Kobe Range Hoods IS2336SQ User's Manual
Contents
1. PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING Calculation before Installations To calculate the length of the installation please refer to Table 1 All calculation is measure in inches TABLE 1 A Height of Floor to Ceiling B Height of Floor to Counter Top Standard 36 C lt Preferred Height of Counter to Hood Bottom Recommended 30 to 36 D Height of Hood E Height of the Hood Installation A 36 STD F Height of Duct Cover E D SAFETY WARNING HOOD MAY HAVE VERY SHARP EDGES PLEASE WEAR PROTECTIVE GLOVES IF IT IS NECESSARY TO REMOVE ANY PARTS FOR INSTALLING CLEANING OR SERVICING Preparations of Ductwork and Location NOTE TO AVOID DAMAGE TO YOUR HOOD PREVENT DEBRIS FROM ENTERING THE VENT OPENING Decide the location of the venting pipe from the hood to the outside Refer to Figure 1 straight short venting run will allow the hood to perform more efficiently Try to avoid as many transitions elbows and long run as possible This may reduce the performance of the hood Use duct tape to seal the joints between pipe sections 6 ROUND PIPE Figure 1 Telescopic Stack Installation Note Duct cover with telescopic stack sold separately 1 2 Mark centerlines of cook top or range on ceiling above Use centerlines marked on ceiling to position the mounting template as shown in Figure 2 Remove and save template Cut and remove ceil2. If only the lights are on pressing Power Control On Off button once will turn power off after 30 seconds MAINTENANCE CAUTION NEVER PUT YOUR HAND INTO THE AREA HOUSING THE FAN WHILE THE FAN IS OPERATING For the optimal level of operation clean the range hood surface filter set and oil containers regularly To Clean Hood Surface CAUTION NEVER USE ABRASIVE CLEANERS PADS OR CLOTHS Regular care will help preserve its fine appearance 1 2 3 4 5 6 Use only mild soap detergent solutions Dry surfaces using soft cloth If hood looks splotchy stainless steel hood use an orange base cleaner to clean the surface of the hood Avoid getting cleaning solution on the control switches Only spread a light coating over the surface of the hood and leave on for a few minutes do not leave on too long or this may cause damage to hood finish Use soft towel to wipe off the cleaning solution gently rub off any stubborn spots Use a slightly damp towel to get rid of any cleaning solution Use dry soft towel to dry the hood To bring the glow back into a stainless steel finish use a stainless steel cleaner DO NOT allow deposits to remain for long periods of time DO NOT use ordinary steel wool or steel brushes Small bits of steel may adhere to the surface and cause rust DO NOT allow salt solutions disinfectants bleaches or cleaning compounds to remain in contact with stainless steel for extended periods
3. C1 0708 0003 31 Transformer Moto 161 0402 0120 40 MODEL NO 1 1230 ORIGINAL KIT Sold Separately KEY NO DESCRIPTION MODEL SIZE PART NO 01 Duct Cover IS123DC 12 04000 304 51 IS123 16DC 12 04016 304 51 15123 590 12 04059 304 51 Round Head Screw 3 16 x 3 8 1 0707 0001 03 Telescopic Stack IS123DC C1 0203 1242 36 04 Round Head Screw 3 16 3 8 1 0708 0001 05 DuctCoverScrew 3x8mm 1 0707 0001 06 Round Head Screw TS4x6 Cf 0001 000 7 FitrSet SBF MF 0201 Safety Screen 1 C1 06020200 A B C Oil Container Round 1 0503 0201 Safety Screen Screw 19159705000 MODEL NO 151230 RECIRCULATING Sold Separately 01 Duct Cover Recirculating Round Head Screw 3 16 x 3 8 1 Cft 070700001 03 Telescopic Stack Round Head Screw 3 16 x 3 8 Cf 0708001 Cft070700001 Duct Cover Screw 3 x 8 mm 06 Round Head Screw TS 4 x 6 1 0101 0001 Charcoal Filter Set RH CFO01 Charcoal Filter 1 0603 0302 Mesh Filter MF 0201 C1 0604 0201 Safety Screen 1 0602 0202 Oil Container Round 1 0503 0201 Safety Screen Screw 1 0705 0001 15 15233650 15234250 MODEL NO DUCT COVER FILTER SET ORIGINAL KIT RECIRCULATING KIT 16 CIRCUIT DIAGRAM MODEL NO 15233650 15234250 3 543 5 250VAC ERR T Y
