Kuppersbusch USA GMS 6540.0 E-UL User's Manual
Contents
1. Not obstructing the flow combustion and ventilation air USE 2 BURNERS A diagram is screen printed above each knob on the front panel This diagram indicates to which burner the knob in question corresponds After having opened the gas mains or gas bottle tap light the burners as described below manual ignition Push and turn the knob corresponding to the required burner in an anticlockwise direction until it reaches the full on position large flame fig 1 then place a lighted match near the burner Electrical ignition Push and turn the knob corresponding to the required burner in an anticlockwise direction until it reaches the full on position large flame fig 1 then depress and release the ignition button E Automatic electrical ignition Push and turn the knob corresponding to the required burner in an anticlockwise direction until it reaches the full on position large flame fig 1 then depress the knob Lighting burners equipped with flame failure device The knobs of burners equipped with flame failure device must be turned in an anticlockwise direction until they reach the full on position large flame fig 1 and come to a stop Now depress the knob in question and repeat the previously indicated operations Keep the knob depressed for about 10 seconds once the burner has ignited HOW TO USE THE BURNERS Bear in mind the following indications in order to achieve maximum2. T fig 3 have not become clogged by foreign bodies Check that enamelled burner cap C fig 3 have correctly positioned on the burner head It must be steady The exact position of the pan support is established by the rounded corners which should be set towards the side edge of the hot plate Do not force the taps if they are difficult open or close Contact the technical assistance service for repairs Don t use steam jets for the equipment cleaning INSTALLATION TECHNICAL INFORMATION FOR THE INSTALLER Installation adjustments of controls and maintenance must only be carried out by a qualified engineer Incorrect installation may cause damage to persons animals or property for which the Manufacturer shall not be considered responsible During the life of the system the automatic safety or regulating devices on the appliance may only be modified by the manufacturer or by his duly authorized dealer 4 INSTALLING THE WORKTOP Check that the appliance is in a good condition after having removed the outer packaging and internal wrappings from around the various loose parts In case of doubt do not use the appliance and contact qualified personnel Never leave the packaging materials cardboard bags polystyrene foam nails etc within children s reach since they could become potential sources of danger The measurements of the opening made in the top of the modular cabinet and into which
3. before it is opened If the appliance has a glass lid this could shatter when the hot plate becomes hot Always switch off all the burners before closing the lid Containers wider than the unit are recommended RILI USE Notes use of a gas cooking appliance produces heat and moisture in the room in which it ts installed The room must therefore be well ventilated Intensive and lengthy use of the appliance may require additional ventilation This can be achieved by opening a window or by increasing the power of the mechanical exhausting system if installed WARNING NEVER use this appliance as a space heater to heat or warm the room Doing so may result in carbon monoxide poisoning and overheating ot the oven CLEANING IMPORTANT always disconnect the appliance from the gas and electricity mains before carrying out any cleaning operation 3 WORKTOP Periodically wash the hot plate the enamelled stell pan support the enamelled burner caps C and the burner heads T see fig 3 with lukewarm soapy water Following this all parts should be thoroughly rinsed and dried Never wash them while they are still warm and never use abrasive powders Do not allow vinegar coffee milk salted water lemon or tomato juice from remaining in contact with the enamelled surfaces for long periods of time WARNINGS comply with the following instructions before remounting the parts check that burner head slots
4. 403 7ULKUP 25 06 2009 DESCRIPTION OF HOBS TYPES GMS 6540 0 E UL TYPES GMS 9551 0 E UL SS LHE DH ES E K FAHA EN SZ N Ka Ka AN KA lt FBF RARA C OF 13 12 11 9 10 1 Ultra rapid gas burner 11000 Btu h 2 Rapid gas burner 10000 Btu h 3 Semirapid gas burner 6100 Btu h 4 Semirapid gas burner 6100 Btu h 5 Auxiliary gas burner 3550 Btu h 6 Enamelled steel pan support 2F 7 Enamelled steel pan support central 8 Burner n 1 control knob 9 Burner n 2 control knob 10 Burner n 3 control knob 11 Burner n 4 control knob 12 Burner n 5 control knob 13 Electric ignition button Attention this appliance has been manufactured for domestic use only and it employment by private person SAFE GUARD INSTRUCTIONS 1 SAFE GUARD INSTRUCTIONS For all appliances the product shall be installed according with the a statement that the installation must conform with local codes or in absence of local codes with the National Fuel Gas Code ANSI Z223 1 NFPA 54 The product must be electrically grounded in accordance with local codes or in the absence of local codes with the National Electrical Code ANSI NFPA 70 The appliance and its individual shutoff valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressure in excess of psi 3 5 kPa The maximun gas supply pressure is 4 inch WC and 11 inch WC and the gas pressure regulator provided is regul
