Home

Kenwood KDC-W3537 User's Manual

1. Program Type preset Putting the Program Type in the Preset button memory and quick recall Presetting the Program Type 1 Select the Program Type to preset Refer to lt PTY Program Type gt page 14 2 Preset the Program Type Press the desired 1 6 button for at least 2 seconds Recalling the preset Program Type 1 Enter PTY mode Refer to lt PTY Program Type gt page 14 2 Recall the Program Type Press the desired 1 6 button Changing Language for PTY Function Selecting the Program Type display language 1 Enter PTY mode Refer to lt PTY Program Type gt page 14 2 Enter Changing Language mode Press the TI button 3 Select the language Push the Control knob towards FM or AM Each time you push the knob the language alternates between the languages shown in the table below Language Display English ENGLISH French FRENCH German GERMAN 4 Exit Changing Language mode Press the TI button English 15 CD Audio file External disc control features TOW 2 2a o amp SCAN RDM REP F SEL M RDM SRC 3 Control knob Disc number IN indicator Track number Playing CD amp Audio file When a disc is inserted Press the SRC button Select the CD display When a CD is inserted the IN indicator is ON Pause and play Press the Control knob Each time you press the knob the audio pauses or plays E
2. 30 English Purple Purple Black Gray Gray Black White White Black Green Green Black Rear Right Rear Right Front Right Front Right Front Left Front Left Rear Left Rear Left AWARNING Connecting the ISO Connector The pin arrangement for the ISO connectors depends on he type of vehicle you drive Make sure to make the proper connections to prevent damage to the unit The default connection for the wiring harness is described in 1 below If the ISO connector pins are set as described in 2 or 3 make the connection as illustrated Please be sure to reconnect the cable as shown 2 below to install this unit to the Volkswagen vehicles etc o Default setting The A 7 pin red of the vehicle s ISO connector is linked with the ignition and the A 4 pin yellow is connected to the constant power supply Ignition cable Red A 7 Pin Red o gt ae Unit Vehicle wl a Battery cable Yellow A 4 Pin Yellow N The A 7 pin red of the vehicle s ISO connector is connected to the constant power supply and the A 4 pin yellow is linked to the ignition Ignition cable Red A 7 Pin Red a Unit a Vehicle Ba gt Battery cable A 4 Pin Yellow Yellow w The A 4 pin yellow of the vehicle s ISO connector is not connected to anything while the A 7 pin red is
3. and lt Languages to be displayed gt in lt Programme Type PTY Function gt At the operation to press DISP button use TI button instead lt Automatic Switching DAB priority gt This function cannot be used 6 English This Product is not installed by the manufacturer of a vehicle on the production line nor by the professional importer of a vehicle into an EU Member State Information on Disposal of Old Electrical and Electronic Equipment applicable for EU countries that have adopted separate waste collection systems Products with the symbol crossed out wheeled bin cannot be disposed as household waste Old electrical and electronic equipment mmm Should be recycled at a facility capable of handling these items and their waste byproducts Contact your local authority or details in locating a recycle facility nearest to you Proper recycling and waste disposal will help conserve resources whilst preventing detrimental effects on our health and the environment The marking of products using lasers Except for some areas CLASS 1 LASER PRODUCT The label is attached to the chassis case and says that the component uses laser beams that have been classified as Class 1 It means that the unit is utilizing laser beams that are of a weaker class There is no danger of hazardous radiation outside the unit General features Release button VOL Control knob ATT i
4. Each time you press the knob the item to be adjusted alternates between the items shown in the table below 4 Adjust the Audio setup item Turn the VOL knob Adjustment Item Display Low Pass Filter LPF Volume offset V OFF Volume offset Sets each source s volume as a difference from the basic volume Function of KDC W4037 Range 80 120 160 Through Hz 8 0 AUX 8 8 5 Exit Audio Setup mode Press the VOL knob for at least 1 second Bass Boost Bass sound can be enhanced by one touch operation Press the B BOOST button When you press the button once the current Bass Boost setting is displayed Each time you press the button the Bass Boost setting alternates Setting Display Bass Boost 1 BB L L1 Bass Boost 2 BB L L2 Bass Boost off BB L OFF Speaker Setting In CD amp External disc source Fine tuning so that the System Q value is optimal Information Display when setting the speaker type Disc title D TITLE Track title T TITLE 1 Enter Standby Play time amp Track number PTIME Press the SRC button Clock CLOCK Select the STANDBY display 2 Enter Speaker Setting mode In Audio file source Press the VOL knob Information Display Song title amp Artist name TITLE 3 Select the Speaker type Album name amp Artist name ALBUM Turn the VOL knob 7 i i Folder name FOLDER Eac
5. Selecting the display when alternating to Auxiliary input source 1 Select Auxiliary input source Press the SRC button Select the AUX AUX EXT display 2 Enter Menu mode Press the MENU button for at least 1 second MENU is displayed 3 Select Auxiliary input display setting mode Push the Control knob towards FM or AM Select the NAME SET display 4 Enter Auxiliary input display setting mode Press the Control knob for at least 1 second The selected Auxiliary input display is displayed 5 Select the Auxiliary input display Push the Control knob towards ka a or gt gt Each time you push the knob the display alternates as listed below 24 English AUX AUX EXT DVD PORTABLE GAME VIDEO TV 6 Exit Auxiliary input display setting mode Press the MENU button When operation stops for 10 seconds the name at that time is registered and the Auxiliary input display setting mode closes You can only set the Auxiliary input display when the auxiliary input of optional KCA S220A is used Text Scroll Setting the displayed text scroll Display Setting SCL MANU Doesn t scroll SCL AUTO Scrolls when the display changes The text scrolled is listed below CD text Folder name File name Song title Artist name Album name MD title Radio text Function of KDC W4037 KDC W3537 KDC W3037 KDC W311 KDC W237 Russian sales area In Stand
