Kenmore Deluxe 625.384650 User's Manual
Contents
1. In an existing sink spray attachment hole Drill a hole in the sink top Drill a hole in the countertop next to the sink 1 If drilling is needed make a 1 to 1 1 4 diameter hole for the faucet in porcelain or stainless steel Special drill bits are made for this 2 Place plumbers putty around the drilled hole to prevent water leaks around the faucet 1 to 1 1 4 diameter hole through sink or countertop FIG 3 stiano CAUTION To avoid damaging the sink consult a plumbers qualified plumber or installer for drilling procedures putty STEP 3 ASSEMBLE AND FIG 4 INSTALL FAUCET 1 Faucet FIG 4 1 Remove the large nut from the faucet threads 2 Slide the faucet stud and telephone style wire through the sink or countertop hole 3 On the underside of the sink or countertop screw the nut on the faucet threads with the wire running through the slot in the washer Tighten the nut so the faucet cannot move but do not overtighten 4 Connect tubing to push to connect fitting on bot tom of faucet stud per instructions on page 7 5 Connect the telephone style wire to the recepticle on PWA board in the manifold and route the wiring through slots in top cover and manifold assembly faucet amp spout ASSEMBLED IN MOUNTING HOLE hole in sink or countertop EE Is DI slotted washer ON nut TUBING FROM DRINKING A WATER SYSTEM INSTALLATION STEPS STEP 4 MAKE TUBING CONNECTIO2. Part Description www KenmoreWater com REPAIR SERVICES America s Repair Specialists Sears Roebuck and Co Hoffman Estates IL 60179 U S A 7227467 Rev C 05 11 01
3. applied at ini tial start up the LED indicator light will flash in a am ber green red sequence All timers and counters are reset to zero In order to reset the monitor time and gallon count feature the batteries should be removed for a mini mum of five seconds and then reinserted Batteries need to be replaced once a year at the time of filter replacement Do not mix battery types use filtered water O fo faucet only AA alkaline batteries Improper placement of batteries could damage electronics Use care when inserting batteries to align them correctly in man ifold with the proper polarity If the faucet LED indicator light does not function af ter a battery change and the batteries are known to be good and installed properly there may be a resid ual charge on the static protection device To dissi pate this charge remove the batteries for one hour GD A ll FILTER CARTRIDGE USEFUL LIFE REPLACEMENT FILTER CARTRIDGE LIFE Several variables determine how long a cartridge will last These include 1 how much water you use 2 how much sediment taste and or odor or other unwanted substance is in the water Use the following information as a guide However no matter which type of cartridge you are using you will know it is time to r
4. m i 3 4 3 8 tubing FIG 5 B collet depress to remove tubing CAUTION I I l DO NOT USE VINEGAR OR OTHER ACID BASED CLEANERS ON THIS SYSTEM THEY WILL DEGRADE SOME SYSTEM PARTS AL WAYS USE SOAP AND WATER I STEP 5 FILTER CARTRIDGE INSTALLATION Turn to page 9 and follow all steps under Filter Cartridge Replacement A taste and odor cartridge contains activated carbon a black powder After the new cartridge is installed open the filtered water faucet and allow fine harmless carbon particles to purge from the cartridge Close the faucet when you no longer see the fines in the filtered water or approximately 2 3 minutes USING THE SYSTEM The sink or countertop faucet has a hand operated knob to access drinking water Turning the knob to the left opens the faucet turning to the right shuts off the faucet FAUCET ELECTRONICS The Undersink Drinking Water Filter will monitor the total water flow of the unit and also length of time the filters have been installed The faucet base has an indicator light that flashes to inform you of the status of the filters Green Filters are good Amber Warning filters need replacing shortly Filters need replacing when water has been drawn after 168 days or 960 gallons have been used since battery change Red Filters must be replaced Will flash after 14 additional days or 80 additional gallons When the two AA batteries are first
5. 128 Sump 2 req DESCRIPTION pae 7223633 O Ring 2 req 42 38466 Filter Carbon Block 2 Pack 9006062 Screw 2 req 9041700 Hanger Washer 2 req 7234210 Paddlewheel amp O Ring Kit 7234228 Paddlewheel Cover amp Screw Kit 7234252 Rep Pwa includes screw OO CO NOIA wN 7234286 Cover Manifold 10 7226495 Faucet 11 7228536 Feed Supply Fitting 7157280 Tubing 3 8 x 20 white 7227467 Owners Manual not illustrated il A 741111012 UNDERSINK DRINKING OWNERS WATER FILTER MANDAE SYSTEM For the repair or replacement parts you need Call 7 am 7 pm 7 days a week MODEE NO 1 800 366 PART 1 800 366 7278 For in home major brand repair service dia Call 24 hours a day 7 days a week fl ai STS REPAIR SENI The model number of 1 800 4 REPAIR FEPNA SE your drinking water filter 1 800 473 7247 0 system is found on the rating decal located on the back ofthe post filter For the location of a Sears Repair Service Center in your area When requesting service Call 24 hours a day 7 days a week or ordering parts always 1 800 488 1222 provide the following in formation For information on purchasing a Sears Maintenance Agreement or to inquire Product Type about an existing Agreement Model Number Call 9 am 5 pm Monday Saturday Part Number 1 800 827 6655