5. Hz Frequency 60 Hz 14 TECHNICAL DATA FOR THE APPLIANCE GAS REGULATION TECHNICAL ASSISTANCE AND SPARE PARTS Before leaving the factory this appliance will have been tested and regulated by expert and specialized personnel in order to guarantee the best performances Any repairs or adjustments which may be subsequently required may only be carried out by qualified personnel with the utmost care and attention For this reason always contact your Dealer or our nearest After Sales Service Center whenever repairs or adjustments are required specifying the type of fault and the model of the appliance in your possession Please also note that genuine spare parts are only available from our After Sales Service Centers and authorized retail outlets The above data are printed on the data label put on the inferior part of the appliance and on the packing label The above informations give to the technical assistant the possibility to get fit spare parts and a heaven sent intervention We suggest to fill the table below MARK eek MODEL une SERIES inne eben 15 Kuppersbusch USA 1883 Massaro Blvd Tampa FL 33619 Toll 800 459 0844 P 813 288 8890 F 813 288 8604 Kuppersbusch THE FUTURE OF COOKING SINCE 1875
6. INSTRUCTIONS AND ADVICE FOR THE USE INSTALLATION AND MAINTENANCE OF MIXED AND GAS FUELLED BUILT IN HOT PLATES Dear Customer Thank you for having purchased one of our products We are certain that this new modern functional and practical appliance built with the very highest quality materials will meet your requirements in the best possible way This appliance is easy to use It is however important to thoroughly read the instructions in this handbook in order to obtain the best results These instructions are only valid for the countries of destination the identification symbols of which are indicated on the cover of the instruction manual and on the appliance itself The manufacturer shall not be held responsible for any damages to persons or property caused by incorrect installation or use of the appliance Kuppersbusch USA 1883 Massaro Blvd Tampa FL 33619 Toll 800 459 0844 P 813 288 8890 F 813 288 8604 K ppersbusch THE FUTURE OF COOKING SINCE 1875 MODELS GMS 6540 0 E UL GMS 9551 0 E UL The Manufacturer shall not be held responsible for any inaccuracies in this handbook due to printing or transcription errors the designs in the figures are purely indicative The Manufacturer also reserves the right to make any modifications to the products as may be considered necessary or useful also in the interests of the user without jeopardizing the main functional and safety features of the products themselves COD 0
7. ated to 1 inch water column above the manufacturer s specified manihold pressure Always disconnect all cord connect appliances shall include instructions relative to location ot the wall receptacle and the warning to the user to disconnect the electrical supply before servicing the appliance WARNING If the information on this manual is not followed exactly a fire or explosion may result causing property damage personal injury or death Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance WHAT TO DO IF YOU SMELL GAS Do not try to light any appliance Do not touch any electrical switch do not use any phone in your building Immediately call your gas supplier from a neighbor s phone Follow the gas supplier s instructions If you cannot reach your gas supplier call the fire department Installation and service must be performed by a qualified installer service agency or the gas supplier Save the orifices removed from the appliance for future use When a flexible service cord of the grounding type is provided to connect the appliance to a line voltage electrical supply the instructions shall also include the intent of the warning statement specified in 1 29 12 The maximum depth cabinets installed above cooking tops be 13 in 330 mm Keeping appliance area clear and free from combustible materials gasoline and other flammable vapors and liquids
8. by screws at a minimum distance of 150 mm from the lower surface of the top see fig 4 COMPLY WITH THE DIMENSIONS in mm A B C DIE INSTALLATION 6 ROOM VENTILATION To ensure correct operation of the appliance it is important to ensure that the room where the hot plate is installed has sufficient ventilation 7 GAS CONNECTION Natural Gas and Propane Gas Natural Gas installations require the connection of a gas regulator at the appliance This regulator is supplied with the appliance on purchase Assemble the regulator noting the gas flow direction and transition pieces Supplied with the appliance in accordance with below figure GAS INLET PIPE ELBOW CONNECTION GASKET The transition piece on the supply side of the regulator must be provided by the installer Unions compatible with the hose fittings must be used and connections tested for gas leaks Ensure the supply connection point is accessible with the appliance installed Warning ensure that the hose assembly is restrained from accidental contact with the flue or flue outlet of an underbench oven INSTALLATION 8 ELECTRICAL CONNECTION The electrical connections of the appliance must be carried out in compliance with the provisions and standards in force Before connecting the appliance check that the electrical capacity of the mains supply and current sockets suit the maximum power rating of the appliance consult the da