4. published by the National Fire Protection Association NFPA and the American Society for Heating Refrigeration and Air Conditioning Engineers ASHRAE and code authorities 4 Activating any switch may cause ignition or an explosion WARNING ELECTRICAL SHOCK HAZARD Can result in serious injury or death Disconnect appliance from electric power before servicing If equipped the fluorescent light bulb contains small amounts of mercury which must be recycled or disposed of according to Local State and Federal Codes COMPONENTS OF PACKAGE Must Keep all material for returns or refunds BOX 1 A KOBE Range Hood Mounting Template C Warranty Registration Card D Instructions Manual ORIGINAL KIT G BOX 2 SOLD SEPARATELY Inner Duct Cover 3 16 x 3 8 mm 8 pcs E Telescopic Stack F Two Piece Duct Cover 4 x 8 mm 16 pcs G Screws Package H Filter Set Model IS123F Mesh Filter x 2 Safety Screen x 2 Oil Container Round x 2 Screw x 2 RECIRCULATING KIT me BOX 2 SOLD SEPARATELY B 3 16 x 3 8 mm 8 pcs E Telescopic Stack lt gt 8 F Two Piece Duct Cover gt Nr G Screws Package prs H Charcoal Filter Set 22 H Model No Charcoal Filter x 2 Mesh Filter x 2 Safety Screen x 2 Oil Container Round x 2 Screw x 2 Outer Duct Cover INSTALLATION
5. 500 150 640 200 720 330 800 400 sone Original Recirculating 1 0 1 0 3 0 3 0 4 5 4 5 4 8 14 8 In House Test Static Pressure 0 One sone is equivalent to the sound of a refrigerator at 40 decibels Specifications subject to change without notice 11 MEASUREMENTS 8 DIAGRAMS All inch measurements are converted from millimeters Inch measurements are estimated Al measurements in are millimeters 9 9 p D ORIGINAL KIT Sold Separately MODEL NO DCH T MAX HT INTSALLED 1 SH H 460 490 950 370 575 946 925 me eo s wa awo 235 210 445 405 405 770 735 1505 650 854 1505 1485 DUCT COVER TELESCOPIC STACK oo Ky SELL eo TES E DCH B Inner duct cover is taller than outer duct cover RECIRCULATING KIT Sold Separately MODEL NO A DCH T MAX HT INTSALLED 1 SH 460 490 950 370 575 946 925 Gu emo eo e awo 235 210 445 405 405 770 735 1505 650 854 1505 1485 DUCT COVER TELESCOPIC STACK Inner duct cover is taller than outer duct cover 13 PARTS LIST MODEL NO 15233650 15234250 1 0406 0120 01 KEY DESCRIPTION MODEL SIZE PART NO 6 Round Plastic Exhaust C1 0505 0001 TT I Round Head Screw TS 4 x 6 1 0708 0006 Hood Roof Po B101 1242
6. 13 15233659 5 Hood Casing IS2336SQ B101 1236 02 IS2342SQ B101 1242 02 6 Transformer Bracket C1 0202 1242 Transformer Light C1 0402 0120 40 Transformer Bracket Screw 3 16 3 8 C1 0707 0001 11 16 Halogen Light 12V 20W Max 1 0403 0101 Transformer Support Light L C1 0201 1242 a 1 0707 0001 C1 0401 0120 01A 1 0707 0001 Screw 3 16 x 3 8 Round Head Screw TS 4 x 6 Processor Board Box C1 0501 0102 C1 0404 0401 B Flat Head Screw M 2 x 8 C1 0704 0003 17 Air Chamber A Air Chamber Top C1 0102 41242 B Air Chamber Side Of 0101 1222 O 18 X C1 0301 0120 07A 19 Motor Right X X 1 0301 0120 08 20 Turbine Impeller Lef O C1 0251 0092 01 21 Turbine Impeller Right Z o C1 0251 0092 02 22 jOlTume 1 0502 0201 23 Bottom Casing 15233650 101 1236 09 15234250 101 1242 09 24 lt Impeller Plastic 10251 00010 25 Motor Position Screw 3 16 x 5 8 C1 0703 0001 26 BottomCasing Screw 3 16 5 8 10704 0000 Transformer Screw 3 16 x 3 8 10707 0001 28 Control Board Cf 0404 0401 A 29 Control Unit Cf 050 0001 J 30 Round Head Screw TS 1 8 x 3 8
7. AKE SURE TO INSPECT THE HOOD FOR DAMAGES AND DEFECTS BEFORE INSTALLATION Appearance flaws of the hood found after installation and not affecting hood performance is not covered under our warranty for returns or exchanges Service visits not covered under warranty will carry a service charge A Before Installation Return for exchange or refund please see above for acceptable returns B After Installation NO exchange or refund 18 WARRANTY CERTIFICATE KOBE Range Hoods Inc warrants all products manufactured or supplied by it to be free from defects in workmanship and materials Its obligations pursuant to this warranty are limited to a period of two years from the date of purchase and to the repair or replacement at its option and subject to the terms and conditions stated below of any component part which its examination shall disclose to be so defective TWO YEAR WARRANTY SERVICE PERIOD Any covered failure occurring within two years of original purchase arising from defective workmanship or material in manufacture will be repaired or at our option the unit will be replaced free of charge by an authorized KOBE Range Hoods Agent or KOBE Range Hoods as applicable Keep proof of purchase or original invoice handy for inspection If the range hood is sold by the original purchaser during the warranty period the new owner is protected until expiration of the original purchaser s warranty CONDITIONS The follo
