La Crosse Technology WS-7034U User's Manual
Contents
1. No outdoor temperature is displayed Solution 1 Remove all batteries reinsert into remote temperature sensor first then into the indoor temperature station 2 Place remote temperature sensor closer to the indoor temperature station 3 Be sure all batteries are fresh 4 Place remote temperature sensor and indoor temperature station in position so the straight line signal is not passing through more than two or three walls Problem Temperatures do not match if units are placed next to each other 17 Solution Each temperature sensor is manufactured to be accurate to within 1 degree plus or minus and under normal conditions so two sensors could be as much as 2 degrees different However the difference can be exaggerated further because the sensors are designed for different working environments The indoor sensor is less responsive to ambient air currents because of the shielding effect of the display s case In addition the case can act as a heat sink to absorb and store heat from external sources i e handling of the case or radiant heat Also the much greater range of the outdoor temperature sensor requires a different calibration curve than the indoor range Error is usually greater at the extreme ends of a range making it harder to compare different ranges with different curves Under non laboratory conditions it is difficult to compensate for the above factors and obtain an accurate comparison MAINTENANC2. Say 2 Press and release the MIN MAX button to select either 12h time am pm or 24h time 3 Press and release the SET button 2 times the hour will flash in the upper left corner 4 Press and release the MIN MAX button to set the hours 5 Press and release the SET button to move to the minute setting 6 Press and release the MIN MAX button to set the minutes 7 Press and release the SET button to activate the clock Note When in 12h mode there is only a PM display which appears under TIME If there is no display here it is AM Make sure you set the time accordingly Selecting Units of Measurement 1 Press and hold the SET button for 5 second until 12h or 24h appears in the TIME LCD 2 Press and release the SET button again F will appear in the TIME LCD 3 Press and release the MIN MAX button to shift between F and C 4 Press and release the SET button twice to activate settings 10 FEATURES Minimum and Maximum Temperatures 1 Press and release the MIN MAX button MIN appears next to the indoor and remote temperatures The recorded minimum temperature is displayed The time of the minimum outdoor temperature will also flash Press the MIN MAX button MAX appears next to the indoor and remote temperatures The recorded maximum temperature is displayed The
3. DAMAGES ASSOCIATED WITH THE OPERATION OR MALFUNCTION OF THIS PRODUCT THIS PRODUCT IS NOT TO BE USED FOR MEDICAL PURPOSES OR FOR PUBLIC INFORMATION THIS PRODUCT IS NOT A TOY KEEP OUT OF CHILDREN S REACH 23 This warranty gives you specific legal rights You may also have other rights specific to your State Some States do no allow the exclusion of consequential or incidental damages therefore the above exclusion of limitation may not apply to you For warranty work technical support or information contact La Crosse Technology 2809 Losey Blvd S La Crosse WI 54601 Phone 608 782 1610 Fax 608 796 1020 e mail support lacrossetechnology com warranty work sales lacrossetechnology com information on other products web www lacrossetechnology com FCC DISCLAIMER This device complies with part 15 of the FCC tules Operation is subject to the following two conditions 1 this device may not cause harmful 24 interference and 2 this device must accept any interference received including interference that may cause undesired operation Freq 433 92 MHz La Crosse Technology Made in China WS 7034U FCC ID OMO 01RX Receiver OMO 01TX sensor THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS 1 THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND 2 THIS DEVICE MUST ACCEPT INTERFERENCE RECEIVED INCLUDING INTERFERENCE THAT MAY CAU
