Home

Kathrein UFS 702si User's Manual

Contents

1. Since the channels in the channel pool are available to all favourites lists parental control marking must also be performed on the channels in the channel pool 31 Channel menu channel management Note 32 Path MENU gt Main menu gt Channels gt Favourites lists Select the right hand window with the button All Free sub selection and mark the necessary channels with the button Pause A question mark is placed in front of the secured channel channel name To delete a move the marked channel back into the grey bar and press the button again Alternatively channel marking can be performed directly in the channel pool Use the following path MENU gt Main menu gt Channels gt Channel pool When parental control is activated the five digit pin must be entered each time a marked channel is selected To ensure the effectiveness of the parental control the PIN must be entered when certain menus are displayed if parental control is active To deactivate the parental control e g of an evening switch the selection field Lock to OFF This does not change the markings and these become active again when parental control is reactivated Search Satellite search The newly found pro grammes are also stored in the programme list which is called up by pres sing twice However unlike in programme pool these are not attached to the end of the list but rathe
2. DECT telephones operate on the same frequency as these channels Interference may occur due to inadequate level or poor shielding of cable Scart connection to TV deactivated by accidentally pressing 0 button On System set up Time set up menu check Summer Time enabled and change as necessary Switch off receiver at mains switch from current channel wait 10 seconds and then switch back on Consult your antenna specialist Keep pressing the 0 button until the TV picture reappears on screen 67 Error detection troubleshooting and service Search for new channels Channel change Search for new channels that are not yet A channel has moved or is no longer present on the original frequency First delete the old channel as described and then start a search to find the channel at its new position See search page 34 ff See channel management page 24 ff Depending on the information you Here you can delete a channel as have available you can start a satellite described transponder or manual search You only need to know the transmitting satellite for the satellite search See channel management page 24 ff See search page 34 ff Here you can move delete and copy Depending on the information you channels as described have available you can start a satellite transponder or manual search You only need to know the transmitting satellite for the satellite search po See channel management pag
3. Satellite Channels Navigate in the currently selected list using the arrow buttons and 4 The channels in the favourites list left hand window are displayed with the channel numbers Items in the list can also be set directly by entering the channel number with the number keys 0 Press the button red to select a different favourites list e After a search the new channels are stored both in the channel pool and in the current favourites list left hand side of picture above Select the Channel arrangement sub menu The newly found channels can be seen at the end of the selected favourites list Channel menu channel management Note Move Delete You should delete uninteresting channels test cards or any other junk programming from your favourites list Use the button to switch the menu display transparency between variable and fixed fixed is non transparent In var mode the transparency can be increased or reduced using the Q buttons This function is very useful when deleting moving and inserting channels because with a high transparency setting it is easy to quickly see the type and content of the channels in the background Select the favourites list in the left hand window using the button e Move the required channel into the green bar using the Q and 4 buttons or by entering the channel number e Use the fol button green to move the channel on t
4. such as a Dolby Surround system for decoding Two channel stereo signals encoded 53 Audio settings Analogue outputs 54 in PCM format or complex multi channel surround signals Dolby Digital AC 3 can be transmitted on the digital socket Press the a button yellow to access the Digital analogue audio mode menu You can use this menu purely as an information display and press the a button yellow again to quit it immediately or you can change various settings In the right hand window you see the current signal status of the connections at the rear of your satellite receiver An analogue audio signal is received at the cinch sockets and via the TV and VCR Scart sockets In some cases bilingual programmes are also broadcast over the two Left and Right stereo channels If this is the case you would hear German through the left channel and English through the right for example To hear just one language use the g button to select Mono L or Mono R and confirm your selection by pressing the button The current selection is highlighted in white Most bilingual or multilingual programmes are however broadcast on separate audio tracks In this case the left hand window would display German under 1 and English under 2 and you would hear both languages in stereo Use the B buttons to select the language you want and confirm your selection by pressing the button The currently selected
