Kenmore Air Conditioner 408.72012 User's Manual
Contents
1. e Cleaning Wash the air filter by immersing it in lukewarm water and a mild detergent Rinse the filter and wait for it to dry before sliding it back into the filter cover C CLEANING THE EXTERIOR Moisten a soft cloth with mild detergent and water to wipe the unit clean Be sure to use a soaking wet cloth D DRAINAGE EXTENDED PERIOD OF NON USE If the air conditioner will not be used for a long period of time remove the bottom rubber plug from the lower drain outlet shown below attach the drain hose and completely drain the unit of water YYYYYYYYY YYYY STORAGE e Follow cleaning instructions A D e Remove the exhaust hose and window kit and repack the unit in its original shipping box Store unit upright in a dry place where the temperature will remain above 35 F e IMPORTANT Always store and transport the unit so as to maintain the compressor in a upright orientation TECHNICAL SPECIFICATIONS MODEL 408 72012 VOLTAGE 120V 60Hz AMPERAGE COOLING HEATING POWER CONSUMPTION COOLING HEATING 12 Amps 10 5 Amps 1400W 1200W COOLING CAPACITY 12 0002. ACCESSORIES On initial unit setup check that all the accessories listed below are included Exhaust hose Drain hose for continuous drainage Remote sensor kit used only in out of room cooling mode 2 AAA batteries Remote control 16 mm inner diameter Window kit 3 pcs INSTALLATION Prior to installing the unit check for the following 1 To avoid damage place the unit in an upright position for at least 12 hours before initial operation This ensures all lubricating oil has settled to the bottom of the compressor avoiding damage to other internal parts Lift the exhaust hose holder 1 from the unit to expose the exhaust hose and accessories Remove the accessories from the hose and set aside Turn the hose in the direction of arrow 2 to completely remove the hose from the unit Return the exhaust hose holder to the unit The hose has a window connection end and a unit connection end Expand the unit connection end and insert it into the exhaust hose holder Turn the hose several turns in the direction of arrow 3 until it is securely attached in the holder 4 Plug the unit into a 120V 60Hz grounded electrical outlet DO NOT USE A REGULAR EXTENSION CORD If it is necessary to use an extension cord with this unit use an approved air conditioner extension cord only 9 INSTALLATION LOCATION OF THE PORTABL
3. a domicilio y para ordenar piezas 1 800 LE FOYER 1 888 SU HOGAR 1 800 533 6937 1 888 784 6427 www sears ca www sears com SCdIS Registered Trademark Trademark of KCD IP LLC in the United States or Sears Brands LLC in other countries Marca Registrada Marca de Fabrica de KCD IP LLC en Estados Unidos o Sears Brands LLC in otros paises MC Marque de commerce MP Marque d pos e de Sears Brands LLC TABLE OF CONTENTS Before Using Your New Air Conditioner seeecceecees 2 Important Safeguards 3 5 Kemore Air Conditioner Warranty cccccccccccccccccscsseeees 6 Master Protection Agreement 7 Unpacking Instructions 8 Air Conditioner Parts seeeees 8 Accessories 2 2 ee ecesccceccccccccees 9 Installation cccccccsssseeceees 9 10 Safety Plug csescicnsiacseseetandeserees 11 Control Panel ceeeeeees 11 13 Remote Control eeeeee 13 14 Operating Instructions 15 18 Cleaning amp Maintenance 18 19 Siro kele lt AEE E 20 Technical Specifications 20 Troubleshooting seeeeee 21 22 NGI SS lt nnsoscccsnvertcsniavtenscecones 23 BEFORE USING YOUR NEW AIR CONDITIONER READ THIS USE amp CARE GUIDE CAREFULLY AND THOROUGHLY BEFORE INSTALLING AND OPERATING YOUR AIR CONDITIONER RETAIN THIS USE amp CARE GUIDE FOR FUTURE REFERENCE IMPORTANT SAFEGUARDS To prevent injury to
4. Max 50 in Ll a 127er Vertical Window aren Horizontal Window 10 SAFETY PLUG This product is equipped with an LCDI Leakage Current Detection and Interruption safety plug If power shuts off unplug from the electrical outlet and make sure the cord is undamaged If the cord is damaged return the unit to a Sears Service Center for repair before using it again TO TEST THE SAFETY PLUG 1 Connect the power plug to an electrical outlet 2 The power plug has two buttons located on the top One button is marked TEST and the other is marked RESET Press the TEST button you will hear a click as the RESET button pops out 3 Press the RESET button you will hear a click as the button engages 4 The power supply cord is now energized and supplying electricity to the air conditioner it is indicated by a light on the plug head Under no circumstances should this device be used to turn the unit on or off e The RESET button must always be pushed in engaged for correct operation e The power supply cord must be replaced if it fails to reset when the TEST button is pushed in CONTROL PANEL 1 POWER 1 Press this button to switch the unit on or off 2 MODE Press this button to select between Cooling 3 Heating 308 or Dehumidifying E mode NOTE To change display between F and C press the MODE button for 10 seconds with the power off and unit 3 plugged in Sta