6. when the antenna cord has an ISO plug ake sure that all wire connections are securely made by inserting jacks until they lock completely f your vehicle s ignition does not have an ACC position or if the ignition wire is connected to a power source with constant voltage such as a battery wire the power will not be linked with the ignition i e it will not turn on and off along with the ignition If you want to link the unit s power with the ignition connect the ignition wire to a power source that can be turned on and off with the ignition key If the fuse blows first make sure that the wires have not caused a short circuit then replace the old fuse with one with the same rating Insulate unconnected wires with vinyl tape or other similar material To prevent short circuits also do not remove the caps on the ends of the unconnected wires or the terminals Connect the speaker wires correctly to the terminals to which they correspond The unit may receive damage or fail to work if you share the wires and or ground them to any metal part in the car After the unit is installed check whether the brake lamps indicators wipers etc on the car are working properly If the console has a lid make sure to install the unit so that the faceplate does not hit the lid when closing and opening Mount the unit so that the mounting angle is 30 or less Connecting Wires to Terminals To Steering remote KDC W4037 KDC W
7. connected to the constant power supply or both the A 7 red and A 4 yellow pins are connected to the constant power supply Ignition cable Red A 7 Pin Red Bd Unit Re Biaoep Vehicle Battery cable Yellow A 4 Pin Yellow When the connection is made as in 3 above the unit s power will not be linked to the ignition key For that reason always make sure to turn off the unit s power when the ignition is turned off To link the unit s power to the ignition connect the ignition cable ACC red to a power source that can be turned on and off with the ignition key Installation Removing the Unit Installation Metal mounting strap commercially available Firewall or metal support Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place Self tapping screw commercially available Screw M4X8 commercially available Make sure that the unit is installed securely in place If the unit is unstable it may malfunction for example the sound may skip Removing the hard rubber frame 1 Engage the catch pins on the removal tool and remove the two locks on the upper level Upper the frame and pull it forward as shown in the figure Accessory Removal tool 2 When the upper level is removed remove the lower two locations The frame can be removed from the bottom side in the same manner Removing the Unit 1 Refer to
8. folder recorded on the Audio file media Push the Control knob towards FM or AM Accessory of KDC W4037 KDC W3537 Function of remote control Direct Track File Search Doing Track File Search by entering the track file number 1 Enter the track file number Press the number buttons on the remote control 2 Do Track File Search Press the ka a or gt gt button Cancelling Direct Track File Search Press the gt I button Function of KDC W4037 KDC W3537 Function of disc changers with remote control Direct Disc Search Doing Disc Search by entering the disc number 1 Enter the disc number Press the number buttons on the remote control 2 Do Disc Search Press the or button Cancelling Direct Disc Search Press the gt I button Input 0 to select disc 10 English 17 CD Audio file External disc control features Track File Disc Folder Repeat Replaying the song disc in the Disc changer or Audio file folder you are listening to Press the REP button Each time you press the button the Repeat Play alternates between the modes shown in the tables below In CD amp External disc source Repeat play Display rack Repeat TRAC REP isc Repeat In Disc Changer DISC REP OFF REP OFF In Audio file source Repeat play Display File Repeat FILE REP Folder Repeat FOLD REP OFF REP OFF Scan Play Playing the first part of each song on t
9. the section lt Removing the hard rubber rame gt and then remove the hard rubber frame 2 Remove the screw M4 x 8 on the back panel 3 Insert the two removal tools deeply into the slots on each side as shown 4 Lower the removal tool toward the bottom and pull out the unit halfway while pressing towards he inside Screw M4X8 commercially available Accessory Be careful to avoid injury from the catch pins on the removal tool 5 Pull the unit all the way out with your hands being careful not to drop it English 31 Troubleshooting Guide Some functions of this unit may be disabled by some settings made on this unit 1 Cannot switch to Aux source P AUX is not turned on 1 gt lt Built in Auxiliary input Setting gt page 25 1 Cannot display the user of System Q P lt Audio Control gt page 8 is not set 1 Cannot set up the subwoofer No output from the subwoofer Cannot set up the low pass filter P Preout is not set to subwoofer lt Switching preout gt page 22 lt Subwoofer Output gt page 9 is not set to On a Cannot register a security code e Cannot set up Display gt lt Demonstration mode Setting gt page 25 is not turned off 1 Cannot set up the Power off timer P lt Security Code gt page 20 is not set a Cannot play audio files P lt CD Read Setting gt page 25 is set to 2 32 English What might seem to be a malfunction in your unit may ju
10. 3537 Western European countries sales area only we To Kenwood disc changer External optional accessory i KDC W4037 KDC W3537 only To connect these leads refer to the relevant instruction manuals FM AM antenna input lt lt OS Antenna Cord ISO Antenna Conversion Adaptor ISO JASO Accessory Fuse 10A o Rear left output Sub Woofer left output White Wiring harness Rear right output Sub Woofer right output Red Accessory KDC W4037 only F Connect to the terminal that TEL mute wire Brown is grounded when either the telephone rings or during conversation oD To connect the Kenwood navigation system consult If no connections are made do dane 7 your navigation manual not let the wire come out from the tab Power control Motor antenna control wire Connect either to the power Blue White control terminal when using the optional power amplifier or to E ANTCONT the antenna control terminal in the vehicle Battery wire Yellow Ignition wire Red See next page Wy A 7 Pin Red A 4 Pin Yellow lt n Connector A Connector B English 29 Connecting Wires to Terminals Connector Function Guide Pin Numbers for ISO Connectors Cable Colour Functions External Power Connector A 4 A 5 A 7 A 8 Yellow Blue White Red Black Battery ower Control gnition ACC Earth Ground Connection Speaker
