Kompernass KH 2346 User's Manual
Contents
1. In the chapter uninstall and repair is described how you can remove the software and in the event of problems reinstall the driver Connection When the driver and software installation is complete as described previously you can now connect the device Connecting the Hub e Insert the USB plug from the Hub into a vacant USB connector on your computer e nsert the red and green plugs from the Hub into the red and green audio sockets on your computer e You can now connect other USB devices for example a USB mouse or USB keyboard to the USB connectors on the Hub 2 The total power consumption must not exceed 500 mA otherwise it is possible that some devices will not function properly or not function at all The power consumption of the webcam amounts to 140 mA Connecting the headset e nsert the red and green plugs from the headset into the red and green sockets on the Hub Connecting the webcam e nsert the USB plug into the USB connector on the top of the Hub This will be recognized by the computer and the following message appears on the bottom right of the screen Found new hard ware It could be a few minutes before the message appears to indicate that the webcam has been installed and is ready for use Info The webcam has built in object lighting 4 white LEDs next to the lens These switch on and off automatically according to the lighting circumstances For this no con2. offset interfering light from behind When you have carried out all settings e Click on Apply to accept the setting and to continue to remain in this setting window e Click on to accept the setting and to close this setting window e Click on Cancel to reject the setting and close this setting window 15 Capture setting With the test programme you can capture simple audio video data in the media format AVI and with a suitable player play them back on your computer Here you only carry out settings for the capturing how you start the capturing is explained later under Capture function Uu Wok urrie ye urid E ols Re Devices ptos Capture Hep Start Capture Capture Audio doed CAEN e Click on Capture in the menu list When the appropriate selection Hips open select the function Master Stream in order to specify as the main data stream the audio or video signal or in regard to this that there are no encounters with predefinitions None Select the function Set Frame Rate to set the transmission rate Images per second When you place a tick in the selection box Use Frame Rate this value will be used Select the function Capture Time Limit to enter a maximum time for the capturing i e 10 seconds When you place a tick in the selection box Use Time Limit any capturing started in future will stop after this entered time silo
3. 3 b KOMPERNASS GMBH BURGSTRASSE 21 D 44867 BOCHUM www kompernass com ID Nr KH2346 10 07 V 1 M MULTIMEDIA HUB KH 2346 MULTIMEDIA HUB a Operating instructions SilverCrest KH 2346 Em CONTENT PAGE Intended Use 2 System requirements 2 Safety instructions 3 Technical data 4 Package contents 5 Device description 5 First install the driver 6 Connection 7 Device use 8 Amcop test software 9 Uninstall or repair 20 Cleaning 21 Disposal 21 Warranty amp Service 22 CE Conformity 23 Importer 23 Read the operating instructions carefully before using the appliance for the first time and preserve this booklet for later reference Pass the manual on to whomsoever might acquire the scale at a later date ae MULTIMEDIA HUB KH 2346 Intended Use This product is designed for use on a PC or notebook in a private home environment It is not intended for use on other computers nor is it intended for business or industrial purposes The product is usable as an extension and add on of USB and sound card connections as well as for internet telephones video chat and as a webcam System requirements This product requires a PC or notebook with the following minimum system requirements Operating System Windows 98SE ME 2000 XP Vista Processor Pentium 200 or higher Hard disc min 20 MB free hard disc space Drive CD ROM for installation CD Memory min 32 MB RAM Sound Au
4. at packaging remnants are removed Device description Webcam Snapshot button Webcam Lens turn the white ring to focus Webcam Swan neck Webcam USB to HUB plug HUB Red and green audio plug to the computer HUB USB to PC plug Headset Microphone Headset Earbud Headset Volume control Headset Audio plug to the HUB HUB Audio socket for the Headset HUB USB connection for other USB devices HUB USB connection for the Webcam oe First install the driver Important Do not connect the camera or hub to the USB connection on your computer until the relevent drivers have been installed Otherwise your computer system may possibly install inappropriate generic drivers automatically e Switch your computer on and start Windows Close all application programmes that may be running e Insert the installation CD supplied with the device The installation now starts automatically from the CD If it does not right click with the mouse on the CD ROM drive in which the installation CD is located and then select Autoplay Welcome io iha eile heyli wira lou WS PE Cea 11 124 Click on Nexf as soon as the installation window appears The installation will now run automatically Should a message about the Windows Logo Test appear ignore it and click on Continue e Click on Finish as soon as this window appears With this the installation is complete
