Kobe Range Hoods IS2436GSB User's Manual
Contents
1. INSTALLATION PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING Calculation before Installation To calculate installation please refer to TABLE 1 All calculation in inches TABLE 1 A Height of Floor to Ceiling B Height of Floor to Counter Top Standard 36 C Preferred Height of Counter Top to Hood Bottom Recommended 30 to 36 D Height of Hood E Height of the Hood Installation A B C F Height of Duct Cover E D 36 STD A sAFETY WARNING HOOD MAY HAVE VERY SHARP EDGES PLEASE WEAR PROTECTIVE GLOVES IF IT IS NECESSARY TO REMOVE ANY PARTS FOR INSTALLING CLEANING OR SERVICING NOTE BE CAREFUL WHEN USING ELECTRICAL SCREWDRIVER DAMAGE TO THE HOOD MAY OCCUR Preparation before Installation Figure 1 NOTE TO AVOID DAMAGE TO YOUR HOOD PREVENT DEBRIS FROM ENTERING THE VENT OPENING e Decide the location of the venting pipe from the hood to the outside Figure 1 e straight short vent run will allow the hood to perform more efficiently e Try to avoid as many transitions elbows and long run as possible This may reduce the performance of the Nood e Temporarily wire the hood to test for Figure 2 proper operation before installing Refer to figure 5 on page 6 e important Peel protective film off MOUNTING the hood and duct covers if any ON e Use duct tape to seal the joints between pipe sections Advance Planning 12. SIZE COLOR 18 Gauge Commercial Grade Stainless Steel CONSUMPTION AMPERE 240W 2 0A VOLTAGE 120V 60Hz NUMBER OF MOTORS 1 DESIGN 18 Gauge Seamless Satin Finish FANTYPE oquirrel Cage EXHAUST Top 7 Round Damper CONTROLS Touch Screen Multi Function LCD HALOGEN LIGHTS OPTIONAL ACCESSORIES 12V 20W x2 Recirculating Kit Item No RD 0124 SOLD SEPARTELY Net Gross WEIGHT Ibs IS2436GSB 40 51 IS2442GSB 46 58 IS124DC 55 73 SPEED QuietMode Low Medium High Air Capacity cfm 300 480 540 600 Sone 1 0 2 8 4 5 4 8 Specifications subject to change vvithout notice Ceiling measurement is calculated with 30 minimum clearance height and 36 maximum clearance height In House Test Static Pressure 0 13 MEASUREMENTS 8 DIAGRAMS 4 All measurements are in millimeter All inch measurements are converted from millimeter Inch measurements are estimated Mounting Template 12 1 8 308 6 5 16 160 1 eo XE q gt r T 1 ui nc T wo DE CN r c e S gt oo i 2 25 b rly ni I i 6 5 16 160 12 1 8 308 45 127 i Front of Hood Mounting Template Sold Separately IS124DC W RD 0124 Recirculating 51240 Inner Duct Inner Duct Cover Telescopic Cover Telescopic Stack Stack Outer Duct Outer Duct Cover Blower Cover B
3. Damages caused during shipment are not covered under our warranty 19 CONSEQUENTIAL DAMAGE The vvarrantor is not responsible for any consequential damage UNLESS YOU LEAVE IN A STATE THAT DO NOT ALLOW THE EXCLUSION OF CONSEQUENTIAL IMPLIED WARRANTIES STATE LAW Any implied warranties including the implied warranty of merchantability and fitness for purpose imposed on the sale by the laws of the state of sale are limited to two year from the date of original purchase Some states do not allow limitations on the duration of implied warranties This warranty gives you specific legal rights which vary from state to state SERVICE For service please contact KOBE Range Hoods Inc 10505 Valley Suite 302 El Monte CA 91731 U S A Tel 626 350 1355 Fax 626 350 1976 Email customer service koberangehoods com www KOBERangeHoods com 20 PRODUCT REGISTRATION Register Your Producti Any covered failure occurring within two years of original purchase arising from defective workmanship or material in manufacture will be repaired or at our option replaced free of charge by an authorized KOBE Range Hoods Agent or Range Hoods as applicable Keep of purchase original invoice handy for inspection If the range hood is sold by the original purchaser during the warranty period the new owner is protected until the expiration of the original purchasers warranty See warranty section for complete warranty co
