Kobe Range Hoods RA3830SQD User's Manual
Contents
1. CONTENTS OF PACKAGE 5 CAREFULLY UPON RECEIVING We must be notified in writing of any damages and or missing parts within the allocated days upon receipt of package s Contact your local KOBE dealer or distributor or call KOBE for the time limit CLAIMS WILL NOT BE ACCEPTED AFTER THE ALLOCATED DAYS NOTE ITEMS WERE THOROUGHLY TESTED AND CAREFULLY PACKED IN OUR FACTORY Products must be returned in good working condition with ALL original parts and documentation packed in ALL original cartons fillers and shipping cartons A restocking fee of 25 will be charged for all approved return s EXCHANGES OR RETURNS MAY NOT BE ACCEPTED IF ANY PACKAGING IS MISSING MAKE SURE TO INSPECT THE HOOD FOR DAMAGES AND DEFECTS BEFORE INSTALLATION Appearance flaws of the hood found after installation and not affecting hood performance is not covered under our warranty for returns or exchanges Service visits not covered under warranty will carry a service charge A Before Installation Return for exchange or refund please see above for acceptable returns B After Installation NO exchange or refund 18 WARRANTY CERTIFICATE KOBE Range Hoods Inc warrants all products manufactured or supplied by it to be free from defects in workmanship and materials Its obligations pursuant to this warranty are limited to a period of two years from the date of purchase and to the repair or replacement at its option and subject to the terms2. Halogen Light Processor Board Box ME ME 12 2 20 1 0401 0120 01 1 0402 120 04 1 0402 0120 40 Round Head Screw TS 1 8 x 3 8 Control Unit Control Board Charcoal Filter Set Charcoal Filter Mesh Filter Safety Screen Oil Container Round Safety Screen Screw Plastic Plate 1 1 0404 0401 ee C1 0603 0302 F 0201 Optional Duct Cover NO DESCRIPTION CCL MODELISIZE RA1020DC 15 MODEL NO RA3830SQD RA3836SQD PG CIRCUIT DIAGRAM MODEL NO RA3830SQD RA3836SQD CAPACITOR 3 5 3 50 250 oron YELLOW Z POWER RECEP OCLE mi J z tt 2 GP ELECTRONIC CONVERTER 2 al le Elo B E Ea Els BLACK BROWN RED ORANGE YELLOW GREEN BLUE 17 DISCLAIMER 1 CAREFULLY INSPECT ALL ITEMS FOR DAMAGES BEFORE ACCEPTING DELIVERY NOTE ANY DAMAGES ON THE FREIGHT BILL OR EXPRESS RECEIPT REQUEST NAME AND SIGNATURE OF THE CARRIER S AGENT AND KEEP COPY TO SUPPORT YOUR CLAIM Upon acceptance of items owner assumes responsibility for its safe arrival Damages should be reported to carrier and a claim filed Failure to do this could result in the carrier refusing to honor your claim The carrier will furnish you with necessary forms for filing a claim DAMAGES CAUSED DURING TRANSIT ARE NOT COVERED UNDER OUR WARRANTY PLEASE INSPECT
3. Stainless Steel Back Panel SSP36 36 x 1 10 x 32 Net Gross RA3830SQD 36 3 40 7 RA3836SQD 39 6 44 0 QuietMode Low Medium High 150 200 330 400 2 0 2 8 4 0 4 6 In House Test Static Pressure 0 Specifications subject to change without notice 13 5 1 8 130 MEASUREMENTS 8 DIAGRAMS All inch measurements are converted from millimeter Inch measurements are estimated All measurements in are millimeters FOR UNDER THE CABINET Xe 9 7 NY 7 30 Knockout Holes A 36 Knockout Holes A amp B FOR STAND ALONE WITH OPTIONAL DUCT COVER 44 3 4 1136 Hood Mounting Bracket Duct Cover Mounting Bracket 3 4 20 7 Sg v6 QL LL 21 2 amp I oO ____ __ gt ____4 4 1 16 104 4 1 16 104 9 3 8 238 14 PARTS LIST MODEL NO RA3830SQD RA3836SQD DESCRIPTION Hood Casing MODEL SIZE PART NO RA3830SQD 10 03300 F RA3836SQD 10 03360 F Air Chamber Air Chamber Top C1 0102 0770F Air Chamber Side Air Chamber Opening C1 0251 0092 02 Motor Right Motor Left Impeller Right Impeller Left Impeller Plastic Cover Oil Tunnel Flat Head Screws 3 16 x 5 8 Bottom Casing OD RA3830SQD RA3836SQD Halogen Light 12V 20W Max Capacitor Transformer Motor Transformer