5. dio IN OUT VIDEO VGA Standard suitable for DIRECTX Interfaces USB Internet connection only when operating as a webcam video chat or internet telephone Safety instructions Do not open device parts there are no user serviceable elements inside Repairs must only be carried out by authorized specialists or the service department e Profect the camera from extreme temperatures moisture dirt and dust Do not touch the camera lens with bare fingers If you do the camera lens could become clouded NEVER submerse the appliance in water Wipe it off only with a soft dry cloth Do not pull the USB plug out of the computer or the camera out of the hub while the programme is running If you do it could result in data loss e n unfavourable circumstances the installation of new drivers onto your computer could cause system crashes and the loss of data Therefore before every installation save any important data on an external storage facility Be aware of the fact that by using the camera in video chat and internet telephone applications you are allowing insight from out side into your personal sphere Always disengage the camera and headset after you have finished this type of usage Many damaging software applications viruses trojans etc may be capable of switching the camera on unnoticed Do not use the camera in order to record or transmit the image of other people without their knowledge This would violate cri
6. e A test software is also installed with the driver with which you can check the camera as well as for test purposes prepare and save simple video recordings Starting test software Double click on the amcap symbol on the Windows desktop Or you can select from the start menu under Programmes the folder USB PCCamera and there click on amcap om Checking the camera After the test programme is started the camera image appears after a few seconds in a small flip open window x Fle Devices Opiom Capture Hep Z5ME USE FC Camera evti weitere Videotreiber v Ihr Soundtreiber Crus Logic USE OVFS Source If you do not see an image e Click on Devices in the menu list Check to see if the input ZSMC USB PC Camera is present and that there is a tick in front of it If not click on this input f no input is present reinstall the driver e Also check in the amcap test programme menu Options if there is a tick in front of the Preview menu item e check in the Windows device manager under Image proces sing devices if the input ZSMC USB PC Camera is present If not reinstall the driver 10 Setting the microphone sensitivity Click on pfions in the menu list When the appropriate selection flips open select the Audio Capture Filter function The setting window Properties now appears Properties AudiolnputM
7. e of abusive and improper handling use of force and internal tampering not carried out by our authorized service branch Your statutory warranty claims are not restricted by this warranty 5 CE Conformity This device has been checked and approved regarding conformance with the fundamental requirements and other relevent provisions of the EMV directive 2004 108 EG Importer KOMPERNASS GMBH BURGSTRASSE 21 D 44867 BOCHUM www kompernass com 25 24 ainyouBbis ey0q suoydajey Aayuno7 UMOL AID TEENI 1511 wpu 1501 BJM 18pues OP ISSIDISA ISAUW MMM dus sajps 1n04 Apu NOK ans 9YDW ulHOu 29141419S v UHAA yY2NO4 woo sspuaduioy yn oddns lowe ul 496 sp ld sipda 9914 so sojupinnf 18p10 ul 8919 282 0 80 1119 282 0 80 191 OVEC HJ anH VIGIWILINW PH 930 css 153J J3A IS i sup yddo sy UHAA pup SIU4 INO 1 91diuo AJUD11D AA Description of fault
8. e setting and to close the setting window Click on Cancel to reject the setting and to close the setting window e When you now click on Save Capture Video the data will be saved under the previously set data name fo Uninstall or repair When you want to remove the software uninstall or reinstall in the event of a malfunction first proceed as described in the chapter Driver installation The software automatically recognizes that this is already installed and therefore accesses as opposed to the initial installation the following selection Click on Repair when you want to reinstall the driver and test programme i e because the device manager could not find the webcam or no image is displayed e Click on Remove when you want to remove the driver and the test programme from your computer e Click on Modify when you want to add new programme features or remove already installed programme features Reboot your operating system if after installing the driver again the camera is still showing no image If this does not improve the situation then there is a conflict with some other computer component In this case contact your computer dealer 20 Cleaning Cleon the device with a dry or lightly moistened cloth only To avoid potential damage to the upper surfaces do not use any abrasive or chemical cleaning agents Do not submerge any of the device components in any f