5. on warm days for ae 1 AO maximum effect This unit has a self evaporation system to eliminate water isan that condenses in the unit during cooling there is no water tank to empty eeping The drainage hose MUST NOT be connected for IN ROOM air conditioning mode Please make sure that the water outlet is closed with the rubber cap imer 58 88 ON OFF installed during operation D Etc NOTE The functions al LNF e cel of the remote control buttons are the same as described in the Control Panel section aD AUTO Automatic v Air Flow Speed Y Ns Medium Speed MED y Low Speed D gt av gt a 2 e Connect the exhaust hose and the adjustable air vent to the unit as displayed in the illustration The hose must be connected to the side with ne O e The remote control must be within 16 feet 5 meters of the receiver on the main the warm air icon 9 The warm air emitted from unit must exit the room unit Reception is confirmed by a beep from the main unit through the exhaust hose e The remote control will not operate if curtains doors or other material block the e Use the MODE button to set the unit function to COOLING Adjust the set signal from the remote control to the receiver temperature using the TEMP up or down buttons The cooling temperature e Prevent any liquid from falling into the remote control For proper remote co
6. on your product Unlimited service calls and nationwide service as often as you want us whenever you want us No lemon guarantee replacement of your covered product if four or more product failures occur within twelve months Product replacement if your covered product can t be fixed Annual Preventive Maintenance Check at your request no extra charge Fast help by phone we call it Rapid Resolution phone support frm a Sears representative on all products Think of us as a talking owner s manual Power surge protection against electrical damage due to power fluctuations 250 Food Loss Protection annually for any food spoilage that is the result of mechanical failure of any covered refrigerator or freezer Rental reimbursement if repair of your covered product takes longer than promised 10 discount off the regular price of any non covered repair service and related installed parts K KA NN ANAN AR AW Once you purchase the Agreement a simple phone call is all that it takes for you to schedule service You may call anytime day or night or schedule a service appointment online The Master Protection Agreement is a risk free purchase If you cancel for any reason during the product warranty we will provide a full refund Or a prorated refund anytime after the product warranty period expires Purchase your Master Protection Agreement today Some limitations and exclusions apply For prices and additional info
7. the lower drain outlet for effective cooling and additional moisture removal Direct the end of the hose away from the unit If the unit is working in conditions of high humidity it may display an E4 error operation you must install the remote receiver into the window kit code See Troubleshooting section 1 Punch out the circular plug from the window kit to create the remote receiver hole Keep the plug for possible later use 2 Insert the receiver through the hole from the back of the window kit piece The receiver must face into the room being cooled and be positioned higher than the main unit 3 Remove the rubber cover from the remote receiver jack found near the top 0 front of the unit Keep the cover for later use 4 Attach the end of the receiver cable to the jack on the main unit Arrange the wire so it will not get damaged stepped on or pinched When using the remote to control the unit point the remote at the receiver in the window kit Reception is confirmed by a green LED flash in the receiver DO NOT COVER OR BLOCK THIS REMOTE RECEIVER IT ALSO CONTAINS e For out of room operation position the unit on a flat solid surface in an area THE ROOM TEMPERATURE SENSOR Use the MODE button to set the unit protected from rain and sun exposure such as a sunroom veranda or hallway function to COOLING Adjust the set temperature using the TE
8. BTU h HEATING CAPACITY 12 000BTU h DEHUMIDIFYING CAPACITY 30 C RH80 126 8 Pints Day 60 Liters Day NOISE LEVEL Indoor use 53 dB A AIR CIRCULATION m3 h 205 a te at high REFRIGERANT R410A REMOTE CONTROL INCLUDED TIMER 0 24h DIMENSIONS WxDxH ae ae ey 55cm x 30cm x 76cm NET WEIGHT 65 Ibs 29 5 kg TROUBLESHOOTING If your air conditioner fails to operate please follow these procedures prior to contacting customer service DO NOT ATTEMPT TO OPEN OR REPAIR THE AIR CONDITIONER YOURSELF DOING SO WILL VOID THE WARRANTY AND CAUSE DAMAGE OR PERSONAL INJURY PROBLEM POSSIBLE CAUSE SOLUTION Can turn the unit on immediately after unpacking it Unit does not start when pressing Room temperature is higher power button than the set temperature heating mode e Room temperature is lower than the set temperature cooling mode The air conditioner does not come on No electricity It is not plugged into the outlet The internal safety device has tripped The safety device on the plug has tripped There are bends or kinks in the air exhaust hose The air conditioner works for only a short time Something is preventing the air from being discharged Room is not cool enough Windows doors in room are open There are heat sources nearby Exhaust hose is not connected or is blocked Temperature setting is too high Air filter blocked by dust The compressor control prevents the unit from being re
