KitchenAid 9750520 REV A User's Manual
Contents
1. A Y lt 7 Y Place rack in oven Place level on rack first side to side then front to back If range is not level adjust the leveling legs up or down until the range is level Note Oven must be level for satisfactory baking conditions OFF LO HI and turn each surface unit control knob to HI position Check the operation of the cooktop elements and indicator lights 4 5 17 Panel C 4 wire electrical connection Use this wiring method for mobile homes and whenever 4 wire installation is required VE VETT 888 Prae 88 88 m O Om nme Om wee DEHYD ROTIS START CLEAN START STOP TIMER 88 88 should appear in the clock display Press the Clock Set button TIME HR AND MIN will light up in the display 0 00 will appear and the will be flashing Press the number buttons for the correct time of day Press Start Enter button to start the clock ai ASOT Tet ai DAS J t ULL listed condult connector if appliance is to be connected directly to fused disconnect or circuit breaker box Assemble a U L listed conduit connector in the conduit connector opening provided Insert the power supply cable through the conduit connector allowing enough slack to easily attach the wiring to the terminal block Check the operation of the oven element Press the BAKE button 350 will appear in the temperature display The ON Bake Elem2. KitchenAid g a a id R Part No 9750520 Rev A 30 Electric Freestanding Range IMPORTANT Read and save these instructions IMPORTANT Installer Leave Installation Instructions with the homeowner Homeowner Keep Installation Instructions for future reference Save Installation Instructions for local electrical inspector s use Check location where range will be installed The range should be located for convenient use in kitchen ALL OPENINGS IN THE WALL OR FLOOR WHERE RANGE IS TO BE INSTALLED MUST BE SEALED 18 min clearance upper cabinet to opening countertop p width 8 to 22 from either cabinet 7 max from floor Se a f le Wall receptacle 36 countertop height D ee Do Not pinch N the power N cord between Grounded electrica outlet is required See Electrical requirements NOTE Clearances specified are for combustible walls and materials that have a density of 20 or more pounds per cubic foot No evaluation of clearances has been made for installations adjacent to materials that are less than 20 pounds per cu ft or to plastic tile or sheeting the range and the wall Do Not seal the range to the side cabinets Cabinet opening dimensions that are shown must be used Given dimensions are minimum clearances and provide required 0 clearance 13 max 30 3 8 ooo D material Important Observe a
3. for installation flat blade screwdriver or 16 inch nut driver measuring tape or ruler hand or electric drill wood metal wall stud pliers 1 8 inch drili bit concrete concrete block walls 3 16 Inch carbide tipped masonry drill bit Parts supplied for installation samy a 2 screws 10 x 1 1 2 Thickness of wall covering may require longer screws avallable from you local hardware store 2 plastic anchors anti tip bracket Panel A Electrical requirements Save Installation Instructions for the local electrical inspector s use Power cord is not supplied but is available through you local electrical supply houses A WARNING Electrical Shock Hazard Electrical ground is required on this appliance e Improper connection of the equipment grounding conductor can result in electrical shock e Check with a qualified electrician if you are in doubt as to whether the appliance is properly grounded e Only a power supply cord kit rated at 250 volts 40 amperes and investigated for use with ranges should be used Do Not have a fuse in the neutral or grounding circuit A fuse in the neutral or grounding circuit could result in electrical shock Do Not plug the pigtail power cord into a live wall receptacle before the cord Is permanently connected to the terminal block To do so may result in personal injury from electrical shock Failure to follow these instructions could result
4. whom you purchased the appliance or a KitchenAid authorized service company A KitchenAid authorized service company is listed in the Yellow Pages of your telephone directory under Appliances Household Major Service or Repair You can also obtain the service company s name and telephone number by dialing free within the continental United States the KitchenAid Consumer Assistance Center telephone number 800 422 1230 A special operator will tell you the name and number of your nearest KitchenAid authorized service company Maintain the quality built into your appliance call a KitchenAid authorized service company