8. KORBE KOBE Brand Range Hood Model 1S2336SQ IS2342SQ IS 123 SERIES 7 HEIGHT s INSTALLATION INSTRUCTIONS AND OPERATION MANUAL READ AND SAVE THESE INSTRUCTIONS CONTENTS Important Safety INSIMUICUONS 1 Components or PACKAGE ic orans 3 4 Operaundg InstrHellOllS usas RE TAR EEOAE EDA 8 EM 11 Measurements amp nensem nn 12 TER 14 GCU ETUR UU 17 E E o E 18 19 AMOI ec c 21 READ ALL INSTRUCTIONS CAREFULLY BEFORE STARTING ALL WIRING MUST BE DONE BY A PROFESSIONAL AND IN ACCORDANCE WITH NATIONAL AND LOCAL ELECTRICAL CODES O 221547 IMPORTANT SAFETY INSTRUCTIONS PLEASE READ THIS SECTION CAREFULLY BEFORE INSTALLATION WARNING TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK OR PERSONAL INJURY OBSERVE THE FOLLOWING 1 Installation and electrical wiring must be done by qualified professionals and in accordance with all applicable codes and standards including fire rated construction 2 When cutting or drilling into wall or ceiling be careful not to damage electrical wiring or other hidden utiliti
9. Many of these compounds contain chemicals which may be harmful Rinse with water after exposure and dry with a clean cloth To Clean Filter Sets and Oil Containers CAUTION DRAIN OIL CONTAINER BEFORE OIL CAN OVERFLOW 1 2 3 Normal Cleaning Spray a mild degreaser into the fan and turn on high speed Liquid residue will accumulate in the oil containers round Cleaning Oil Containers Remove the oil container by turning counter clockwise Wash with warm soapy water Dry completely before returning into place rack dishwasher safe Cleaning Filter Set or Charcoal Filter Set Remove the safety screen screw and slide the filter set or charcoal filter set out Remove oil container by turning counter clockwise Wash with warm soapy water Dry completely before returning into place rack dishwasher safe To Replace Light Bulb CAUTION HALOGEN LIGHT UNIT MAY BE HOT WAIT UNTIL UNIT IS COOL 1 2 3 4 5 Make sure all control switches are and range hood is unplugged Use a flat head screwdriver to pop out the protective covering as shown in Figure 10 Gently pull out the defective light bulb and discard Light bulb should be 12V 20W maximum Refer to Figure 11 Push bulb securely into light socket Replace protective cover Plug in range hood Figure 10 Figure 11 10 SPECIFICATIONS MODEL SIZE COLOR VOLTAGE NUMBER OF MOTORS DESIGN FAN TYPE E
10. SLLOW M 2 POWER RECE OCLE TD E e GR WHITE ORANGE YELLOW GREEN BLUE WHITE BLUE WHITE BLUE 2 OF dm ad 5 17 DISCLAIMER 1 CAREFULLY INSPECT ALL ITEMS FOR DAMAGES BEFORE ACCEPTING DELIVERY NOTE ANY DAMAGES ON THE FREIGHT BILL OR EXPRESS RECEIPT REQUEST NAME AND SIGNATURE OF THE CARRIER S AGENT AND KEEP COPY TO SUPPORT YOUR CLAIM Upon acceptance of items owner assumes responsibility for its safe arrival Damages should be reported to carrier and a claim filed Failure to do this could result in the carrier refusing to honor your claim The carrier will furnish you with necessary forms for filing a claim DAMAGES CAUSED DURING TRANSIT ARE NOT COVERED UNDER OUR WARRANTY PLEASE INSPECT CONTENTS OF PACKAGE S CAREFULLY UPON RECEIVING We must be notified in writing of any damages and or missing parts within the allocated days upon receipt of package s Contact your local KOBE dealer or distributor or call KOBE for the time limit CLAIMS WILL NOT BE ACCEPTED AFTER THE ALLOCATED DAYS NOTE ITEMS WERE THOROUGHLY TESTED AND CAREFULLY PACKED IN OUR FACTORY Products must be returned in good working condition with ALL original parts and documentation packed in ALL original cartons fillers and shipping cartons A restocking fee of 25 will be charged for all approved return s EXCHANGES OR RETURNS MAY NOT BE ACCEPTED IF ANY PACKAGING IS MISSING M
