Kenwood KVT-536DVDM User's Manual
Contents
1. Frame 2 Insert the two removal tools deeply into the slots on each side as shown Removal Tool Accessory 3 Lower the removal tool toward the bottom and pull out the unit halfway while pressing towards the inside Be careful to avoid injury from the catch pins on the removal tool 4 Pull the unit all the way out with your hands being careful not to drop it Installing in Japanese made Cars Installation on Toyota Nissan or Mitsubishi Car using Brackets at Holes shown by Accessory 6 M5x6mm or Accessory 6 M5x7mm Car Bracket Accessory 5 M5x6mm or Accessory 6 M5x7mm Screws included in audio unit package Screws included in Audio unit or others audio unit package Do not use your own screws Use only the screws provided If you use the wrong screws you could damage the unit English 9 Installing in Japanese made Cars Installation on Toyota Car using Brackets at Holes shown by When using the bracket shown above you cannot use screws at two holes of the right and left unit sides 1 Mount the bracket at each side Car Bracket Accessory 5 M5x6mm Screws included in audio unit package Screws included in audio unit package 2 Bend each end of case to fix the bracket Use a flat blade screwdriver or pliers and bend each case tab into the h2. KENWOOD MONITOR WITH DVD RECEIVER KVT 536DVD KVT 536DVDM INSTALLATION MANUAL Accessories 2 KVT 536DVD KVT 536DVDM Installation Procedure 1 To prevent a short circuit remove the key from the ignition and disconnect the battery 2 Make the proper input and output wire connections for each unit Connect the speaker wires of the wiring harness Connect the wiring harness wires in the following order ground battery ignition Connect the wiring harness connector to the unit Install the unit in your car Reconnect the battery Press the reset button gt ONAN AWARNING If you connect the ignition wire red and the battery wire yellow to the car chassis ground you may cause a short circuit that in turn may start a fire Always connect those wires to the power source running through the fuse box ACAUTION Install this unit in the console of your vehicle Do not touch the metal part of this unit during and shortly after the use of the unit Metal part such as the heat sink and enclosure become hot A Mounting and wiring this product requires skills and experience For safety s sake leave the mounting and wiring work to professionals Make sure to ground the unit to a negative 12V DC power supply Do not install the unit in a spot exposed to direct sunlight or excessive heat or humidity Also avoid places with
3. USB terminal To KCA BT200 I Optional Accessory Connection cable Included in the Navigation System TV Tuner Optional Accessory Navigation System Optional Accessory lt lt N S11 7 Connection cable Included in the TV tuner Navigation units that can be connected to this unit As of December 2009 KNA G630 KNA G630CN For latest information access the www kenwood com cs ce 6 KVT 536DVD KVT 536DVDM Installation Removing the Unit Installation Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place E Make sure that the unit is installed securely in place If the unit is unstable it may malfunction eg the sound may skip English 7 Installation Removing the Unit Removing the Hard Rubber Frame escutcheon 1 Engage the catch pins on the removal tool and remove the two locks on the lower level Lower the frame and pull it forward as shown in the figure Escutcheon Accessory Removal Tool Accessory The frame can be removed from the top side in the same manner 2 When the lower level is removed remove the upper two locations 8 KVT 536DVD KVT 536DVDM Removing the Unit 1 Remove the hard rubber frame by referring to the removal procedure in the section lt Removing the Hard Rubber
4. ar output terminals do not mix front and rear For example if you connect the B connector of the left speaker to a front output terminal do not connect the connector to a rear output terminal After the unit is installed check whether the brake lamps blinkers wipers etc on the car are working properly Mount the unit so that the mounting angle is 30 or less This unit has the cooling fan page 5 to decrease the internal temperature Do not mount the unit in a place where the cooling fan of the unit are blocked Blocking these openings will inhibit the cooling of the internal temperature and result in malfunction English 3 Connecting Wires to Terminals Ignition key switch ACC Battery wire Yellow Igniti ire Red ga gnition wire Red h Car fuse box Car fuse box Main fuse Ground wire Black To car chassis Batterv USB device commercially available USB connector gt A Ifyou connect the ignition wire red and the battery wire yellow to the car chassis ground you may cause a short circuit that in turn may start a fire Always connect those wires to the power source running through the fuse box m FUSE CISA E Connect to the vehicle s parking brake detection switch harness arking sensor wire Light Green PRK SW For the sake of safety be sure to
5. connect the parking sensor Reverse sensor wire Purple White Connect to vehicle s reverse lamp harness when using the optional rear view camera Dimmer control wire Orange White To car light control switch Steering remote control input Light Blue Yellow ED To use the steering wheel remote control feature you need to an exclusive remote adapter not To steering remote supplied matches your car is required Connect to the terminal that is grounded when either Mute wire Brown E To connect the Kenwood navigation system consult your navigation manual Depending on what antenna you are using connect either to the control terminal of the motor antenna or to the power terminal for the booster otor antenna control wire Blue amplifier of the film type or short pole type antenna When using the optional power amplifier ower control wire Blue White the telephone rings or during conversation connect to its power control terminal SPOT If no connections are made do not let the cable come out from the tab 4 KVT 536DVD KVT 536DVDM REVERSE ILLUMI STEERING WHEEL REMOTE CONT REMOTE INPUT MUTE ANT CONT Wiring harness Accessory Cooling fan An
6. ole of installation bracket to fix the bracket 10 KVT 536DVD KVT 536DVDM KENWOOD
7. tenna Cord q FM AM antenna input Audio Visual input Rear View Camera Input Visual input Yellow DI Audio left input White Audio right input Red Audio Visual Output Visual output Yellow Audio left output White 0 Audio right output Red Rear Subwoofer Preout Audio left output White Audio right output Red Front Preout Audio left output White Audio right output Red P CONT Green Purple Blac Purple eft speaker Wiring harness AV IN Accessor o REAR VIEW CAMERA AV OUT REAR SUB WOOFER FRONT White Blac e e HI To front White Gray B ray Black o Y o HI To front right speaker Grav Green Blac HI To rear left speaker HI To rear right speaker LIR English 5 Optional Accessory Connection iPod commercially available KCA iP301V Optional Accessory Audio Input Resistance free stereo type mini plug 3 50 Pod NIOIaNV Audio Output Black Visual Input Yellow Resistance free mini plug 3 50 Visual Output Yellow USB terminal
8. too much dust or the possibility of water splashing Do not use your own screws Use only the screws provided f you use the wrong screws you could damage the unit f the power is not turned ON PROTECT is displayed he speaker wire may have a short circuit or touched the chassis of the vehicle and the protection function may have been activated Therefore the speaker wire should be checked f your car s ignition does not have an ACC position connect he ignition wires to a power source that can be turned on and off with the ignition key If you connect the ignition wire to a power source with a constant voltage supply as with battery wires the battery may die f the console has a lid make sure to install the unit so that he faceplate will not hit the lid when closing and opening f the fuse blows first make sure the wires aren t touching cause a short circuit then replace the old fuse with one with the same rating Insulate unconnected wires with vinyl tape or other similar material To prevent a short circuit do not remove the caps on the ends of the unconnected wires or the terminals Connect the speaker wires correctly to the terminals to which they correspond The unit may be damaged or fail to work if you share the wires or ground them to any metal part in the car When only two speakers are being connected to the system connect the connectors either to both the front output terminals or to both the re
Download Pdf Manuals
Related Search