Leviton RZCZ1 User's Manual
Contents
1. 5 8 1 6 cm z Strip Gage Cut wire here if necessary Side Wire Connection Side wire terminals accept 14 AWG solid wire copper only Back wire openings use 14 12 AWG solid wire copper only e Make sure that the ends of the wires from the wall box are straight cut if necessary screws or through backwire openings Choose appropriate wire measure bare Back Wire either hole may be used WARNINGS AND CAUTIONS i al Compatible with Waa enabled products y N S 7 e Can call up four 4 zone ON OFF with advanced Programmer Remote see RZCPG e Disconnect power at circuit breaker or fuse when servicing installing or removing fixture e Use this device only with copper or copper clad wire With aluminum wire use only devices marked CO ALR or CU AL Step 4 Wiring Application 4 Zone Controlller Hot Black Green f Ground E Line 120VAC 60Hz Neutral White WIRING SWITCH Connect wires per WIRING DIAGRAM as follows e Green or bare copper wire in wall box to Green terminal screw e Line Hot wall box wire to terminal screw marked BK e Line Neutral wall box wire to terminal screw marked WH Step 5 Testing your 4 Zone Controller prior to mounting in wall box e Position all wires to provide room in outlet wall box for device e Ensure that the word TOP is facing up on device strap e Partially screw in2. dim bright for up to 4 Zones Area e ON OFF LED e Two way communication e RF reliability e Ease of installation No new wiring e Compatible with other Z Wave enabled devices Tools needed to install your 4 Zone Controller Pliers Ruler Slotted Phillips Screwdriver Pencil Electrical Tape Cutters Changing the color of your 4 Zone Controller Your 4 Zone controller includes three color options The controller ships with the White frame attached To change color of frame proceed as follows F E i Push in Line up tabs side at tab and press in to release side to attach After frame is removed remove existing push buttons by pressing out buttons from back of frame and replace them with desired color change push buttons by pressing in from front of frame To make IR capable use new DIM BRIGHT button with IR window INSTALLING YOUR 4 ZONE CONTROLLER NOTE Use check boxes y when Steps are completed Step 1 E WARNING TO AVOID FIRE SHOCK OR DEATH TURN OFF POWER at circuit breaker or fuse and test that power is off before wiring EY Identifying your wiring application most common NOTE If the wiring in your wall box does not resemble this configuration consult a qualified electrician 1 Line Hot 2 Neutral 3 Ground Step 3 Preparing and connecting wires This 4 Zone controller can be wired using side wire terminal stripping specifications accordingly
3. to correct such defects by repair or replacement at its option if within such five year period the product is returned prepaid with proof of purchase date and a description of the problem to Leviton Manufacturing Co Inc Att Quality Assurance Department 59 25 Little Neck Parkway Little Neck New York 11362 2591 This warranty excludes and there is disclaimed liability for labor for removal of this product or reinstallation This warranty is void if this product is installed improperly or in an improper environment overloaded misused opened abused or altered in any manner or is not used under normal operating conditions or not in accordance with any labels or instructions There are no other or implied warranties of any kind including merchantability and fitness for a particular purpose but if any implied warranty is required by the applicable jurisdiction the duration of any such implied warranty including merchantability and fitness for a particular purpose is limited to five years Leviton is not liable for incidental indirect special or consequential damages including without limitation damage to or loss of use of any equipment lost sales or profits or delay or failure to perform this warranty obligation The remedies provided herein are the exclusive remedies under this warranty whether based on contract tort or otherwise
4. Area is ON Turn OFF from ON position Press right side of button Turns all lights in Zone Area OFF LED turns OFF Dim Bright Press left side of Dim Bright button Lights in last activated Zone Area will dim Press right side of Dim Bright button Lights in last activated Zone Area will brighten NOTE Controller will only Dim Bright devices located within the Radio Frequency range NOTE LED will be lit Green if any one load in the associated Area is ON LED will be OFF when all loads are turned OFF If there is a power outage when the power is restored the lights will return to the last setting before the power interruption Cleaning Clean with a damp cloth DO NOT use chemical cleaners Push Buttons Locator LED Dim Bright Button TROUBLESHOOTING e Locator LED on controller does not turn ON Circuit breaker or fuse has tripped If 4 Zone controller is powered up and LED does not turn ON check wiring e Zone Controller does not operate lights Check association Ensure that controller was properly updated e If LED turns solid red Check association Ensure that each device in the network is with in 70 ft 21 m of another device For additional information contact Leviton s Techline at 1 800 824 3005 or visit Leviton s website at www ViziaRF com U S amp Foreign Patents Pending Copyright 2006 Leviton Manufacturing Co Inc All Rights Including Trade Dress Rights Reser
5. Z LEVITON Building A Connected World DI 000 RZCZ4 00A X1 WARNINGS AND CAUTIONS ON OFF LED for remote load control 4 Zone Controller Cat No RZCZ4 120VAC 60Hz INSTALLATION INSTRUCTIONS To be installed and or used in accordance with appropriate electrical codes and regulations If you are unsure about any part of these instructions consult a qualified electrician Vizia RF RZCZ4 remote does not control the load but provides scene applications to operate with Vizia RF switches Recommended minimum wall box depth is 2 1 2 INTRODUCTION Leviton s Vizia RF components are designed to communicate with each other via Radio Frequency RF to provide remote control of your lighting Using RF technology allows Leviton to provide the greatest signal integrity possible Each module in Leviton s Vizia RF component line is a Z Wave enabled device In a Z Wave network each device is designed to act as a router These routers will re transmit the RF signal from one device to another until the intended device is reached This ensures that the signal is received by its intended device by routing the signal around obstacles and radio dead spots The 4 Zone Controller is compatible with any Z Wave enabled network regardless of the manufacturer and can also be used with other devices displaying the Z Wave logo e This is a Z Wave Controller e Zone Area control without traveler wires e Can control ON OFF
