 0 0dB 0 0 3 0dB 6 0dB 5 SPKR ENHANCE OFF ON OFF BASS ENHANCE OFF ON OFF RE EQUALIZER ON ON OFF REAR DLY OFFSET 15ms 0 to 30ms LFE MIX 0 0dB 10 0 to 0 0dB OUTPUT LEVELS See page 5 17 for more information CUSTOM See page 5 17 for more information An alphabetical listing of parameter descriptions begins on page 5 20 The MODE ADJUST Menu JBL dts ES LOGIC7 Music MODE ADJUST A proprietary Lexicon mode e Designed for playback of 5 1 and 6 1 channel dts ES music sources e Based on dts ES LOGIC7 FILM but specifically tailored for music sources e Recommended for 5 1 and 6 1 channel dts ES music sources even when only one pair of surround speakers is selected e The unit will automatically activate ES decoding when a dts ES input type is identified Default Parameter Value Values VOCAL ENHANCE 0 0dB 0 0 3 0dB 6 0dB 5 SPKR ENHANCE OFF ON OFF BASS ENHANCE OFF ON OFF REAR
149. s as a step in a menu path any other input may be substituted INPUT SETUP The unit has 12 inputs each of which can be associated with any of its 13 digital audio 8 analog audio and 17 video input connectors Selecting the INPUTS option on the SETUP menu prompts the selection of the desired input for configuration Selecting an input accesses the INPUT SETUP menu The DVD1 INPUT SETUP menu is used as an example above and will continue to be used as an example throughout this section The parameters on the left side of the INPUT SETUP menu are identical regardless of which input is selected The values on the right side of the menu are adjustable See page A 6 for an illustration of all INPUT SETUP menus 3 3 The SETUP Menu JBL MAIN MENU gt SETUP gt INPUT SETUP gt DVD1 INPUT SETUP gt DVD1 INPUT NAME MODE ADJUST NAME DVD1 EDIT INPUT NAME AUDIO CONTROLS SPEAKERS DVD2 DIGITAL IN COAX 1 RESTORE DEFAULT NAME REAR PANEL CONFIG LD ANALOG IN NONE DISPLAYS TV ANLG IN LVL AUTO VOLUME CONTROLS SAT VIDEO IN S VIDEO 1 TRIGGERS VCR COMPONENT IN 1 LOCK OPTIONS CD 2 CH L7 FILM PVR Do D 5 1 L7 FILM GAME TAES dts L7 FILM TAPE MAIN ADVANCED TUNER ZONE2 ADVANCED AUX RECORD ADVANCED DVD1 is used as an example in this illustration and will continue to be used as an example throughout this section Whenever DVD1 appears as a step in a menu
150. setup that requires THX certified loud speakers use the SYNTHESIS 7CH SETUP menu see page 3 24 Default Parameter Value Values FRONT L R 40Hz FULL 30Hz to 120Hz THX 80Hz CENTER 60Hz FULL 30Hz to 120Hz THX 80Hz NONE SIDE L R 60Hz FULL 30Hz to 120Hz THX 80Hz NONE REAR L R 60Hz FULL 30Hz to 120Hz THX 80Hz NONE SUB L R MONO MONO STEREO NONE SUB XOVER 40Hz FULL 30Hz to 120Hz THX 80Hz LFE OFF ON OFF Determining Crossover Settings The CUSTOM SETUP menu allows different crossover points to be set for the following MAIN AUDIO OUTPUTS FRONT L R CENTER SIDE L R REAR L R and SUBWOOFER L R Crossover points can be set in 10Hz increments within a 30 to 120Hz range All crossover settings activate a 24dB per octave filter with the exception of THX 80Hz which activates a 12dB per octave filter The graphs on the next page illustrate the frequency response of the crossover settings For each output select the crossover setting closest to the low frequency rating of the corresponding speaker For the SUBWOOFER L R outputs select the crossover setting that matches the lowest setting of the other speakers in the system Crossover settings determine how the unit redirects low frequency signals In general low frequencies will be redirected from the outputs with the highest crossover setting to the outputs with the lowest crossover setting Remaining low frequencies below the lowest crossover setting w