9. E AIR CONDITIONER 1 Select a location near a window and electrical outlet 2 Position the unit in a flat spacious location with a minimum of one foot of clearance 30 cm between the air outlets and any wall or pieces of furniture 3 If placing the unit outside of the room to be cooled position it on a flat solid surface preferably in a space with overhead shielding from rain and the direct rays of the sun Do not operate the unit in extremely moist areas such as a sauna WINDOW KIT INSTALLATION The Window Kit included contains three sliding pieces and can be adjusted to fit most standard vertical and horizontal windows see Figs 1 amp la For very wide windows use all three pieces For very narrow windows you may have to cut down the end of the piece with the hose attachment hole Do not cut into the hole EXHAUST HOSE CONNECTION The exhaust hose must be attached to the appropriate side of the unit given the desired application either cooling or heating see Operating Instructions When changing applications switch the adjustable air vent and exhaust hose holder hose can remain attached to the opposite sides of the unit Fig 1 Fig la aw in Sails ye lt gt LO 9 Window kit Window kit Min 19 in Min 19 in 48 cm 48 cm Max 50 in Ll
10. MP up or Do not operate the unit in extremely moist areas such as a sauna down buttons e The color of the unit can fade slightly due to sunlight HEATING MODE IN ROOM OPERATION ONLY e This unit is equipped with a thermal overload protector This protects the The heating function of the unit must not be operated if the room temperature unit from overheating in extreme ambient conditions is less than 57 F 15 C e Place the unit so that the air inlet is not blocked by furniture or curtains Switch the adjustable air vent and exhaust hose holder hose can remain since this can negatively affect unit performance attached to the opposite sides of the unit See Figures 1 3 The exhaust hose must be attached to the side with the Cooling icon 3 Place the unit in the shade if possible and in a cool place in order to increase efficiency and to avoid overheating If the unit is operated in extremely high ambient temperatures the unit may shut down automatically If the unit repeatedly shuts down move the unit to a cooler location out of direct sunlight The cold air emitted from unit must exit the room through the exhaust hose connected to the window kit Use the MODE button to set the unit function to HEATING Adjust the set temperature using the TEMP up or down buttons 16 17 OPERATING INSTRUCTIONS DEHUMIDIFY MODE Humidity is extracted from the air collected in the
11. Use amp Care Guide Manual de Uso y Cuidado English Espafiol Kenmore Portable Air Conditioner Dehumidifier amp Heater with Remote Control Aire Acondicionado Port til Deshumidificador y Calentador con Control Remoto Model Modelo 408 72012 P N 620209 0Y 6 A Sears Brands Management Corporation Hoffman Estates IL 60179 U S A www kenmore com www sears com Get it fixed at your home or ours Your Home For troubleshooting product manuals and expert advice managemylife www managemylife com For repair in your home of all major brand appliances lawn and garden equipment or heating and cooling systems no matter who made it no matter who sold it For the replacement parts accessories and owner s manuals that you need to do it yourself For Sears professional installation of home appliances and items like garage door openers and water heaters 1 800 4 MY HOM E Call anytime day or night 1 800 469 4663 U S A and Canada www sears com Wwww sears ca Our Home For repair of carry in items like vacuums lawn equipment and electronics call anytime for the location of the nearest Sears Parts amp Repair Service Center 1 800 488 1222 U S A 1 800 469 4663 Canada www sears com www sears ca To purchase a protection agreement on a product serviced by Sears 1 800 827 6655 USA 1 800 361 6665 Canada Para pedir servicio de reparaci n Au Canada pour service en francais
12. an will run at full speed e Ifthe set temperature is less than 9 F 4 C different than room temperature the fan will run at medium speed e When the set temperature is reached the fan will run at low speed When the temperature becomes more than 9 F 4 C different than room temperature the fan will change to medium speed 7 TIMER GS Programmable timer button for delayed start up or delayed shutdown How to program a delayed start up This function is used to set the number of hours delay before the appliance comes on Proceed as follows e With the power ON select the desired Mode of operation Cool Heat or Dehumidify e Turn the power OFF e Press the TIMER button OO will blink in the display While the display is blinking use the up and down buttons to set the number of hours delay before the unit begins operation e Wait a few seconds for the display to show the set temperature Use the up and down buttons to adjust the set temperature if desired e After the set number of hours has expired the unit starts automatically NOTE If you press the POWER button before the set delay time has expired the delay setting will cancel and the unit will immediately turn ON 12 CONTROL PANEL How to program a delayed shutdown This function is used to set the number of hours delay before the appliance shuts off Proceed as follows e With the power ON select the desired Mode of operation Cool Heat or Dehumi