5. ching over a heated cooking surface could result in a serious burn or other personal injury Electrical Shock Hazard It is the customer s responsibility e To contact a qualified electrical installer e To assure that the electrical installation is adequate and in conformance with National Electrical Code ANSI NFPA 70 latest edition and all local codes and ordinances Failure to do so could result in fire electrical shock or other personal injury Mobile home installation The installation of this range must conform to the Manufactured Home Construction and Safety Standards Title 24 CFR Part 3280 formerly the Federal Standard for Mobile Home Construction and Safety Title 24 HUD Part 280 or when such standard is not applicable the Standard for Manufactured Homes Installations 1982 Manufactured Home Sites Communities and Setups ANSI A225 1 1987 or latest edition or with local codes When this range is installed in a mobile home it must be secured to the floor during transit Any method of securing the range is adequate as long as it conforms to the standards listed above Four wire power supply cable must be used in a mobile home installation The appliance wiring will need to be revised See 4 wire electrical connection Panel C Copies of the standards listed may be obtained from National Fire Protection Association Batterymarch Park Quincy Massachusetts 02269 Tools needed
6. e drawer or door Failure to follow this instruction could result in personal injury and or product damage For cleaning and maintenance if removing the range is necessary for cleaning or maintenance disconnect the electric supply if electrical supply is inaccessible lift the range slightly at the front and pull the range away from the wall Pull the range out only as far as necessary to disconnect the electric supply line Remove the cable from the anti tip bracket and remove range to complete cleaning or maintenance Move range back into operating position Insert cable into anti tip bracket Level the range Reconnect the electrical supply Make sure that cable is secure in anti tip bracket Part No 9750520 Rev A 1996 KitchenAid Registered Trademark of KitchenAid lf you need assistance The KitchenAid Consumer Assistance Center will answer any questions about operating or maintaining your range not covered in the Installation Instructions The KitchenAid Consumer Assistance Center is open 24 hours a day 7 days a week Just dial 800 422 1230 the call is free When you call you will need the range model number and serial number Both numbers can be found on the serial rating plate located on the oven frame behind the door Prepared by KitchenAid Benton Harbor Michigan 49022 If you need service In the event that your KitchenAid appliance should need service call the dealer from
7. ent Outer Broil Element and Oven Cavity symbols will light up in the display Press the Start Enter button The bottom element should glow red and the indicator light should be on The upper element should become hot but not glow red The oven indicator light goes off when the oven is preheated Press Cancel OFF button U L llsted strain rellef shown Check the operation of the broil element Press the BROIL button 500 will appear in the temperature display The ON Inner and Outer Broil Elements and Oven Cavity symbols will light up in the display Press the Start Enter button The top element should glow red and the indicator light should be on Press the Cancel OFF button TENS gt Clamping screws If a U L listed 40 ampere range power supply cord pigtail is used Remove the knockout for the 40 ampere power supply cord Assemble a U L listed strain relief in the hole Insert the power supply cord through the strain relief allowing enough slack to easily attach the wiring to the terminal block Do not loosen the factory installed nuts already To get the most efficient use from your installed on the termina block new electric range read your KitchenAid Use and Care Guide Keep Installation Instructions and Guide close to the electric range for easy reference Grounding link screw V eN Grounding link Remove the grounding link screw from the range frame Save the gro
8. he 3 8 brass nuts taped to cabinet below the terminal block Be sure the wiring nuts are installed tight Use this wiring method ONLY if local codes permit connecting cabinet grounding conductor to neutral wire of power cord This appliance is manufactured with the neutral terminal connected to the cabinet If local codes Do Not permit grounding through the neutral a four wire power supply cord rated 250 volts 40 amperes and investigated for use with ranges must be used See 4 wire electrical connection Panel C Connect the neutral white wore to the silver colored terminal screw on the terminal block Connect the other two wires to the outer terminal screws on the terminal block Use ring type terminals only Connect with the brass nuts attached to the range Do Not loosen factory installed nuts already on the terminal Check that nuts are tight to insure proper electrical connection Tighten the strain relief clamping screws or the locking ring and clamping screws of the conduit connector Replace terminal block cover WARNING e To prevent tipping install range anti tip bracket Anti tip bracket must be attached to a wood or metal wall stud or concrete or concrete block wall Do Not attach anti tip bracket to a cabinet Save these Installation Instructions If range is moved to a new location the anti tip bracket must be removed and reinstalled in the new location centerline wall s
