Kramer Electronics VP-419xl User's Manual
Contents
1. Getting Started Step 1 Mount the machine Mount the machine tn a rack or stick the 4 rubber feet to the underside o Video Ts EXGA7 HO Sealer CONNECT THE INPUTS AND THE OUTPUT Composite Video Player Plasma Display s Video Camcorder You do not have to connect all 7 the inputs Computer Graphics Source Step 3 Turn the power ON Step 4 Control the machine see section 6 VIA THE FRONT PANEL BUTTONS CONTROL MENU ENTER INPUT SELECTOR cv YC Comp SXGA O TRANSMITTER Select the output CONTROL via Select the resolution or reset the OSD INPUT to VGA 480p menus VIA THE IR REMOTE CONTROL 9 KRAMER SIMPLE CREATIVE TECHNOLOGY Overview 3 Overview The Kramer VP 419x1 Video To SXGA HD Scaler is a high quality converter for up scaling composite video s Video YC and SD component video to XGA and HD resolutions It also has a computer graphics XGA input which when selected or when the machine is not powered is routed directly bypassed to the output Video inputs are de interlaced and scaled to the selected PC or HDTV resolutions as follows e VGA 640x480 e SXGA 1280x1024 e 720p e SVGA 800x600 e 480p e 1080i e XGA 1024x768 e 576p The VP 419xl Video To SXGA HD Scaler also features e Automatic detection of NTSC PAL B PAL G PAL I PAL D and SECAM video standar2. including warranties of merchantability and fitness for a particular purpose are limited in duration to the length of this warranty EXCLUSION OF DAMAGES The liability of Kramer for any effective products is limited to the repair or replacement of the product at our option Kramer shall not be liable for 1 Damage to other property caused by defects in this product damages based upon inconvenience loss of use of the product loss of time commercial loss or 2 Any other damages whether incidental consequential or otherwise Some countries may not allow limitations on how long an implied warranty lasts and or do not allow the exclusion or limitation of incidental or consequential damages so the above limitations and exclusions may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from place to place NOTE All products returned to Kramer for service must have prior approval This may be obtained from your dealer This equipment has been tested to determine compliance with the requirements of EN 50081 Electromagnetic compatibility EMC generic emission standard Part 1 Residential commercial and lightindustry EN 50082 Electromagnetic compatibility EMC generic immunity standard Part 1 Residential commercial and light industry environment CFR 47 FCC Rules and Regulations Part 15 Radio frequency devices Subpart B Unintentional radiators CAUTI
3. 6 Controlling the VP 419xl The VP 419xl can be controlled directly via the front panel buttons see section 6 1 via the OSD menu see section 6 2 and or remotely from the infra red remote control transmitter see section 6 3 6 1 Controlling via the Front Panel Buttons The VP 419x includes the following control front panel buttons e An RGB RESET button for setting the output to either RGB or Y Pb Pr or resetting the resolution to VGA or 480p e CONTROL buttons including the MENU ENTER and buttons e INPUT SELECTOR buttons for selecting the required input CV YC COMP or SXGA 6 2 Using the CONTROL Buttons The CONTROL buttons let you control the VP 419x1 via the OSD menu e Press the MENU button to enter the menu e Press the ENTER button to accept changes and to change the menu settings e Press the and buttons to move through the OSD menu which is displayed on the video output or adjust the PICTURE parameters On the OSD menu select EXIT to exit the menu 6 2 1 The MAIN MENU Table 4 defines the MAIN MENU features and functions Table 4 The MAIN MENU Features Mode Function PICTURE Set the picture parameters contrast brightness color hue detail and reset see section 6 2 2 SOURCE Select the desired input source video s Video Y CB CR or computer RESOLUTION After selecting the output type select between the RGB output resolutions VGA SVGA XGA or SXGA or the YPbPr out