4. and conditions stated below of any component part which its examination shall disclose to be so defective TWO YEAR WARRANTY SERVICE PERIOD Any covered failure occurring within two years of original purchase arising from defective workmanship or material in manufacture will be repaired or at our option the unit will be replaced free of charge by an authorized KOBE Range Hoods Agent or KOBE Range Hoods as applicable Keep proof of purchase or original invoice handy for inspection If the range hood is sold by the original purchaser during the warranty period the new owner 15 protected until expiration of the original purchaser s warranty CONDITIONS The following conditions apply only in relation to the warranty expressly given in this certificate 1 This warranty applies only a within U S A and Canada b to range hoods used for PRIVATE SINGLE FAMILY USE if used for COMMERCIAL or MULTIPLE FAMILY USE or other purposes warranty will be voided 2 Repair of any fault to be provided under this warranty shall not be provided a if the identification number attached to the range hood has been altered rendered illegible or removed b if notice of the defect has not been given within the period applicable c for failure of light bulbs d for physical damage e for surfaces damaged by use of improper chemical cleaning agents f if the appliance has been i subject to misuse abuse negligence accident incorrect installa
5. charcoal filter set out Remove oil container round by turning counter clockwise Wash with warm soapy water Dry completely before returning into place rack dishwasher safe 11 To Replace Light Bulb CAUTION HALOGEN LIGHT UNIT MAY BE HOT WAIT UNTIL UNIT IS COOL 1 Make sure all control switches are off and range hood is unplugged 2 Use flat head screwdriver to pop out the protective covering as shown on Figure 13 3 Gently pull out the defective light bulb and discard Light bulb should be 12V 20W maximum Refer to Figure 14 Push bulb securely into light socket 4 Replace protective cover 5 Plug in range hood Figure 13 Figure 14 12 SPECIFICATIONS MODEL SIZE COLOR VOLTAGE NUMBER OF MOTORS DESIGN FAN TYPE EXHAUST CONTROL HALOGEN LIGHT HOOD DIMENSION W x D x H OPTIONAL ACCESSORIES WxDxH WEIGHT lbs SPEED Air Capacity cfm Sone RA3830SQD 30 RA3836SQD 30 430 Commercial Grade Stainless Steel 120V 60Hz 2 18 Gauge Seamless Twin Turbine Impeller Ductless with Charcoal Filter Set Electronic Control 4 Buttons 10 Second Standby Startup 30 Second Delay Shutoff 12V 20W x 2 RA3830SQD 29 3 4 x 20 1 2 x 5 1 8 RA3836SQD 35 1 4 20 1 2 x 5 1 8 1 Two Piece Adjustable Duct Cover RA1020DC 10 5 8 x 9 1 8 22 7 8 39 5 8 2 30 Stainless Steel Back Panel SSP30 30 x 1 10 x 32 3 30
6. rubber stands provided with two 4x8 mm screws provided to the back of the hood WALL STUDS be Figure 5 Figure 6 3 Attach the hood mounting bracket to the back of the hood with six 3 16 x 3 8 mm screws provided as shown in Figure 7 4 Use the references on Table 2 and the measurements on page 14 to decide the level of the hood Position two mounting screws not provided on the wall leaving 1 8 away from the wall Refer to Figure 8 9 Mounting Screws Figure 7 Figure 8 Align hood mounting bracket to the two screws on the wall and hook hood into place Tighten screws to secure hood to the wall CAUTION MAKE SURE THE HOOD IS SECURE BEFORE RELEASING Duct Cover Installation Mark the position of the duct cover mounting bracket Use reference E from Table 2 and measurements on 14 Attach and secure duct cover mounting bracket with two screws not provided Refer to Figure 9 NOTE Inner duct cover will cover the duct cover mounting bracket Connect electrical wires Refer to Wiring to Power Supply If necessary to hide electrical wire connections push wires back into the wiring box Access the wire connections underneath the hood by removing the bottom casing Before reattaching the bottom casing make sure wires do not slip between motors impellers or any moving parts to prevent any damage NOTE Be careful when using electrical screwdriver damage to the hood
7. D THE FOLLOWING INFORMATION FOR YOUR RECORD Model No Serial No Purchased Date Purchased From IMPORTANT PLEASE KEEP A COPY OF YOUR SALE RECEIPT OR INVOICE HANDY WHEN REQUESTING FOR SERVICE 21