11. XHAUST CONTROLS HALOGEN LIGHTS HOOD DIMENSION W x D x H TELESCOPIC STACK DIMENSION W x D x H DUCT COVER DIMENSION W x D x H 15233650 36 15234250 42 304 Commercial Grade Stainless Steel 120 60Hz 2 18 Gauge Seamless Twin Turbine Impeller 6 Round Electronic Control 4 Buttons 10 Second Standby Startup 30 Second Delay Shutoff 12V 20W x 4 IS2336SQ 35 3 4 x 27 x 7 IS2342SQ 41 3 4 x 27 x 7 Two Piece Adjustable Telescopic Stack 1 Original Kit Sold Separately 151230 11 1 8 x 9 1 8 x 22 5 8 36 3 8 I8123 16DC 11 1 8 x 9 1 8 x 16 15123 590 11 1 8 x 9 1 8 x 33 5 8 58 1 2 2 Recirculating Kit Sold Separately IS123DCD 11 1 8 x 9 1 8 x 22 5 8 36 3 8 I8123 16DCD 11 1 8 x 9 1 8 x 16 I8123 59DCD 11 1 8 x 9 1 8 x 33 5 8 58 1 2 Two Piece Adjustable Duct Cover 1 Original Kit Sold Separately 151230 11 3 8 x 9 1 2 x 18 1 8 37 3 8 15123 160 11 3 8 x 9 1 2 x 9 1 4 17 1 2 15123 590 11 3 8 x 9 1 2 x 30 1 4 59 1 4 2 Recirculating Kit Sold Separately IS123DCD 11 3 8 x 9 1 2 x 18 1 8 37 3 8 I8123 16DCD 11 3 8 x 9 1 2 x 9 1 4 17 1 2 I8123 59DCD 11 3 8 x 9 1 2 x 30 1 4 59 1 4 15233650 15234250 WEIGHT lbs Hood 53 0 55 0 GROSS WEIGHT lbs Hood 73 0 77 0 SPEED QuietMode Low Medium High Air Capacity cfm Original Recirculating
12. d readily accessible for servicing and where the range hood is installed outside the main sales territory of the retailer or service territory of the nearest approved KOBE Range Hoods Agent as applicable for any traveling expenses and any costs of transporting the range hood or parts thereof to and from the dealer or Service Agent 4 The purchaser must produce proof of purchase together with this warranty certificate when making the claim 5 Damages caused during shipment are not covered under our warranty CONSEQUENTIAL DAMAGE The warrantor is not responsible for any consequential damage SOME STATES DO NOT ALLOW THE EXCLUSION OF CONSEQUENTIAL DAMAGE SO THE ABOVE EXCLUSION MAY NOT APPLY TO YOU IMPLIED WARRANTIES STATE LAW Any implied warranties including the implied warranty of merchantability and fitness for purpose imposed on the sale by the laws of the state of sale are limited to two year from the date of original purchase Some states do not allow limitations on the duration of implied warranties This warranty gives you specific legal rights and may also have rights which vary from state to state SERVICE For service contact KOBE Range Hoods Inc 4934 Walnut Grove Avenue Suite 202 san Gabriel CA 91776 U S A Tel 626 309 1356 Fax 626 309 1366 Email customerservice koberangehoods com www KobeRangeHoods com 20 PRODUCT REGISTRATION Register Your Product Any covered failure occurring within two years o
13. es 3 Ducted fans must be vented to the outside a Before servicing or cleaning unit open the light panel and SWITCH POWER OFF AT SERVICE PANEL b Clean fan optional filter and grease laden surfaces frequently To reduce the risk of fire and to disperse air properly make sure to vent air outside DO NOT vent exhaust air into wall spaces attics crawl spaces or garages NOTE This warranty is invalid without an authorized agent s receipt or if unit is damaged due to misuse poor installation improper use mistreatment negligence or any other circumstances beyond the control of KOBE RANGE HOODS authorized agents Any repair carried out without the supervision of KOBE RANGE HOODS authorized agents will automatically void the warranty KOBE RANGE HOODS will not be held responsible for any damages to personal property or real estate or any bodily injuries whether caused directly or indirectly by the range hood WARNING TO REDUCE THE RISK OF PERSONAL INJURY IN THE EVENT OF A RANGE TOP GREASE FIRE e Keep fan filter if any and grease laden surfaces clean e Always turn hood ON when cooking at high heat Use high settings on cooking range ONLY when necessary Heat the oil slowly on low to medium setting Do not leave cooking range unattended when cooking Always use cookware and utensils appropriate for the type and amount of food prepared Use this unit only in the manner intended by the manufacturer Before servicing s
