Kompernass PDS 150 Operating and Safety Instructions
Contents
1. PDS 150 CE 2002 Operating and safety instructions Abh Fig 1 Abb Fig 2 PARKSIDE PARKSIDE PDS 150 BENCH GRINDER For grinding and sharpening metal tools Dear Customer We are delighted that you have decided to p yourself fully with the way the equipment works before you u tools correctly Please read the operating instructions i urchase our high quality PDS 150 Bench Grinder Please make sure you familiarise se it for the first time and that you understand how to handle electrical power below and the accompanying safety advice A carefully Use the equipment only as described and for the indicated purposes By doing this you will be able to work in complete safety and produce better results We hope you enjoy using your bench grinder FEATURES OF THE PDS 150 O Mounting holes 4x Wheel guard cover Protection shields Wheel edge cover Protection shield mount O Grinding wheel Workpiece support right O Machine side flange marked with notch e ON OFF switch Nut with notch Workpiece support adjustment screws Outside flange not marked O Workpiece support left O Left hand thread TECHNICAL INFORMATION ominal voltage 230V 50 Power consumption 150 watts 0 load speed 2 950 rpm Grinding wheel diameter 150 mm Grinding wheel width 16 mm Grinding wheel bore 12 7 mm Circumferential speed max 21 99 m s2. Weight 1 3 kg Sound pressure level 73 00 dB A Noise level determined for normal operation measured in accordance with DIN 45635 21 We reserve the right to make technical modifications to and changes to the appearance of the equipment in the course of further development without notice Hence no responsibility is accepted for any information such as dimensions instructions etc This does not affect your legal rights IMPORTANT SAFETY ADVICE A A Ensure that you observe the following safety instructions specifically for this equipment and in addition that you read the advice in the accompanying booklet called Safety advice before using the equipment for the first time A Not following the safety instructions and advice can lead to accidents electric shock injuries risks to health or burns This bench grinder is intended to be used exclusively for dry grinding Materials dangerous to health such as asbestos are not to be abraded Wear ear protectors Look after your health please wear safety glasses and a breathing dust mask e Always keep the mains cable away from the working area of the grinder and lead the cable away from the rear of the grinder The equipment is not to be used by people under 16 years old ARNING Danger of burning The workpiece gets hot during grinding Never touch the part being ground Allow the workpiece to cool sufficiently When grinding for longer periods stop grinding from time to time
3. 1029 1 2000 PEN 61029 2 4 1992 EN 55014 1 1993 A2 1999 EN 61000 3 2 1995 A2 1998 EN 55014 2 1997 EN 61000 3 3 1995 Manufacturer PARKSIDE Model type POS 150 Description BENCH GRINDING MACHINE Bochum 31 07 2002 Hans Komperna Managing Director d p JI wh Y LU m WARRANTY This piece of equipment is covered by a 36 month warranty as of the date of purchase The equipment was produced with the greatest of care and underwent thorough testing before delivery In the unlikely event of detecting a functional defect please return the equipment in its original packaging with the proof of purchase if available tothe closest service address Damage caused due to improper handling as well as regular wear of the parts are not covered by this warranty Beaver Electronic Services The Lodge Premier Business Park Long Street Walsall West Midlands WS2 9DY Tel 019 22 7255 54 Fax 01922 725417 WARRANTY This piece of equipment is covered by 36 month warranty as of the date of purchase The equipment was produced with the greatest of care and underwent thorough testing before delivery Inthe unlikely event of detecting a functional defect please return the equipment in its original packaging with the proof of purchase if available to the closest service address Damage caused due to improper handling as well as regular wear of the parts are not covered hy this warranty Irish Web Specialists 1 Verbena Ave
4. and allow the workpiece to cool before continuing bbb gt Db gt DPD AREA OF USE The PDS 150 Bench Grinder is intended for grinding and sharpening metal tools such as drills chisels etc and metal items We do not take any responsibility for uses other than those given here Similarly in this event the guarantee becomes null and void CASSEMBLY COMMISSIONING AND USE m ASSEMBLY IN Before commissioning for the first use the equipment must be fully assembled with all its parts Attach the eye shields the workpiece support left and the workpiece support right see Fig 1 The bench grinder must be mounted on to a robust level surface and if at all possible on to a fixed support e g working surface workbench Use the four mounting holes m POSITIONING WORKPIECE SUPPORTS AND EYE SHIELDS ensure safe working the workpiece supports and the eye shield mounts must be correctly positioned Check and correct the settings at frequent intervals to ensure even wear on the grinding wheel The clearance between the grinding wheel and the eye shield holder and between the grinding wheel p and the workpiece support or must be no more than 2 mm Pull out the mains plug and loosen the workpiece support adjustment screw for setting Bring the workpiece support close up to grinding wheel q until the wheel just not longer moves This is the correct setting Retighten the adjustment screw a