4. Set the output resolution to 852x480p 576p Set the output resolution to 852x576p 720p Set the output resolution to 1280x720p 1080i Set the output resolution to 1920x1080i ASPECT Select the standard normal 4 3 or the wide 16 9 aspect ratio PICTURE Press and hold for 2 seconds to reset RESET all the ProcAmp settings contrast brightness and so on 3D Turn the 3D enhance feature ON or OFF NR Turn the digital noise reduction feature ON or OFF MENU Enter the OSD menu ENTER Press to accept changes and to change SETUP parameters Figure 3 Infra Red Remote Control Transmitter vy 4 Press to adjust the picture parameters 1 In some versions you need to be within the PICTURE menu to do this 10 KRAMER SIMPLE CREATIVE TECHNOLOGY Technical Specifications 7 Technical Specifications Table 8 Technical Specifications of the VP 419xl Video To SXGA HD Scaler INPUTS 1 VGA SVGA XGA SXGA on an HD15F connector 1 composite video on an RCA connector 1 component video Y Cb Cr on RCA connectors 1 s Video on a 4p connector OUTPUT 1 RGB YPbPr on an HD15F connector OUTPUT RESOLUTIONS VGA 640x480 SVGA 800x600 XGA 1024x768 SXGA 1280x1024 HDTV 480p 576p 720p 1080i PROCESSING DELAY 2 frames CONTROLS Front panel buttons and infra red remote for menu driven OSD control ADDITIONAL CONTROLS Contrast brightness color tint and sha
5. 2 1 6 Connect an s Video source for example an s Video camcorder to the YC INPUT 4p connector Connect a composite video source for example a composite video player to the CV INPUT RCA connector Connect a component video source for example a DVD player to the Y Cb and Cr INPUT RCA connectors Connect an SXGA graphics source to the SXGA PASS INPUT HD15 connector Connect the SXGA HD OUT HD15 connector to a video acceptor for example a plasma display as follows When connecting to an XGA acceptor RGBHV then connect to the acceptor s XGA connector When connecting to a component acceptor Y Cb Cr then connect as shown in Table 3 Table 3 HD15 PINOUT for HD PIN Signal 1 Cr 2 Y 3 Cb Connect the 12V DC power adapter to the power socket and connect the adapter to the mains electricity not shown in Figure 2 1 You do not have to connect all the inputs connect only those that are required 2 This PC input signal is not scaled but is available for pass through when the PC Source is selected 3 The PINOUT should be PIN 1 Cr PIN 2 Y and PIN 3 Cb with pins 6 7 and 8 as ground respectively KRAMER SIMPLE CREATIVE TECHNOLOGY Connecting the VP 419x1 Video to SXGA HD Scaler Composite Video Player pa Camcorder Computer Graphics Source Figure 2 Connecting the VP 419xl Video To SXGA HD Scaler Controlling the VP 419x 1
6. Kramer Electronics Ltd ah KRAMER USER MANUAL Model VP 419xl Video To SXGA HD Scaler Contents Contents 1 Introduction 2 Getting Started 2 1 Quick Start 3 Overview 4 Your VP 419x1 Video to SXGA HD Scaler 5 Connecting the VP 419xl Video to SXGA HD Scaler 6 Controlling the VP 419xl 6 1 Controlling via the Front Panel Buttons 6 2 Using the CONTROL Buttons 6 2 1 The MAIN MENU 6 2 2 The PICTURE Menu 6 2 3 The SETUP Menu 6 3 Controlling via the Infra Red Remote Control Transmitter 7 Technical Specifications Figures Figure 1 VP 419x1 Video To SXGA HD Scaler Front and Rear View Figure 2 Connecting the VP 419x1 Video To SXGA HD Scaler Figure 3 Infra Red Remote Control Transmitter Tables Table 1 Table 2 Table 3 Table 4 Table 5 Table 6 Table 7 Table 8 VP 419x1 Video To SXGA HD Scaler Front Panel Features VP 419x1 Video To SXGA HD Scaler Rear Panel Features HD15 PINOUT for HD The MAIN MENU Features The PICTURE Menu Features The SETUP Menu Features Infra Red Remote Control Transmitter Functions Technical Specifications of the VP 419x1 Video To SXGA HD Scaler e Re ua Roa O O VOo oo o oA AoA A Ya ROvwNNw0Noo anu un Introduction 2 1 Introduction Welcome to Kramer Electronics since 1981 a world of unique creative and affordable solutions to the infinite range of problems that confront the video audio and presentation professional on a daily bas