8. KORBE KOBE Brand Range Hood Model No RA3830SQD RA3836SQD RA 038 SERIES 5 HEIGHT RECIRCULATING HOOD INSTALLATION INSTRUCTIONS AND OPERATION MANUAL READ AND SAVE THESE INSTRUCTIONS CONTENTS Important Safely INSUMUCUONS s1022 s22sesueestseuionesvdentnreanerededaseneneiedadagetendoeducioeean s 1 Components Of 3 IS All AMON ae 4 Under Cabinet Installation av 44424444 5 Stand Alone 7 Operating INSTITUTIONS vvs 10 MANENGEN 11 SPECMCa ONS EE A A 13 Measurements amp 14 PS US 15 Circuit Diag EE EE 17 Mae UO eee Uae teat ea 18 MV ARAN aden 19 PFOGUCL lt 21 READ ALL INSTRUCTIONS CAREFULLY BEFORE STARTING ALL WIRING MUST BE DONE BY A PROFESSIONAL AND IN ACCORDANCE WITH NATIONAL AND LOCAL ELECTRICAL CODES US 221547 IMPORTANT SAFETY INSTRUCTIONS PLEASE READ THIS SECTION CAREFULLY BEFORE INSTALLATION WARNING TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK OR PERSONAL INJURY OBSERVE THE FOLLOWING 1 Installation and electrical wiring must be done by qualified professionals and in accorda
9. al Fire Protection Association NFPA and the American Society for Heating Refrigeration and Air Conditioning Engineers ASHRAE and code authorities 4 Activating any switch may cause ignition or an explosion WARNING A amp ELECTRICAL SHOCK HAZARD Can result in serious injury or death Disconnect appliance from electric power before servicing If equipped the fluorescent light bulb contains small amounts of mercury which must be recycled or disposed of according to Local State and Federal Codes COMPONENTS OF PACKAGE Must Keep all material for returns or refunds Range Hood Box Duct Cover Box Sold Separately A KOBE Range Hood F KOBE Duct Cover Model No RA1020DC Warranty Registration Card G Screws Package C Instructions Manual H Duct Cover Mounting Bracket D Plastic Plate 1 Hood Mounting Bracket Charcoal Filter Set Model No RH CF01 Charcoal Filter x 2 Mesh Filter x 2 Safety Screen x 2 Oil Container x 2 Screw x 2 F Inner Duct Cover Outer Duct Cover KOBE KOBE Brand Range Hood Model No RA3830SQD 3 16 x 3 8 mm 6 pcs Rubber Stand 2 pcs Only used with purchase of duct cover Attached to hood INSTALLATION PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING Calculation before Installation Calculate the length of the installation before installing the hood All calculation is measure in i
10. arranty of merchantability and fitness for purpose imposed on the sale by the laws of the state of sale are limited to two year from the date of original purchase Some states do not allow limitations on the duration of implied warranties This warranty gives you specific legal rights and may also have rights which vary from state to state SERVICE For service contact KOBE Range Hoods Inc 4934 Walnut Grove Avenue Suite 202 san Gabriel CA 91776 U S A Tel 626 309 1356 Fax 626 309 1366 Email customerservice koberangehoods com www KobeRangeHoods com 20 PRODUCT REGISTRATION Register Your Product Any covered failure occurring within two years of original purchase arising from defective workmanship or material in manufacture will be repaired or at our option the unit will be replaced free of charge by an authorized KOBE Range Hoods Agent or KOBE Range Hoods as applicable Keep proof of purchase original invoice handy for inspection If the range hood is sold by the original purchaser during the warranty period the new owner is protected until expiration of the original purchaser s warranty See warranty section for complete warranty coverage information This appliance has been manufactured tested and inspected to the standards required by KOBE Range Hoods PLEASE MAIL IN YOUR WARRANTY REGISTRATION CARD AND PROOF OF PURCHASE TO KOBE Range Hoods Inc 4934 Walnut Grove Avenue Suite 202 san Gabriel CA 91776 RECOR
