La Crosse Technology WS-9014U User's Manual
Contents
1. Degree Fahrenheit will now show a To change between Fahrenheit and Celsius press and release the MIN MAX button When you have your choice shown on the display press and release the SET button once 3 An hour will now be flashing a Press and release the MIN MAX button until the correct hour is shown Note When in the 12h mode there is PM displayed under the word TIME when in the PM hours During the AM hours this area will be blank b When the correct hour is shown press and release the SET button once 4 A minute will now be flashing a Press and release the MIN MAX button until the correct minutes are displayed Press and release the SET button once more and you are done DETAILED SETUP GUIDE I BATTERY INSTALLATION A REMOTE TEMPERATURE SENSOR 1 Remove the mounting bracket 2 Remove battery cover 3 Observing the correct polarity install 2 AA batteries make sure they do not spring free or start up problems may occur Replace cover B INDOOR TEMPERATURE STATION Note After the batteries are installed DO NOT press any buttons This may interfere with the signals causing temperatures to register incorrectly 1 Remove the battery cover on the backside To do this push up and pull out 2 Observing the correct polarity N install 2 AA TE batteries a i 3 Replace battery e o cover lelle 4 Wait 10 minutes or until bo2. MINUTES In this time the indoor temperature station and remote temperature sensor will start to talk to each other and the display will show both the indoor temperature and an outdoor temperature If the indoor temperature station does not display both temperatures after the 10 minutes please retry the set up as stated above After both indoor and outdoor temperatures are displayed for 10 minutes you can place your remote temperature sensor outdoors and set your time The remote temperature sensor should be placed in a dry shaded area The remote temperature sensor has a range of 80 feet Any walls that the signal will have to pass through will reduce distance An outdoor wall or window will have 20 to 30 feet of resistance and an interior wall will have 10 to 20 feet of resistance Your distance plus resistance should not exceed 80 ft in a straight line NOTE Fog and mist will not harm your remote temperature sensor but direct rain must be avoided To complete the set up of your indoor temperature station after the 10 minutes have passed please follow the steps below 1 Press and hold the SET button for 5 seconds Note A 12h or 24h will appear on the top line 12h for AM PM 24h for military time a To change between 12h and 24h press and release the MIN MAX button When you have your choice shown on the display press and release the SET button once 2
3. WS 9014U Wireless 433 MHz Temperature Station Instruction Manual 765 LA CROSSE w ols and te chnology TECHNO LO G Y f home and office TABLE OF CONTENTS Topic Inventory of Contents Quick Setup Detailed Setup Guide Battery Installation Setting the Time Selecting Units of Measurement Features Minimum and Maximum Temperatures Resetting Minimum and Maximum Temperatures Additional remote temperature sensors optional Mounting Troubleshooting Maintenance and Care Specifications Warranty Information INVENTORY OF CONTENTS 1 The indoor temperature station Figure 1 2 The remote temperature sensor TX6U and mounting bracket Figure 2 3 3 each 1 2 Philips screws 4 One strip of double sided adhesive tape 5 Instruction Manual and Warranty Card Figure 1 EH EEE Figure 2 Tis a tG SEE SN ADDITIONAL EOUIPMENT not included 1 1 Philips screwdriver 2 2 Fresh AA 1 5V batteries 3 2 Fresh AA 1 5V batteries QUICK SETUP Hint Use good quality Alkaline Batteries and avoid rechargeable batteries 1 Have the indoor temperature station and remote temperature sensor 3 to 5 feet apart 2 Batteries should be out of both units for 10 minutes 3 Place the batteries into the remote temperature sensor first then into the indoor temperature station All remote temperature sensors must be started before the indoor temperature station 4 DO NOT PRESS ANY BUTTONS FOR 10
