Kohler K-3106-F2 User's Manual
Contents
1. 86217 2 AA C 4 Kohler Co Kohler WI STACKING MULTIPLE UNITS P Top Unit 6 CAUTION RISK OF PERSONAL INJURY OR PRODUCT DAMAGE The following cautions apply to stacking on freestanding bases N The higher units are stacked the more unstable the assembly becomes If units are utilized in a manner where most of the weight is placed in the upper part of the cabinet the units may become unstable If units are stacked above 60 high the assembly becomes very unstable Drill holes 1 4 Ey the top unit Bottom Unit NOTE When stacking units on wall mount bases make sure to secure each cabinet to the wall NOTE Only the case drawers may be stacked with the storage cases or other case drawers The case drawers have two equal sized drawer compartments Stack the two units on top of one another Make sure units are square to each other Measure in from the front edge of the top unit approximately 1 and approximately 1 from either side Mark each location Drill a hole at each mark through the top of the bottom unit and approximately 1 4 into the bottom of the top unit Do not drill completely through the bottom of the top unit Make sure to use a drill of adequate diameter to accommodate fasteners not provided Secure with fasteners not provided Kohler Co Kohler WI 5 86217 2 AA C 86217 2 AA C 6 Kohler Co Kohler WI Ko2. cleat is level and predrill holes into the wall to align with the holes in the cleat Use a drill of adequate diameter to accommodate fasteners not provided Secure cleat to wall with fasteners not provided Kohler Co Kohler WI Cleat _ 2 1 2 3 1 8 Horizontal Drawer Unit Cleat 21 2 3 1 8 Vertical Drawer Unit 86217 2 AA C 4 Pre Installed Cleat Position the drawer unit on the wall so the cleat that is pre installed on the back of the unit rests on the cleat on the 7 d Drawer Unit wall Make sure the unit is centered on the cleat Measure 1 2 up from the bottom inside edge and approximately 1 2 from either ade Drill a hole at each location Wall Cleat through the back of the box spacer block and into the wall Use a drill of adequate diameter to accommodate fasteners not Es provided Finished Wall Secure with fasteners not provided DRAWER INSTALLATION Wax 5 Eyes Drawer e P we Wax drawer guides with wax crayon provided In order to preserve the finish of this piece wax the drawer glides twice a year Insert drawers CAUTION RISK OF PERSONAL INJURY OR PRODUCT gt DAMAGE Be careful when pulling out drawers Drawers slide completely out of the cabinets Provide support with your hand underneath the drawer when inserting or removing drawers
3. KOHLER TELLIEUR STORAGE DRAWERS INSTALLATION INSTRUCTIONS MATERIALS NEEDED e Level e Square e Drill e Measuring Tape Pencil Safety Glasses Fasteners see steps 3 4 amp 6 Wax Crayon provided BEFORE YOU BEGIN 1 Unpack the drawer unit and drawers and inspect for damage DRAWER PULL INSTALLATION 2 Drawer pulls come installed backwards Remove pulls and reinstall properly Securely hand tighten Pull Drawer INSTALLATION OF DRAWER UNIT TO WALL 3 NOTE Before proceeding verify whether the cabinet is a filler unit 2 equal sized drawer compartments a 2 drawer vertical unit one small and one large drawer or a 3 drawer unit NOTE Vertical units may not be installed horizontally and horizontal units may not be installed vertically 86217 2 AA C 1999 Kohler Co Case DRAWER UNITS Determine the desired location of the case drawer unit 3 1 8 Measure down 3 1 8 from where the top edge of the case drawer will be located and 2 1 2 in from where the left edge will be located Make a mark at this point While holding the cleat with the largest side facing away from the wall align the left hole in the cleat with the mark on the wall Make sure cleat is level and predrill holes into the wall to align with the holes in the cleat Use a drill of adequate diameter to accommodate fasteners not provided Secure
4. cleat to wall with fasteners not provided 2 DRAWER VERTICAL UNITS Determine the desired location of the drawer unit 3 1 8 Measure down 3 1 8 from where the top edge of the storage unit will be located and 2 1 2 in from where the left edge will be located Make a mark at this point While holding the cleat with the largest side facing away from the wall align the left hole in the cleat with the mark on the wall Make sure cleat is level and predrill holes into the wall to align with the holes in the cleat Use a drill of adequate diameter to accommodate fasteners not provided Secure cleat to wall with fasteners not provided 86217 2 AA C 2 2 Drawer Vertical Unit N 2 1 2 Cleat o o Case Drawer Unit 2 1 2 Cleat o Kohler Co Kohler WI 3 DRAWER UNITS Determine whether you have a horizontal or vertical drawer unit Check orientation of large drawer to verify NOTE When installing a horizontal unit the large drawer must be installed on the left hand side Determine the desired location of the drawer unit Measure down 3 1 8 from where the top edge of the drawer unit will be located and 2 1 2 in from where the right edge will be located Make a mark at this point While holding the cleat with the largest side facing away from the wall align the right hole in the cleat with the mark on the wall Make sure
5. hler Co Kohler WI 7 86217 2 AA C CALL US FOR HELP Questions Problems First review the installation instructions to ensure correct installation For additional assistance in the USA call our Customer Service Department for direct help You may also contact us at our web site THEBOLDLOOK OF KOHLER 1 800 4 KOHLER www kohlerco com 86217 2 AA C 8 Kohler Co Kohler WI
Download Pdf Manuals
Related Search