9. efficiency with the least possible gas consumption use adequate pans for each burner consult the following table and fig 2 When the pan comes to the boil set the knob to the reduced rate position small flame fig 1 Always place a lid on the pans Use only pan with a flat bottom Full on position Reduced rate position Ultra rapid 11000 Btu h 24 26 Rapid TooooBum 2022 Rapid S100 Buh 16648 S100 Buh 16x18 9550 Buh 10414 WARNINGS burners with flame failure device may only be ignited when the relative knob has been set to the Full on position large flame fig 1 Matches can be used to ignite the burners in a blackout Never leave the appliance unattended when the burners are being used Make sure there are no children in the near vicinity Particularly make sure that the pan handles are correctly positioned and keep a chek on foods requiring oil and grease to cook since these products can easily catch fire The machine must not be used by people including children with impaired mental or physical capacities or without experience of using electrical devices unless supervised or instructed by an expert adult responsible for their care and safety Children should not be allowed to play with the equipment Never use aerosols near the appliance when it is operating If the built in hot plate has a lid any spilt food should be immediately removed from this
10. nts liquid from infiltrating into the cabinet Strictly comply with the following instructions in order to correctly apply this seal detach the seals from their backing checking that the transparent protection still adheres to the seal itself Overturn the hot plate and correctly position seal E fig 6 under the edge of the hot plate itself so that the outer side of the seal perfectly matches the outer perimetral edge of the hot plate The ends of the strips must fit together without overlapping Evenly and securely fix the seal to the hot plate pressing into place with the fingers and remove the strip of protective paper from the seal and set the plate into the hole made in the cabinet 10 Fix the hob with the proper brackets S and fit the prominent part into the porthole H on the bottom turn the screw F until the bracket S stick on the top fig 7 The prospective walls left or right that exceed the working table in height must be at a minimum distance from the cutting as mentionned both in the columns and the scheme In order to avoid accidental touch with the overheating bottom of the hob during the working is necessary to put a wooden insert fixed by screws at a minimum distance of 60 mm from the lower surface of the top see fig 4 ADJUSTMENTS Always disconnect the appliance from the electricity main before making any adjustments All seals must be replaced by the
11. sted operations the burners fig 12 taps fig 13 and electrical components can all be replaced fig 14 NB the ignition bar must be removed before replacing the taps in appliances with automatic ignition systems It is advisable to change seal D whenever a tap is replaced to ensure a perfect tightness Greasing the taps see fig 15 16 If a tap becomes stiff to operate it must be immediately greased in compliance with the following instructions remove the tap Clean the cone and its housing using a cloth soaked in diluent Lightly spread the cone with the relative grease Fit the cone back in place operate it several times and then remove it again Eliminate any excess grease and check that the gas ducts have not become clogged Fit all parts back in place complying with the demounting order in reverse The tight closure test must be done using a foamy liquid The use of the flame is prohibited To facilitate the servicing technician s task here is a chart with the types and sections of the powering cables and the ratings of the electrical components TECHNICAL DATA ON THE DATA LABEL 4 BURNERS 60 5 BURNERS 90 PROPANE HD 5 11 inches water column PROPANE HD 5 11 inches water column NATURAL GAS 7 inches water column NATURAL GAS 7 inches water column gt Qn Natural Gas 25750 Btu h gt Qn Natural Gas 36750 Btu h Voltage 120 V AC Voltage 120 V AC Frequency 60