11. green to house wires and cap with wire connectors Connect according to color black to black white to white and green to green Test the operation of the hood before moving on to next step Make sure power is supplied to the hood Final Assembly 7 Turn power ON in control panel Check all lights and fan operation 8 Make sure to leave this manual for the homeowner STAND ALONE INSTALLATION This installation only applies with the purchase of an optional duct cover Model RA1020DC SAFETY WARNING HOOD MAY HAVE VERY SHARP EDGES PLEASE WEAR PROTECTIVE GLOVES IF IT IS NECESSARY TO REMOVE ANY PARTS FOR INSTALLING CLEANING OR SERVICING Preparation before installation Temporarily wire the hood to test for proper operation before installing Peel protective film off the hood and the duct cover if any If necessary prepare back wall frame with cross framing lumber for secure installation Using references on Table 2 and measurements on page 14 decide the level of the lumber Refer to Figure 5 Hood Installation CAUTION If required to move the cooking range to install the hood turn off the power on an electric range at the main electrical box SHUT OFF THE GAS BEFORE MOVING A GAS RANGE 1 Remove the five screws at the center of the hood top Use the five screws to attach plastic plate onto the hood as shown in Figure 6 NOTE Disregard the hole through the plastic plate 2 If necessary attach two
12. may occur Slide the inner duct cover up 2 inches before sliding entire duct cover onto the hood Refer to Figure 10 Figure 9 Figure 10 Adjust the height of the inner duct cover to the duct cover mounting bracket Secure inner duct cover with two 4x8 mm screws provided as shown in Figure 11 Attach Together Figure 11 10 Fasten outer duct cover to plastic plate on the hood with four 4x8 mm screws provided Wiring to Power Supply SAFETY WARNING RISK OF ELECTRICAL SHOCK THIS RANGE HOOD MUST BE PROPERLY GROUNDED MAKE SURE THIS IS DONE BY SPECIALIZED ELECTRICIAN IN ACCORDANCE WITH ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL CODES BEFORE CONNECTING WIRES SWITCH POWER OFF AT SERVICE PANEL AND LOCK SERVICE PANEL TO PREVENT POWER FROM BEING SWITCHED ON ACCIDENTALLY Connect three wires black white and green to house wires and cap with wire connectors Connect according to color black to black white to white and green to green Test the operation of the hood before moving on to next step Make sure power is supplied to the hood Final Assembly 11 Turn power ON in control panel Check all lights and fan operation 12 Make sure to leave this manual for the homeowner OPERATING INSTRUCTIONS This KOBE hood is equipped with four electronic controls with a 10 second standby startup amp 30 second delay shutoff two powerful centrifugal turbine impellers with charcoal filter set and two bright 12 vol
13. nce with all applicable codes and standards including fire rated construction 2 When cutting or drilling into wall or ceiling be careful not to damage electrical wiring or other hidden utilities 3 Before servicing or cleaning unit SWITCH POWER OFF AT SERVICE PANEL 4 Clean fan filter if any and grease laden surfaces frequently NOTE This warranty is invalid without an authorized agent s receipt or if unit is damaged due to misuse poor installation improper use mistreatment negligence or any other circumstances beyond the control of KOBE RANGE HOODS authorized agents Any repair carried out without the supervision of KOBE RANGE HOODS authorized agents will automatically void the warranty KOBE RANGE HOODS will not be held responsible for any damages to personal property or real estate or any bodily injuries whether caused directly or indirectly by the range hood WARNING TO REDUCE THE RISK OF PERSONAL INJURY IN THE EVENT OF A RANGE TOP GREASE FIRE Keep fan filter if any and grease laden surfaces clean e Always turn hood ON when cooking at high heat e Use high settings on cooking range ONLY when necessary Heat the oil slowly on low to medium setting Do not leave cooking range unattended when cooking Always use cookware and utensils appropriate for the type and amount of food prepared Use this unit only in the manner intended by the manufacturer Before servicing switch power off at service panel a