11. C button 2 Enter Audio Control mode Press the VOL knob 3 Select the Audio item to adjust Press the VOL knob Each time you press the knob the item to be adjusted alternates between the items shown in the table below 4 Adjust the Audio item Turn the VOL knob Adjustment Item _ Display Range Subwoofer level SW L 15 15 System Q NATURAL ROCK Natural Rock Pops Easy POPS EASY Top 40 Jazz T0P40 JAZZ Bass level BAS L 8 8 Middle level MID L 8 8 Treble level TRE L 8 8 Balance BAL Left 15 Right 15 Fader FAD Rear 15 Front 15 Exit Audio Control mode Volume control mode About System Q You can recall the best sound setting preset for different types of music Change each setting value with the lt Speaker Setting gt page 9 First select the speaker type with the Speaker setting USER This appears when Bass level Middle level and Treble level are adjusted When USER is selected these levels are recalled Function of KDC W4037 5 Exit Audio Control mode Press any button 8 English Press a button other than the VOL knob and ATT button Audio Setup Setting the Sound system such as Volume offset 1 Select the source to adjust Press the SRC button 2 Enter Audio Setup mode Press the VOL knob for at least 1 second 3 Select the Audio Setup item to adjust Press the VOL knob
12. DC W4037 In Standby mode Switching preout Alternating the preout between the rear and subwoofer With the subwoofer the sound outputs without being effected by fader control Display Setting SWPRE R Rear preout SWPRE SW Subwoofer preout In Audio file source Supreme Setting When MP3 or WMA files encoded at a low bit rate less than 96kbps fs 32k 44 1k 48kHz are played this function restores their high frequency region to approach the sound quality of equivalents of these files encoded at a high bit rate Processing is optimized for the compression format used MP3 or WMA and adjustment is made for the bit rate used Display Setting SPRM ON Plays sound using the Supreme function SPRM OFF Plays the original sound stored in the audio file The sound effect may be imperceptible depending on the relationship between the audio file format and setting Function of KDC W4037 KDC W3537 KDC W3037 KDC W311 News Bulletin with Timeout Setting The tuner automatically changes when a news bulletin starts even if the radio is not being listened to Also you can set the time interval when interruption is prohibited Display and Setting NEWS OFF NEWS 00M NEWS 90M When you set NEWS 00M NEWS 90M the News Bulletin Interrupt function is ON When the News Bulletin is ON the NEWS indicator is ON When the news bulletin starts NEWS is displayed an
13. EP ON or BEEP OFF Select 1 of them as the setting You can continue by returning to step 2 and setting other items 20 English 4 Exit Menu mode Press the MENU button When other items those applicable to the basic operation method above are displayed their setting content chart is entered Normally the setting listed at the top of the chart is the original setting Also the explanation for items that are not applicable lt Manual Clock Adjustment gt etc are entered step by step Function of KDC W4037 KDC W3537 In Standby mode Security Code Activating the Security Code disables the usage of audio unit by someone else Once the Security Code is activated the entry of authorized Security Code is required to turn on the audio unit when it is removed from the vehicle Indication of this Security Code activation prevents your precious audio unit from stealing When you activate the Security Code function it cannot be released Note your Security Code is the 4 digit number entered in your Car Audio Passport in this package 1 Enter Standby Press the SRC button Select the STANDBY display 2 Enter Menu mode Press the MENU button for at least 1 second When MENU is displayed CODE SET is displayed 3 Enter Security Code mode Press the Control knob for at least 1 second When ENTER is displayed CODE is also displayed 4 Select the digits to enter Push the Control knob toward
14. KENWOOD CD RECEIVER Kenwood Corporation Contents Safety precautions 3 Menu system 20 enu System Notes 4 secu Cal Touch Sensor Tone General features 7 anual Clock Adjustment Power Synchronize Clock Selecting the Source DSI Disabled System Indicator Volume Selectable Illumination Attenuator Dimmer Audio Control Switching preout Audio Setup Supreme Setting Bass Boost ews Bulletin with Timeout Setting Speaker Setting Local Seek Switching Display Tuning Mode Subwoofer Output AF Alternative Frequency Theft Deterrent Faceplate Restricting RDS Region Region Restrict Function TEL Mute Auto TP Seek onaural Reception Tuner features 11 Auxiliary Input Biola Setting Tuning Text Scroll Tuning Mode Selecting Russian Characters Station Preset Memory Built in Auxiliary input Setting Auto Memory Entry Power OFF Timer Preset Tuning CD Read Setting RDS features 13 Demonstration mode Setting Traffic Information Basic Operations of remote control 26 Radio Text Scroll Fe i PTY Program Type Accessories Installation Procedure 28 Program Type preset 7 3 x Changing Language for PTY Function Connecting Wires to Terminals 29 CD Audio file External disc control Installation Removing the Unit 31 features 16 Playing aad Troubleshooting Guide 32 Playing External Disc Fast Forwarding and Reversing Track File Search Disc Search Folder Search Direct Track File Search Direct Disc Search Track F
15. an AM station when the Traffic Information function is turned ON the frequency changes to an FM station During reception of traffic information the adjusted volume is automatically remembered and the next time the audio changes to traffic information the volume automatically becomes the remembered volume Receiving other traffic information stations Push the Control knob towards a a or gt gt Traffic information can be switched when it is on the Tuner Source However you cannot switch the Traffic information during reception of the Traffic bulletin switched from the source other than the Tuner Radio Text Scroll Scrolling the displayed radio text Push the Control knob toward FM for at least 2 seconds English 13 Function of KDC W4037 KDC W3537 KDC W3037 KDC W311 RDS features PTY Program Type Selecting the Program Type and searching for a station 1 Enter PTY mode Press the Control knob During PTY mode the PTY indicator is ON This function cannot be used during a traffic bulletin or AM reception 2 Select the Program Type Push the Control knob towards FM or AM Each time you push the knob the Program Type alternates between the program types shown in he table below No Program Type Display i Speech SPEECH 2 Mu