13. d slide it out from the filter cover as shown below
14. dify e Press the TIMER button 00 will blink in the display While the display is blinking use the up and down buttons to set the desired number of hours until shutdown e Wait a few seconds for the display to show the set temperature Use the up and down buttons to adjust the set temperature if desired e After the set number of hours has expired the unit shuts down automatically NOTE If you press the POWER button before the set shutdown time has expired the unit will shut down immediately 72 8 SLEEP Q The Sleep mode is ideal for nighttime operation as it automatically reduces the fan speed and minimizes the compressor running for the quietest operation While the unit is ON press the SLEEP mode button The unit will switch to low fan speed In COOLING mode the temperature setting automatically increases by 2 F 1 C each hour for the first two hours of operation As a result the Sleep function provides most cooling when you first go to bed The two setting increases while you are sleeping compensate for the typical decrease in ambient temperature as the night progresses If the ambient temperature becomes 2 F 1 C cooler than the temperature setting the compressor will turn off The compressor turns back on when the ambient temperature becomes 2 F 1 C warmer than the ambient temperature In HEATING mode the temperature setting is automatically DECREASED like above and the compressor turns off if th
15. e ambient temperature becomes 2 F 1 C BELOW the setting If desired the fan speed can be manually changed while in SLEEP mode SLEEP mode cannot be activated while the unit is in DEHUMIDIFY mode REMOTE CONTROL INSERTING BATTERIES This remote control uses two AAA batteries e Remove the back cover of the remote control e Insert two AAA 1 5V batteries making sure they are in the correct position see instructions inside battery compartment e Replace the cover DO NOT mix old and new batteries DO NOT mix together Alkaline Standard Carbon Zinc or Rechargable Nickel Cadmium batteries Dispose of batteries properly DO NOT leave batteries in the remote if it will not be used for longer than 2 months 13 REMOTE CONTROL OPERATING INSTRUCTIONS USING THE REMOTE NOTE After switching the unit on the ventilator fan operates but the TOP VIEW compressor only starts after the mode indicator has flashed for 3 minutes Cool air will start to blow once the compressor starts but it may take up iraneminice __f lt o gt to another 5 minutes to feel the cooling effect in the room This is done as a protection mechanism to prolong compressor life Further information is available in the Troubleshooting section Cooling FRONT VIEW AIR CONDITIONING MODE IN ROOM OPERATION The unit stands in the room to be cooled Heating Dehumidifying oo We recommend starting your unit early in the morning
16. e for incidental or consequential damages Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages or limitation on the duration of implied warranties of merchantability or fitness so these exclusions or limitations may not apply to you This warranty applies only while this appliance is used in the United States or Canada This warranty gives you specific legal rights and you may also have other rights which vary from state to state Sears Roebuck and Co Hoffman Estates IL 60179 Sears Canada Inc Toronto Ontario Canada M5B 2C3 MASTER PROTECTION AGREEMENT Master Protection Agreements Congratulations on making a smart purchase Your new Kenmore product is designed and manufactured for years of dependable operation But like all products it may require preventive maintenance or repair from time to time That s when having a Master Protection Agreement can save you money and aggravation The Master Protection Agreement also helps extend the life of your new product Here s what the Agreement includes M Parts and labor not just for reparing defects but to help keep products operating properly under normal use Our coverage goes well beyond the product warranty No deductibles no functional failure excluded from coverage real protection Expert service by a force of more than 10 000 authorized Sears service technicians which means someone you can trust will be working