9. ixer Properties Master Input Mix or Pin Line Input Mix 2 V Enable Pin Line ES v Here you can set the sensitivity of the microphone input on your PC e Select Microphone as the audio source on the female header Push the volume control completely up p arrow Place a tick in the window Enable When you have carried out all settings Click on to accept the settings 11 Selecting sound quality e Click on pfions in the menu list When the appropriate selection flips open select the Audio Format function The setting window Sound Selection now appears Sound Selection Name Format PEM Attributes 44 100 kHz 16 Bit Stereo 172 kb sec Cancel Here you can set the audio quality of the sound recording The optimal settings are preset at the factory as can be seen from the picture If you want to try a few settings e Under Form f you can select other preset audio formats e Under Attributes you can select the desired setting from other quality levels e Click on Save 05 to give your personal selection a name and then to save it e Click on Name to select from a list of previously saved settings e Click on Remove if you want to delete a selected setting from the list When you have carried out all settings e Click on to accept the settings Selecting image quality e Click on Optio
10. minally protected rights e This product is not designed to be used by persons including children with limited physical sensorial or mental abilities or who lack experience and or knowledge unless of course for their own safety they are 3 supervised by a competent person or receive instructions from such a person on how to use the device Children should be supervised in order to make sure that they do not play with the product Technical data USB Webcam Sensor Resolution Video format Max Pixel Lens USB Standard Power consumption Transmission Functions Features USB HUB Number of ports USB Standard Power supply Interfaces Headset Frequency response Sensitivity Impedance Power input 1 4 CMOS max 640 x 480 VGA 24 bit True Colour 1 3 M F 2 2 1 1 140 mA 30 images per second with 320 x 240 15 images per second with 640 x 480 automatic whitening adjustment manual focusing Snapshot button 4 white LEDs for lighting 3 1 of which is for the webcam 2 0 via USB connection from the computer 2 x 3 5 mm jackplugs jackplug sockets 20 Hz 20 kHz 111 dB 3 32 Ohm 100 mVV max a Cable lengfh approx 2m Interfaces 2 x 3 5 mm jackplugs Package contents 1 x USB Webcam Camera 1 x USB Hub 1 x Headset 1 x Installation CD 1 x Operating Instructions e Check to ensure that the device is undamaged all component parts are present and th
11. nections or settings are required Device use When the device has been properly installed it is registered as such in the PC Applications which need this device as for example internet telephones or a video chat programme and are automatically accessed The operation then arises from the respective application Hub use e The operation of the Hub is restricted to the connecting and discon necting of the respective USB device Whether this is also possible in the current operation is solely dependent on the computer and Ba operations system not on the Hub First make certain of this by means of your computers documents otherwise it could lead to data loss Headset use Put the headset on in such a way that the neck yoke is supported over the collar Subsequently bend the flexible neck of the micro phone so that it is close to your mouth With the volume control you can set the headphone volume Webcam use Start the respective application video chat webcam for which you want to use the camera and select a function there with which the current camera image is displayed for adjustment Bend the flexible swan neck of the camera in the direction that you want the camera to capture Turn the lens until the image sharpness on the test image in your application is satisfactory With the snapshot button you can capture an individual fixed image if your application supports this Amcap test softwar