16. and for Auto Memory Entry Push the Control knob towards FM or AM 2 Open Auto Memory Entry Press the AME button for at least 2 seconds A MEMORY is displayed When 6 stations that can be received are put in the memory Auto Memory Entry closes When the lt AF Alternative Frequency gt page 23 is ON only RDS stations are put in the memory When Auto Memory Entry is done in the FM2 band the RDS stations preset in the FM1 band are not put in the memory Likewise when Auto Memory Entry is done in the FM3 band RDS stations preset in FM1 or FM2 are not put in the memory 12 English Preset Tuning Recalling the stations in the memory 1 Select the band Push the Control knob towards FM or AM 2 Recall the station Press the desired 1 6 button Function of KDC W4037 KDC W3537 KDC W3037 KDC W311 RDS features Control knob PTY indicator Tl indicator Traffic Information Changing to traffic information automatically when a traffic bulletin starts even when you are not listening to the radio Press the TI button Each time you press the button the Traffic information function turns ON and OFF When traffic information is ON Tl indicator is ON When a traffic information station is not being received the Tl indicator blinks When a traffic bulletin starts TRAFFIC is displayed and the audio changes to traffic information During reception of
17. as been loaded in the disc magazine No disc has been loaded in the disc magazine The CD is quite dirty down The CD is scra The CD is upside itched a lot The disc is unreadable Nothing has been recorded on the MD No tracks are recorded on the MD although it has a title Media was played tha t doesn t have data recorded that the unit can play The faceplate of the s connected to this uni The unit is malfunctio ave unit being has been removed ning for some reason Press the reset button on the unit If the E 77 code does not disappear consult your nearest service center Something is wrong with the disc magazine Or the unit is malfunctioning for some reason gt Check the disc magazine And then press the reset button on the unit If the E 99 code does not disappear consult your nearest service center Radio text data is being received Discs are being exchanged in the Disc changer The unit is reading the data on the disc The CD player section is not operating properly Reinsert the CD If the CD cannot be ejected or the display continues to flash even when the CD has been properly reinserted please switch off the power and consult your nearest service center PROTECT NA FILE COPY PRO DEMO The speaker wire has a short circuit or touches the chassis of the vehicle and then the protection function is activated Wire or insula
18. by mode Selecting Russian Characters Select Russian as a text display language Display Setting RUS ON Displays texts using Russian characters RUS OFF Displays texts using European characters Texts displayed using Russian characters are as follows Folder name File name Song title Artist name Album name CD text internal CD source Texts cannot distinguish upper case and lower case in Russian characters AB Br AEX 3UUK JIMHON PCTYOXUUYWUbbIb SOA In Standby mode Built in Auxiliary input Setting Set the Built in Auxiliary Input function Display Setting AUX OFF When selecting the source there s no Auxiliary Input AUX ON1 When selecting the source there s Auxiliary Input AUX ON2 When the unit is turned on by AUX source the attenuator function is activated Press ATT button to cancel the attenuator function in order to listen to the external equipment there s Auxiliary Input Setting to AUX ON2 will not output the noise which is produced when an external equipment is not connected to the AUX terminal In Standby mode Power OFF Timer Setting the timer to turn this unit s power OFF automatically when Standby mode continues Using this setting can save the vehicle s battery power Display Setting OFF Power OFF Timer function is OFF OFF 20M Turns the power OFF after 20 minutes Original set
19. ckwards between disc folders gt button Each time you press the button the song pauses or plays 0 9 buttons When in lt Direct Track File Search gt page 17 and lt Direct Disc Search gt page 17 enters the track file disc number English 27 Accessories Installation Procedure Accessories nanie 1 Pt 2 2 2 LF eet 1 Installation Procedure 1 Oo CON OO To prevent short circuits remove the key from the ignition and disconnect the terminal of the battery Make the proper input and output wire connections for each unit Connect the wire on the wiring harness Take Connector B on the wiring harness and connect it to the speaker connector in your vehicle Take Connector A on the wiring harness and connect it to vehicle he external power connector on your Connect the wiring harness connector to the unit Install the uni Reconnect the terminal of the battery Press the rese in your Car button 28 English AN f the power is not turned ON or it is ON but will be OFF immediately the speaker wire may have a short circuit or touched the chasis of the vehicle and the protection unction may have been activated Therefore the speaker wire should be checked f your car is not prepared for this special connection system consult your Kenwood dealer Only use antenna conversion adapters ISO JASO
20. d the tuner changes to the news bulletin Ifyou choose the 20MIN setting further news bulletins will not be received for 20 minutes once the first news bulletin is received The news bulletin volume is the same level that was set or lt Traffic Information gt page 13 This news bulletin function is only available if the desired station sends PTY code for news bulletin or belongs to lt Enhanced Other Network gt Network sending PTY code or news bulletin When the News Bulletin Interrupt function is ON the tuner changes to an FM station In Tuner mode Local Seek Only stations whose reception is good are searched in auto seek tuning Display Setting LO S OFF The local seek function is OFF LO S ON The local seek function is ON Function of KDC W4037 KDC W3537 KDC W3037 KDC W311 In Tuner mode Tuning Mode Sets the tuning mode Tuning mode Display Operation Auto seek AUTO 1 Automatic search for a station Preset station seek AUTO 2 Search in order of the stations in the Preset memory Manual MANUAL Normal manual tuning control Function of KDC W4037 KDC W3537 KDC W3037 KDC W311 AF Alternative Frequency When the reception is poor automatically alternate to another frequency broadcasting the same program in the same RDS network with better reception Display Setting AF ON The AF function is ON AF OFF The AF function is OFF When t