17. he product turn off the power switch of the main body of the appliance Being exposed to direct airflow for an extended period of time could be hazardous to your health IMPORTANT SAFEGUARDS Do not use this air conditioner for refrigeration purposes e g preserving precision devices food pets plants and art objects Due to the possibility of oxygen deficiency within the room ventilate the room when used together with stoves or other heating devices The air conditioner is a consumer comfort appliance not a precision climate control system Always insert the filter securely Never operate without a filter Do not drink water drained from air conditioner It contains contaminants that may make you sick Do not use this unit in conditions where the temperature may fall below 50 F 10 C Failure to do so can cause severe damage to the unit KENMORE PORTABLE AIR CONDITIONER WARRANTY Kenmore Limited Warranty When this product is installed operated and maintained according to all supplied instructions the following warranty coverage applies To arrange for warranty service call 1 800 4 MY HOME For five years from the date of purchase this product will be replaced free of charge if the sealed refrigerant system fails due to defects in material or workmanship e For one year from the date of purchase this product will be repaired free of charge for defects in material or workmanship to all components other than the sea
18. led refrigerant system All warranty coverage applies for only 90 days from the date of purchase if this product is ever used for other than private family purposes This warranty covers only defects in material and workmanship Sears will NOT pay for 1 Expendable items that can wear out from normal use including but not limited to filters belts light bulbs and bags A service technician to instruct the user in correct product installation operation or maintenance A service technician to clean or maintain this product Damage to or failure of this product if it is not installed operated or maintained according to the all instructions supplied with the product Damage to or failure of this product resulting from accident abuse misuse or use for other than its intended purpose 6 Damage to or failure of this product caused by the use of detergents cleaners chemicals or utensils other than those recommended in all instructions supplied with the product 7 Damage to or failure of parts or systems resulting from unauthorized modifications made to this product N ao or Disclaimer of implied warranties limitation of remedies Customer s sole and exclusive remedy under this limited warranty shall be product repair as provided herein Implied warranties including warranties of merchantability or fitness for a particular purpose are limited to one year or the shortest period allowed by law Sears shall not be liabl
19. n the compressor in a proper condition Prior to installation allow air conditioner to stand upright for 12 hours Only operate the unit on an even horizontal surface to ensure no water leaks This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety Children should be supervised to ensure that they do not play with the appliance Do not insert the power plug into a wall outlet if either is loose or damaged It may cause fire and electric shock Unplug the unit if strange sounds odors or smoke come from it Hold the plug by the head when unplugging the unit Do not pull on the cord Unplug the air conditioner if it will not be used for a long period to prevent accidental startup and the possibility of injury Do not place heavy objects on the power cord and take care so that the cord will not be damaged Clean the air filters regularly A contaminated air filter reduces capacity Use a soft cloth to clean Do not use wax thinners or a strong detergent The appearance of the air conditioner may deteriorate change color or develop surface flaws Do not use water to clean inside the air conditioner Exposure to water can destroy the insulation leading to possible electric shock If water enters t
20. ndby Mode You will 6 hear a beep when the change occurs 8 3 TEMP SN 4 Pressing this button in cooling mode increases the desired room temperature setting by 1 F 1 C up to a maximum setting of 86 F 30 C e Pressing this button in heating mode increases the desired room temperature setting by 1 F 1 C up to a maximum setting of 77 F 25 C CONTROL PANEL 4 TEMP Z e Pressing this button in cooling mode decreases the desired room temperature setting by 1 F 1 C down to a minimum setting of 63 F 17 C e Pressing this button in heating mode decreases the desired room temperature setting by 1 F 1 C down to a minimum setting of 59 F 15 C 5 LED DISPLAY The display shows the current temperature setting By pressing the fN or Nf buttons the temperature setting can be changed When pressing the timer button the number of hours is shown until delayed start up or delayed shutdown After each setting the display returns to showing the current temperature setting In the dehumidifying mode dh is shown on the display Error codes are also shown in the display See Troubleshooting section for Error code definitions 6 SPEED SH Pressing this button sets the ventilator fan speed to eS low i medium E S high or 4N automatic When AL is selected e f the set temperature is more than 16 2 F 9 C different than room temperature the f