6. NS 1 Allowing some slack measure and cut a length of 3 8 tubing to connect between the supply fitting and the filter system inlet FIG 1 Cut the ends of the tubing square 2 Insert tubing all the way into the supply fitting and inlet fitting Pull on the tubing to be sure that it s held firmly in the fitting 3 Repeat steps 1 and 2 to connect tubing between the filter system outlet and the adaptor on the bottom of the faucet stud FIG 1 TUBING CONNECTION all push in fitting locations This system includes push in fittings for quick tub ing connection at most locations If working with the fittings do the following Connection FIG 5 A 1 Use a sharp cutter or knife to cut the end of tubing square 2 Inspect the end about 1 of the tubing to be sure there are no nicks scratches or other rough spots If needed cut the tubing again 3 Push tubing through the collet and all the way into fitting Full engagement is 11 16 for 1 4 tubing and 3 4 for 3 8 tubing If tubing other than supplied with the system is used be sure it is of high quality exact size and roundness with a smooth surface To Disconnect Tubing FIG 5 B Push the collet in ward and hold with a finger while pulling the tubing out FIG 5 A Tubing correctly cut and connected cut tubing square collet gE end of tubing round and E smooth with no cuts nne ae aa nicks or flat spots m engagement
7. OWNER S MANUAL MODEL NO 625 384650 Caution Read and Follow All Safety Rules Installation and Operating Instructions Before First Use of This Product If you have questions when installing and using your drinking water filter system call this toll free number 1 800 426 9345 www KenmoreWater com SAVE THIS MANUAL Kenmore DELUXE DUAL STAGE DRINKING WATER SYSTEM Safety Guides Installation Operation Cartridge Replacement Repair Parts System tested and certified by NSF International to A x ANSI NSF Standard 42 and 58 for the reduction of NSF the claims specified on the performance data sheet J i Sears Roebuck and Co Hoffman Estates IL 60179 USA SAFETY GUIDES SPECIFICATIONS Y Read all steps and guides carefully before instal ling and using your undersink drinking water filter system Follow all steps exactly to correctly install Reading this manual will also help you to get all the benefits from the undersink drinking water filter system V Use the filter on a potable safe to drink home COLD water supply only The filter cartridge will not purify water or make it safe to drink DO NOT use on HOT water 100 F max Do not use with water that is microbiologically unsafe or of un known quality without adequate disinfection be fore or after the system This sy
8. SINK DRINKING WATER FILTER SYSTEM TO THE NEAREST SEARS STORE THROUGHOUT THE UNITED STATES This warranty gives you specific legal rights and you may have other rights which vary from state to state Sears Roebuck and Co DEPT 817 WA Hoffman Estates IL 60179 TABLE OF CONTENTS Parts of the System Typical Installation Drawing Tools and Materials Needed r iran p ee de ye ee Lie 4 Drinking Water Filter System Installation 5 7 Installing Supply Fitting 0 2 eee 5 Installing Faucets a 5 6 Making Tubing Connections LL LL 7 Using the Filtered Water System 8 Filter Cartridge Life Replacement LL0 8 9 Re pain Parts aiuto iL iO tellececitetaly 10 11 Locate the water filter housing on the cold water supply pipe under the kitchen or bathroom sink to filter the cold drinking water Refer to the following drawing FILTERING WATER TO ONE FAUCET filtered water faucet kitchen sink DRINKING WATER FILTER SYSTEM COLD n LTERI FILTERI PARTS OF THE SYSTEM filter system assembly including mounting brack et and screws v water supply fitting filtered water faucet for sink or countertop mount ing 3 8 tubing to make all needed connections MATERIALS AND TOOLS NEEDED plumbers putty Phillips screwdrivers pliers and adjustable jaw wrench tubing cutter pipe joint compound or Teflon tape electric drill an
9. d 1 drill bit if mounting hole is needed for the faucet see page 6 CAUTION To avoid damaging the sink consult a qualified plumber or installer for drilling procedures in porcelain or stainless steel TYPICAL UNDERSINK INSTALLATION FIG 1 filtered water faucet 3 9 16 hanger washer 2 screw 2 9 15 1 2 min up from floor Monitor supply fitting Cable WATER ia IN shutoff valve Note To change the fil ter cartridge you must turn offthe water and re lease pressure by open i ing the faucet A nearby i shutoff valve is conve nient Most sinks al tubing ready have shutoff valves on the supply pipes Filter I I Filter II i Note Be sure to allow a minimum space of 1 1 2 under the system for removing the sumps to change the cartridges INSTALLATION STEPS STEP 1 COLD WATER SUPPLY FITTING Check and comply with local plumbing codes as you plan then install a cold feed supply water fitting The fitting must provide a leak tight connection to the water filter 3 8 tubing A typical connection using the in cluded water supply fitting is shown in FIG 2 A An optional connection using standard plumbing fittings not included is shown in B A WATER SUPPLY FITTING 1 Close the house main water shutoff valve and open faucets to drain water from the sink cold water pipe 2 Remove nut that connects the cold water faucet to cold water p