9. in a fire electrical shock or personal injury A three wire or a four wire single phase 120 240 volt 60 Hz AC only electrical supply or three wire or four wire 120 208 volt if specified on serial plate is required on a separate 40 ampere circuit fused on both sides of the line A time delay fuse or circuit breaker is recommended THE RANGE MUST BE CONNECTED WITH COPPER WIRE ONLY Local codes may permit the use of a U L listed 250 volt 40 ampere range power supply cord pigtail This cord contains three No 10 copper wires and matches a three wire receptacle of NEMA Type 10 50R shown in Figure 1 Connectors on the appliance end must be ring terminals A U L listed strain relief must be provided at the point the power supply cord enters the appliance The appliance should be connected directly to the fused disconnect or circuit breaker box through flexible armored or non metallic sheathed copper cable Allow two or three feet of slack in the line so that it can be moved if servicing is ever necessary A U L listed conduit connector must be provided at each end of the power supply cable at the appliance and at the junction box Wire sizes COPPER WIRE ONLY and connections must conform with the rating of the appliance 40 amperes E IF CONNECTING TO A 4 WIRE ELECTRICAL SYSTEM This appliance is manufactured with ground connected to cabinet The ground must be revised so the g
10. ll governing codes and ordinances upper cabinet depth gt For minimum clearance see Note 4 Min PA countertop space to side wall or other combustible od lt a 88 O Hee a 0 26 3 8 depth 3 with handle a 36 cooktop height metal cabinet 46 13 16 overall helght Note 24 min when bottom of wood or metal cabinet is protected by not less than 1 4 flame retardant millboard covered with not less than pne ant ipo No 28 MSG sheet steel 0 015 be installed For stainless steel 0 024 aluminum or detalled 0 020 copper instructions 30 min clearance between the top see Panels B of the cooking platform and the and C bottom of an unprotected wood or Before you start Proper installation is your responsibility A qualified technician should install this range Make sure you have everything necessary for correct installation It is the responsibility of the installer to comply with installation clearances specified on the serial rating plate The serial rating plate is located on the oven frame behind the oven door AX WARNING Personal Injury Hazard Avoid installing cabinet storage above the cooking surface If cabinets are already installed reduce the hazard of reaching over a heated cooking surface by installing a range hood The range hood should extend a minimum of 5 inches out from the bottom front of the cabinets Rea
11. on anti tip bracket with mark on wall Use a pencil to mark the location of the top and bottom mounting holes Remove bracket If wall covering is ceramic tile drill a 3 16 inch hole through tile only Then proceed as follows For wood or metal wall studs Drill 1 8 holes at each mounting hole location through wall and into stud For concrete or concrete block wall Drill 3 16 holes 1 3 4 inch minimum deep at each mounting hole location Tap plastic anchors into mounting holes with hammer holes on bracket with holes on wall making sure that the TOP mounting hole on bracket is lined up with top hole in wall Securely fasten bracket to wall using screws provided Plug range power supply cord into grounded outlet Carefully slide range into position until range is approximately 2 inches from rear wall Remove shipping base cardboard or hardboard from under the range Push cable located on rear of range up and into the two hooks on the anti tip bracket Check that cable is secure in both hooks by pulling cable towards range If cable comes out of hooks reposition cable to insure that cable fits securely in both anti tip bracket hooks Slide range into final position If installing the range in a mobile home you MUST secure the range to the floor Any method of securing the range is adequate as long as it conforms to the standards listed in the Mobile Home Installation Instructions Panel A
12. reen grounding wire of the 4 wire power cord is connected to the cabinet See 4 wire electrical connection section Panel C When a 4 wire receptacle of NEMA type 14 50R is used See Figure 2 a matching U L listed 4 wire 250 volt 40 ampere range power supply cord pigtail must be used This cord contains four copper conductors with ring terminals on the appliance end terminating in a NEMA Type 14 50P plug on the supply end The fourth grounding conductor must be identified by a green or green yellow cover and the neutral conductor by a white cover Cord should be Type SRD or SRDT with a U L listed strain relief and be at least four feet long The MINIMUM conductor sizes for the copper 4 wire power cord are 40 ampere circuit 2 No 8 conductors 1 No 10 white neutral 1 No 8 green grounding The wiring diagram is also located on the back of the range a UG K oY xi w 3 wire wall 4 wire wall receptacle receptacle 10 50R 14 50R Figure 1 Figure 2 Now start With range in kitchen Remove racks and other parts from inside oven l l Take 4 cardboard corners from the carton Stack one cardboard corner on top of another Repeat with other two corners Place corners lengthwise on the floor in back of range Firmly grasp the range and gently lay it on its back on the cardboard corners Pull cardboard shipping base firmly to remove Use adjustable wrench to loosen leveling legs fo
13. tud C To mount anti tip bracket to wood or metal wall stud Find the wall stud that is closest to the center of the range location Note Wall stud should Not be more than 12 inches to the right or teft of center of range location Measure and mark at the center of the wall stud a distance of 44 inches up from the floor To mount anti tip bracket to concrete or concrete block wall Measure and mark on the rear wall at the center of the range location a distance 44 inches up from the floor Note Anti tip bracket can Not be installed more than 12 inches to the right or left of center of range location WARNING Electrical Shock Hazard e Take special care when drilling holes into the wall Electrical wires may be concealed behind the wall covering e Locate the electrical circuits that could be affected by the installation of this bracket and turn off the power to these circuits Failure to follow these instructions may result in electrical shock or other personal injury CAUTION Property Damage e Contact a qualified installer for the best procedure to drill mounting holes through the type of wall covering i e ceramic tile and into wall stud concrete or concrete block wall Before moving range across floor check that range is on shipping base or slide range onto cardboard or hardboard Failure to follow these instructions may result in damage to wall or floor covering the TOP mounting hole
14. unding screw Bend up the grounding link so that it does not contact the range 19 20 21 22 Grounding Green screw insulated wire Connect the green grounding wire to the range using the grounding screw Numbers removed in Step B The green grounding wire must be attached first and must not contact any correspond other terminal to steps Sllver colored terminal block screw Neutral white Green wire insulated wire ULL listed strain rellef shown Connect the neutral white wire to the center silver colored terminal screw on the terminal block Connect the other two wires to the outer terminals on the terminal block Use ring type terminals only Connect and securely tighten the brass nuts that are provided on a plastic strip attached to the range Do Not loosen the factory installed nuts already on the terminal Be sure that the nuts are installed tight E l Tighten the strain relief clamping screws or the locking ring and clamping screws of the conduit connector Replace the terminal block cover Continue installation at Step 12 Panel B If the range does not operate e Check that the circuit breaker is not tripped or the fuse blown Check that power supply cord is plugged into wall receptacle NOTE Refer to Use and Care Guide for operating instructions and cleaning instructions WARNING Personal Injury Product Damage Hazard Do Not step lean or sit on the rang
15. ur complete turns Place cardboard or hardboard in front of range Stand range back up Remove the shipping materials including tape and protective film from range i N Pui R Ba AP terminal nuts Remove the terminal block cover located on the back of range Panel B 3 wire electrical connection See Panel C for 4 wire electrical connection Conduit connector WW ee 1 S N Knock out opening opening for 40 ampere power supply cord 7a m W PNR conduit connector If appliance is to be connected directly to fused disconnect or circuit breaker box Assemble a U L listed conduit connector in the conduit connector opening provided Insert the power supply cable through the conduit connector allowing enough slack to easily attach the wiring to the terminal block Silver colored terminal block screw Grounding link Line 1 U L listed strain relief and 40 ampere range power supply cord shown If a U L listed 40 ampere range power supply cord pigtail is used Remove the knockout for the 40 ampere power supply cord Assemble a U L listed strain relief in the hole Insert the power supply cord through the strain relief allowing enough slack to easily attach the wiring to the terminal block Do not loosen the factory installed nuts already installed on the terminal block Use only ring type terminals to connect the power supply To secure the power supply cord use t
Download Pdf Manuals
Related Search