21. ntrol can be set from 65 F to 90 F 17 C to 32 C functioning do not expose the window kit receiver to direct sunlight or heat e f other appliances react to the remote control move them out of the way e When using the out of room air conditioning mode point the remote control to the receiver in the window kit Reception is confirmed by an LED flash in the receiver e Do not store the remote control where temperatures will be above 140 F 60 C or below 23 F 5 C e IMPORTANT If you change the temperature scale F or C on the main unit control panel you must also change the scale to be the same on the remote control If not the main unit scale will revert to that of the remote when you use the remote control Hold the Mode button on the remote control for 10 seconds to change the temperature scale 14 15 OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS REMOTE RECEIVER INSTALLATION AIR CONDITIONING MODE OUT OF ROOM OPERATION The unit is outside the room to be cooled such as an adjacent room or hallway or outdoors beneath a porch or window awning or the overhanging eaves of a roof Connect the air hose and the adjustable air vent to the unit as displayed in the illustration hose must be connected to the side with the COOL icon 3 If the unit is placed out of room during high humidity periods connect the supplied drainage hose to
22. rmation in the U S A call 1 800 827 6655 Coverage in Canada varies on some items For full details call Sears Canada at 1 800 361 6665 Sears Installation Service For Sears professional installation of home appliances garage door openers water heaters and other home items in the U S A or Canada call 1 800 4 MY HOME UNPACKING INSTRUCTIONS 1 Place the unit in the correct upright position before unpacking 2 Cut the two packing straps 3 Slide the carton in an upward motion and it will release from the base We recommend that you retain the packaging for offseason storage 4 Grip the unit by the recessed carry handles on each side and carefully lift unit until it slides free from foam base SFA C o AIR CONDITIONER PARTS Remove the air conditioner from the packing carton It is recommended to keep the carton and packing material for storage or transportation of the unit 2 1 3 14 9 10 11 12 Front of Unit Fig 1 ONOMAWN gt Control Panel Remote receiver Adjustable air vent Hose joint Exhaust hose Upper drain outlet Carry handles Remote receiver jack Rear of Unit Fig 2 9 10 11 12 13 14 Cool air inlet Cool air filter Warm air inlet Warm air filter Lower drain outlet Exhaust hose holder
23. started until three minutes have elapsed since it was last turned off Noise or vibrations e The floor is not level or the unit is on an incline Gurgling sound The air conditioner does not operate for about three minutes after restarting it e The sound comes from the flowing of refrigerant inside the air conditioner e No The unit must be placed upright for at least 12 hours after every transport Otherwise the compressor may be damaged Lower the set temperature Raise the set temperature Check house circuit breaker panel for tripped switch Plug into outlet Wait 30 minutes if problem persists call 1 800 469 4663 to arrange for product inspection and repair Reset the safety plug Position the air hose correctly keeping it as short and free of curves as possiuble to avoid bottlenecks Check and remove any obstacles obstructing air discharge Close all windows doors Remove heat source if possible Connect the exhaust hose and make sure it can function properly Decrease the set temperature Clean the air filter Wait This delay is part of normal operation e Place the unit on a flat level surface e This is normal TROUBLESHOOTING NOTES Unit emits odor during operation First use of unit or after e Odor development can arise upon pba of unit in dusty first use and after a long period of non use by storing in unsuitable areas e g dusty areas Run the unit for 2 a day The smell will dissipa
24. te after awhile In the case of intense odor development air the room Compressor does not immediately Normal operation After pressing Power button ON activate when power button is the compressor will not start for 3 pressed ON minutes Conditioned air will start to blow once the compressor starts but it may take up to another 5 minutes to feel the cooling or warming effect in the room The unit deactivates Normal operation Upon reaching the set temperature the unit switches off automatically Check temperature setting The unit does not cool Room temperature is high Air conditioners operate more satisfactorily when unit is first turned ON effectively if a cooler room temperature is maintained To adequately cool the air in a very warm room requires much more time and energy Unit is located outdoors Move unit indoors and outside air temperature is very high Unit will only provide air that is approximately 20 cooler than outside air ERROR CODES CODES e Room temperature outside T the error code continues to the usable operating range appear call 1 800 469 4663 to arrange for product inspection and repair e Temperature of the If the error code continues to refrigerant lines is too high appear call 1 800 469 4663 to or low arrange for product inspection and repair e Water tank full If the water tank is full the warning sign E4 appears in the display To restart operation of the unit please remove
