Klipsch Stereo System 2.1 User's Manual
Contents
1. imaging with movies and games the two satellite speakers should be positioned on each side the video monitor For music listening the satellite speakers can be placed in any convenient location within 30 feet of the computer with the USB Transmitter For best sound and imaging place the speakers near ear level and 3 5 feet apart To wall mount the pedestal stands may be removed by unscrewing the 1 4 20 thread bolt which accommodates a wide variety of wall brackets available through stereo and appliance stores Klipsch WB 1 wall brackets are available at www klipsch com 3 Place the subwoofer on the floor within the cables reach of the satellite speak ers The subwoofer must be placed on the floor near a wall with the rear panel toward the wall Do not cover up the sub driver or front port of the enclosure and be sure to provide enough ventilation to the rear of the subwoofer It is normal for this panel to be warm to the touch The subwoofer should be at least 3 feet 1m from a CRT monitor to avoid interference Placing the subwoofer in a corner can further enhance bass output Subwoofer placement will ultimately be determined by what sounds best to your ear 4 Speaker or power cables running across an area of heavy foot traffic should be positioned against a wall or corner and secured with tape SPEAKER CONNECTION DIAGRAM 1 Do not plug in the AC power cord until your computer audio system is set up 2 Care should be advised concerni2. limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference n a residential installation This equipment generates uses and can radiate radio frequency energy and if not in stalled and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Approved under the verification provision of FCC Part 15 as a Class B Digital Device Caution Changes or modifications not expressly approved by the manufacturer could void the user s authority to operate this device WIRELESS TRANSMITTER COMPLIANCE INFORMATION This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with minimum distance 20cm be
3. removing the USB transmitter the computer should revert back to the computer s built in sound output device the laptop s built in speaker or headphone output for example It may be necessary to close and restart the music player software for the change to take effect Likewise when plugging in the USB transmitter the Klipsch ProMedia 2 1 Wireless speakers should become the default output device but the music player software may need to be restarted This is not a problem with the Klipsch system it is a limitation of the computer s software and operating system If after restarting the music player DVD player software the music does not play through the ProMedia 2 1 Wireless system check to make sure the LED indica tors are on but not blinking and that the operating system as described above in 4 and 5 has the Klipsch speakers selected as the active audio output device Also check that the computer s volume control is not muted SOFTWARE AND HARDWARE GAIN CONTROLS Software volume controls in Microsoft Windows 1 Click the Start button on your taskbar then All Programs 2 Choose Accessories 3 Windows 95 Choose Multimedia Windows 98 2000 XP Vista Choose Entertainment 4 Click on the Volume Control 5 Adjust the Wave Volume Elevator Button to approximately 70 Alternatively if your computer is not within arms reach of the speakers you may desire to set the volume setting higher on the Control Pod and use the computer s vo
4. Klipsch ProMedia 2 1 Wireless Owner s Manual IMPORTANT SAFETY INFORMATION READ these instructions KEEP these instructions HEED all warnings FOLLOW all instructions DO NOT use this apparatus near water CLEAN ONLY with dry cloth DO NOT block any ventilation openings Install in accordance with the manufacturer s instructions Do not install near any heat sources such as radiators heat registers stoves or other appara us including amplifiers that produce heat DO NOT defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wider blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet 10 PROTECT the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus 11 ONLY USE attachments accessories specified by the manufacturer 12 USE only with a cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avoid injury from tip over 13 UNPLUG this apparatus during lightning storms or when unused for long periods of time 14 REFER all servicing to qualified service pers
5. ent USB port try a different USB port or use the included 4 USB extension cable NOTE Does not work with the USB output on gaming systems d The first time the USB transmitter is plugged in the computer should recognize the new hardware and install the appropriate driver e When plugged in the LED on USB transmitter should begin to flash 3 After several seconds the LEDs on both the subwoofer rear panel and USB transmitter should stop flashing a The LEDs should remain on this indicates that the USB transmitter and subwoofer are now synchronized and audio from the computer is streaming to the ProMedia 2 1 Wireless system b The USB wireless transmitter and subwoofer are paired at the factory however if after 30 seconds the LEDs are still flashing press the SYNC button on the rear of the subwoofer and the button with the chevron on the USB transmitter The system will attempt to sync again 4 If you are running Windows open Control Panel Sounds and Audio Devices Audio tab and check to make sure that Klipsch ProMedia 2 1 Wireless is listed as the default audio playback device 5 If you are running a Mac OS click the Apple icon select System Preferences Sound Output tab and check to make sure the Klipsch ProMedia 2 1 Wireless is selected as the default output device 6 Start the Music Player DVD Player software i e iTunes Windows Media Player etc and play your music as normal NOTE When