4. echnology The weather station will be repaired or replaced with the same or similar model 22 This warranty does not cover any defects resulting from improper use unauthorized repairs faulty batteries or the weather stations inability to receive a signal due to any source of interference LA CROSSE TECHNOLOGY WILL NOT ASSUME LIABILITY FOR INCIDENTAL CONSEQUENTIAL PUNITIVE OR OTHER SIMILAR DAMAGES ASSOCIATED WITH THE OPERATION OR MALFUNCTION OF THIS WEATHER STATION THIS PRODUCT IS NOT TO BE USED FOR MEDICAL PURPOSES OR FOR PUBLIC INFORMATION THIS PRODUCT IS NOT A TOY KEEP OUT OF CHILDREN S REACH This warranty gives you specific legal rights You may also have other rights specific to your State Some States do no allow the exclusion of consequential or incidental damages therefore the above exclusion of limitation may not apply to you For warranty work technical support or information contact La Crosse Technology 2809 Losey Blvd S La Crosse WI 54601 23 Phone 608 782 1610 Fax 608 796 1020 e mail support lacrossetechnology com warranty work sales lacrossetechnology com information on other products web www lacrossetechnology com FCC DISCLAIMER This device complies with part 15 of the FCC rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that
5. ill arise if this is not done correctly and if 14 the total time for set up exceeds 6 minutes 2 It is necessary to remove the batteries from all units currently in operation 3 Remove the battery covers to all remote temperature sensor units 4 Place all remote temperature sensor units in a numeric sequential order 5 In sequential order install batteries follow the same battery installation procedures seen in section I of the Detailed Set Up Guide 6 Install batteries into the indoor temperature station 7 Follow the Detailed Set Up Guide for programming and operating instructions D VIEWING AND OPERATING WITH MULTIPLE REMOTE TEMPERATURE SENSOR UNITS 1 To view the temperature of a different remote temperature sensor unit press and release the CH button A shift 15 from one boxed number to the next should be observed in the OUTDOOR LCD 2 To view the Minimum Maximum temperature first select from which remote temperature sensor to read data indicated by the boxed number Pressing and releasing the MIN MAX button will toggle through the minimum and maximum indoor temperature and the minimum and maximum outdoor temperature 3 To reset the Minimum Maximum readings press and hold the MIN MAX button for four seconds V MOUNTING Note To achieve a true temperature reading avoid mounting in direct sunlight We recommend that you mount the remote temperature se
6. may cause undesired operation Freq 433 92 MHz La Crosse Technology Made in China WS 9014U 24 FCC ID OMO 01RX Receiver OMO 01TX transmitter THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS 1 THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND 2 THIS DEVICE MUST ACCEPT INTERFERENCE RECEIVED INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION 25
7. mp cloth Do not use solvents or scouring agents they may mark the displays and casings e Do not submerge in water e Do not subject the units to unnecessary heat or cold by placing them in the oven or freezer e Opening the casings invalidates the warranty Do not try to repair the unit Contact La Crosse Technology for repairs 20 SPECIFICATIONS Transmitting 433MHz Frequency Measuring Temperatures Indoor 32 F to 156 2 F with Temperature 0 2 F resolution Station Indoor 0 C to 69 0 C with 0 1 C resolution 21 8 F to 156 2 F with 0 2 F resolution 29 9 C to 69 0 C with 0 1 C resolution 1 F 4 5 C Transmitting Maximum 80 feet 25m range open space Temperature check Indoor Every 10 seconds Outdoor Three times in 10 minutes Batteries Alkaline recommended Remote 2x AA 1 5V Temperature Sensor Indoor Temperature Station Outdoor Temp accuracy 21 Indoor 2 x AAA 1 5V Temperature Station Dimensions L x W x H Indoor Temperature 2 36 x 0 88 x 5 90 in Station Remote Temperature 1 57 x 0 85 x 5 00 in Sensor Battery life Approximately 1 year WARRANTY INFORMATION La Crosse Technology provides a 1 year warranty on this weather station Contact La Crosse Technology immediately upon discovery of any defects covered by this warranty Before sending the weather station in for repairs contact La Crosse T
8. n twice to activate settings 12 IV FEATURES A MINIMUM AND MAXIMUM TEMPERATURES 1 Press and release the MIN MAX button MIN appears in the temperature LCD s and the recorded minimum temperatures are displayed 2 Press and release the MIN MAX button to toggle to the maximum temperatures The time of occurrence of the value for outdoor temperature will also flash B RESETTING THE MINIMUM AND MAXIMUM TEMPERATURES 1 To reset both the minimum and maximum temperatures press and hold the RESET button for 4 seconds C ADDING ADDITIONAL REMOTE TEMPERATURE SENSORS OPTIONAL 13 1 The WS 9014U is able to receive signals from 3 different remote temperature sensors Following are some brief instructions for the basic set up of remote temperature sensor units with the WS 9014U These extra sensors can be purchased through the same dealer as this unit or by contacting La Crosse Technology directly A TX6 will monitor temperature only a TX3U will monitor temperature and display the temperature on its LCD and the TX3UP will monitor the temperature via a probe for use in pools spas etc Note When setting up multiple units it is important to remove the batteries from all existing units in operation then to insert batteries first into all the remote temperature sensor units and in numeric sequence Second install batteries into the indoor temperature station Transmission problems w