151. stereo music sources e Identical to DOLBY PRO LOGIC Il except specifically tailored for stereo music sources Default Parameter Values Default Value PANORAMA OFF ON OFF CTR WIDTH 3 MIN 1 to 6 MAX DIMENSION NEUTRAL FRONT NEUTRAL REAR SURROUND DLY 5 0 to 15ms OUTPUT LEVELS See page 5 17 for more information CUSTOM See page 5 17 for more information An alphabetical listing of parameter descriptions begins on page 5 20 DOLBY PRO LOGIC AAA gt Designed for playback of Dolby Surround encoded sources e Decodes four channels from Dolby Surround encoded input types e Utilizes a mono surround channel with a high frequency rolloff above 7kHz e Available for comparison purposes particularly with the LOGIC7 FILM and DOLBY PRO LOGIC II listening modes Default Parameter Value Values OUTPUT LEVELS See page 5 17 for more information CUSTOM See page 5 17 for more information An alphabetical listing of parameter descriptions begins on page 5 20 The MODE ADJUST Menu JBL 2 CHANNEL e Designed for playback of stereo sources e Sends stereo sources to the FRONT L R outputs only e Available for audio purists and for comparison purposes Default Parameter Values Default Value SUB L R LVL 0dB OFF 30 to 12dB CUSTOM See page 5 17 for more information An alphabetical listing of parameter descriptions begins on page 5 20 PARTY 2 e Designed for playb
152. t med ventilasjons pninger For at apparatet skal v re p litelig i bruk og ikke overopphetes m disse pningene ikke blokkeres eller tildekkes Stikk aldri noe inn i ventilasjons pningene og pass p at det aldri sgles noen form for vaeske p apparatet e Dette apparatet er utstyrt med et jordet st psel Dette er sikkerhetsforanstaltning som ikke forandres Utgangsplugger fra audioforsterkere skal aldri koples direkte til apparatet e Unng brannfare og elektrisk stat ved s rge for at apparatet ikke utsettes for regn eller fuktighet og ikke anvendes i naerheten av vann e Apparatet skal ikke brukes hvis det har utsatt for stat er skadet eller blitt vatt eller hvis endringer i ytelsen tyder at det trenger service Dette apparatet skal kun apnes av fagfolk Hvis dekselet fjernes utsettes man for livsfarlig h yspenning at det finnes uisolert farlig spenning inne i kabinettet h y nok til Komponenten er merket med denne trekanten som er advarsel om utgjere en fare for elektrisk stot Komponenten er merket med denne trekanten som betyr at den AN tilh rende litteraturen inneholder viktige opplysninger om drift og ved SVENSKA VIKTIGA S KERHETSF RESKRIFTER Spara dessa f reskrifter f r framtida bruk e F lj alla anvisningar och varningar som anges p enheten e Anv nd alltid r tt n tsp nning Se tillverkarens bruksanvisningar f r information om effektkrav M rkv
153. t occurs in a movie theater as sound travels from the front speakers to the listeners Most films are mixed for movie theaters and may sound too bright when played back in a home theater without re equalization Timbre matching helps minimize the timbre differences between the front and side channels which results in smoother sound movements between these channels Recommended for home theaters with a THX certified speaker system Default Parameter Value Values RE EQUALIZER ON ON OFF OUTPUT LEVELS See page 5 17 for more information CUSTOM See page 5 17 for more information An alphabetical listing of parameter descriptions begins on page 5 20 DOLBY PRO LOGIC II MODE ADJUST DOPRO LOGIC Il Designed for playback of Dolby Surround encoded sources e Decodes five channels from Dolby Surround encoded input types e Similar to DOLBY PRO LOGIC except it utilizes full frequency stereo surround channels to realistically increase the perceived width of the listening space e Provides impressive enhancement compared to DOLBY PRO LOGIC e Appropriate for Dolby Surround encoded film sources Default Parameter Value Values OUTPUT LEVELS See page 5 17 for more information CUSTOM See page 5 17 for more information An alphabetical listing of parameter descriptions begins on page 5 20 40 The MODE ADJUST Menu DOLBY PRO LOGIC Il MUSIC AAA gt 0 PL II MUSIC e Designed for playback of