6. ibit distortion or buzzing Turn down computer s volume via control panel and reduce control pod volume Turn down subwoofer s volume as program signal may be too strong Plug the subwoofer s power cord into a surge protector If there is noise or hissing and the volume is low even when the main volume is up Turn up computer s sound volume via control panel Turn down main volume on control pod to compensate Ensure that software hardware is properly installed and operating If there is computer monitor interference Make sure the sub is positioned at least 3 feet 1m from the computer monitor Increase the distance between the satellite speakers and the computer monitor WIRELESS TROUBLESHOOTING 1 Make sure sound is not muted on computer 2 Make sure volume level setting on computer amp control pod is correct 3 Make sure green LED on USB transmitter and Red LED on subwoofer are not blinking If they are press each sync button 4 Restart your music player software 5 Make sure Klipsch ProMedia 2 1 Wireless is selected as the audio playback device If not select it hit apply save and restart your music player software 6 If the above does not fix the problem leave the transmitter plugged in restart your computer and go to 1 above For more detailed information and FAQs please visit www klipsch com FCC EMC COMPLIANCE INFORMATION NOTE This equipment has been tested and found to comply with the
7. ise speaker positioning in the horizontal plane Wall stud wood screws included TROUBLESHOOTING If no sound ensure that DIN plug from Control Pod AUX input if desired speaker cables and AC power cord are securely attached Soundcard software is properly installed and functioning correctly Software is provided by the sound card manufacturer The computer sound volume is turned up and not muted Also ensure that the control pod volume is not turned to the minimum setting USB transmitter is securely connected to the computer s USB port and the LED on the USB transmitter is on not blinking It may be necessary to close and restart the music player software If you suspect a problem with the USB wireless device perform the checks as described below in the section WIRELESS TROUBLESHOOTING The LED on the Control Pod is on indicating the system has power If the LED is not on check the DIN plug and AC power cord connection Also check that the AC wall outlet or power strip has power Headphones are not connected If one or more speakers have little or no sound ensure that All cables are connected properly Connectors are fully seated in soundcard and subwoofer Main and subwoofer level controls are properly adjusted on control pod Computer software audio settings are adjusted for proper use Computer system s sound control panel volume is turned up If the satellites or subwoofer exh
8. lume control to adjust the sound level An initial setting of the main volume of 11 to 12 o clock is recommended Adjustments may be needed for best sound quality Volume Control Programs Some soundcard and or PC manufacturers may have software that must be adjusted separately from the Windows volume control Consult applicable manual for specific hardware documentation Subwoofer Level For CD or DVD output the optimum position will be indicated by the mark at 10 o clock on the sub level control Optimum sub levels and user preference may vary from source to source CONTROL POD FEATURES Headphones The 1 8 stereo headphone output jack located on the right hand side of the control pod turns off the two satellite speakers and the subwoofer output The main volume control will adjust the headphone output MP3 Aux The MP3 Auxiliary input jack is used with portable audio players This signal will be mixed with the main source The input has a 6dB input sensitivity to help compensate for the lower output voltage of some portable players If using a computer output on the Aux Input you may need to compensate for the additional gain by lowering the computer s volume level to approximately 50 To obtain the proper balance with the main signal the level adjustments in the computer software and in the portable player will need to be adjusted An example would be listening to an MP3 player while surfing the net and hearing associated sound
9. ng the cables at back of sub Bumping them could cause damage 3 Connect the DIN plug to the sub from the control satellite preamp Wire should hang down from plug 4 Connect the speakers by inserting the tinned wire leads into the subwoofer The solid black wires connect to the black spring clips the black wires with red stripes to the red spring clips 5 Plug the AC power cord into a wall outlet 6 Plug headphone mini stereo plug in headphone jack if desired 7 Plug stereo mini plug into MP3 Aux jack Plug stereo mini plug into MP3 player for example If you don t want to use the wireless connect computer to Aux In See Control Pod Features Cable not included Tes USB WIRELESS TRANSMITTER 1 Perform main system setup as described above a Set up the system plug in AC power cord and turn on power switch on rear panel of subwoofer b The red LED on rear panel of subwoofer should begin flashing 2 Connecting the USB Wireless Transmitter a The computer should already be up and running b Close the music player DVD player software if it is running c Insert the USB wireless transmitter into a USB port on the computer NOTE If there is interference between the computer case or transmitter can t be fully inserted or if you have other USB devices connected and the transmitter will not fit in an adjac
10. onnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped 15 DO NOT expose this apparatus to dripping or splashing and ensure that no objects filled with liquids such as vases are placed on the apparatus 16 To completely disconnect this apparatus from the AC Mains disconnect the power supply cord plug from the AC receptacle 17 The mains plug of the power supply cord shall remain readily operable A PND NE WN o The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the product The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electrical shock to persons WARNING To reduce the risk of fire or electrical shock do not expose this apparatus to rain or moisture WARNING No naked flame sources such as candles should be placed on the product WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING Do Not Open Risk of Elec
11. s from various websites The mixed sound may not be desirable and you will ultimately determine how you use this feature NOTE During playback of MP3s overall sound quality may be perceptibly degraded compared to other audio sources such as CD This is caused by the encoding method and quality of the MP3 file It is recommended that MP3 files be encoded at a minimum 128 bit rate SPECIFICATIONS Visit www klipsch com for more details 4 ohms minimum Subwoofer and Main volume level controls LED power indicator MP3 Aux player line input with soundcard mixing function Headphone jack Direct path interface Satellite Impedance Preamplifier Control Pod Satellite Sealed elliptical two way enclosure with 25mm polymer tweeter mated to MicroTractrix Horn and 3 long throw mid bass driver Bass reflex enclosure with front port and side firing 6 5 long throw driver sixth order enclosure design Subwoofer Amplifier High efficiency power supply and linear amplifiers designed for uncompressed full power sound Protective limiter function protects the driver and amplifier from extremely high volume playback Subwoofer Limiter ACCESSORIES All accessories are available at www klipsch com WB 1 Wall Mount Brackets While supplies last Versatile Wall Bracket 1 is made from high quality steel The clean simple design affords the most extreme angle adjustment with up to 160 degrees of movement for prec
12. trical Shock Voltages in this equipment are hazardous to life No user serviceable parts inside Refer all servicing to qualified service personnel WARNING This product is intended to be operated ONLY from the AC Voltages listed on the back panel or included power supply of the product Operation from other voltages other than those indicated may cause irreversible damage to the product and void the products warranty The use of AC Plug Adapters is cautioned because it can allow the product to be plugged into voltages in which the product was not designed to operate If the product is equipped with a detachable power cord use only the type provided with your product or by your local distributor and or retailer If you are unsure of the correct operational voltage please contact your local distributor and or retailer CAUTION Place the equipment near a main power supply outlet and make sure that you can easily access the power breaker switch PACKING LIST 2 Satellite speakers with pedestals and wires attached 1 Control pod attached to one satellite speaker 1 Subwoofer 1 USB Wireless Transmitter 1 4 inch USB Adapter Cable 1 Packet of rubber isolation feet 1 Owner s manual DOES NOT NEED SOFTWARE DISC FOR OPERATION SPEAKER PLACEMENT 1 The ProMedia 2 1 Wireless system uses a short range line of sight transmitter It was not designed to be used through walls or at distances greater than about 30 feet 2 For best
13. tween the radiator and your body This transmitter must not be co located or operating in conjunction with any other antenna or transmitter Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device To reduce potential radio interference to other users the antenna type and its gain should be so chosen that the equivalent isotropically radiated power e i r p is not more than that permitted for successful communication PRODUCT REGISTRATION Register your product online at www klipsch com register e Klipsch will keep you up to date on new products and promotions e Your personal information will never be resold e This registration information is not used for warranty purposes Please retain your receipt for warranty claims Detall Emotion For over 60 years we ve made speakers for people who are as passionate about great sound as we are That s why every Klipsch speaker is horn loaded to create a remarkably accurate listening experience for your music and movies From our smallest satellites to our acclaimed professional theater installations our speakers deliver sound that s so lifelike you have to feel it to believe it www klipsch com
Download Pdf Manuals
Related Search