4. power from switching on accidentally Clean ventilating fans frequently Grease should not be allowed to accumulate on fan and baffles filters oil containers VVhat to Do In The Event Of a Range Top Grease Fire e SMOTHER FLAMES with a close fitting lid cookie sheet or metal tray and then turn off the burner KEEP FLAMMABLE OR COMBUSTIBLE MATERIAL AWAY FROM FLAMES If the flames do not go out immediately EVACUATE THE AREA AND CALL THE FIRE DEPARTMENT or 911 e NEVER PICK UP A BURNING PAN You Get Burned DO NOT USE WATER including wet dishcloths or towels a violent steam blast will result e Use extinguisher ONLY if a You have a Class extinguisher and know how to operate it 0 The fire is small and contained in the area where it started The fire department has been called d You can fight the fire with your back to an exit What to Do If You Smell Gas e Extinguish any open e Donottry to turn on lights or any type of appliance e Open all doors and windows to disperse the gas If you still smell gas call the Gas Company and Fire Department right away caution 1 For general ventilation use only Do not use to exhaust hazardous or explosive materials and vapors 2 To reduce the risk of fire use only metal ductwork Sufficient air is needed for proper combustion and exhausting of gases through the flue chimney to prevent back drafting 3 Follow the heating equipmen
5. unit and ask assistant to hold steady until step 15 is completed 13 Attach glass canopy with LCD screen underneath the blower unit Make sure blower unit is inside the housing connector Refer to the PARTS LIST on pages 16 17 14 Secure the housing connector to the blower unit with eight M5 x 15 screws provided as shown in Figure 8 15 Ask assistant to slide outer duct cover downward so it rest within the grooves of the glass canopy Figure 8 Connection to LCD Screen sAFETY WARNING RISK OF ELECTRICAL SHOCK THIS RANGE HOOD MUST BE PROPERLY GROUNDED MAKE SURE THIS IS DONE BY QUALIFIED ELECTRICIAN IN ACCORDANCE WITH ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL CODES BEFORE CONNECTING WIRES SWITCH POWER OFF AT SERVICE PANEL AND LOCK SERVICE PANEL TO PREVENT POWER FROM BEING SWITCHED ON ACCIDENTALLY 16 Remove front baffle filter directly behind LCD screen When facing the LCD screen turn knobs slightly to left to release baffle fiter CAUTION DO NOT OVERTURN KNOBS 17 Connect the wires according to connector color to the blower unit 18 Place baffle filters back in place Final Assembly 19 Turn power ON in control panel Check all lights and fan operation 20 Make sure to leave this manual for the homeowner OPERATION INSTRUCTIONS Figure 9 LCD DISPLAY TIME SPEED DATE TIMER DELAY INDICATION INDICATION INDICATION INDICATION INDICATION KOBE LOGO KOBE E E rn
6. KOBE KOBE Brand Range Hood Model No IS2436GSB IS2442GSB 15 124 SERIES ISLAND GLASS CANOPY WITH LCD SCREEN S INSTALLATION INSTRUCTIONS AND OPERATION MANUAL READ AND SAVE THESE INSTRUCTIONS CONTENTS Importan E Sale IM SUUCUON Sa der assis E lalla lalla 1 Components 0 ACK AC C saum aos ee ke DTD et 3 STAN A O esco 4 Operation IASTUCUONS sala 8 h dd Pd da GIA es 11 DPCCIICATIONS m GA didi rias D o o Set 13 Measurements amp Diagrams neve eee eren ete netet ete netet ete netet ete tete teres ete te tete tete veseve se nans 14 IS 16 18 19 Wanani aj III T TIT 20 zizi 22 C READ ALL INSTRUCTIONS CAREFULLY BEFORE STARTING ALL WIRING MUST BE DONE BY A PROFESSIONAL AND IN ACCORDANCE WITH NATIONAL AND LOCAL ELECTRICAL CODES qi US 221947 IMPORTANT SAFETY INSTRUCTIONS PLEASE READ THIS SECTION CAREFULLY BEFORE INSTALLATION WARNING TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK OR PERSONAL INJURY OBSERVE THE FOLLOWING 1 Installation and electrical wiring must be done by qualified professionals and in accordance with all applicable codes and standards including fire rated construction 2 When cutting or drilling into wall or ceiling be careful not to damage electrical wiring or other hidden utilities 3 Ducted fans must be vented to the outside a Before servicing or cleaning u