21. disc type accessories Clean from the center of the disc and move outward When removing CDs from this unit pull them out horizontally If the CD center hole or outside rim has burrs use the CD only after removing the burrs with a ballpoint pen etc CDs that cannot be used CDs that are not round cannot be used CDs with coloring on the recording surface or CDs that are dirty cannot be used This unit can only play the CDs with gise dise wise This unit may not correctly play discs which do not have the mark You cannot play a CD R or CD RW that has not been finalized For the finalization process refer to your CD R CD RW writing software and your CD R CD RW recorder instruction manual English 5 Notes About DAB Tuner control KDC W4037 KDC W3537 Refer to A group on the Instruction manual of DAB Tuner KTC 9090DAB optional accessory for the control method of DAB Tuner function However the following control methods of the function for this unit may be differed from the Instruction manual therefore refer to the following supplemental instruction lt Auto Ensemble Memory Entry gt 1 Select the preset band for Auto Ensemble Memory Entry 2 Press the AME button for at least 2 seconds Open Auto Ensemble Memory Entry After storing in the memory finishes the number of the pre set buttons and the ensemble label are displayed lt Searching by programme type and language gt
22. e unit Do Not Load 8 cm 3 in CDs in the CD slot If you try to load a 8 cm 3 in CD with its adapter into the unit the adapter might separate from the CD and damage the unit About CD players disc changers connected to this unit enwood disc changers CD players released in 1998 or later can be connected to this unit Refer to the catalog or consult your Kenwood dealer or connectable models of disc changers CD players ote that any Kenwood disc changers CD players released in 1997 or earlier and disc changers made by other makers cannot be connected to this unit Connecting unsupported disc changers CD players to his unit may result in damage Set the O N Switch to the N position for the applicable Kenwood disc changers CD players The functions you can use and the information that can be displayed may differ depending on the models being connected AN You can damage both your unit and the CD changer if you connect them incorrectly Lens Fogging When you turn on the car heater in cold weather dew or condensation may form on the lens in the CD player of the unit Called lens fogging this condensation on the lens may not allow CDs to play In such a situation remove the disc and wait for the condensation to evaporate If the unit still does not operate normally after a while consult your Kenwood dealer English 3 Notes If you experience problems during installation c
23. ecting the station 1 Select tuner source Press the SRC button Select the TUNER display 2 Select the band Push the Control knob towards FM or AM Each time you push the knob toward FM it switches between the FM1 FM2 and FM3 bands 3 Tune up or down band Push the Control knob towards ka a or gt gt During reception of stereo stations the ST indicator is ON Frequency display Preset station number Function of KDC W237 Tuning Mode Choose the tuning mode Press the AUTO button Each time you press alternates between t he button the Tuning mode he modes shown in the table below Tuning mode Display Operation Auto seek AUTO 1 Automatic search for a station Preset station seek AUTO 2 Search in order of the stations in the Preset memory Manual MANUAL Normal manual tuning control English 11 Tuner features Station Preset Memory Putting a station in the memory 1 Select the band Push the Control knob towards FM or AM 2 Select the frequency to put in the memory Push the Control knob towards lt lt or gt gt 3 Put the frequency in the memory Press the desired 1 6 button for at least 2 seconds The preset number display blinks 1 time On each band 1 station can be put in the memory on each 1 6 button Auto Memory Entry Putting stations with good reception in the memory automatically 1 Select the b
24. ffect its mechanical parts Wiping the faceplate with a hard cloth or using a volatile liquid such as thinner or alcohol may scratch the surface or erases characters Cleaning the Faceplate Terminals If the terminals on the unit or faceplate get dirty wipe them with a clean soft dry cloth Before using this unit for the first time This unit is initially set on the Demonstration mode When using this unit for the first time cancel the lt Demonstration mode Setting gt page 25 About Audio file Playable Audio file MP3 mp3 WMA wma Playable disc media CD R RW ROM e Playable disc file format ISO 9660 Level 1 2 Joliet Romeo Long file name Although the audio files are complied with the standards listed above the play maybe impossible depending on the types or conditions of media or device Playing order of the Audio file In the example of folder file tree shown below the files are played in the order from to 40 ecp O Folder L da ed Audio file DO L 4 be 1 do _ do An online manual about audio files is put on the site www ke wood com aud of en this online manual detailed information and notes which are not written in this manual are provided Make sure to read through the online manual as well Handling CDs Do not touch the recording surface of the CD Do not stick tape etc on the CD or use a CD with tape stuck on it Do not use
25. h time you turn the knob the setting alternates E between the settings shown in the table below Hlename nil i Play time amp Track number P TIME Speaker type Display Clock CLOCK OFF SP OFF For 5 amp 4 in speaker SP 5 4 In Standby Auxiliary input source For 6 amp 6x9 in speaker se nene Display For the OEM speaker SP OEM Source mane SBC NAME Clock CLOCK 4 Exit Speaker Setting mode Press the VOL knob Switching Display Changing the information displayed 1 Enter Switching Display mode Press the Control knob for at least 1 second DISP SEL is displayed 2 Select the Display item Push the Control knob towards ka a or gt gt In Tuner source KDC W237 Information Display Frequency FREQ Clock CLOCK In Tuner source Information Display Frequency MW LW FREQ Program Service name FM FREQ PS Radio text Program Service name FM R TEXT Clock CLOCK 3 Exit Switching Display mode Press the Control knob Album name cannot be displayed in WMA file If the selected display item does not have any information alternative information is displayed Function of KDC W4037 Subwoofer Output Turning the Subwoofer output ON or OFF Push the Control knob toward AM for at least 2 seconds Each time you push the knob Subwoofer output switches ON and OFF When it is ON SW ON is displayed English 9 General features Theft Deterrent Facepla