4. E AND CARE INSTRUCTIONS 18 Extreme temperatures vibration and shock should be avoided to prevent damage to the units Clean displays and units with a soft damp cloth Do not use solvents or scouring agents they may mark the displays and casings Do not submerge in water Do not subject the units to unnecessary heat or cold by placing them in the oven or freezer Opening the casings invalidates the warranty Do not try to repair the unit Contact La Crosse Technology repairs 19 SPECIFICATIONS Transmitting 433MHz Measuring Temperatures Indoor 32 F to 156 2 F with 0 2 Temperature F resolution Station 0 C to 69 0 C with 0 1 C resolution Remote 21 8 F to 156 2 F with Temperature 0 2 F resolution Sensor 29 9 C to 69 0 C with 0 1 C resolution Temp accuracy 1 F 5 C Transmitting Maximum 80 feet 25m range open space Temperature check Indoor Every 10 seconds Outdoor Three times in 10 minutes Batteries Alkaline recommended Remote 2 x AA 1 5V Temperature Sensor 20 Indoor 2 x AAA 1 5V Temperature Station Dimensions L x W x H Indoor 2 36 x 88 x 5 90 in Temperature excluding table stand Station 60 x 22 5 x 150 mm Remote 2 32 x 0 86 x 2 55 in Temperature 59 x 22 x 65 mm Sensor Battery life Approximately 1 year WARRANTY INFORMATION La Crosse Technology Ltd provides a 1 year limited warranty on this product against manufac
5. SE UNDESIRED OPERATION 25
6. WS 7034U Wireless 433 MHz Temperature Station Instruction Manual LA CROSSE tools and technology TECHNOLOGY for home and office TABLE OF CONTENTS wjr D vja Inventory of Contents 6 Setting the Time 9 Selecting Units of 10 Measurement i 1 o Minimum and Maximum Resetting Minimum and 1 Adding additional remote 13 14 temperature sensors optional 15 16 17 18 7 1 2 QUICK SETUP Hint Use good quality Alkaline Batteries and avoid rechargeable batteries 1 Have the indoor temperature station and remote temperature sensor 3 to 5 feet apart 2 Batteries should be out of both units for 10 minutes 3 Place the batteries into the remote temperature sensor first then into the indoor temperature station All remote temperature sensors must be started before the indoor temperature station 4 DO NOT PRESS ANY BUTTONS FOR 10 MINUTES In this time the indoor temperature station and remote temperature sensor will start to talk to each other and the display will show both the indoor temperature and an outdoor temperature If the indoor temperature station does not display both temperatures after the 10 minutes please retry the set up as stated above After both indoor and outdoor temperatures are displayed for 10 minutes you can place your remote temperature sensor outdoors and set your time The remote temperature sensor should be placed in a dry shaded area The remote
7. lease the SET CH button A shift from one number to the next should be observed in the OUTDOOR LCD 14 MOUNTING Note To achieve a true temperature reading avoid mounting in direct sunlight We recommend that you mount the remote temperature sensor on a North facing wall The sending range is 80ft obstacles such as walls concrete and large metal objects will reduce the range Place both units in their desired location before permanently mounting Remote Temperature Sensor 1 Remove the mounting bracket from the remote temperature sensor 2 Mount the bracket in the desired location with either screws or adhesive tape 3 Reattach the remote temperature sensor into mounting bracket 15 Indoor Temperature Station The indoor temperature station comes with the table stand already mounted If you wish to use the table stand all that is required is to place the indoor temperature station in an appropriate location 1 To wall mount the indoor temperature station first remove the table stand 2 Next insert an appropriate screw in your desired location 3 Using the integrated hanging hole on the back of the unit slip indoor temperature station over the screw and pull down to secure 16 TROUBLESHOOTING NOTE For problems not solved please contact La Crosse Technology via e mail or phone or visit our website www lacrossetechnology com Problem The LCD is faint Solution Replace batteries Problem
8. sse Technology Ltd product to a La Crosse Technology Ltd authorized service center La Crosse Technology Ltd will pay ground return shipping charges to the owner of the product to a USA address only Your La Crosse Technology Ltd warranty covers all defects in material and workmanship with the following specified exceptions 1 damage caused by accident unreasonable use or neglect including 22 the lack of reasonable and necessary maintenance 2 damage occurring during shipment claims must be presented to the carrier 3 damage to or deterioration of any accessory or decorative surface 4 damage resulting from failure to follow instructions contained in your owner s manual 5 damage resulting from the performance of repairs or alterations by someone other than an authorized La Crosse Technology Ltd authorized service center 6 units used for other than home use 7 applications and uses that this product was not intended or 8 the products inability to receive a signal due to any source of interference This warranty covers only actual defects within the product itself and does not cover the cost of installation or removal from a fixed installation normal set up or adjustments claims based on misrepresentation by the seller or performance variations resulting from installation related circumstances LA CROSSE TECHNOLOGY LTD WILL NOT ASSUME LIABILITY FOR INCIDENTAL CONSEQUENTIAL PUNITIVE OR OTHER SIMILAR