10. eplace it when you first no tice the return of the unwanted substance in your water Kenmore system model 625 384650 with replace ment elements 42 38466 has been tested and certi fied by NSF International for the reduction of chlo rine lead asbestos cysts VOC s and MTBE The rated capacity for this system is 1040 gallons FILTER CARTRIDGE REPLACEMENT CAUTION Never remove sumps with water pres sure in the filter system 1 Close the water supply shut off valve FIG 1 page 4 to the filter Open the filtered water faucet cartridge eae o ring seal TURN SUMP CLOCKWISE TO REMOVE Sa Filter I 3 Be sure the inside of the sump is clean Use hot soapy water and rinse thoroughly 4 Remove the wrapper from the new filter cartridge and insert the filter cartridge in the sump Be sure the two o rings are towards the filter head Note If you are installing two different types of filter cartridges be sure to install in filters I and II as the guideline on page 3 shows 5 Lightly lubricate the o ring seal in the sump with silicone grease or Vaseline Be sure it is fully seated in its groove 6 Hold the sump up to the filter head aligning the protrusion on the cartridge with the center hole in the bottom of the head Note If the sump will not tighten up to the head you may have the cartridge in upside down Take the car tridge out and check for correct orientation 7 Turn counterclockwise the su
11. lumbing 3 Use pipe joint compound or Teflon tape on cold water faucet stud threads and on the male threads of the water supply fitting that connect to the cold water pipe 4 Thread water supply fitting onto pipe and reconnect nut to bottom of fitting FIG 2 A WATER SUPPLY CONNECTION using included water supply fitting cold water faucet stud water supply fitting Kay 4 3 8 tubing to Water Filter inlet 2 lt lt cold water pipe TH a i b CD ia lt gt cold water shutoff B OPTIONAL PIPE FITTINGS compression type shown Note Be sure to turn off the water supply and open a low faucet to drain the pipe Complying with plumbing codes install a fitting on the cold water pipe to adapt 3 8 OD tubing A typi cal connection is shown in figure 2B If threaded fit tings are used be sure to use pipe joint compound or Teflon tape on outside threads B WATER SUPPLY TYPICAL CONNECTION using compression fitting parts not included cold water shutoff 3 8 compression 7 fitting insert amp ferrule 3 8 tubing to Water Filter inlet INSTALLATION STEPS STEP 2 MAKE HOLE FOR FILTERED WATER FAUCET Select one of the following places toinstall the faucet Be sure there s room underneath so you can make the needed connections
12. mp onto the filter head 1 4 turn 8 Repeat steps 2 through 7 at the other filter to relieve pressure in the system 2 Turn the sump off of the filter head to the left or clockwise 1 4 turn Be careful the sump is full of wa ter Do not lose the large o ring seal head sump TURN SUMP COUNTER CLOCKWISE TO TIGHTEN Filter II 9 Open the filtered water faucet Then slowly open the water supply valve and allow the filter housing to fill 10 Close the filtered water faucet Check for leaks be tween the sump and the head 11 Remove and replace batteries to reset counter and timer Note If leaking turn off the water supply and open the filtered water faucet to depressurize the filter Then disassemble the filter and check the o ring for cuts flat spots etc and sealing surfaces for foreign material Clean the o ring and lubricate with silicone grease or Vaseline Carefully press the o ring into the groove in the sump 12 Taste and Odor Cartridges A taste and odor car tridge contains activated carbon a black powder When new open the filtered water faucet and allow fine harmless carbon particles to purge from the car tridge Close the faucet when you no longer see the fines in the filtered water or approximately 2 3 minutes REPAIR PARTS Kenmore Deluxe Dual Stage Drinking Water System Model No 625 384650 10 REPAIR PARTS LIST KEY PART NO NUMBER 7221
13. stem is certified for cyst reduction and may be used on disinfected wa ters that may contain filterable cysts VY Check with your local public works department for plumbing and sanitation codes You must fol Min Max Supply Water Pressure Min Max Supply Water Temperature Inlet Outlet Rated Service Flow low their guides as you install the system Follow your local codes if they differ with guides in this manual In Massachusetts plumbing codes of Massachusetts shall be adhered to Consult with your licensed plumber Y The undersink drinking water filter system works on water pressures of 30 psi minimum to 100 psi maximum If your house water pressure is over the maximum install a pressure reducing valve in the water supply pipe to the filter system V Read the other limits pH hardness etc in the specifications and be sure your water supply con forms W Protect the undersink drinking water filter sys tem and piping from freezing Water freezing in the housing will break it 30 100 psi 40 100 F 3 8 fittings and tubing included 0 6 gpm at 60 psi WARRANTY FULL ONE YEAR WARRANTY ON UNDERSINK DRINKING WATER FILTER SYSTEM For one year from the date of purchase Sears will replace this Undersink Drinking Water Filter System except filter cartridges which are purchased separately free of charge if defective in material or workmanship WARRANTY IS AVAILABLE BY SIMPLY RETURNING THE UNDER
Download Pdf Manuals
Related Search