26. he AF function is ON the RDS indicator is ON When no other stations with stronger reception are available for the same program in the RDS network you may hear the incoming broadcast in bits and snatches Turn OFF the AF function in such a case Function of KDC W4037 KDC W3537 KDC W3037 KDC W311 Restricting RDS Region Region Restrict Function You can choose whether or not to restrict the RDS channels received with the AF function for a particular network to a specific region Display Setting REG ON The Region Restrict Function is ON REG OFF The Region Restrict Function is OFF If AF function is not restricted to the specified region and network the AF function sets up to search the station with good reception in the same RDS network English 23 Menu system Function of KDC W4037 KDC W3537 KDC W3037 KDC W311 Auto TP Seek When the TI function is ON and the reception is poor while listening to a traffic information station another traffic information station with better reception will be searched for automatically Display Setting ATPS ON The Auto TP Seek Function is ON ATPS OFF The Auto TP Seek Function is OFF In FM reception Monaural Reception You can reduce the noise when stereo broadcasts are received as monaural Display Setting MONO OFF The monaural reception is OFF MONO ON The monaural reception is ON Auxiliary Input Display Setting
27. he disc or Audio file folder you are listening to and searching for the song you want to hear 1 Start Scan Play Press the SCAN button TRAC SCN FILE SCN is displayed 2 Release it when the song you want to listen to is played Press the SCAN button 18 English Random Play Play all the songs on the disc or Audio file folder in random order Press the RDM button Each time you press the button Random Play turns ON or OFF When the Random mode is ON DISC RDM FOLD RDM is displayed When you push the Control knob toward gt the next random song starts Function of KDC W4037 KDC W3537 Function of disc changer Magazine Random Play Play the songs on all the discs in the disc changer in random order Press the M RDM button Each time you press the button the Magazine Random Play turns ON or OFF When the Magazine Random mode is ON MGZN RDM is displayed When you push the Control knob toward gt the next random song starts Function of Audio file Folder Select Quickly selecting the folder you want to hear 1 Enter Folder Select mode Press the F SEL button FLD SEL is displayed During Select mode the folder information is displayed as shown below Folder name display Displays the current folder name 2 Select the folder level Push the Control knob towards FM or AM With the FM of the Control knob you move 1 level down and with the AM of the Cont
28. ile Disc Folder Repeat Scan Play Random Play agazine Random Play Folder Select Text Title Scroll Specifications 34 2 English Safety precautions AWARNING To prevent injury or fire take the following precautions To prevent a short circuit never put or leave any metallic objects such as coins or metal tools inside the unit Mounting and wiring this product requires skills and experience For safety s sake leave the mounting and wiring work to professionals ACAUTION To prevent damage to the machine take the following precautions Make sure to ground the unit to a negative 12V DC power supply Do not install the unit in a spot exposed to direct sunlight or excessive heat or humidity Also avoid places with too much dust or the possibility of water splashing Do not place the faceplate and the faceplate case in areas exposed to direct sunlight excessive heat or humidity Also avoid places with too much dust or he possibility of water splashing To prevent deterioration do not touch the terminals of the unit or faceplate with your fingers Do not subject the faceplate to excessive shock as it is a piece of precision equipment e When replacing a fuse only use a new fuse with he prescribed rating Using a fuse with the wrong rating may cause your unit to malfunction Do not use your own screws Use only the screws provided If you use the wrong screws you could damage th
29. ject the CD Press the 4 button Refer to lt About Audio file gt page 5 for the Audio file by models you can play You can eject the disc for 10 minutes after switching off the engine 16 English Play time Function of KDC W4037 KDC W3537 Playing External Disc Playing discs set in the optional accessory disc player connected to this unit Press the SRC button Select the display for the disc player you want Display examples Display Disc player CD CH CD changer MD CH MD changer Pause and play Press the Control knob Each time you press the knob the audio pauses or plays Disc 10 is displayed as 0 The functions that can be used and the information that can be displayed will differ depending on the external disc players being connected Fast Forwarding and Reversing Fast Forwarding Hold down toward gt gt with the Control knob Release to resume the playback Reversing Hold down toward ka a with the Control knob Release to resume the playback There is no sound while the Audio file is being searched The accurate track time is not displayed during fast forwarding or reversing of the Audio file Track File Search Searching for a song on the disc or in the Audio file folder Push the Control knob towards ka a or gt gt Function of disc changer Audio file Disc Search Folder Search Selecting the disc set in the Disc changer or the
30. ndicator Power Turning ON the Power Press the SRC button When the power is ON the lt Security Code gt page 20 is displayed as CODE ON or CODE OFF Function of the KDC W4037 KDC W3537 Turning OFF the Power Press the SRC button for at least 1 second Selecting the Source Press the SRC button Clock display Source required Display Tuner TUNER O Cp External disc Optional accessory CD CH Auxiliary input AUX Auxiliary input Optional accessory AUX EXT Standby Illumination only mode STANDBY An equipment such as a portable audio player can be connected to the auxiliary input terminal using a commercially available mini plug 3 59 This unit automatically turns full power OFF after 20 minutes lapses in Standby mode in order to save the vehicle s battery The time until full power OFF can be set in lt Power OFF Timer gt page 25 Function of KDC W4037 KDC W3537 Use the mini plug which is stereo type and does not have any resistance Volume Increasing Volume Turn the VOL knob clockwise Decreasing Volume Turn the VOL knob counterclockwise English 7 General features Attenuator Turning the volume down quickly Press the ATT button Each time you press the button the Attenuator turns ON and OFF When the Attenuator is ON the ATT indicator blinks Audio Control 1 Select the source to adjust Press the SR
