KitchenAid Cooktop KGCU407V User's Manual
Contents
1. Cabinet and Countertop Only to Back Wall Cabinet Backguard Countertop Opening 30 76 2 cm KGCU407 134 4 4 cm 30 76 2 cm 30 76 2 cm 2914 74 3 cm 30 76 2 cm or 297 75 9 cm for zero clearance 36 91 4 cm KGCU462 112 3 8 cm 42 106 7 cm 36 91 4 cm 35 36 91 4 cm or KGCU463 1 4 4 cm 89 5 cm 3574 91 1 cm for KGCU467 134 4 4 cm zero clearance 48 121 9 cm KGCU482 112 3 8 cm 42 106 7 cm 48 121 9 cm 474 120 0 cm 48 121 9 cm or KGCU483 134 4 4 cm 477 121 6 cm for KGCU484 1 3 8 cm zero clearance NOTES Dimension B can be reduced by 6 15 2 cm when bottom of wood or metal cabinet is covered by not less than 0 25 6 4 mm flame retardant millboard covered with not less than No 28 MSG sheet metal 0 015 0 4 mm stainless steel 0 024 0 6 mm aluminum or 0 020 0 5 mm copper If installing a range hood above the cooktop follow the range hood instructions for dimensional clearances above the cooktop surface NOTE If backwall is constructed of a combustible material and a backguard is not installed a minimum clearance of dimension A 6 15 2 cm is required for 48 121 9 cm cooktops and cooktops with a grill Page 2 of 2 Because Whirlpool Corporation policy includes a continuous commitment to improve Dimensions are for planning purposes only For complete details see Installation Ref W10526088A Our products we reserve the right to chang2. 5 9 cm F 3 9 2 cm G 1 2 6 cm Page 1 of 2 Dimensions are for planning purposes only For complete details see Installation Ref W10526088A Instructions packed with product Specifications subject to change without notice 5 6 13 CABINET REQUIREMENTS A Grounded 3 prong outlet should be located on left hand side of the cutout 16 40 6 cm max from enclosure sidewall B 10 25 4 cm min clearance from countertop to top of the outlet C 14 35 6 cm countertop to the gas supply line D Gas supply line should be located in this area on rear or side walls or the supply line can come up B through the floor C NOTE Solid side and bottom of cutout enclosure A not shown N gi Gas and Electric Connection Locations A See chart B See chart C See chart D See chart E See chart F 18 45 7 cm min clearance upper cabinet to countertop G 34 1 9 cm back of cabinet cutout to gas opening cutout H 6 16 1 cm gas opening cutout depth I 12 31 7 cm gas opening cutout width J 22 56 5 cm cabinet cutout depth K 2 5 1 cm cabinet side to gas cutout L 6 15 2 cm min distance on both sides of the cooktop to the side wall or other combustible material above cooking surface M 24 61 0 cm cabinet depth N 7 18 4 cm cabinet depth to countertop O Notch to be equal on both sides P 13 33 0 cm upper cabinet depth Size Model A B C D E Cooktop Cutout Cooktop to Optional
3. KitchenAid commercial Style Gas Cooktop FOR THE WAY IT S MADE PRODUCT MODEL NUMBERS KGCU407V KGCU482V KGCU462V KGCU483V KGCU463V KGCU484V KGCU467V Type of Gas Natural Gas This cooktop is design certified by CSA International for use with Natural gas or after proper conversion for use with LP gas This cooktop is factory set for use with Natural gas To convert to LP gas see the Gas Conversion instructions provided in the package containing literature The model Serial rating plate located on the left underside of the cooktop burner base has information on the types of gas that can be used If the types of gas listed do not include the type of gas available check with the local gas supplier LP Gas conversion Conversion must be done by a qualified service technician No attempt shall be made to convert the cooktop from the gas specified on the model serial rating plate for use with a different gas without consulting the serving gas supplier To convert to LP gas use the LP gas conversion kit provided with the cooktop and see the Gas Conversions section Gas Supply Line e Provide a gas supply line of 3 4 1 9 cm rigid pipe to the cooktop location A smaller size pipe on longer runs may result in insufficient gas supply With LP gas piping or tubing size can be 1 2 1 3 cm minimum Usually LP gas Suppliers determine the size and materials used in the system NOTE Pipe joint compounds that resist the actio
4. e materials and specifications without notice Instructions packed with product Specifications subject to change without notice 9 6 13
5. n of LP gas must be used Do not use TEFLON tape Flexible metal appliance connector e f local codes permit a new CSA design certified 4 5 ft 122 152 4 cm long 7s 1 6 cm or 3 4 1 9 cm I D flexible metal appliance connector may be used for connecting the cooktop to the gas supply line e Must include a shutoff valve The supply line must be equipped with a manual shutoff valve This valve should be located in the same room but external to the cooktop enclosure or cabinet It should be in a location that allows ease of opening and closing Do not block access to shutoff valve The valve is for turning on or shutting off gas to the cooktop A Gas supply line B Shutoff valve open position C To cooktop Electrical A 120 volt 60 Hz AC only 15 amp fused electrical circuit is required A time delay fuse or circuit breaker is also recommended It is recommended that a separate circuit serving only this cooktop be provided T TEFLON is a registered trademark of E l Du Pont De Nemours and Company Because Whirlpool Corporation policy includes a continuous commitment to improve Our products we reserve the right to change materials and specifications without notice LOCATION REQUIREMENTS IMPORTANT Observe all governing codes and ordinances Do not obstruct flow of combustion and ventilation air It is the installer s responsibility to comply with installation clearances specified on the m
6. odel serial rating plate The model serial rating plate is located on the underside of the cooktop burner base It is recommended that a 600 CFM or larger vent hood be installed above the cooktop It is not recommended that a microwave hood combination be mounted above the cooktop The cooktop should be installed in a location away from strong draft areas such as windows doors and strong heating vents or fans All openings in the wall or floor where cooktop is to be installed must be sealed Cabinet opening dimensions that are shown must be used Given dimensions are minimum clearances IMPORTANT To avoid damage to your cabinets check with your builder or cabinet Supplier to make sure that the materials used will not discolor delaminate or sustain other damage PRODUCT DIMENSIONS A 30 76 2 cm cooktop 29 75 9 cm 36 91 4 cm cooktop 35 91 1 cm 48 121 9 cm cooktop 47 121 6 cm B 36 91 4 cm long 3 prong grounding type power supply cord C Model serial rating plate located on the underside of the cooktop burner base D Island trim or optional backguard E 27 70 5 cm G gt Side View of Cooktop F gt D lt a A 27 70 5 cm B 1 3 2 cm C 77 6 18 8 cm D Gas inlet is located 1 7 4 8 cm from the back of the cooktop burner base and 4 12 4 cm in from left hand side of the cooktop burner base E 22 5
Download Pdf Manuals
Related Search