7. ON B gt Servicing the machines can only be done by an authorized Kramer technician Any user who makes changes or modifications to the unit without the expressed approval of the manufacturer will void user authority to operate the equipment B gt Use the supplied DC power supply to feed power to the machine B gt Please use recommended interconnection cables to connect the machine to other components 12 KRAMER SIMPLE CREATIVE TECHNOLOGY For the latest information on our products and a list of Kramer distributors visit our Web site www kramerelectronics com where updates to this user manual may be found We welcome your questions comments and feedback Safety Warning Disconnect the unit from the power supply before opening servicing Caution 9007 O 2 QU a Institute of Quality amp Control Kramer Electronics Ltd Web site www kramerelectronics com E mail info kramerel com P N 2900 000201 REV 3
8. anges and change the SETUP parameters see 2 section 6 2 3 6 5 Button Press to go up the menu list or adjust the PICTURE submenu values 8 see section 6 2 2 7 Button Press to go down the menu list or adjust the PICTURE submenu values see section 6 2 2 8 be S CV Button Press to select the composite video source 9 2 5 YC Button Press to select the s Video YC video source 10 lt UY COMP Button Press to select the component video source 11 D SXGA Button Press to select the SXGA source Table 2 VP 419xl Video To SXGA HD Scaler Rear Panel Features Feature Function 12 YC 4p Connector Connects to the s Video source 13 i CV RCA Connector Connects to the composite video source 14 E YRCA Connector 15 S CB RCA Connector Connects to the interlaced component video source 16 D CR RCA Connector 17 SXGA PASS HD15 Connector Connects to the VGA Y Pb Pr source 18 SXGA HD OUT HD15 Connector Connects to the SXGA or HDTV component video acceptor 19 12VDC 12V DC connector for powering the unit 1 Not compatible with progressive scan Y Pb Pr or HDTV 2 For component video connect all three connectors Y Cb Cr also known as YUV 3 This PC input signal is not scaled but is available for pass through when the PC source is selected Connecting the VP 419x1 Video to SXGA HD Scaler 5 Connecting the VP 419xl Video to SXGA HD Scaler Connect your VP 419xl as illustrated in the example in Figure
9. ds e An On Screen Display OSD for easy setup and adjustment accessible via the IR remote control and via the front panel buttons e A high performance adaptive 3D comb filter for precise color management e Per pixel motion compensated de interlacing for artifact free video images e Automatic detection for 3 2 pulldown for 24fps film source material e Frame rate conversion of 50Hz to 60Hz for PAL input signals e A Vertical Temporal VT Filter for removing jagged artifacts e Advanced color luminance transient improvement circuitry e APC Input connector for easy integration into an existing system e A built in procamp for convenient signal adjustment e A non volatile memory that retains the last settings used The machine is fed from an external 12V DC source making it suitable for field operation Control your VP 419x1 e Directly via the front panel push buttons e Remotely from the infra red remote control transmitter 1 The terminology XGA is used throughout this manual where this implies any RGBHV signal on an HD15 connector having a resolution from VGA up to SXGA Your VP 419x1 Video to SXGA HD Scaler To achieve the best performance e Connect only good quality connection cables thus avoiding interference deterioration in signal quality due to poor matching and elevated noise levels often associated with low quality cables e Avoid interference from neighboring electrical appliances and position your Kramer VP 419xl away fro