31. onize Clock gt page 22 is set as OFF 1 Select Clock Adjustment mode Push the Control knob towards FM or AM Select the CLK ADJ display 2 Enter Clock Adjust mode Press the Control knob for at least 1 second The clock display blinks 3 Adjust the hours Push the Control knob towards FM or AM Adjust the minutes Push the Control knob towards ka a or gt gt 4 Exit Clock adjustment mode Press the MENU button English 21 Menu system Function of KDC W4037 KDC W3537 KDC W3037 KDC W311 In Standby mode Synchronize Clock Synchronizing the RDS station time data and this unit s clock Display Setting SYNC ON Synchronizes the time SYNC OFF Adjust the time manually It takes 3 to 4 minutes to synchronize the clock In Standby mode DSI Disabled System Indicator A red indicator will blink on the unit after the faceplate is removed warning potential thieves Display Setting DSI ON LED flashes DSI OFF LED OFF Function of KDC W4037 In Standby mode Selectable Illumination Selecting the button illumination color as green or red Display Setting KEY RED The illumination color is red KEY GRN The illumination color is green Dimmer You can lower the brightness of the display by using the dimmer function Display Setting DIM ON The display dims DIM OFF The display doesn t dim 22 English Function of K
32. onsult your Kenwood dealer When you purchase optional accessories check with your Kenwood dealer to make sure that they work with your model and in your area The characters which can be displayed by this unit are A Z 0 9 amp lt gt The RDS feature won t work where the service is not supported by any broadcasting station The illustrations of the display and the panel appearing in this manual are examples used to explain more clearly how the controls are used Therefore what appears on the display in the illustrations may differ from what appears on the display on the actual equipment and some of the illustrations on the display may be inapplicable How to reset your unit If the unit fails to operate properly press the Reset button The unit returns to factory settings when the Reset button is pressed Press the reset button if the disc auto changer fails o operate correctly Normal operation should be restored Reset button 4 English Cleaning the Unit If the faceplate of this unit is stained wipe it with a dry soft cloth such as a silicon cloth If the faceplate is stained badly wipe the stain off with a cloth moistened with neutral cleaner then wipe it again with a clean soft dry cloth A Applying spray cleaner directly to the unit may a
33. or immediately if the battery is accidentally swallowed A Do not set the remote control in hot places such as on the dashboard 26 English ii lt gt AM DIRECT IOK QO Not Used J This button is used when Bluetooth HANDS FREE BOX is connected For more information refer to the instruction manual of Bluetooth HANDS FREE BOX Basic operations VOL buttons Adjusts the volume SRC button Each time you press the button the source alternates For the source alternating order refer to lt Selecting the Source gt page 7 ATT button Turns the volume down quickly When the button is pressed again the volume returns to the previous level Audio Control AUD button Selects the Audio item to be adjusted VOL buttons Adjusts the Audio item Refer to lt Audio Control gt page 8 for the operation method such as the procedures for Audio control and others operations In Tuner source FM AM buttons Selects the band Each time you press the FM button the band alternates between the FM1 FM2 and FM3 bands lt lt gt gt buttons Tune up or down band 0 9 buttons Press buttons 1 6 to recall preset stations gt 11 button Enters and cancels the lt PTY Program Type gt page 14 mode In Disc source lt lt gt gt buttons Going forwards and backwards between track files buttons Going forwards and ba
34. rol knob 1 level up Selecting a folder in the same level Push the Control knob towards ka a or gt With the ka a of the Control knob you move to the previous folder and with the gt i of the Control knob to the next folder Returning to the top level Press the 3 button Scrolling the folder name display Push the Control knob toward FM for at least 2 seconds 3 Decide the folder to play Press the Control knob The Folder Select mode releases and the Audio file in the folder being displayed plays Cancelling the Folder Select mode Press the F SEL button Text Title Scroll Scrolling the displayed CD text or Audio file text Push the Control knob toward FM for at least 2 seconds English 19 Menu system Control knob MENU RDS indicator Menu display Menu System Setting beep sound during operation etc functions The Menu system basic operation method is explained here The reference for the Menu items and their setting content is after this operation explanation 1 Enter Menu mode Press the MENU button for at least 1 second MENU is displayed 2 Select the menu item Push the Control knob towards FM or AM Example When you want to set the beep sound select the BEEP display 3 Set the menu item Push the Control knob towards lt lt or gt gt Example When you select BEEP each time you push the knob it alternates between BE
35. s ka a or gt gt 5 Select the Security Code numbers Push the Control knob towards FM or AM 6 Repeat steps 4 and 5 and complete the Security Code 7 Confirm the Security Code Press the Control knob for at least 3 seconds When RE ENTER is displayed CODE is also displayed 8 Do the step 4 through 7 step operation and reenter the security code APPROVED is displayed The Security Code function activates Ifyou enter a Code different from your Security Code you have to start over from step 4 Resetting the Security Code function when the audio unit is first used after removed from the battery power source or the Reset button is pressed 1 Turn the power ON 2 Do the step 4 through 7 step operation and reenter the security code APPROVED is displayed Now you can use the unit If an incorrect code is entered WAITING is displayed and the input prohibition periods shown in the table below is generated After the input prohibition time lapses CODE is displayed and you can reenter the code Number of times the incorrect code was input 1 Input prohibited time 2 5 minutes 3 1 hour 4 24 hours In Standby mode Touch Sensor Tone Setting the operation check sound beep sound ON OFF Display Setting BEEP ON Beep is heard BEEP OFF Beep canceled In Standby mode Manual Clock Adjustment You can do this adjustment when the lt Synchr