9. temperature sensor has a range of 80 feet Any walls that the signal will have to pass through will reduce distance An outdoor wall or window will have 20 to 30 feet of resistance and an interior wall will have 10 to 20 feet of resistance Your distance plus resistance should not exceed 80 ft in a straight line NOTE Fog and mist will not harm your remote temperature sensor but direct rain must be avoided To complete the set up of your indoor temperature station after the 10 minutes have passed please follow the steps on pages 8 9 INVENTORY OF CONTENTS 1 The indoor temperature station Figure 1 2 The remote temperature sensor TX6U and mounting bracket Figure 2 3 each 1 2 Philips screws One strip of double sided adhesive tape Instruction Manual and Warranty Card PR Figure 1 Holder ea Figure 2 ADDITIONAL EQUIPMENT not included 1 1 Philips screwdriver 2 2 Fresh AAA Alkaline batteries 3 2 Fresh AA Alkaline batteries DETAILED SETUP GUIDE Battery Installation 1 Install 2 AA batteries in the remote temperature sensor Make sure they do not spring free or start up problems may occur 2 Install 2 AAA batteries in the Battery indoor temperature i Cover station Do not _ press any buttons i for at least ten el minutes Setting the Time 1 Press and hold the SET button for 5 if ns Y second 12h will eee appear in the TIME NEA LCD
10. time of the maximum outdoor temperature will also flash Press and release the MIN MAX button to exit min max mode To view optional additional sensors press and release the SET button while viewing the minimum or maximum 11 Resetting Min and Max Temperatures To reset both the minimum and maximum temperatures press and hold the RESET button for 4 seconds 12 Adding Additional Remote Temperature Sensors optional The WS 7034U is able to receive signals from 3 different remote temperature sensors Following are some brief instructions for the basic set up of remote temperature sensor units with the WS 7034U These extra remote temperature sensors can be purchased through the same dealer as this unit or by contacting La Crosse Technology directly A TX6U will monitor temperature only a TX3U will monitor temperature and display the temperature on its LCD and the TX3UP will monitor the temperature of water or soil via a probe When setting up multiple remote temperature sensors it is important to remove the batteries from all existing units in operation then to insert batteries first into all the remote temperature sensors Second install batteries into the 13 indoor temperature station and do not press any buttons for ten minutes Transmission problems will arise if this is not done correctly To view the temperature of a different remote temperature sensor unit press and re
11. turing defects in materials and workmanship This limited warranty begins on the original date of purchase is valid only on products purchased and used in North America and only to the original purchaser of this product To receive warranty service the purchaser must contact La Crosse Technology Ltd for problem determination and service procedures Warranty service can only be performed by a La Crosse Technology Ltd 21 authorized service center The original dated bill of sale must be presented upon request as proof of purchase to La Crosse Technology Ltd or La Crosse Technology Ltd s authorized service center La Crosse Technology Ltd will repair or replace this product at our option and at no charge as stipulated herein with new or reconditioned parts or products if found to be defective during the limited warranty period specified above All replaced parts and products become the property of La Crosse Technology Ltd and must be returned to La Crosse Technology Ltd Replacement parts and products assume the remaining original warranty or ninety 90 days whichever is longer La Crosse Technology Ltd will pay all expenses for labor and materials for all repairs covered by this warranty If necessary repairs are not covered by this warranty or if a product is examined which is not in need or repair you will be charged for the repairs or examination The owner must pay any shipping charges incurred in getting your La Cro
Download Pdf Manuals
Related Search