Keating Of Chicago Flexible Tubing to Hard Piping 055173 User's Manual
Contents
1. Filter Tub Disconnected View B Table or Bench Item C Detail2. as shown in View A A If the fitting is not on center line of the radius on the pump mount housing assembly as shown use a 23 or 24 drill to remove pump housing covers 2 as shown in view A A to gain easier access to the top bolts holding the motor pump Loosen 4 bolts on motor pump to center 90 fitting as best as possible These covers will be re assembled with parts in the kit After adjustments are made to the motor pump to center 90 compression fitting as shown in view A A tighten the 4 bolts for the motor pump HardPiping057122 qxd Flexible Tubing to Hard Piping Installation Instructions for Motor Pump Part 055173 continued Page 2 of 2 Operation 2 Re Assembly Notes 1 Remove filter tub from motor pump housing assembly and set Your Kit Includes items with may not be included aside On 18 20 and 24 models only remove pipe nipple 3 8 ltem Part Qty Description NPT x 1 and discard Replace with pipe nipple 3 8 NPT x 1 A Peete i Be Sale tt here 1 2 item B See view A for proper dimensions from back of z coe Sie cea 2 a sump to front of quick connect On 14 filter tub see view A D 020101 8 Nut 5 16 Hex Head Serrated Flang for proper dimesions from back of sump to front of quick dis E 017142 4 Screw 5 16 18 x 3 4 Hex Head connect Place the filter tub into the filter cart assembly F 015227 2 Nut 1 4 Acorn S S Release the filter tub away from the pump housing as sho
3. SERVICE INSTRUCTIONS Part No 057122 www keatingofchicago com KEATING 1 800 KEATING OF CHICAGO INC Flexible Tubing to Hard Piping Installation Instructions for Motor Pump Part 055173 Page 1 of 2 Motor Pump Housing Covers See Note 5 2X Motor Pump Housing Assembly 90 Compression Fitting See Notes Hi Uh RH g 3 and 5 i Operation 1 Dis Assembly Filter Tub Assembly See Note 1 Beenaa Fo 4 N i Filter Tub Assembly in Unlocked Position Bracket SE Coupler See Note 4 Pull Rod See Note 2 Compression Fitting See Note 3 Make Sure Saftey Glasses are Worn Use these Service Instructions for the Notes 1 following Kit part s Drain and clean all oil from filter tub assembly Remove filter tub assembly from filter cart frame assembly This assembly will be turned over upside 057117 SE14 down for replacement of parts and adjustment to mating part on motor 057118 SE18 mount housing assembly 057119 SE20 057120 SE24 Remove pull rod and set aside this part will be used later Loosen compression fitting at pump output Do not remove 90 fitting from pump Remove 4 bolts holding bracket SE coupler This assembly will be replaced with new parts in kit The bracket and flex tubing with quick connect are to be discarded Inspect 90 compression fitting on the pump
4. SSION FITTING AT THIS TIME Attach item C to the pump housing with items D and E DO NOT TIGHTEN COMPLETELY AT re Motor Mount Housing Assembly Bolts Must Be Flush Not Tight 3 Attach filter tub pull rod handle using item Filter Tub Assembly F and I gt 4 Attach the pump mount covers using item G Filter Cart Frame Assembly 5 Inspect for spacers between casters and filter cart assembly If none are present remove T K amp D Bolts Only casters and place item J 2 on the casters rier TE aa for Models 20 threaded stem and reassemble using existing iter tu onnecte r gan J amp I See ane 2h SpE fasteners and item See Note 2 wide View Note 5 Note 2 See Note 1 6 Carefully turn filter assembly to the upright posi tion Release the filter tub pull rod and check for proper disconnect Reconnect the filter tub to the motor mount housing using handles If the assemblies do not connect properly it will be necessary to verify notes above were followed correctly Filter Tub K M N O Pull Rod See Note 3 F amp I See Note 3 7 Fill filter tub with oil per users manual cycle oil to check for leaks at fittings correct if needed Shown to Remove Any Play Between Tub and Filter Cart Note A Dimensions 9 5 16 for 14 Filter 11 3 8 for 18 Filter 12 3 8 for 20 Filter 14 3 8 for 24 Filter
5. wn G 004611 4 Screw 10 x 3 8 Sheet Metal Pan HD in side view Turn the entire assembly upside down as shown 037672 A R Sealant Locktite 262 017 oz in view B This step is critical to insure proper alignment J 056765 8 Washer Flat 7 16 ID x 1 00 OD x 078 THK between the motor housing quick connect and the filter tub K 017481 4 Screw 5 16 18 x 1 3 4 Hex HD SS quick connect Use table or bench making sure the Lora 1 Reinforcement Bracket ee M 015158 2 Acorn Nut 5 16 18 SS motor pump housing is off of the table bench N 052733 2 Washer 11 32 ID x 3 4 OD CAUTION IF FILTER ASSEMBLY IS PLACED UPSIDE DOWN O 000290 2 Washer Lock 5 16 Spilt ON A TABLE OR BENCH MAKE SURE UNIT IS SECURE SO AS NOT TO SLIDE OFF TABLE BENCH THIS TIME Play must be present for proper alignment of pump housing connect and filter tub quick connect Slide the filter tub assembly forward until the quick connects are engaged Tighten items D and E completely Tighten compres sion on item C Remove 2 bolts and washers K and add reinforcement bracket L Use longer 2 bolts pro Bottom View vided and discard old ones For 20 and 24 models Pump Mount Cover Mount Reinforcement add items D and K to reinforcement bracket and Bracket as Shown R K G See Note 4 tighten until snug on motor mount housing assem bly See Bottom View 2 Slide item C into position to connect the compression fitting on the pump s 90 fitting DO NOT TIGHTEN COMPRE
Download Pdf Manuals
Related Search