9. nsor on an outside North facing wall The sending range is 80ft obstacles such as walls concrete and large metal objects will reduce the range Place 16 both units in their desired location before permanently mounting A REMOTE TEMPERATURE SENSOR 1 Remove the mounting bracket from the remote temperature sensor 2 Mount using either screws or adhesive tape 3 Reattach the remote temperature sensor to the mounting bracket B THE TEMPERATURE STATION 1 The indoor temperature station comes with the table stand already mounted If you wish to use the table stand all that is required is to place the indoor temperature station in an appropriate location 2 To wall mount remove the table stand To do this pull down on the stand from the rear and rotate forward a Fix a screw not included into the desired wall and place the indoor 17 temperature station onto the screw using the hanging hole on the backside Gently pull the indoor temperature station down to lock the screw into place TROUBLESHOOTING NOTE For problems not solved please contact La Crosse Technology via e mail or phone or visit our website www lacrossetechnology com Problem The LCD is faint Solution Replace batteries Problem No outdoor temperature is displayed Solution 1 Remove all batteries reinsert into remote temperature sensor first and then into the indoor temperature station 2 Place remote temperature sensor clo
10. ser to the indoor temperature station 3 Be sure all batteries are fresh 18 4 Place remote temperature sensor and indoor temperature station in position so the straight line signal is not passing through more than two or three walls Problem Temperatures do not match if units are placed next to each other Solution Each temperature sensor is manufactured to be accurate to within 1 degree plus or minus and under normal conditions so two temperature sensors could be as much as 2 degrees different However the difference can be exaggerated further because the temperature sensors are designed for different working environments The indoor sensor is less responsive to ambient air currents because of the shielding effect of the display s case In addition the case can act as a heat sink to absorb and store heat from external sources i e handling of the case or radiant heat In addition the much greater range of the outdoor temperature sensor requires a different calibration curve than the indoor range Error is usually greater at the extreme 19 ends of a range making it harder to compare different ranges with different curves Under non laboratory conditions it is difficult to compensate for the above factors and obtain an accurate comparison MAINTENANCE AND CARE INSTRUCTIONS e Extreme temperatures vibration and shock should be avoided to prevent damage to the units e Clean displays and units with a soft da
11. th the indoor and outdoor temperatures are shown on the indoor temperature station 5 The indoor temperature station eH te should now show in the TIME LCD and temperatures in the INDOOR and OUTDOOR LCD s 10 TI TIME A SETTING THE TIME 1 Press and hold the SET ee button for 5 set C channel second 12h will appear in A the TIME LCD reset C min max 2 Press and release the MIN MAX button to select either 12h time am pm or 24h time 3 Press and release the SET button 2 times the hour will flash in the upper left corner 4 Press and release the MIN MAX button to set the hours 5 Press and release the SET button to move to the minute setting 6 Press and release the MIN MAX button to set the minutes 7 Press and release the SET button to activate the clock 11 Note When in 12h mode there is only a PM display which appears under TIME If there is no display here it is AM Make sure you set the time accordingly TIL UNITS OF TEMPERATURE MEASURE A SELECTING UNITS OF MEASUREMENT 1 Press and hold the SET button for 5 second until 12h or 24h appears in the TIME LCD 2 Press and release the SET button again F will appear in the TIME LCD 3 Press and release the MIN MAX button to shift between F and C 4 Press and release the SET butto
Download Pdf Manuals
Related Search