10. is In recent years we have redesigned and upgraded most of our line making the best even better Our 500 plus different models now appear in 8 Groups which are clearly defined by function Congratulations on purchasing your Kramer VP 419x1 Video To SXGA HD Scaler This product is ideal for e Projection systems in conference rooms boardrooms hotels and churches e Home theater up scaling The package includes the following items e VP 419xl Video To SXGA HD Scaler e Power adapter 12V DC input e Infra red remote control transmitter e This user manual Getting Started We recommend that you e Unpack the equipment carefully and save the original box and packaging materials for possible future shipment e Review the contents of this user manual Use Kramer high performance high resolution cables Quick Start This Quick start chart summarizes the basic setup and operation steps 1 GROUP 1 Distribution Amplifiers GROUP 2 Video and Audio Switchers Matrix Switchers and Controllers GROUP 3 Video Audio VGA XGA Processors GROUP 4 Interfaces and Sync Processors GROUP 5 Twisted Pair Interfaces GROUP 6 Accessories and Rack Adapters GROUP 7 Scan Converters and Scalers and GROUP 8 Cables and Connectors 2 Download up to date Kramer user manuals from the Internet at this URL http www kramerelectronics com 3 The complete list of Kramer cables is on our Web site at http www kramerelectronics com 1
11. m moisture excessive sunlight and dust No operator serviceable parts inside unit Warning Use only the Kramer Electronics input power wall adapter that is provided with this unit Warning Disconnect power and unplug unit from wall before installing or removing device or servicing unit 4 Your VP 419xl Video to SXGA HD Scaler Figure 1 Table 1 and Table 2 define the VP 419x1 Video To SXGA HD Scaler Y _ INPUT SELECTOR _Y_ RESET MENU ENTER cv YC Comp SXGA MW ooeSonne Oo IR O Video To SXGA HD Scaler VP 419 INPUTS SXGA Pass SXGA HD Our 12 VDC Figure 1 VP 419xl Video To SXGA HD Scaler Front and Rear View 1 For example model number AD2512C part number 2535 000251 4 KRAMER SIMPLE CREATIVE TECHNOLOGY Your VP 419x1 Video to SXGA HD Scaler Table 1 VP 419xl Video To SXGA HD Scaler Front Panel Features Feature Function 1 POWER Switch Switch for turning the unit ON or OFF 2 RGB RESET Button llluminates when the output resolution is set to RGB Press to set output to Y Pb Pr the button no longer illuminates Press and hold for more than 3 seconds to reset to VGA Press and hold for 10 seconds to reset to 480p 3 IR Receiver Lights when receiving signals from the remote control transmitter 4 MENU Button Displays the OSD menu see section 6 2 5 ci ENTER Button Press to accept ch
12. put resolutions 480p 576p 720p or 1080i SETUP Select the aspect output 3D enhance digital NR display and HV output see section 6 2 3 INFORMATION Displays the source resolution and software version EXIT Select to exit the menu 1 Press for 3 seconds to reset to VGA and press for 10 seconds to reset to 480p 2 The menu times out after 8 seconds 3 By pressing the RGB RESET button or via the OSD menu 8 KRAMER SIMPLE CREATIVE TECHNOLOGY Controlling the VP 419x1 6 2 2 The PICTURE Menu Table 5 defines the PICTURE menu Table 5 The PICTURE Menu Features Parameter Function Range Default CONTRAST Adjust the contrast From 0 to 63 58 BRIGHT Adjust the brightness From 0 to 63 31 COLOR Adjust the color From 0 to 63 31 HUE Adjust the hue From 0 to 63 31 DETAIL Adjust the sharpness From 0 to 63 10 RESET Select RESET and press ENTER to reset to the default parameters EXIT Select to exit to the MAIN MENU 6 2 3 The SETUP Menu Table 6 defines the SETUP menu Table 6 The SETUP Menu Features Parameter Function ASPECT Select between STANDARD 4 3 and 16 9 OUTPUT Select a PC RGB output or an HDTV Y Pb Pr output 3D ENHANCE Tur the 3D comb filter function ON or OFF DIGITAL NR Turn the digital noise reduction function ON or OFF DISPLAY Set to ON to display the input standard and the output resolution on the screen all the time Set to INFO
