Lennox Hearth EDV-40 User's Manual
Contents
1. 750 200M LENNOX HEARTH PRODUCTS REV B 06 2006 LENNOX HEARTH PRODUCTS KITS AND ACCESSORIES DECORATIVE STYLE VIEW ARCH PANE SCREEN DOOR KITS CHARCOAL amp SATIN PEWTER INSTALLATION INSTRUCTIONS FOR DECORATIVE TALL ARCH SCREEN PANEL KITS FOR USE WITH MPB 35 40 45 MPD 35 40 45 MPB35ST MPD35ST EDV 35 40 45 SDDV 35 40 EDVST amp EBVST GAS FIREPLACES a es ara aaa i wane a asin samo Cass wen ere 13535 TAPD45SP 45 Arch Pane Satin Pewter H3537 TAPD35EC 35 Arch Pane Charcoal SDDV 35 amp EDV35 only 13539 TAPD35ESP 35 Arch Pane Satin Pewter SDDV 35 amp EDV35 only Table 1 tea boone tea booing rea vorams tea Lover Compannen Goer ea Frenor tom coverPanet tea inucionsteet Table 2 Refer to Figure 1 Read and understand all instructions and warnings in this docu ment before beginning the installation TOOLS REQUIRED 0 16 Nutdriver or Socket 1 4 Nutdriver or Socket for EDVST model only GENERAL INFORMATION These decorative screen doors are offered in two attractive finishes and fit on the face of the appliance over the glass doorframe If you encounter any problems need clarification of these instructions or are not qualified to properly install this kit contact you local distributor or dealer Note Early revisions of model EDVST and EBVST may also require a magnet mounting kit Cat No H2110 If the appliance does not have slots described i2. two 10 screws from hae the firebox bottom een m ye 7 Remove the screen doors from packaging Install them by aligning on both sides save pe hinge pins on the doors with the hinge holes on the doorframe and screws 10 Screw slide down see instructions in Figure 8 Ensure the hinge pins are fully seated onto the shoulders of the hinge holes Step 3 Install the Firebox Bottom Cover Panel 5 in Figure 1 using the existing 10 screws The bottom two holes on the cover panel align to cor Align hinge pins on the responding two holes on firebox bottom doors with the hinge holes on the doorframe and slide Figure 5b Install Firebox Cover down as shown 4 For EDV EDVST amp EBVST models reinstall modesty panel ensuring all wires are securely connected 5 Install Doorframe see Figure 6 Remove the arched doorframe from packaging Position the top of the doorframe above the top of the glass doorframe centered and approximately 1 above the top of the glass doorframe Slide down so that the hooks catch on the back of the doorframe slide between the sides of the glass door and the corner posts engaging into existing slots on fireplace Doorframe Right Corner Post ae ae a Figure 6 INSTALL DOORFRAME 6 Place the doorframe bracket in the locked position as shown in Figure 7 Figure 8 NOTE DIAGRAMS amp ILLUSTRATIONS ARE NOT TO SCALE 8 Light the appliance following instrutions on lighting
3. label in control compartment or see lighting instructions in Homeowner s Care and Operation Manual provided with appliance Note Ensure that the latch es below the door are engaged with the door s vee flange and fully closed before operating the fireplace 9 Install the lower compartment cover per instructions in Figure 9 Lower Compartment Cover _ Ss eT ki nobs Place the lower compartment cover hook behind the glass doorframe bottom flange Figure 9 INSTALL LOWER COMPARTMENT COVER 10 Re install the top louvered or radiant panel hood assemblies 11 Close both doors as shown in Figures 9 amp 10 Figure 11 COMPLETED INSTALLATION NOTE DIAGRAMS amp ILLUSTRATIONS ARE NOT TO SCALE Lennox Hearth Products reserves the right to make changes at any time without notice in design materials specifications prices and the discontinuance of colors styles and products Consult your local distributor for fireplace code information LENNOX TM Printed in U S A LENNOX HEARTH PRODUCTS 2006 HEARTH PRODUCTS 4 P N 750 200M REV B 06 2006 1110 West Taft Avenue Orange CA 92865