7. SUPPORT YOUR CLAIM Upon acceptance of items owner assumes responsibility for its safe arrival Report damages to the carrier and file a claim immediately Failure to do so may result in the denial of your claim The carrier will furnish you with necessary forms for filing a claim DAMAGES CAUSED DURING TRANSIT ARE NOT COVERED UNDER OUR WARRANTY 2 PLEASE INSPECT CONTENTS OF PACKAGE S CAREFULLY UPON RECEIPT We must be notified in writing of any damages and or missing parts within the allocated days upon your receipt of package s Contact your local dealer or distributor or call KOBE for the time limit CLAIMS WILL NOT BE ACCEPTED AFTER THE ALLOCATED DAYS NOTE ITEMS WERE THOROUGHLY TESTED AND CAREFULLY PACKED IN OUR FACTORY BEFORE SHIPPING 3 Products must be returned in good working condition with ALL original paris and documentation packed in ALL original cartons fillers and shipping cartons restocking fee of 25 will be charged for all approved items EXCHANGES OR RETURNS MAY BE ACCEPTED IF ANY PACKAGING IS MISSING 4 MAKE SURE TO INSPECT THE HOOD FOR DAMAGES AND DEFECTS BEFORE INSTALLATION Appearance flaws of the hood found after installation and not affecting hood performance is not covered under our warranty for returns or exchanges Service visits not covered under warranty will carry a service charge A Before Installation Return for exchange or refund please see above for acceptable returns B Afte
8. Supply A sAFETY WARNING Figure 5 RISK OF ELECTRICAL SHOCK THIS RANGE HOOD MUST BE PROPERLY GROUNDED MAKE SURE THIS IS DONE BY QUALIFIED ELECTRICIAN IN ACCORDANCE WITH ALL APPLICABLE WIRE NATIONAL AND LOCAL ELECTRICAL CONNECTOR CODES BEFORE CONNECTING WIRES SWITCH POWER OFF AT SERVICE PANEL AND LOCK SERVICE PANEL PREVENT POWER FROM BEING SWITCHED ON ACCIDENTALLY 8 Route house wiring into the ceiling as close to the installation location as possible Allow additional length to drop down from the ceiling to the electric box 9 Conneci the electrical wires according to color green to green white to white and Figure 6 green to green and cap with wire connectors as shown in Figure 5 Green wire must be grounded to reduce risk oi electric shock 7 DUCT PIPE LE ll DUCT TAPE Ductwork Installation T ROUND DAMPER mi 10 Use 7 round aluminum or steel pipe not provided to connect the 7 round damper on the hood to the duciwork above NOTE Place 7 round duct pipe over the damper Seal with duct tape to make all joints secure and air tight NOTE MAKE SURE FLAPS ON DAMPER CAN OPEN 8 CLOSE FREELY Figure 6 Duct Cover Installation 11 Slide the inner duct cover up and secure to Figure the telescopic stack with four ST 3 x 15 screws provided Refer to Figure 7 12 With assistance slide the outer duct cover to the blower
9. centerlines of cook top or range ceiling Use centerlines marked on ceiling to position the mounting template as shown in Figure 2 2 Remove and save template and remove ceiling drywall Install 2 x 4 cross framing lumber not provided between ceiling joists 3 The framing should be spaced 12 1 8 at the Figure 3 front centerline and 14 1 4 on the sides to accept the mounting screw in the telescopic stack Refer to MEASUREMENTS 8 DIAGRAMS pages 14 15 Shown in Figure 3 4 Finish the ceiling surface Be sure to mark the location of the ceiling joists and cross framing lumber 5 Align the mounting template to the ceiling marks and tape in place Cut the 7 1 4 FRONT OF HOOD duct open and approximately 1 wire access hole Drill holes for the 8 mounting screws as indicated on the template TELESCOPIC STACK CEILING JOISTS Telescopic Stack Installation Figure 4 6 Align the telescopic stack to the pre drill holes on the ceiling and securely fasten to the joists and cross framing lumber with eight screws not provided Make sure screws are driven into center of joists and TELESCOPIC cross framing lumber for maximum support Pipe 7 Adjust the blower unit to the telescopic stack using reference calculated in TABLE 1 on page 4 and measurements on pages 14 15 Tighten blower unit to the telescopic stack with four M5 x 15 screws provided as shown in Figure 4 ii a Wiring to Power