5. e is no one in the danger area CARE AND MAINTENANCE Always make sure that the mains plug is out of the socket before doing any work on the equipment The PDS 150 Bench Grinder does not generally require maintenance lean the bench grinder frequently For best results immediately after you have finished using it Do not allow any liquids to enter the hench grinder Use a soft cloth to clean the grinder Do not under any circumstances use petrol or strong solvents Store the grinder in a dry room Repairs are only to he carried out at a specialist electrical repair centre This electrical equipment complies with the relevant safety regulations Repairs may only be carried out by a specialist electrical repair centre using original spare parts otherwise injury could occur to the user You can find further practical tips on electrical tools in the accompanying booklet Safety Advice STATEMENT OF CONFORMITY We Komperna Handelsgesellschaft mbH Burgstr 21 D 44867 Bochum Germany hereby declare that this product conforms with the following EC regulations EC machine guideline 98 37 EEC EC low voltage regulations 73 23 EEC with change EC directive 93 68 EEC Electromagnetic compatibility 89 336 EEC with change EC directive 93 68 EEC Applicable harmonised standards DIN VDE 0741 08 63 DIN 66069 06 73 VBG 7n 01 93 EN 6
6. nd check using your hand that the grinding wheel movement is true and free If the grinding wheel q is worn so much that the above clearance can no longer be achieved even after adjustment of the workpiece support ele ur the eye shield mount then the grinding wheel must be changed m COMMISSIONING ZN Ensure that the equipment is switched off and that the ON OFF switch is in the 0 position Take note of the mains voltage The voltage must agree with that shown on the equipment rating plate equipment shown as 230 V can also be connected to 220 V ON OFF switch in position 1 equipment runs at a constant speed ON OFF switch in position 0 equipment is switched off m USE To grind metal tools or metal items place the workpiece on the workpiece support and slowly bring it close to the grinding wheel Carefully press the workpiece against the grinding wheel qp Too much pressure can lead to overloading of the bench grinder Grinding should be carried out only on the circumference of the grinding wheels CCHANGING A GRINDING WHEEL Always make sure that the mains plug is out of the socket before doing any work on the equipment and when it is out of use You must only use grinding wheels on which the manufacturer s information the type of adhesive dimensions and permitted speed agree with the technical information specified for this bench grinder Do not use any damaged or distorted gri
7. nding wheels If you install new grinding wheels carryout a ringing test before use Grinding wheels in good condition give a clear ringing noise when struck lightly with a plastic hammer Take off the wheel guard cover eye shield and the wheel edge cover and slacken the workpiece mount You must ensure that the left hand side of the bench grinder see Fig 2 has a left hand thread and the right hand side has a right hand thread The notched nut indicates the left hand thread The nut without notches corresponds to the right hand thread This ensures that the nuts can only be screwed off in the direction of rotation of the spindle w change the grinding wheels and reassemble all the components in the reverse order ZA WARNING 1 Do not interchange the flanges when attaching the grinding wheels see Fig 2 Use only the clamping flange supplied to mount the grinding wheels Central fixing holes in grinding wheels are not to he redrilled Never operate the bench grinder without the wheel guard cover eye shields or the wheel edge cover in place Always fully reassemble the grinder before use Check and correct the setting of the work piece supports and eye shield mounts at frequent intervals as described in the Section Positioning workpiece support and eye shields 5 After changing a grinding wheel the grinder must to be run for a test period under no load of at least 5 minutes Ensure that ther
8. nue Dublin 13 Tel 01 8 320492 Fax 01 8 39 68 29 PARKSIDE Essen Germany y www orfgen nm de
Download Pdf Manuals
Related Search