14. f original purchase arising from defective workmanship or material in manufacture will be repaired or at our option the unit will be replaced free of charge by an authorized KOBE Range Hoods Agent or KOBE Range Hoods as applicable Keep proof of purchase original invoice handy for inspection If the range hood is sold by the original purchaser during the warranty period the new owner is protected until expiration of the original purchaser s warranty See warranty section for complete warranty coverage information This appliance has been manufactured tested and inspected to the standards required by KOBE Range Hoods PLEASE MAIL IN YOUR WARRANTY REGISTRATION CARD AND PROOF OF PURCHASE TO KOBE Range Hoods Inc 4934 Walnut Grove Avenue Suite 202 oan Gabriel CA 91776 RECORD THE FOLLOWING INFORMATION FOR YOUR RECORD Model No Serial No Purchased Date Purchased From IMPORTANT PLEASE KEEP A COPY OF YOUR SALE RECEIPT OR INVOICE HANDY WHEN REQUESTING FOR SERVICE 21
15. ing drywall Install 2 x 4 cross framing lumber not provided between ceiling joists Refer to Figure 3 Consult a professional if you have difficulty or your installation is unique Finish the ceiling surface Be sure to mark the location of the ceiling joists and cross framing or replace the mounting template in the position of the ceiling joists amp cross framing Attach the telescopic stack to the ceiling and securely fasten to the joists and cross framing with eight screws not provided as shown in Figure 3 Make sure screws are driven into center of joists and cross framing for maximum support Adjust the telescopic stack using reference F calculated in Table 1 and measurements on page 12 Tighten from the side with eight 4x8 mm screws provided as shown in Figure MOUNTING TEMPLATE CEILING Figure 3 MEASUREMENT F FROM TABLE 1 Figure 4 Duct Cover Installation 6 Slide the duct cover up and secure the inner duct cover to the telescopic stack with four 4x8 mm screws provided Refer to Figure 5 Hood Installation 8 Place temporary screws to hold the duct cover up Install the hood as shown in Figure 6 Use eight 3 16x3 8 mm screws provided to secure hood to telescopic stack Make sure to tighten screws securely Refer to Figure 6 4X 8 MM SCREWS INNER DUCT COVER OUTER DUCT COVEF 6 ROUND LOWER TELESCOPIC STACK Figure 6 Figure 5 Wiring to Powe
16. o leave this manual for the homeowner WIRING BOX INNER DUCT COVER OUTER DUCT COVER Figure 7 Figure 8 OPERATING INSTRUCTION This KOBE hood is equipped with four electronic controls with a 10 second standby startup amp 30 second delay shutoff two powerful centrifugal turbine impellers and four bright 12 volt 20 watt halogen lights The four control buttons are Light Control Speed Control A cycles through Low Medium High QuietMode Speed Control B cycles through Low QuietMode High Medium and the Power Control On Off Refer to Figure 9 Figure 9 Light Control Power Control Speed Control Speed Control B Cycles through Low Medium High QuietMode Cycles through Low High Medium Turn On Press Power Control On Off button once If any Control button is not pressed within 10 seconds power will be automatically turned off The KOBE hood will start on Low speed Each press of the Speed Control button will cycle through the various speeds Press Speed Control A button to cycle from Low Medium High or QuietMode Press Speed Control B button to cycle from Low QuietMode High or Medium Press Light Control button to turn halogen light on Turn Off Press Power Control On Off button once panel lights will flash and power will be completely shut off after 30 seconds OR Press Power Control On Off button twice all power will be shut off immediately