10. ll indicate when baffle filter needs cleaning 2 Remove to clean the baffle filter When facing the hood turn knobs slightly to left to release CAUTION DO NOT OVERTURN KNOBS To purchase replacement please contact your local KOBE dealer or call 626 350 1355 Cleaning Baffle Filter 1 Remove all the baffle filters by turning the baffle filter knob slightly to left to release CAUTION DO NOT OVERTURN KNOBS 2 Wash with warm soapy water Dry completely before returning into place Note Baffle Filters are top rack dishwasher safe 11 Replace Light Bulb CAUTION LIGHT UNIT MAY BE HOTI VVAIT UNTIL UNIT IS COOL HALOGEN LIGHT FLAT HEADED BULB 12v 20W 4 CREWDRIVER 1 sure all controls are OFF and range hood is unplugged 2 Place the flat head screwdriver into the groove between the halogen light glass covering and the housing O 3 Gently separate glass covering from the housing 4 Gently pull out the defective light bulb G and discard Light bulbs should be 12V 20W maximum 5 Wear a glove or use a cloth to hold the new light bulb and push securely into light socket NOTE DO NOT PUSH TOO HARD OR YOU MAY BREAK THE BULB CONNECTOR 6 Put back halogen light glass cover 9 7 Plug back power cord and turn on range hood to test for operation 12 SPECIFICATIONS BOX 1 OF 2 IS2436GSB 36 MODEL SIZE IS2442GSB 42 BOX 2 OF2 I8124DC Duct cover with blower unit MODEL
11. lower Unit Unit Dimension 29 1 4 MIN Dimension 26 1 2 MIN 42 1 4 MAX 42 1 4 MAX 14 PARTS LIST MODEL NO IS2436GSB IS2442GSB Box 1 of 2 MODEL NO IS2436GSB NO DESCRIPTION MODEL PART NO Glass Canopy IS2436GSB I Housing Connectr Housing Connector Sensor Control 0003 0004 Baffle Filter 0124 PH 0007 01 Box 2 of 2 PH 0003 02 PH 0004 01 01 02 03 04 05 07 MODEL 151240 NO DESCRIPTION MODEL PART NO a 0003 03 0003 07 PD 0003 12 10 11 12 13 14 19 16 17 18 19 20 21 22 23 24 25 26 21 RECIRCULATING KIT NO RD 0124 OPTIONAL NO DESCRIPTION MODEL PART NO 28 29 30 31 Box Bracket ST3X10 ST3X10 7 Round Adapter Grease Filter 32 RD 0005 01 33 RD 0007 01 O x 15 MODEL NO IS2436GSB IS2442GSB BOX 1 OF 2 GLASS CANOPY WITH LCD SCREEN BOX 2 OF 2 DUCT COVER RECIRCULATING KIT ITEM NO RD 0124 OPTIONAL 16 CIRCUIT DIAGRAM MODEL NO IS2436GSB IS2442GSB YELLOW 16uF 250V qavog 5 20 O 0 QD O JJ 17 DISCLAIMER 1 CAREFULLY INSPECT ALL ITEMS FOR DAMAGES BEFORE ACCEPTING DELIVERY NOTE ANY DAMAGES ON THE FREIGHT BILL OR EXPRESS RECEIPT REQUEST NAME AND SIGNATURE OF THE CARRIER S AGENT AND KEEP COPY TO
12. n on 3 minute delay shutoff OR Press twice will immediately turn fan OFF e Turning ISC Integrated Sensor Control ON OFF 1 Press to turn ISC ON Pec will indicate that the ISC system is ON When gas smoke or higher than normal room temperature is detected fan will automatically turn ON Fan will turn to its highest speed and decrease speed until all gas and smoke are eliminated 2 Press to turn ISC OFF e Turning Lights ON Light control is separate from ON OFF control Turning power off will not turn lights off 1 Press to turn halogen lights ON Each press of will cycle the light intensity through low high and off e Setting Delay Mode Delay Mode will only turn off the fans Other functions that are active will not be turned off 1 Press until ULL icon flashes 2 Press or to set up the time for delay shut down by mm ss 3 Press J until none of the icons are flashing Press to start delay shutdown 4 When countdown reaches 00 00 a warning sound will be emitted and fans will turn off e Setting Timer Mode TIMER 1 Press until Li icon flashes 2 Press or to set the desire time in the timer mode by mm ss 3 Press J until none of the icons are flashing to begin timer When countdown reaches 00 00 a warning sound will be emitted 10 MAINTENANCE A sAFETY WARNING NEVER PUT YOUR HAND INTO AREA HOUSING THE FAN WHILE THE FAN IS OPERATING For the optimal level of operation clea
13. n the range hood surface and baffles filters oil containers regularly To Clean Hood Surface CAUTION NEVER USE ABRASIVE CLEANERS PADS OR CLOTHS Regular care will help preserve the appearance of the hood 1 Use only mild soap or detergent solutions Dry surfaces using soft cloth 2 f hood looks splotchy stainless steel hood use a stainless steel cleaner to clean the surface of the hood Avoid getting cleaner on the control panel Only spread a light coating over the surface of the hood and leave on for a few minutes do not leave on too long or this may cause damage to hood finish Use soft towel to wipe off the cleaning solution gently rub any stubborn spots Use a slightly damp towel to get rid of any cleaning solution Use dry soft towel to dry the hood