13. rpness Resolution output image scaling output mode 3D comb filter function and aspect ratio POWER SOURCE 12V DC 350mA DIMENSIONS 21 5cm x 16 3cm x 4 36cm 8 46 x 6 4 x 1 7 W D H WEIGHT 0 66kg 1 45lbs approx ACCESSORIES Power supply IR remote control OPTIONS 19 rack adapter RK 80 RK 80N 1 Specifications are subject to change without notice 2 All resolutions are outputted 60Hz except 576p which is outputted 50Hz 11 LIMITED WARRANTY Kramer Electronics hereafter Kramer warrants this product free from defects in material and workmanship under the following terms HOW LONGIS THE WARRANTY Labor and parts are warranted for seven years from the date of the first customer purchase WHOIS PROTECTED Only the first purchase customer may enforce this warranty WHAT IS COVERED AND WHAT IS NOT COVERED Except as below this warranty covers all defects in material or workmanship in this product The following are not covered by the warranty 1 Any product which is not distributed by Kramer or which is not purchased from an authorized Kramer dealer If you are uncertain as to whether a dealer is authorized please contact Kramer at one of the agents listed in the Web site www kramerelectronics com 2 Any product on which the serial number has been defaced modified or removed 3 Damage deterioration or malfunction resulting from i Accident misuse abuse neglec
14. t fire water lightning or other acts of nature ii Product modification or failure to follow instructions supplied with the product iii Repair or attempted repair by anyone not authorized by Kramer iv Any shipment of the product claims must be presented to the carrier v Removalor installation of the product vi Any other cause which does not relate to a product defect vii Cartons equipment enclosures cables or accessories used in conjunction with the product WHAT WE WILL PAY FOR AND WHAT WE WILLNOT PAY FOR We will pay labor and material expenses for covered items We will not pay for the following 1 Removal or installations charges 2 Costs of initial technical adjustments set up including adjustment of user controls or programming These costs are the responsibility of the Kramer dealer from whom the product was purchased 3 Shipping charges HOW YOU CAN GET WARRANTY SERVICE 1 To obtain service on you product you must take or ship it prepaid to any authorized Kramer service center 2 Whenever warranty service is required the original dated invoice or a copy must be presented as proof of warranty coverage and should be included in any shipment of the product Please also include in any mailing a contact name company address and a description of the problem s 3 For the name of the nearest Kramer authorized service center consult your authorized dealer LIMITATION OF IMPLIED WARRANTIES All implied warranties
15. to briefly display the input standard and the output resolution on the screen after a change is made Otherwise set to OFF HV OUTPUT Select ON to send H and V synchronization when Y Pb Pr is selected for the output EXIT Select to exit to the MAIN MENU 1 STANDARD will output the signal in the same aspect ratio as the input aspect ratio 4 3 and 16 9 will always output as 4 3 and 16 9 respectively regardless of the input aspect ratio 2 When a video player or a non standard video source is connected to the input the output picture may jitter If this occurs turn the 3D Comb Filter to OFF 3 H and V are always sent when RGB is selected at the output 9 Controlling the VP 419x1 6 3 Controlling via the Infra Red Remote Control Transmitter You can control the VP 419xl from the infra red remote control transmitter as Figure 3 and Table 7 define Table 7 Infra Red Remote Control Transmitter Functions Keys Function POWER Turn power ON or OFF DISPLAY Turn input standard and output resolution information display ON or OFF C VIDEO Select the composite video input S VIDEO Select the s Video input YCbCr Select the component video input PC Select the input PC to loop through VGA Set the output resolution to 640x480 SVGA Set the output resolution to 800x600 XGA Set the output resolution to 1024x768 SXGA Set the output resolution to 1280x1024 480p
Download Pdf Manuals
Related Search