17. r Supply ASAFETY WARNING RISK OF ELECTRICAL SHOCK THIS RANGE HOOD MUST BE PROPERLY GROUNDED MAKE SURE THIS IS DONE BY SPECIALIZED ELECTRICIAN IN ACCORDANCE WITH ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL CODES BEFORE CONNECTING WIRES SWITCH POWER OFF AT SERVICE PANEL AND LOCK SERVICE PANEL TO PREVENT POWER FROM BEING SWITCHED ON ACCIDENTALLY 9 10 11 12 13 Remove the wiring box cover as shown in Figure 7 Remove the knockout from the wiring Connect three wires black white green to house wires cap with wire connectors Connect according to color Black to black white to white and green to green Close the wiring box cover and make sure that wires are not pinched between cover and box Test the operation of the hood before moving on to next step Make sure power is supplied to the hood Ductwork Installation Note Skip this step if installing recirculating kit 14 Use 6 round pipe to connect the plastic exhaust on the hood to the ductwork above 15 Use duct tape to make all joints secure and air tight Final Assembly 16 Remove the temporary screws and slide the outer duct cover downward so that it sits properly on the hood 17 NOTE Be careful when using electrical screwdriver damage to the hood may occur secure the duct cover to hood with four 4x8 mm screws provided as shown in Figure 8 18 Turn power ON in control panel Check all lights and fan operation 19 Make sure t
18. wing conditions apply only in relation to the warranty expressly given in this certificate 1 This warranty applies only a within U S A and Canada b to range hoods used for PRIVATE SINGLE FAMILY USE if used for COMMERCIAL or MULTIPLE FAMILY USE or other purposes warranty will be voided 2 Repair of any fault to be provided under this warranty shall not be provided a if the identification number attached to the range hood has been altered rendered illegible or removed b if notice of the defect has not been given within the period applicable c for failure of light bulbs d for physical damage e for surfaces damaged by use of improper chemical cleaning agents f if the appliance has been i subject to misuse abuse negligence accident incorrect installation or failure to follow the operating instructions ii connected to improper inadequate or faulty electricity service or exhaust ducts or flues or operated using incorrect or contaminated lubricants iii installed maintained or operated otherwise than in accordance with the instructions furnished by KOBE Range Hoods including the improper use of detergents bleaches or cleaners g for damage to range hood during transit delivery installation or removal h for damage by or resulting from attempted repairs conducted by anyone other than our Authorized Service Agent 19 3 The purchaser shall be responsible for any expenses involved in making the range hoo
19. witch power off at service panel and lock service panel if possible to prevent power from switching on accidentally e Clean ventilating fans frequently Grease should not be allowed to accumulate on fan filter and oil containers What to Do In The Event Of a Range Grease Fire SMOTHER FLAMES with a close fitting lid cookie sheet or metal tray and then turn off the burner KEEP FLAMMABLE OR COMBUSTIBLE MATERIAL AWAY FROM FLAMES If the flames do not go out immediately EVACUATE THE AREA AND CALL THE FIRE DEPARTMENT or 911 NEVER PICK UP A BURNING PAN You may get burned DO NOT USE WATER including wet dishcloths or towels a violent steam blast will result Use an extinguisher ONLY if a You have a Class A B C extinguisher and know how to operate it b The fire is small and contained in the area where it started c The fire department has been called d You can fight the fire with your back to an exit What to Do If You Smell Gas Extinguish any open flame Do not try to turn on the lights or any type of appliance Open all doors and windows to disperse the gas If you still smell gas call the Gas Company and Fire Department right away CAUTION 1 For general ventilation use only Do not use to exhaust hazardous or explosive materials and vapors 2 To reduce the risk of fire use only metal ductwork 3 Follow the heating equipment manufacturer s guideline and safety standards such as those
Download Pdf Manuals
Related Search