4. N THE FIREPLACE IS OFF AND COLD NOTE DIAGRAMS amp ILLUSTRATIONS ARE NOT TO SCALE INSTALLATION INSTRUCTIONS a Open the latch es at the bottom of the glass door assembly as shown in Figure 4 refer to Homeowners Manual 1 Remove Top and Bottom Panels a Remove the top louvered or radiant panel hood assembly by pulling b Adjust glass door so that it IS evenly spaced and aligned to the fireplace the assembly up and out see Figure 2 In instances where the radiant chassis on both sides See Figure 4 panel is used and it is framed in with tile or other approved material the hood must still be removed by firmly pulling it forward until it releases from the receiving brackets b Remove the bottom louvered or radiant panel hood assembly refer to Homeowner s Care and Operation Manual Top Flange on Glass Door c Fasten the latch es Ensure that the latch es are engaged with the door s vee flange and fully closed See Figure 4 Some models will have a modesty panel in the control compartment in front of the valve The appearance will vary from the example shown below Remove Trim Panels as shown The trim panels will be either Louvered Panels or Radiant Panels Modesty Panel Bottom Vee flange Glass Door Firebox Floor Glass Door Latch Figure 4 GLASS DOOR ADJUSTMENT ANN SS Panels Louvered Panels Figure 2 Remove Top Panel 3 Install Firebox Bottom Cover Panel For Models EDV 35 40 45 see c Re
5. move Bustles Some models have bustles as shown in Figure 3 Figure 5a For Model EDVST see Figure 5b which must be removed If applicable remove the top and bottom bustle by lifting them up and out For EDV 35 40 45 Models Only Some Models Have Bustles Bustles Lift Bustles Up And Off Figure 3 Remove Bustles Step 1 Remove 2 fire 2 Align Glass Door see Figure 4 Ensure the glass door assembly on box bottom screws the fireplace is properly aligned as follows Note Units with Modesty Panels Remove the modesty panel Step 2 Install the Firebox Bottom Cover Panel 5 in Figure 1 using the if necessary as follows Lift the modesty panel by the tab on the existing screws that were removed The top two holes on the panel align to panel s right end pull the right end of the panel away from cabinet corresponding holes on fireplace and then pull the panel diagonally out of the corner post slots on the left side of the unit Remove the modesty panel carefully so that none of the wires become loose or disconnected Figure 5a Install Firebox Cover NOTE DIAGRAMS amp ILLUSTRATIONS ARE NOT TO SCALE For EDVST Model Only Adjust Doorframe Bracket Locate the doorframe bracket on the lower front of the doorframe and lock it behind the cabinet bottom flange as shown here Doorframe Step 1 Remove the Bracket two 8 screws from the bracket screw cover on both sides Figure 7 Step 2 Remove the
6. n Step 5 to accept the hinge tabs on style view doors the tabs on the style view doorframe must be sawed off then the doorframe will be secured to the glass door assembly using 4 magnets provided in the H2110 kit kit Contents see Table 2 Figure 1 AX WARNINGS Hot Do nottouch The decorative screen doors and the glass behind the screen doors will become hot during operation and will retain v heat for a while after shutting off the appliance A pma Severe burns may result Carefully supervise m children in the same room as appliance e These decorative screen doors are NOT heat guards and are not intended to prevent burns Operate the doors by only using the door handles Avoid touching the doorframe screens or the glass enclosure if the door is opened The lower compartment cover will become hot during operation of the fireplace Use care when removing the panel to access the controls Handle the compart ment cover by grasping the two knobs mounted on the face of the cover panel Be certain to place the control compartment cover panel on a surface that is non combustible or will not be damaged by high temperatures Use care when opening doors Avoid exerting any downward pressure on the doors when they are in an open position Excessive force can cause the doors to come loose or be damaged INSTALL ONLY WHE
Download Pdf Manuals
Related Search