To bring the glow back into a stainless steel finish use a stainless steel cleaner DO NOT allow deposits to remain for long periods of time DO NOT use ordinary steel wool or steel brushes Small bits of steel may adhere to the surface causing rust 6 DO NOT allow salt solutions disinfectants bleaches or cleaning compounds to remain in contact with stainless steel for extended periods Many of these compounds contain chemicals which may be harmful Rinse with water after exposure and wipe dry with a clean cloth or epo To Clean or Replace Baffle Filter CAUTION DRAIN OIL FROM BAFFLE FILTERS BEFORE OIL CAN OVERFLOW Cleaning Indication 1 The LCD display wi
14. nit open the light panel and SWITCH POWER OFF AT SERVICE PANEL b Clean fan baffles filters oil containers and grease laden surfaces frequently To reduce the risk of fire and to disperse air properly make sure to vent air outside DO NOT vent exhaust air into wall spaces attics crawl spaces or garages NOTE This warranty is invalid without an authorized agent s receipt or if unit is damaged due to misuse poor installation improper use mistreatment negligence or any other circumstances beyond the control of KOBE RANGE HOODS authorized agents Any repair carried out without the supervision of KOBE RANGE HOODS authorized agents will automatically void the warranty KOBE RANGE HOODS will not be held responsible for any damages to personal property or real estate or any bodily injuries whether caused directly or indirectly by the range hood WARNING TO REDUCE THE RISK OF PERSONAL INJURY IN THE EVENT OF RANGE TOP GREASE FIRE Keep fan baffles filters oil containers if any and grease laden surfaces clean Always turn hood ON when cooking at high heat Use high settings on cooking range ONLY when necessary not leave cooking range unattended when cooking Always use cookware and utensils appropriate for the type and amount of food prepared Use this unit only in the manner intended by the manufacturer Before servicing switch power off at service panel and lock service panel if possible to prevent
15. or SOUND INDICATION 2 SELECTION CONTROL gt SELECTION CONTROL COLOR INDICATION e MENU CONTROL INTEGRATED ISC SENSOR CONTROL 4 a 2 O 3 i A LIGHT CONTROL AUTO CONTROL CANCEL SPEED CONTROL BAFFLE POWER DELAY SHUT DOWN CHANGE INDICATION ON OFF PRESS TO TURN ON OFF THE LCD SCREEN When power is turned on LCD screen will light up amp remain lit until turn off When power is turned off LCD screen will remain lit for several seconds before turning off GENERAL SETUP During menu option if a function is not chosen within 10 seconds the icon will stop flashing amp menu option will end e Setting Time 1 PressL until time icon flashes 2 Press GJ or to select current time 2 hh mm E Choose 1 1 e Setting Date 1 Press until date section flashes 2 Press m Or E to select current date e Setting Background Color Bl fe 1 Press until flashes 2 Press or to select background color purple light blue or green e Setting Sound 1 until d flashes 2 Press to select sound OR Press to mute sound When 4 appears keypad sound is ON HOOD OPERATION e Turning Fan ON OFF 1 Press to turn fan ON Each press of Will cycle the fan through QuietMode Low Medium and High The screen will indicate MT QuietMode Speed L Low Speed I Medium Speed ul _ High Speed 2 Press once will place fa
16. r Installation NO exchange or refund 18 VVARRANTY VVARRANTY CERTIFICATE KOBE Range Hoods Inc warrants all products manufactured or supplied by it to be defects in vvorkmanship and materials obligations pursuant to this warranty are limited to a period of two years from the date of purchase and to the repair or replacement at its option and subject to the terms and conditions stated below of any component which its examination shall disclose to be so defective TWO YEAR WARRANTY SERVICE PERIOD Any warranted failure occurring within two years of original purchase arising from defective vvorkmanship or material in manufacture will be repaired or replaced at our own discretion free of charge by an authorized KOBE Range Hoods agent or KOBE Range Hoods as applicable Keep of purchase or original invoice handy for inspection If the range hood is sold by the original purchaser during the warranty period the new owner is protected until the expiration of the original purchaser s warranty CONDITIONS The following conditions apply only in relation to the warranty expressly given in this certificate 1 This warranty applies only a within U S A and Canada b to range hoods used for PRIVATE SINGLE FAMILY USE if used for COMMERCIAL or MULTIPLE FAMILY USE or other purposes warranty will be voided 2 Repair of any fault to be provided under this warranty shall not be provided a the identification n
