LaserMax Stud Sensor LMS-JMX-H User's Manual
Contents
1. ODE LASER WAVELENGTH 600 700 nm CLASS Illa LASER PRODUCT AVOID DIRECT EXPOSURE TO BEAM MANUFACTURED BY LASERMAX INC 3495 WINTON PLACE ROCHESTER NY 14623 USA Patent US 6 591 536 other patents pending 1 800 527 3703 installation guide continued 01785 0 21 REV C 6 072. ery cover screw until the battery cover J is able to rotate Rotate the battery cover J until you are able to remove the batteries Replace the batteries by inserting the negative end first The batteries positive printed side must face out Rotate the battery cover to its original orientation Tighten the battery cover screw until snug do not over tighten Confirm that the laser will now activate If the laser will not turn on retighten the screw and try again See Figures f h Remove batteries when not in use for extended periods of time to preserve battery life installation guide E LCS LMS JMX H LMS JMX NH Changing The Laser Mode Beam Selection Switch One of the unique features of the J Max Laser System is the ability to change the laser mode The J Max comes factory set for a modulated pulsed beam for higher visibility To change this setting to a continuous wave steady on beam follow these simple steps 1 Remove both Grips A amp B Switch the Beam Selection Switch on the Laser Side Plate C to the left See Figure h Reassemble as usual To return to modulated pulsed laser mode repeat steps 1 3 Right Pulsed LEFT Continuous Mode The hole at the top adjusts The hole at the side adjusts elevation vertical alignment windage horizontal alignment NOTE When installing J Max for the first time a slight shift in alignment may be noticed after firing due
3. kaSe MAA LMS JMX H LMS JMX NH Affix Laser Warning Label I onto your firearm as close to the laser as possible 2s fm DONOT REMOVE screw below cylinder LEFT GRIP RIGHT GRIP LASER SIDE PLATE GRIP SCREW SIDE PLATE SCREWS 2 BATTERIES 2 LARGE HEX WRENCH 5 64 ALIGNMENT TOOL 035 LASER WARNING LABEL BATTERY COVER Make sure your gun is unloaded Double check to verify your handgun is safe before proceeding Unscrew the mounting hardware on your existing grips in most cases this will be a single flat head screw refer to gun Owners manual for proper size and remove grips Remove the two 2 factory side plate screws Do not remove factory side plate or side plate yoke screw See Figures a amp b Place left side of revolver grip frame over Left Grip A so that the grip frame aligns with features in Left Grip A See Figure b Place Laser Side Plate C over right side of grip frame aligning it with grooves and screw holes in frame See Figure c Insert Side Plate Screws E into holes in Laser Side Plate C Tighten with the Large Hex Wrench G Do not over tighten See Figure d Position Right Grip B over Laser Sight Plate C aligning it with grooves amp screw hole Insert Grip Screw D into hole in Right Grip B and through frame Secure with flat blade screwdriver See Figure e To insert or replace batteries Using a small flat blade screwdriver loosen the batt
4. to settling Recheck alignment after your first trip to the range Reaojust if necessary You can easily fine tune your laser to accommodate any weapon platform type of ammunition or shooting distance T To sight in the laser insert Alignment Tool H into one of the holes at the top of the laser side plate C 2 Fine tune your laser alignment by slowly turning the Alignment Tool H then checking your laser position against your iron sights amp your POI Point of Impact One half turn will be roughly equal to an adjustment of two feet at twenty yards A clockwise turn lowers your elevation A clockwise turn moves your windage to the left Use of a boresighter to sight in your laser is not recommended Your POI will vary greatly depending on range and ammunition Storing Your Alignment Tool amp Batteries Your J Max laser comes with two 2 Alignment Tools H for your convenience One tool can be stored on the inside of the Left Grip A for use on the range or in the field A spare set of 357 Batteries not included can also be stored inside the Left Grip A Replacing batteries once a year is recommended SPARE PARTS LIST Replacement Batteries LMS 2x357 Service Kit LMS JMX SK Service Kit includes 1 Grip Screw D 2 Side Plate Screws E 1 Large Hex Wrench G 1 Alignment Tool H 1 Laser Warning Label I 1 Battery Cover J 2 Alignment Screws POWER OUTPUT lt 5 mW DI
Download Pdf Manuals
Related Search