12. ta label applied to the underside of the hot plate The socket or system has an efficient earth connection in compliance with the provisions and standards in force The manufacturer declines all responsibility for failing to comply with these provisions When the appliance is connected to the electricity main by a socket fit a standard plug suited to the load indicated on the data label to the cable Fit the wires following figure 8 taking care of respecting the following correspondences Letter L live wire Letter N neutral wire earth symbol green or yellow green wire Never use reductions adapters of shunts for connection since these could create false contacts and lead to dangerous overheating The outlet must be accessible after the built in When the appliance is connected straight to the electricity main install an omnipolar circuit breaker between the appliance and the electricity main This circuit breaker should be sized in compliance with current installation regulations Remember that the earth wire must not be interrupted by the circuit breaker For optimum safety the electrical connection may also be protected by a high sensitivity differential circuit breaker You are strongly advised to fix the relative yellow green earth wire to an efficient earthing system INSTALLATION 9 FIXING THE WORKTOP The hot plate has a special seal which preve
13. technician at the end of any adjustments or regulations Our burners do not require primary air adjustment 10 TAPS Reduced rate adjustment Switch on the burner and turn the relative knob to the Reduced rate position small flame fig 1 Remove knob M fig 9 of the tap which is simply pressed on to its rod Insert a small screwdriver D into hole C fig 9 and turn the throttle screw to the right or left until the burner flame has been adequately regulated to the Reduced rate position Check that the flame does not go out when the knob is sharply switched from the Full on to the Reduced rate position It is understood that only burners operating with Natural Gas or Town gas should be subjected to the above mentioned adjustments The screw must be fully locked when the burners operate with Propane HD 5 turn clockwise 11 CONVERSIONS 11 REPLACING THE INJECTORS The burners can be adapted to different types of gas by mounting injectors suited to the type of gas in question To do this first remove the burner tops using a wrench B Now unscrew injector A see fig 10 and fit a injector corresponding to the utilized type of gas in its place It is advisable to strongly tighten the injector in place After the injectors have been replaced the burners must be regulated as explained in paragraphs 10 The technician must reset any seals on the reg
14. the hot plate will be installed are indicated in either fig 4 Always comply with the measurements given for the hole into which the appliance will be recessed see fig 4 and 5 5 FIXING THE HOT PLATE The hot plate has a special seal which prevents liquid from getting into the cabinet Strictly comply with the following instructions in order to correctly apply this seal detach the seals from their backing checking that the transparent protection still adheres to the seal itself Overturn the hot plate and correctly position seal E fig 6 under the edge of the hot plate itself so that the outer side of the seal perfectly matches the outer edge of the hot plate The ends of the strips must fit together without overlapping Evenly and securely fix the seal to the hot plate pressing into place with the fingers and remove the strip of protective paper from the seal and set the plate into the hole made in the cabinet Fix the hob with the proper brackets S and fit the prominent part into the porthole H on the bottom turn the screw F until the bracket S stick on the top fig 7 The prospective walls left or right that exceed the working table in height must be at a minimum distance from the cutting as mentionned both in the columns and the scheme In order to avoid accidental touch with the overheating bottom of the hob during the working is necessary to put a wooden insert fixed
15. ulating or pre regulating devices The envelope with the injectors and the labels can be included in the kit or at disposal to the authorized customer Service Centre For the sake of convenience the nominal rate table also lists the heat inputs of the burners the diameter of the injectors and the working pressures of the various types of gas BURNER ARRANGEMENT ON THE HOT PLATE gt 000000 TABLE NORMAL INJECTOR NOMINAL HEAT BURNERS PRESSURE DIAMETER INPUT Btu h GAS inches water N DESCRIPTION column 1 100 mm Min Max PROPANE HD 5 11 94 4400 11000 1 ULTRA RAPID NATURAL GAS 7 176 4400 11000 gt RAPID PROPANE HD 5 11 91 2500 10000 NATURAL GAS 7 155 2500 10000 PROPANE HD 5 11 70 1500 6100 3 SEMIRAPID NATURAL GAS 7 120 1500 6100 PROPANE HD 5 11 70 1500 6100 4 SEMIRAPID NATURAL GAS 7 120 1500 6100 PROPANE HD 5 11 53 1200 3550 gt AUXILIARY NATURAL GAS 7 90 1200 3550 12 SERVICING Always disconnect the appliance from the electricity and gas mains before proceeding with any servicing operation 12 REPLACING COMPONENTS Replacement of the components housed inside the appliance remove the trivets and the burners from the upper part of the working table remove the fixing screws V of the burner fig 11 and the knobs fixed by pressure with the hans in order to take off the appliance After having carried out the above li
Download Pdf Manuals
Related Search