154. the input for the zone Reserved for future expansion Selects the input for the zone Increases BASS in 0 5dB increments Selects the input for the zone Selects the input for the zone Increases TREBLE in 0 5dB increments Increases TILT EQ 0 2dB increments Selects the input for the zone Decreases BASS in 0 5dB increments Selects the input for the zone Decreases TREBLE in 0 5dB increments Selects the input for the zone Decreases TILT EQ in 0 2dB increments See Section 4 for more information about these AUDIO CONTROLS menu parameters Basic Operation JBL Toggles the FRONT PANEL DISPLAY menu STATUS parameter between ALWAYS OFF and its current setting see page 3 32 Sets Zone 2 volume to 15 Sets Record Zone volume to 15 Sets Main Zone volume to 15 BLUE Toggles the ON SCREEN DISPLAY menu BACKGROUND parameter between ON and OFF see page 3 32 Sets Zone 2 volume to 30dB Sets Record Zone volume to 30dB Sets Main Zone volume to 30dB Toggles the ON SCREEN DISPLAY menu STATUS parameter between ALWAYS OFF and its current setting see page 3 31 Reserved for future expansion Reserved for future expansion Sets BASS TREBLE and TILT EQ to 0 0dB See Section 4 for more information about these AUDIO CONTROLS menu parameters 2 10 40
155. tons 2 3 Zone 2 2 3 Zones Understanding the 2 15 SYNTHESIS LIMITED WARRANTY The following JBL Synthesis products are warranted for 2 years from the date of original purchase Amplifiers Equalizers and Surround Sound Processors Who is protected by this warranty Your JBL warranty protects the original owner and all subsequent owners so long as the original bill of sale is presented when warranty service is requested What is covered by the JBL warranty Your JBL warranty covers all defects in the material and workmanship with the following specified exceptions 1 Damage caused by accident unreasonable use or neglect including the lack of reasonable and necessary maintenance 2 Damage caused by improper installation or adjustment 3 Damage occurring during shipment claims must be presented to the carrier 4 Damage to or deterioration of any accessory or decorative surface 5 Damage resulting from failure to follow instructions contained in your user guide 6 Damage resulting from the performance of repairs by someone other than an authorized JBL warranty station 7 Any JBL unit on which the serial number has been effaced modified or removed 8 Units which have been altered or modified in design appearance or construction 9 Products sold on an as is or final sale basis This warranty covers only the actual defects within the product itse
156. un eventuale surriscaldamento queste aperture non vanno ostruite o coperte in nessun modo Evitare in tutti i casi di inserire oggetti di qualsiasi genere attraverso le fessure di ventilazione Non versare mai del liquido di nessun tipo sull unit Questo prodotto viene fornito con una spina a 3 fili con massa Tale dispositivo di sicurezza non va eliminato e Evitare sempre di collegare le uscite dell amplificatore audio direttamente ai connettori dell unit Per prevenire il pericolo di folgorazione e di incendio non esporre l unit alla pioggia o ad un umidit eccessiva evitare di adoperare l unit dove potrebbe entrare in contatto con acqua e Evitare di adoperare l unit se la stessa stata urtata violentemente se ha subito un danno se stata esposta ad un liquido o in caso di un evidente cambiamento delle prestazioni che indichi la necessit di un intervento di assistenza tecnica Ogniintervento sull unit va eseguito esclusivamente da personale qualificato La rimozione della copertura comporta l esposizione al pericolo di folgorazione di tensioni pericolose non isolate all interno della copertura tali Il presente triangolo impresso sul componente avverte della presenza tensioni rappresentano un pericolo di folgorazione presenza nella documentazione allegata di importanti istruzioni relative Il presente triangolo impresso sul componente avverte l utente della al funzionamento ed alla manutenzione