6. e network NOTE Only one device may be included at any time E The Primary Programmer Remote will assign a Home ID Node ID and Name for this device NOTE This information will be stored in the Programmer Remote to be used for future reference NOTE You may name or edit the node of this device at this time F The 4 Zone controller is now installed in the network G After all devices are included into the network the controller must be updated to allow proper network function To update controller proceed as follows e f using a non Leviton Programmer Remote refer to the Programmer Remote instruction sheet for updating controller e If using Leviton Z Wave Programmer Remote Cat No RZCPG press the Menu button and scroll down to System Setup Press the center button to select System Setup Menu Press the center button to select Network Press the center button to select Update cntrl When prompted press desired button on 4 Zone controller e Wait until the RZCPG Programmer Remote confirms completion Update is done NOTE If the 4 Zone controller has been successfully Included in the network and the user tries to Include it again without first excluding it from the network the controller will retain the first node ID it had received and ignore the second Menu Button Center Button Programmer Remote Cat No RZCPG Including 4 Zone Controller into Z Wave Network Step 6 cont d Prog
7. mounting screws in wall box mounting holes NOTE Dress wires with a bend as shown in diagram in order to relieve stress when mounting device e Restore power at circuit breaker or fuse LED should turn ON when any button is pressed If LED does not turn ON refer to the TROUBLESHOOTING section NOTES e If using a non Leviton Programmer Remote refer to the Programmer Remote instruction sheet 4 Zone controllers incuded into a Z Wave network must be updated after you have included all other devices A If using a Leviton Z Wave Programmer Remote Cat No RZCPG press the Menu button and scroll down to System Setup Press the center button to select System Setup Menu Press the center button to select Network Press the center button to lt Include Node gt Including 4 Zone Controller into Z Wave Network Step 6 cont d B If using RZCPG Programmer Remote you will be prompted to place 4 Zone controller into programming mode C To access Program mode press and hold the left side of buttons 1 and 3 refer to figure Wait 5 seconds until the LED turns Amber Release the button and the LED will blink Amber You are now in Programming mode NOTE If the LED on the 4 Zone controller turns solid Red while including there has been a communication error D While standing close to the 4 Zone controller approximately 2 5 ft press the center button on the Programmer Remote to lt Include gt device in th
8. nd 3 Wait approximately 5 seconds until the locator LED turns Amber and then turns solid Red Release the buttons The 4 Zone controller is now reset Once the controller is reset it will be necessary to Re Include it to a network before it can be used CAUTION SETTING A DEVICE TO A FACTORY DEFAULT DOES NOT EXCLUDE THAT DEVICE FROM A NETWORK THE EXCLUSION PROCEDURE MUST STILL BE FOLLOWED TO REMOVE THE DEVICE FROM THE PRIMARY CONTROLLER S INFORMATION TABLE FAILURE TO DO SO MAY RESULT IN SYSTEM THAT IS SLOW TO RESPOND OR MAY FAIL TO RESPOND TO SOME DEVICES Sten Device Association After inclusion process you must associate the devices to the controllers Refer to the Primary Programmer Remote instruction sheet for complete details NOTE One 1 Z Wave device can be associated to multiple controllers up to five 5 controllers maximum NOTE If using a non Leviton Programmer Remote refer to the Programmer Remote instruction sheet for associating a device Step 9 4 Zone Controller Mounting TURN OFF POWER AT CIRCUIT BREAKER OR FUSE Installation may now be completed by tightening mounting screws into wall box Attach wallplate Restore Power Restore power at circuit breaker or fuse Installation is complete OPERATION Push Button Default settings Turn ON from OFF position Press left side of button Turns all lights in Zone Area ON LED turns ON LED will blink until Zone
9. rammer Remote Cat No RZCPG NOTE Programmer Remote must be in close proximity to 4 Zone controller when including in the network Stra Excluding 4 Zone Controller from H Z Wave Network A If using a Leviton Z Wave Programmer Remote Cat No RZCPG press the Menu button and scroll down to System Setup Press the center button to select System Setup Menu Press the center button to select Network Scroll down to lt Exclude Node gt and press the center button B If using RZCPG Programmer Remote you will be prompted to place 4 Zone controller into programming mode C To access Program mode press and hold the left side of buttons 1 and 3 refer to figure Wait 5 seconds until the LED turns Amber Release the buttons and the LED will blink Amber You are now in Programming mode NOTE If the LED on the 4 Zone controller turns solid Red while excluding there has been a communication error D While standing close to the 4 Zone controller approximately 2 5 ft press the center button on the Programmer Remote to lt Exclude gt device in the network Factory Default If your 4 Zone controller is not responding or you are unable to control it after you have tried to Include Exclude it multiple times it may be necessary to reset the 4 Zone controller to its original factory settings To accomplish this proceed as follows e On the 4 Zone controller refer to figure press and hold the left side of buttons 1 a
10. ved FCC COMPLIANCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B Digital Device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment OFF and ON the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving Antenna e Increase the separation between the equipment and the receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio tv technician for help NOTES DI 000 RZCZ4 00A X1 LIMITED 5 YEAR WARRANTY AND EXCLUSIONS Leviton warrants to the original consumer purchaser and not for the benefit of anyone else that this product at the time of its sale by Leviton is free of defects in materials and workmanship under normal and proper use for five years from the purchase date Leviton s only obligation is
Download Pdf Manuals
Related Search