14. nches FOR UNDER THE CABINET TABLE 1 Height of Floor to Ceiling Height of Floor to Counter Top Standard 36 C Preferred Height of Counter Top to Hood Bottom Recommended 27 to 30 D Height of Hood E Height of the Cabinet TABLE 2 A Height of Floor to Ceiling B Height of Floor to Counter Top Standard 36 C Preferred Height of Counter Top to Hood Bottom Recommended 27 to 30 D Height of Hood Height of Duct Cover F D F Height of the Hood Installation A UNDER THE CABINET INSTALLATION SAFETY WARNING HOOD MAY HAVE VERY SHARP EDGES PLEASE WEAR PROTECTIVE GLOVES IF IT IS NECESSARY TO REMOVE ANY PARTS FOR INSTALLING CLEANING OR SERVICING Preparation before Installation Temporarily wire the hood to test for proper operation before installing Peel protective film off the hood if any For installing under the cabinet with recessed bottom attach 4 inch wide wood filler strips not included on each side Refer to Figure 1 Measure and create access opening for electrical wires under the cabinet Hood Installation CAUTION If required to move the cooking range to install the hood turn off the power on an electric range at the main electrical box SHUT OFF THE GAS BEFORE MOVING A GAS RANGE 1 Puncture the knockout holes Refer to Figure 2 Figure 1 Figure 2 2 Unscrew the six screws on the bottom casing Remove
15. nd lock service panel if possible to prevent power from switching on accidentally e Clean ventilating fans frequently Grease should not be allowed to accumulate fan filter and oil containers What to Do In The Event Of a Range Grease Fire SMOTHER FLAMES with a close fitting lid cookie sheet or metal tray and then turn off the burner KEEP FLAMMABLE OR COMBUSTIBLE MATERIAL AWAY FROM FLAMES If the flames do not go out immediately EVACUATE THE AREA AND CALL THE FIRE DEPARTMENT 911 NEVER PICK UP A BURNING You may get burned DO NOT USE WATER including wet dishcloths or towels a violent steam blast will result Use an extinguisher ONLY if a You have a Class A B C extinguisher and know how to operate it b The fire is small and contained in the area where it started c The fire department has been called d You can fight the fire with your back to an exit What to Do If You Smell Gas Extinguish any open flame Do not try to turn on lights or any type of appliance Open all doors and windows to disperse the gas If you still smell gas call the Gas Company and Fire department right away CAUTION 1 For general ventilation use only Do not use to exhaust hazardous or explosive materials and vapors 2 To reduce the risk of fire use only metal ductwork 3 Follow the heating equipment manufacturer s guideline and safety standards such as those published by the Nation
16. s regularly To Clean Hood Surface CAUTION NEVER USE ABRASIVE CLEANERS PADS OR CLOTHS Regular care will help preserve its fine appearance 1 2 3 4 5 6 Use only mild soap or detergent solutions Dry surfaces using soft cloth If hood looks splotchy stainless steel hood use an orange base cleaner to clean the surface of the hood Avoid getting cleaning solution on the control switches Only spread a light coating over the surface of the hood and leave on for a few minutes do not leave on too long or this may cause damage to hood finish Use soft towel to wipe off the cleaning solution gently rub off any stubborn spots Use a slightly damp towel to get rid of any cleaning solution Use dry soft towel to dry the hood To bring the glow back into a stainless steel finish use a stainless steel cleaner DO NOT allow deposits to remain for long periods of time DO NOT use ordinary steel wool or steel brushes Small bits of steel may adhere to the surface and cause rust DO NOT allow salt solutions disinfectants bleaches or cleaning compounds to remain in contact with stainless steel for extended periods Many of these compounds contain chemicals which may be harmful Rinse with water after exposure and dry with a clean cloth To Clean Charcoal Filter Set and Oil Containers CAUTION DRAIN OIL CONTAINER BEFORE OIL CAN OVERFLOW 1 Cleaning Charcoal Filter Set Remove the safety screen screw and slide the