157. ustomized name that scrolls across the on screen and front panel displays when the unit is powered on provided the CUSTOM parameter is set to ON Selecting EDIT CUSTOM NAME accesses the pulldown menu pictured at the right Use the up and down MENU arrows to change the character above the Up to 13 DISPLAY SETUP ON SCREEN DISPLAY FRONT PANEL DISPLAY AN SYNC DELAY OFF CUSTOM NAME OFF EDIT CUSTOM NAME SDP 40 BUTTONS TO EDIT UP TO 13 CHARACTERS BUTTON TO ADVANCE characters including blank spaces can be entered Use the right MENU arrow to advance to the next character The will automatically wrap to the first character space after the thirteenth character space is passed When finished press the left MENU arrow to close the pulldown menu 3 33 The SETUP Menu JBL MAIN MENU SETUP gt VOLUME CONTROL SETUP MODE ADJUST INPUTS MAIN PWR ON FULL AUDIO CONTROLS SPEAKERS MUTE LEVEL 30dB SETUP REAR PANEL CONFIG ZONE PWR ON 30dB DISPLAYS REC PWR ON 30dB VOLUME CONTROLS TRIGGERS LOCK OPTIONS VOLUME CONTROL SETUP Default Parameter Value Values MAIN PWR ON 30dB LAST LVL 80 to 6dB MUTE LEVEL FULL FULL 40dB 30dB 20dB 10dB ZONE PWR ON 30dB LAST LVL 80 to REC PWR ON 30dB LAST LVL 80 to MAIN PWR ON LAST LVL 80 to 6dB MAIN PWR ON establishes the volume level that will be active in the Main Zon
158. utton on the remote control will also display the two line status The two line status that appears depends on which remote control command bank is active see page 2 8 The two line status shows the current input name top left the current listening mode name bottom left the current input type top center and the current volume level right RESTORING FACTORY DEFAULT SETTINGS The procedure below outlines the process to restore factory default settings Before performing these steps record custom settings on the installation worksheet see page A 12 All parameters will be reset to their factory default value This procedure should be performed before setup begins To restore factory default settings 1 Record user defined settings on the installation worksheet see page 12 2 If the unit is on place it into standby by pressing the amp standby button on the remote control If the unit is in standby skip ahead to Step 3 Power the unit on by pressing the standby button on the remote control Quickly press and hold the MUTE button on the remote control until the following hidden menu appears FACTORY SETTINGS EXIT RESTORE DEFAULTS The MUTE button must be pressed within 3s of powering the unit on If the message MUTE ON appears in the top left corner of the screen when the MUTE button is pressed too much time has passed Begin again with Step 2 Use the up and down MENU arrows t
159. z 70Hz 70Hz 70Hz 70Hz 80Hz 80Hz 80Hz 80Hz 80Hz THX 80Hz THX 80Hz THX 80Hz THX 80Hz THX 80Hz 90Hz 90Hz 90Hz 90Hz 90Hz 100Hz 100Hz 100Hz 100Hz 100Hz 110Hz 110Hz 110Hz 110Hz 110Hz 120Hz 120Hz 120Hz 120Hz 120Hz NONE NONE NONE A 8 SDP 40 Appendix LEVELS CALIBRATION TRIGGER SETUP TRIGGER SETUP INTERNAL NOISE TEST TRIGGER 1 PROGRAM REMOTE CONTROL OFF DACS CALIBRATION TRIGGER 2 PROGRAM DVD1 OFF SURE Continued from page A 5 MS i Continued from page A 8 SAT OFF VCR OFF INTERNAL NOISE SPEAKER LEVEL ADJUST SUB LIMITERS CD OFF PVR OFF ICAUTION FRONT LEFT 40 0dB CAL NOISE ON GAME OFF HIGH AUDIO LEVELS CENTER 40 0dB L R LIMITER OFF TAPE OFF FRONT RIGHT 40 0dB L R LIMIT ADJ 100dB TUNER OFF SIDE RIGHT 40 0dB LFE LIMITER OFF AUX OFF REAR RIGHT 40 0dB LFE LIMIT ADJ 100dB ZONE2 INPUTS OFF EEE REAR LEFT 0 0dB RECORD INPUTS OFF SIDE LEFT 0 0dB ICAUTION 14 FILM ON MEET 0 09B SUB MONO 40 0dB HIGH AUDIO LEVELS p TV ON CENTER 0 0dB FRONT RIGHT 30048 SUB RIGHT 0 0dB 191 MUSIC ON SIDE RIGHT LFE SUB 40 0dB PL THX ON 40 0dB REAR RIGHT 000 PRO LOGIC Il ON BEAR LEST DACS CALIBRATION DO PL Il MUSIC ON SUE When SUB L R is set to PRO LOGIC ON SUB MONO 0 0dB STEREO or NONE see page 2 CHANNEL OFF SEI

Lexicon SDP-40 User's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents