Lanzar Car Audio VBD300 User's Manual
Contents
1. SPEAKER GREEN VIOLET REAR Lch REARRch SPEAKER GREEN BLACK VIOLET BLACK SPEAKER WIRING CONNECTION FOR 4 X 7W OR 2 X 25W SYSTEM CD CHANGER MAIN UNIT d CONNECTOR SOCKET FOR CD CHANGER VERSION ONLV BLACK ANTENNA CONNECTOR CD INPUT CABLE l Leo DE FOR CD INPUT VERSION ONLY GREEN ENTON RED SUBWOOFER CABLE l H N SWITCH B FOR SUBWOOFER VERSION ONLY CHOKE BOX BROWN MEMORY YELLOW FRONT RCA CABLE b Rch RED BACK UP GROUND B BLACK h Lch WHITE GREY POWER BLUE ___REARRCA CABLE ami Rch RED ANTENNA gt S WHITE L SPEAKERS SYSTEM 4 SPEAKERS SYSTEM MD Lch WHITE FOR RCA LINE OUT VERSION ONLY WHITE GREY H H Af WHITE BLACK i GREY BLACK GREEN VIOLET GREEN BLACK VIOLET BLACI ri 4 SPEAKERS SYSTEM 2 SPEAKERS SYSTEM GREV Rehi SPK Note 1 For 2 speakers system green violet white black and grey black wire leads are unconnected and isolated 2 For 2 speakers system keep the fader indicator at center position to maintain the existing volume level LOCATION AND FUNCTION OF CONTROLS i EB Pr ED 1 ON OFF Press POWER button 1 to turn on Press it again to turn it off If2. BAS TRE b BAL FAD VOL Bass Treble Balance Fader Volume CJ Bass Press SEL button 8 for one time Adjust bass level using A 9 and V 10 buttons Treble Press SEL button 8 for two times Adjust treble level using A 9 and V 10 buttons Balance Press SEL button 8 for three times Adjust sound balance between left and right speakers using A 9 and V 10 buttons Fader Press SEL button 8 for four times Adjust sound balance between front and rear speakers using A 9 and V 10 buttons Volume Press SEL button 8 for five times Adjust volume level using A 9 and V 10 buttons 11 BAND Press BND button 11 to change between three FM bands and two AM bands and one LW band Each band stores up to six preset stations B FMI gt FM2 FM3 gt AM1 MW AM2 LW 12 SELECT LISTENING MODE Press MOD button 12 to choose desired listening mode e g radio mode to CD mode to CDC mode e g radio mode to CD mode to to AUX Line 7 13 LIQUID CRVSTAL DISPLAV The LCD 13 can show the current state of the unit 14 8 15 SELECT STATIONS Press and release a TUNE SEEK TRACK button lt lt 14 or gt 15 immediately to move radio frequency number up or down on step Press and hold a TUNE SEEK TRACK button 44 14 or p 15 for several seconds to seek the next clear station 14 amp 15 SKIP TRACKS Press a TUNE SEEK TRACK button lt q
3. Chassis Dimensions Tone Controls Bass at 100 Hz Treble at 10 KHz Maximum Output Power Versionv Version z Version y CD PLAYER Signal to Noise Ratio Channel Separation Frequency Response RADIO Frequency Coverage Sensitivity S N 30 dB Stereo Separation Frequency Coverage Sensitivity S N 20 dB Frequency Coverage IF Sensitivity S N 20 dB 178 W x 155 D x 50 H 10 dB 10 dB 10dB 10dB 7Wx4 ch or 25W x 2 ch 25W x 4 ch 40W x 4 ch More than 60 dB More than 60 dB 20 Hz 20 KHz For 3 Bands For 2 Bands For 2 Bands Europe Europe U S A FM FM FM 87 5 to 108 MHz 87 5 to 108 MHz 87 5 to 107 9 MHz 10 7 MHz 10 7 MHz 10 7 MHz 3 uv 3 uV 3 uv gt 30 dB gt 30 dB gt 30 dB MW MW AM 522 to 1620 KHz 522 to 1620 KHz 530 to 1710 KHz 450 KHz 450 KHz 450 KHz 32 dBu 32 dBu 32 dBu LW 144 to 290 KHz 450 KHz 35 dBu TROUBLE SHOOTING Before going through the check list check wiring connection If any of the problems persist after check list has been made consult vour nearest service dealer Svmptom Cause Solution No power The car ignition is not on If the power supply is properly connected to the car accessory terminal switch the ignition key to ACC The fuse is blown Replace the fuse Disc cannot Presence of CD disc Remove the disc in the player then be loaded or inside the player put a new one ej
4. PLAY ALL TRACKS During CD mode press RND button 20 to play all tracks on CD in random Press again to cancel the function During CDC mode press RND button 20 to play all tracks on the current disc Press it again to play all tracks on all discs in the CD magazine Press it at the third time to cancel the function 21 amp 22 SELECT DISC FOR CD CHANGER VERSION ONLY During CDC mode press D DN button 21 to select previous disc and D UP button 22 to select next disc ATTENTION DURING CDC MODE TURN OFF THE UNIT AND CHANGE THE DISC IN THE CD MAGAZINE THEN TURN IT ON IF THE UNIT CAN T WORK WELL PLEASE PRESS D DN BUTTON 21 OR D UP BUTTON 22 FOR ONE TIME a 23 AUTOMATICALLY STORING amp PROGRAM SCANNING Automatically Storing Press and hold AMS button 23 for several seconds to toggle automatically storing function It starts searching next frequency in local mode and stores the clear station into the preset memory If 6 ch is not fully memorised it would start the second searching in distance mode At the end of automatically storing operation mode is changed to Preset Scan Preset Scanning Press AMS button 23 shortly to toggle preset scanning function During the scanning it will stop at every stored station for several seconds and the number of the channel being scanned flashes on the display Press it again to stop scanning 24 FACEPLATE RELEASE Press RELEASE button 24 to detach the removable facepla