36. sic MUSIC 3 ews NEWS 4 Current Affairs AFFAIRS 5 Information INFO 6 Sport SPORT T Education EDUCATE 8 Drama DRAMA 9 Culture CULTURE 0 Science SCIENCE 1 Varied VARIED 2 Pop Music POP M 3 Rock Music ROCK M 4 Easy Listening Music EASY M 5 Light Classical LIGHT M 6 Serious Classical CLASSICS 7 Other Music OTHER M 8 Weather WEATHER 9 Finance FINANCE 20 Children s programs CHILDREN 21 Social Affairs SOCIAL 22 Religion RELIGION 23 Phone n PHONE IN 24 rave TRAVEL 25 Leisure LEISURE 26 azz Music JAZZ 27 Country Music COUNTRY 28 ational Music NATION M 29 Oldies Music OLDIES 30 Folk Music FOLK M 31 Documentary DOCUMENT 14 English Speech and Music include the Program type shown below Music No 12 17 26 30 Speech No 3 11 18 25 31 You can put the Program Type in the 1 6 button memory and for quick recall Refer to the lt Program Type preset gt page 14 You can change the display language Refer to lt Changing Language for PTY Function gt page 15 3 Search for the selected Program Type station Push the Control knob towards ka a or gt gt When you want to search for other stations push ma a or gt gt of the Control knob again When the selected Program Type is not found NO PTY is displayed Select another Program Type 4 Exit PTY mode Press the Control knob
37. st be the result of slight misoperation or miswiring Before calling service first check the following table for possible problems General H The Touch Sensor Tone doesn t sound WV The preout jack is being used ts The Touch Sensor Tone can t be output from the preout jack Tuner source oH Radio reception is poor V The car antenna is not extended VW The antenna control wire is not connected t Connect the wire correctly referring to the section on lt Connecting Wires to Terminals gt page 29 Disc source H The specified disc does not play but another one plays instead WY The specified CD is quite dirty a re Clean the CD V The disc is loaded in a different slot from that specified ts Eject the disc magazine and check the number WY The disc is severely scratched ts Try another disc instead Audio file source H The sound skips when an Audio file is being played WV The media is scratched or dirty ts Clean the media referring to the CD cleaning of seats the section on lt Handling CDs gt page 5 VW The recording condition is bad ts Record the media again or use another media The messages shown below display your systems condition EJECT NO DISC TOC ERR E 05 BLANK E 15 E 77 WAITING LOAD READING IN Blink O TRACK O PANEL No disc magazine has been loaded in the changer The disc magazine is not completely loaded No CD in the unit No disc h
38. te The faceplate of the unit can be detached and taken with you helping to deter theft Removing the Faceplate Press the Release button The faceplate unlocks allowing you to detach it A The faceplate is a precision piece of equipment and can be damaged by shocks or jolts Keep the faceplate in its faceplate case while detached Do not expose the faceplate and the faceplate case to direct sunlight or excessive heat or humidity Also avoid places with too much dust or the possibility of water splashing Reattaching the Faceplate 1 Align the projections on the unit with the grooves on the faceplate Projections SS Grooves 2 Push the faceplate in until it clicks The faceplate is locked in place allowing you to use the unit 10 English TEL Mute The audio system automatically mutes when a call comes in When a call comes in CALL is displayed The audio system pauses Listening to the audio during a call Press the SRC button The CALL display disappears and the audio system comes back ON When the call ends Hang up the phone The CALL display disappears and the audio system comes back ON To use the TEL Mute feature you need to hook up the MUTE wire to your telephone using a commercial telephone accessory Refer to lt Connecting Wires to Terminals gt page 29 Tuner features Control knob ST indicator Band display Tuning Sel
39. te the speaker cable properly and press the reset button If the PROTECT code does not disappear consult your nearest service center An Audio file is played with a format that this unit can t support een A copy protected file is played gt The Demonstration mode has been selected gt The lt Demonstration mode Setting gt page 25 is ON Turn it OFF English 33 Specifications Specifications subject to change without notice FM tuner section Frequency range 50 kHz space 87 5 MHz 108 0 MHz Usable sensitivity S N 26dB 0 7 uV 75 Q Quieting Sensitivity S N 46dB 1 6 uV 75 Q Frequency response 3 0 dB 30 Hz 15 kHz Signal to Noise ratio MONO 65 dB Selectivity DIN 400 kHz gt 80 dB Stereo separation 1 kHz 35 dB MW tuner section Frequency range 9 kHz space 531 kHz 1611 kHz Usable sensitivity S N 20dB 25 uV LW tuner section Frequency range 153 kHz 281 kHz Usable sensitivity S N 20dB 745 uV CD player section Laser diode GaAlAs Digital filter D A 8 Times Over Sampling D A Converter 1 Bit Spindle speed 500 200 rpm CLV Wow amp Flutter Below Measurable Limit Frequency response 1 dB 10 Hz 20 kHz Total harmonic distortion 1 kHz 0 01 Signal to Noise ratio 1 kHz 105 dB Dynamic range 93 dB MP3 decode Compliant with MPEG 1 2 Audio Layer 3 WMA decode Compliant with Windo
40. ting OFF 40M Turns the power OFF after 40 minutes OFF 60M Turns the power OFF after 60 minutes In Standby mode CD Read Setting When there is a problem with playing a CD with special format this setting plays the CD by force Display Setting CD READ1 Play CD and Audio file CD READ2 Play CD by force Some music CDs may not play even in the CD READ2 mode In Standby mode Demonstration mode Setting Sets the demonstration mode 1 Select the Demonstration mode Push the Control knob towards FM or AM Select the DEMO display 2 Set the Demonstration mode Press the Control knob for at least 2 seconds Each time you press the knob at least 2 seconds the Demonstration mode alternates between the settings shown in the table below Display Setting DEMO ON The Demonstration mode function is ON DEMO OFF Exit Demonstration mode Normal mode English 25 Accessory of KDC W4037 KDC W3537 Sales area other than Western European Countries Basic Operations of remote control VOL AUD FM AM g 0 9 Loading and Replacing the battery Use two AA R6 size batteries Slide the cover while pressing downwards to remove it as illustrated Insert the batteries with the and poles aligned properly following the illustration inside the case AWARNING Store unused batteries out of the reach of children Contact a doct
41. ws Media Audio 34 English Audio section Maximum output power 50Wx4 45 W x 4 KDC W237 Output power DIN 45324 B 14 4V 30Wx4 28 W x 4 KDC W237 Speaker Impedance 4 8Q Tone action Bass 100 Hz 8 dB Middle 1 kHz 8 dB Treble 10 kHz 8 dB Preout level Load during disc play KDC W4037 2000 mV 10 kQ Preout impedance during disc play KDC W4037 gt lt 6000 Auxiliary input Frequency response 1 dB 20 Hz 20 kHz Input Maximum Voltage 1200 mV Input Impedance 100 kQ General Operating voltage 11 16V allowable 14 4V Current consumption 10A Installation Size W x H x D 182 x 53x 155mm Weight 1 40 kg KENWOOD

Kenwood KDC-W3537 User's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents