Kidde 1798 User's Manual
Contents
1. 001773 001786 001787 001788 001789 001790 001798 Mounting the Lock using the flush mount option requires the use of a mounting bracket 1 Use Template B to determine the dimensions and hole locations 2 Position the Lock and mounting bracket in place and install the four 6 32 torx Body Screws through the bracket into the Lock body and tighten Do not exceed 15 in lb of torque Note The screws are designed to cut threads into the Lock body as they are installed 3 Attach the mounting bracket to the panel with your choice of fasteners through the four holes RN at the outer corners of the bracket Lock with Bracket 4 Proceed to Cam Installation Section Ill Option C Flush Mount with Bracket Thick Panel Strikeplate Use Option C for the following models ONLY 001827 001828 001829 001830 001831 001832 001833 001834 This mounting option is intended for panels of 3 4 1 16 thickness and requires the use of a thick panel bracket 1 Use Template C to determine the dimensions and hole locations make sure the cam outline extends 1 4 beyond the door edge 2 Cut the hole for the Lock and four corner holes using the template as a guide 3 Mount the backplate to the Lock using the four body screws torque should not exceed 15 in lbs 4 Position the faceplate flush to the front of the cabinet aligning the plate with the four corner holes 5 Insert the Lock with backplate into the large hole2. TouchPoint Lock E rot Kidde Al ais reserved Mounting Instructions The TouchPoint Lock is a pushbutton access control device that permits authorized entry into cabinets drawers or other locking enclosures The TouchPoint Lock is easy to install on a variety of cabinets or enclosures and is intended for both indoor and outdoor applications The TouchPoint Lock can be ordered as a single component or with optional mounting hardware including mounting brackets for sheet metal or thick panels 90 or 180 stop cams a straight cam 1 1 8 length or offset cam 1 5 8 length 5 16 offset The variations depend on the type of cabinet or enclosure to which the lock is mounted Tools Needed Recommended Standard Hardware Provided e Drill e Hole saw For Top Mount Option 10 24 x 1 4 Cam Screw e Router For Flush Mount Options D combination drive 1 e File e Philips screwdriver 0 10 Round flat washer 1 e 715 Torx driver e Pen or pencil 6 32 x 5 16 Body Screw T15 torx drive 4 I Mounting Options The TouchPoint Lock can be oriented vertically or horizontally to permit a wide range Available of locking options Hardware The TouchPoint Lock has three mounting options top mount flush mount with a sheet metal bracket and flush mount with a thick panel bracket In the top mount option the back face of the Lock housing is mounted on the front face of the cabi net or enclosure In the two flush mount o
3. button Lock Instructions to set the combination for the lock Do not set the code with the Lock in the open position 3 38 VI Template Cutouts 4 55 V NS 0 781 4x 0169 lt 1 50 gt Template B Sheet Metal Bracket 664 2 750 1 320 Template A Top Mount 4 X R 0 36 For Reference Only t os wa 4 X 0 25 THRU l Cut Here 3 60 se a Template C Thick Panel Bracket Vertical Mount 4XR 0 36 eI ee For Reference Only oe 2X0 25 THRU Cut Here Template C Thick Panel Bracket Horizontal Mount
4. ptions the front face of the Lock housing is aligned flush with the front face of the cabinet or enclosure secured by a bracket 180 Stop 90 Stop Straight Offset inside a hole cut into the cabinet surface Washer Washer Cam Cam In each of these options the lock is secured to the panel or bracket through the use of thread rolling screws into bosses on the Lock housing Any mounting scheme should be designed Cabinet so that the mounting fasteners cannot be removed or tampered with when the Lock is mounted and the cabinet or enclosure is closed and locked ll Mounting Instructions Option A Top Mount For use on panels of 1 8 thickness or less 1 If the cabinet has an existing lock remove the existing lock cylinder If the open ing is too small for the protrusion on the back of theTouchPoint lock use a file to round out the lock tail hole 2 If the cabinet does not have an existing lock use Template A to determine the dimensions and hole locations 4 Position the Lock over the holes and install the four body screws through the back of the cabinet and into the Lock body Do not exceed 15 in lb of torque Note The screws are designed to cut threads into the Lock body as they are installed Lock Body 5 Proceed to Cam Installation Section Ill Top Mount Side View Option B Flush Mount with Bracket Sheet Metal Cabinet Use Option B for the following models ONLY 001764 001765 001766 001767 001768
5. through the back side of the Shim Optional 2 cabinet Check for any gaps between the backplate and cabinet If a gap is present use the shims provided to Till the space between the backplate and cabinet EDD E Flat Phillips 2 3 4 Phillips Lock Washer 6 Attach the backplate to the faceplate by installing the four Phillips screws and lock 2 4 2 4 washers into the four corner holes in the backplate and tightening 7 To mount the strikeplate measure 1 35 in from the cabinet face and cut a rectan gular hole Drill two 1 16 pilot holes and mount with the two flat phillips screws Cam Arm 8 Proceed to Cam Installation Section III Cam c3 Screw Round Ill Cam Installation UN Washer The Lock includes a camshaft which extends from the back of the Lock body and ends in a 5 16 square protrusion designed to mount and orient the cam arm An optional 90 or 180 stop washer must be used between the cam arm and Lock body to limit the rotation of the cam Lock Body The stop washer cam arm and round washer are secured to the Lock using the 10 24 Cam Screw IV Clutch and The Lock contains a clutch mechanism that guards against 4X0 19 THRU forced entry If the clutch becomes disengaged during the optional for use of this product simply rotate the Open lever to its home press in studs position to reset the clutch 4XR 25 K po V After Installation es is Complete lt gt Follow the TouchPoint Push
Download Pdf Manuals
Related Search