5. 14 or p gt 15 to move to the previous track or the following track Track number shows on the display 14 amp 15 FAST FORWARD AND FAST REVERSE Press a TUNE SEEK TRACK button 44 14 or gt 15 to fast reverse or fast forward CD play starts from when you release the button 16 PRESET STATIONS Six number buttons 16 store and recall stations for each band Store a station Select a band 11 if needed Select a station Hold a preset button for several seconds Recall a station Select a band 11 if needed Press a preset button to select stored station 17 TOP PLAY THE FIRST TRACK Press TOP button 17 to play the first track of the current disc 18 REPEAT THE SAME TRACK During CD mode press RPT button 18 to continuously repeat the same track Press again to stop repeat During CDC mode press RPT button 18 to continuously repeat the same track press it again to continuously repeat all tracks on the current disc and press it at the third time to stop repeat 19 INTRO PREVIEW ALL TRACKS During CD mode press SCN button 19 to play first several seconds of each track on the current disc Press again to stop intro and listen to track During CDC mode press SCN button 19 to play first several seconds of each track on the current disc Press it again to play first several seconds of each track on all discs in the CD magazine Press it at the third time to stop intro and listen to track 20 RANDOM
6. L anzar OWNER S MANUAL VBD 300 PLL SYNTHESIZER STEREO RADIO WITH COMPACT DISC PLAYER DIGITAL INSTALLATION Notes e Choose the mounting location where the unit will not interfere with the normal driving function of the driver e Before finallv installing the unit connect the wiring temporarilv and make sure it is all connected up properly and the unit and the system work properly e Use only the parts included with the unit to ensure proper installation The use of unauthorized parts can cause malfunctions e Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the vehicle e Install the unit where it does not get in the driver s way and cannot injure the passenger if there is a sudden stop like an emergency stop e If installation angle exceeds 30 from horizontal the unit might not give its optimum performance 30 e Avoid installing the unit where it would be subject to high temperature such as from direct sunlight or from hot air from the heater or where it would be subject to dust dirt or excessive vibration DIN FRONT REAR MOUNT This unit can be properly installed either from Front conventional DIN Front mount or Rear DIN Rear mount installation utilizing threaded screw holes at the sides of the unit chassis For details refer to the following illustrated installation methods DIN FRONT MOUNT Me
7. ected ar 3 i Inserting the disc in Insert the compact disc with the reverse direction label facing upward Compact disc is extremely Clean the disc or try to play a new dirty or defective disc one Temperature inside the Cool off or until the ambient car is too high temperature return to normal Condensation Leave the player to off for an hour or so then try again No sound Volume is in minimum Adjust volume to a desired level Wiring is not properly connected Check wiring connection The operation keys do not work Sound skips The built in microcomputer is not operating properly due to noise The installation angle is not more than 30 degrees Press the RESET button Front panel is not properly fixed into its place Adjust the installation angle to less than 30 degrees The disc is extremely dirty or defective disc Clean the compact disc Then try to play a new one The radio does not work The radio station automatic selection does not work The antenna cable is not connected Insert the antenna cable firmiv The signals are too weak Select a station manually www lanzar com 88 C0851 27