12. ns in the menu list When the appropriate selection flips open select the Video Capture Pin function A setting window for the video properties now appears Properties Stream Format Video Format r Compression Video Standard None Frame Rate 130 000 El Frame Interval zj pu B onta T P Frame nterval Color Space Compression RGB 24 Output Size Quality 320 x 240 Cancel Apply Here you can set the quality of the image recording The optimal settings are preset at the factory as can be seen from the picture If you want to try a few settings e Under Frame Rate you can now set the image quality The higher the value the more power that the PC must provide e Under Output Size 320 x 240 and 480 x 640 are meaningful settings Other sizes are admittedly setable however they have no effect e Under Color Space Compression you can carry out settings on the colour presentation according to personal preference When you have carried out all settings e Click on Apply to accept the setting and to continue to remain in this setting window e Click on to accept the setting and to close this setting window e Click on Cancel to reject the setting and close this setting window 13 Setting the image e Click on pfions in the menu list When the appropriate selection flips open select the Video Capture Filter function Ano
13. orm of liquid as this could damage the device Disposal Do not dispose of the appliance in your normal domestic waste This product is subject to the European guideline mms 2002 96 Dispose of the appliance through an approved disposal centre or at your community waste facility Observe the currently applicable regulations In case of doubt please contact your waste disposal centre Dispose of all packaging materials in an QD BA environmentally friendly manner 1 Warranty amp Service The warranty for this appliance is for 3 years from the date of purchase Should you have grounds for complaint despite our high quality standards please contact our Service Hotline In the event that your complaint cannot be resolved over the telephone you will receive from them e o processing number RMA number as well as an address to which you can send your product for warranty processing In the case of a mail in shipment please enclose a copy of the purchase receipt sales slip The appliance must be securely packed and the RMA number clearly visible Shipments without an RMA number can not be processed Note The warranty provisions cover only material or factory defects The warranty provisions do not cover e worn ouf parts e damage to breakable paris like switches or rechargeable batteries This product is for private use only and is not intended for commercial use The warranty is void in the cas
14. s When you have carried out the respective settings e Click on to accept the setting and to close the respective setting window e Click on Cancel to reject the setting and to close the setting window Capture function When you have carried out the Capture settings as described previously you can use this function to start the capturing stop the capturing and save this capturing as data To start the capturing Mi AMGAP C Dokurnerite und E 1 nix L l Click on Capture in the menu list When the appropriate selection Hips open select the function Start Capture Click on to now start the capturing Click on Cancel to cancel the start m To stop the current capturing Click on Capture in the menu list e When the appropriate selection flips open select the Stop Capture function The capturing will now stop To save the capturing as data 18 Click on File in the menu list When the appropriate selection flips open select the Set Capture File function to select the folder where the data is to be filed and enter a data name select the Allocate File Space function to access the setting window Set File Size There you can preset a maximum size for your captu red data Should this already exist then by clicking on K the data is lost When you have set the data size Click on 0K to accept th
15. ther setting window for the video properties appears Properties Camera Controls Image Control Brightness Contrast Gamma Hue _ Saturation Sharpness WhiteBalance Red i Green Blue Auto Enable Auto Mode Control Exposure 1 AUTO USB Bandwidth AUTO Default Reset Save Restore 3 J7 Vertical Flip Color Enable Mirror Flip Backlight Comp Flicker Out door s Hz C 60Hz Auto Enable wv Auto Enable M Cancel Apply You can change various image properties with the slider control accor ding to personal preferences e When a tick is placed in the selection box Auto Enable the optimal settings are automatically applied Click on Restore to automatically apply the optimal settings for all slider controls Click on Reset to cancel the changes that you have made Click on Save to permanently save the changes that you have made 14 You can set the image effects as indicated with the squared selection boxes e Select under No Flicker the setting 50Hz if you are using electrical lighting on the image object e Select Vertical Flip if you want to stand the image on its head e Select Mirror Flip if you want to mirror the image horizontally e Select Backlight Comp if you want to
Download Pdf Manuals
Related Search