17. t 20 watt halogen lights The four button controls are Light Control Speed Control A cycles through Low Medium High QuietMode Speed Control cycles through Low QuietMode High Medium and the Power Control On Off Refer to Figure 12 Figure 12 Light Control Power Control Speed Control Speed Control B Cycles through Low Medium High QuietMode Cycles through Low QuietMode High Medium Turn On Press Power Control On Off button once If any Control button is not pressed within 10 seconds power will be automatically turned off The KOBE hood will start on Low speed Each press of the Speed Control button will cycle through the various speeds Press Speed Control A button to cycle from Low Medium High or QuietMode Press Speed Control B button to cycle from Low QuietMode High or Medium Press Light Control button to turn halogen light on Turn Off Press Power Control On Off button once panel lights will flash and power will be completely shut off after 30 seconds OR Press Power Control On Off button twice all power will be shut off immediately If only the lights are on pressing Power Control On Off button once will turn power off after 30 seconds 10 MAINTENANCE CAUTION NEVER PUT YOUR HAND INTO THE AREA HOUSING THE FAN WHILE THE FAN IS OPERATING For the optimal level of operation clean the range hood surface charcoal filter unit and oil container
18. the bottom casing as shown in Figure If necessary arrange the electrical wire to run through the 1 diameter hole the hood 3 Use calculation on Table 1 and measurements on page 14 as references Center the hood in place beneath the cabinet and flush with the front of the cabinet Refer to Figure 4 Figure 4 4 Draw electrical wires through cabinet access opening 5 Place screws not provided into the exact center of each knockout hole Make sure all screws are in place before tightening screws CAUTION MAKE SURE THE HOOD IS SECURE BEFORE RELEASING 6 Connect the electrical wires Refer to Wiring to Power Supply If necessary to hide the electrical wire connections push wires back into the wiring box Access the wire connections underneath the hood by removing the bottom casing from the six screws Before reattaching the bottom casing make sure wires do not slip between motors impellers or any moving parts to prevent any damage NOTE Be careful when using electrical screwdriver damage to the hood may occur Wiring to Power Supply SAFETY WARNING RISK OF ELECTRICAL SHOCK THIS RANGE HOOD MUST BE PROPERLY GROUNDED MAKE SURE THIS IS DONE BY SPECIALIZED ELECTRICIAN IN ACCORDANCE WITH ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL CODES BEFORE CONNECTING WIRES SWITCH POWER OFF AT SERVICE PANEL AND LOCK SERVICE PANEL TO PREVENT POWER FROM BEING SWITCHED ON ACCIDENTALLY Connect three wires black white and
19. tion or failure to follow the operating instructions ii Connected to improper inadequate or faulty electricity service or exhaust ducts flues or operated using incorrect or contaminated lubricants iii installed maintained or operated otherwise than in accordance with the instructions furnished by KOBE Range Hoods including the improper use of detergents bleaches or cleaners g for damage to range hood during transit delivery installation or removal h for damage by or resulting from attempted repairs conducted by anyone other than our Authorized Service Agent 19 3 The purchaser shall be responsible for any expenses involved in making range hood readily accessible for servicing and where the range hood is installed outside the main sales territory of the retailer or service territory of the nearest approved KOBE Range Hoods Agent as applicable for any traveling expenses and any costs of transporting the range hood or parts thereof to and from the dealer or Service Agent 4 The purchaser must produce proof of purchase together with this warranty certificate when making the claim 5 Damages caused during shipment are not covered under our warranty CONSEQUENTIAL DAMAGE The warrantor is not responsible for any consequential damage SOME STATES DO NOT ALLOW THE EXCLUSION OF CONSEQUENTIAL DAMAGE SO THE ABOVE EXCLUSION MAY NOT APPLY TO YOU IMPLIED WARRANTIES STATE LAW Any implied warranties including the implied w
Download Pdf Manuals
Related Search