17. t manufacturer s guideline and safety standards such as those published by the National Fire Protection Association NFPA and the American Society for Heating Refrigeration and Air Conditioning Engineers ASHRAE and code authorities 4 Activating any switch on may cause ignition or an explosion 5 Due to the size and weight of this hood two people installation is recommended WARNING ELECTRICAL SHOCK HAZARD Can result in serious injury or death Disconnect appliance from electric power before servicing equipped the fluorescent light bulb contains small amounts mercury which must be recycled or disposed of according to Local State and Federal Codes COMPONENTS OF PACKAGE Must keep all material for returns or refunds BOX 1 OF 2 MODEL NO 152436GSB MODEL NO 192442GSB O Glass Canopy w LCD Screen 1 O Baffle Filter 2 O VVarranty Registration Card 1 Instructions Manual 1 Attached to Hood BOX 2 OF 2 MODEL 15124DC KOBE KOBE Brand Range Hood Model 152436658 O Telescopic Stack 1 O Blovver Unit 1 Inner Duct Cover 1 Outer Duct Cover 1 Mounting Template 1 7 Round Damper 1 D Screws Package 5 M 5 x 15 12 pcs ST 3x15 4 pcs Attached to the Unit 4 OPTIONAL RECIRCULATING KIT AVAILABLE FOR MORE INFORMATION PLEASE VISIT OUR WEBSITE WWW KOBERANGEHOODS COM OR CONTACT KOBE RANGE HOODS 626 350 1355
18. umber attached to the range hood has been removed altered or rendered illegible notice of the defect has not been given within the period applicable C for failure of light bulbs d for physical damage e for surfaces damaged by use of improper chemical cleaning agents f ifthe appliance has been i subject to misuse abuse negligence accident incorrect installation or failure to follow the operating instructions li connected to improper inadequate or faulty electricity service or exhaust ducts or duct cover or operated using incorrect or contaminated lubricants installed maintained or operated not in accordance with the instructions furnished by KOBE Range Hoods including the improper use of detergents bleaches or cleaners g for damage to range hood during transit delivery installation or removal h for damage by or resulting from attempted repairs conducted by anyone other than KOBE Authorized Service Agent 3 The purchaser shall be responsible for any expenses involved in making the range hood readily accessible for servicing and service to range hood installed outside the main sales territory of the retailer or service territory of the nearest approved KOBE Range Hoods Agent as applicable for any traveling expenses and costs of transporting the range hood or parts thereof to and from the dealer or Service Agent 4 The purchaser must produce proof of purchase and this warranty certificate when making the claim 5
19. verage information This appliance has been manufactured tested and inspected to the standards required by KOBE Range Hoods PLEASE MAIL IN YOUR WARRANTY REGISTRATION CARD AND PROOF OF PURCHASE TO Range Hoods Inc 10505 Valley Blvd Suite 302 Monte CA 91731 RECORD THE FOLLOWING INFORMATION FOR YOUR RECORD Model No Serial No Purchased Date Purchased From IMPORTANT PLEASE A COPY OF YOUR SALE RECEIPT OR INVOICE HANDY WHEN REQUESTING FOR SERVICE 21 Range Hoods 10505 Valley Blvd Suite f 302 El Monte CA 91731 USA http www KOBERangeHoods com This KOBE hood is made for use in the USA and CANADA only We do not recommend using this hood overseas as the power supply may not be compatible and may violate the electrical code of that country Using a KOBE hood overseas is at your own risk and will void your warranty V 070717
Download Pdf Manuals
Related Search