25. the outlet without making the appropriate wiring changes will create an unsafe condition that could result in fire or electric shock Refer all such work to a licensed and qualified electrician e WARNING This appliance must be properly grounded The power cord of this appliance is equipped with a three prong LCDI Leakage Current Detection and Interruption plug To minimize the risk of electric shock use the plug with a standard three slot grounding wall power outlet If power outlet does not include a grounding slot have a qualified electrician replace the outlet before you use your room air conditioner Do not cut or remove the grounding prong from the power plug If you have doubt whether the air conditioner is properly grounded have the wall receptacle and circuit checked by a qualified electrician e Do not disassemble or modify this appliance Doing so may cause failure and electric shock IMPORTANT SAFEGUARDS TEMPORARY USE OF AN EXTENSION CORD We strongly discourage the use of an extension cord due to potential safety hazards For temporary situations use only CSA and UL certified 3 prong grounded extension cords designed and approved specifically for air conditioners To prevent injury from handling sharp objects do not touch the metal parts of the unit when removing the filter Do not block the air inlet or air outlet It may cause failure of the appliance Always store and transport the air conditioner upright to maintai
26. the plug of the lower drain outlet to allow the water to drain out Please use an appropriate collection pan When the water has been completely removed start the unit again The unit can now be used as usual e De icing mode This procedure is completely normal and protects the system from icing and failure The unit starts automatically after approx 15 minutes depending on the function setting This procedure repeats itself regularly 22 23
27. the user or other people and property damage the following instructions must be followed e Use this appliance only as described in this Use amp Care Guide As with any electrical appliance the instructions aim to cover as many eventualities as possible Caution and common sense should be used when operating and installing this air conditioner e This appliance has been manufactured to cool heat and dehumidify domestic environments and should not be used for other purposes e The appliance should not be installed where the atmosphere may contain combustible gases oil or sulphur or near heat sources e Always install the portable air conditioner properly Incorrect assembly or installation may cause failure to operate including injury fire and electric shock hazards e Do not place the power cord near a heater It may cause fire or electric shock e Do not use the power cord near flammable gas or combustibles such as gasoline benzene thinner etc It may cause explosion or fire e Do not operate or stop the unit by inserting or pulling out the power plug It may cause fire or electric shock e Do not damage or use an unspecified power cord It may cause fire or electric shock e Do not modify the length of the power cord It will cause fire or electric shock due to heat generation e Use the air conditioner on a single outlet circuit Do not share the outlet with other appliances It may cause circuit failure e Changing
28. water tank and discharged through the upper drain outlet e Use the MODE button to set the unit function to DEHUMIDIFY e Remove the exhaust hose from the unit Exhausting air outside of the room will nullify the DEHUMIDIFY function e Remove the rubber plug from the upper drain outlet shown in figure below in the front of the unit and attach the drain hose e Allow water to flow out continuously into a bucket or floor drain NOTE In DEHUMIDIFY ventilator fan speed is preset to maximize efficient operation You will not be able to adjust the fan speed You may also allow the water to drain by opening the lower drain outlet and placing the unit directly over a shallow pan Do not leave the unit unattended in case the pan fills and needs to be emptied CAUTION Water will run out immediately once lower drain cap is removed Place drain outlet over collection pan prior to removing cap CLEANING amp MAINTENANCE A IMPORTANT e Be sure to turn the unit OFF and unplug the unit before cleaning and servicing e Do not use gasoline thinner or other harsh chemicals to clean the unit e Never wash the unit directly under a tap or with a hose e Do not allow water to enter into any of the unit openings 18 CLEANING amp MAINTENANCE B CLEANING THE FILTER e Clean the air filter once every two weeks to remove dust build up and keep the fan in top performance e Remove the filter Grasp the filter an
Download Pdf Manuals
Related Search