8. sole 5 Note The mounting box outer trim ring and half sleeve are not used for method B installation Hook Remove this part HOW TO REMOVE AND INSTALL THE FRONT PANEL OPTIONAL Press the release button and pull off the front panel Keep front panel into the case pare N To install the front panel insert the panel into the housing and make sure the panel is properly installed otherwise abnormalities occurs on the display or some keys will not function properly REMOVING THE FRONT PANEL Front Panel Release Button INSTALLING THE FRONT PANEL WIRING CONNECTION FOR 4 X 25W OR 4 X 40W SYSTEM CD CHANGER MAIN UNIT da CONNECTOR SOCKET FOR CD CHANGER VERSION ONLY BLACK ANTENNA CONNECTOR CD INPUT GABLE b 0 FOR CD INPUT VERSION ONLY SUBWOOFER CABLE GREEN IGNITION RED r SWITCH B FOR SUBWOOFER VERSION ONLY MEMORY YELLOW CHOKE BROWN BACK UP Rch RED BACK BOX FRONT RCA CABLE c GROUND B LD p Lch WHITE GREY POWER BLUE ath Rch RED ANTENNA L PEAR RCA CABLE MI Lch WHITE FOR RCA LINE OUT VERSION ONLY WHITE GREY FRONTLch FRONT Rch SPEAKER WHITE BLACK GREY BLACK
9. te 25 EQUALIZATION Press EQ button 25 to turn on equalization function and to select desired audio mode There are four kinds of mode as below FLAT ROCK CLASSIC POP 26 REMOTE SENSOR OPTIONAL Point the remote handset to control the remote sensor 26 Press the function keys on the remote handset to control the system 27 RESET BUTTON FUNCTION RESET button 27 is placed on the housing and must be activated with either a ball point pen or thin metal object The reset button is to be activated for the following reasons e Initial installation of the unit when all wiring is completed e All the function buttons do not operate e Error symbol on the display Note If press RESET button 27 the unit can t work yet please use a cotton swab soaked in isopropyl alcohol to clean the socket on the back of the front panel Remote Control Handset Control amp Function Keys OONDJRFON POWER Power ON OFF Button MOD Mode Button SEL Select Button EQ Equalization Button BND Band Select Button MUTE Mute Button VOL Volume Up Button VOL Volume Down Button TUN SEK gt Tune Seek Up Button TUN SEK Ha Tune Seek Down Button PRESET Preset Button TOP Top Button SCN Scanning Button RPT Repeat Button RND Random Button SPECIFICATION GENERAL Power Supply Requirements DC 12 Volts Negative Ground
10. the power is off press BND button 11 or MOD button 12 also can turn on the unit 2 DISC PLAY Gently insert a compact disc with the label side facing up into the disc slot 2 The disc is then automatically loaded into the unit and starts playing with the first track of the disc The digital display will indicate the track number 3 MUTE Press the MUT button 3 to silence the receiver Press again to resume listening 4 MONO STEREO FOR MON VERSION ONLY Press MON button 4 to select monaural or stereo Mono reception for radio stations You can sometimes improve reception of distant stations by selecting mono operation 4 SUB WOOFER FOR SUB W VERSION ONLY Press X BAS button 4 to toggle sub woofer output when sub woofer on display will show CSW 5 LOUDNESS Press LOU button 5 to increase bass output and display will show LOUD 6 SET THE CLOCK Press and hold the DSP button 6 then press the pp 15 to change minutes or lt lt 14 to change hours 7 EJECT Push a CD into slot The CD will begin to play Press A eject button 7 to stop CD play and eject CD from slot Receiver switches to radio operation 8 9 amp 10 SELECT MODE Press SEL button 8 to move display through bass treble balance fader and volume functions Use A 9 and y 10 buttons to adjust the selected mode When mode has not been adjusted for several seconds display returns to normal radio or CD display
11. thod A Installation the unit 1 Dashboard 2 Holder After inserting the holder into the dashboard select the appropriate tab according to the thickness of the dashboard material and bend them inwards to secure the holder in place Fig 1 3 Screw DIN REAR MOUNT Method B Oa wn Dashboard Nut 6mm Spring washer Screw 5 x 25mm Screw Strap Be sure to use the strap to secure the back of the unit in place The strap can be bent by hand to the desired angle Plain washer Frame Insert fingers into the groove in the front of frame and pull out to remove the frame When reattaching the frame point the side with a groove downwards and attach it Lever Insert the levers supplied with the unit into the grooves at both sides of the unit as shown in figure until they click Pulling the levers makes it possible to remove the unit from the dashboard Installation using the screw holes on the sides of the unit BON 3 Fastening the unit to the factorv radio mounting bracket 1 Select a position where the screw holes of the bracket and the screw holes of the main unit become aligned are fitted and tighten the screws at 2 places on each side Use either truss screws 5 x 6mm or flush surface screws 4 x 6mm depending on the shape of the screw holes in the bracket Screw Factorv radio mounting bracket Dashboard or Con
Download Pdf Manuals
Related Search