5. then confirm the selection with Audio settings Setting the volume Muting Digital output Always follow the operating instructions for your Dolby Digital system TV P1002 Do 22 09 11130 Set the required volume level using the g buttons on the remote control of the receiver A bar indicator is displayed on the screen to show the set volume Press the button to mute the sound Mute is displayed Press the button again to restore the sound The receiver has an audio output for AC3 format Dolby Digital This gives you the opportunity to bring cinema quality sound into your living room Connect the digital audio output only to an appropriate system Only a few programme providers broadcast the AC3 format If no AC3 signal is received you can only make the normal stereo or mono settings and choose the languages that are broadcast Digital analogue audio mode In digital satellite technology the picture and sound are generally transmitted in digital format MPEG coded Where the term Analogue audio mode is used in this section it signifies that the digital signals are converted in the unit into audio signals and made available at the Left and Right cinch sockets and at the TV and VCR Scart sockets in analogue format By contrast in Digital audio mode the signals are transmitted in digital format via the Digital cinch socket to corresponding terminal devices
6. 1 Press the f button to switch to the main menu 2 Press the G buttons to get to the installation menu and confirm your entry by pressing 3 Press the 4 buttons to get to the DiSEqC menu and confirm your entry by pressing 4 Press the a buttons to select the UFO option 5 In the UFO menu press the a buttons to select UFO micro 6 Press and change the selection to RESET with the OO buttons then confirm your entry by pressing 7 Press f to exit the UFO menu press to confirm the changes 8 Press e1 three times to get back to the starting point Press the button to switch the receiver to standby mode Now you can connect the receiver to the antenna socket Press the button to switch the receiver on The registration is then performed automatically the screen briefly shows UFO micro active Connection and set up Connecting the unit Sat IF Connections Reception requirements The following section is intended specifically for specialist dealers You only need to pay attention to this section if you are carrying out the installation yourself The Connection examples section provides a sample configuration Do not connect the unit to the mains until all installation work has been properly carried out Refer to the information in the Safety instructions section Connect the Sat IF inputs on the receiver to the satellite recepti
7. DVB MPEG 2 signals The receiver uses the PID number to create a unique assignment for the video and audio data transmission The PCR PID is the identification number for the synchronisation signal The PCR PID is normally identical to the video PID For programmes broadcast in multiple languages the audio PID can be entered manually to assign a different language to the TV programme After the PID is entered the digital receiver automatically selects the audio data identified by the PID number from the data stream and assigns it to the video signal Picture In Picture function The symbol rate describes the quantity of data that is transmitted per second The symbol rate is measured in MSymbols s and is equal to the number of symbols received per second A transponder is a satellite channel which transmits TV and radio signals A satellite has several transponders Analogue transponders transmit only one TV channel and possibly multiple radio programmes on the transmission frequency Digital transponders simultaneously transmit several TV and several radio programmes at a transmission frequency If a programme provider is broadcasting several TV channels via a digital transponder we refer to the provider s channel package The terms digital transponder and channel package have the same meaning The video bit rate describes the quantity of data from the digitised video signal that is transmitted per second The Viterbi
8. DiSEqC signal is repeated once The DiSEqC signal is repeated twice 45 Installation UFO UFO min and UFO micro are satellite systems specific to Kathrein Please refer to the relevant operating manuals for the necessary setting parameters UFO mini OFF ON 2 Remote Freq XXXX 3 UFO micro OFF ON RESET Press the button to access the main menu Activate the desired sub menus using the specified number buttons X or with the programme buttons 4 The selected sub menu is framed in colour and the associated help text is displayed Then press the button to access the activated sub menu Branch into the additional sub menus in the same way The changes you make are only applied if you press the button in response to the Save changes prompt after you have exited the menu by pressing the button When you exit DiSEqC UFO micro settings an additional message appears confirming activation of UFO micro Various display time RC LCD download factory reset Display time G function 46 Path MENU gt Main menu gt Installation gt Various 1 9 The banner display time programme status information can be set from 1 to 9 seconds As an alternative signal quality can be assigned to the i button Banner Displays programme status information can be immediately switched back off by pressing the button again Signal quality Displays the Channel para
9. Scart VCR Scart CVBS CVBS CVBS YC RGB CVBS RGB offers the best TV picture quality RGB YC Select YC for an S VHS video recorder YC CVBS YC YC Explanation CVBS Composite Video Broadband Signal FBAS same as CVBS YC corresponds to S Video Y Brightness C Colour Installation Picture format 4 3 If 4 3 is set all programmes are displayed in the regular 4 3 format 16 9 When 16 9 is set all programmes broadcast in widescreen format and flagged appropriately are automatically switched to 16 9 format However this function only operates if your TV set can process and display 16 9 format pictures 6 volt switching voltage Digital audio Two modes are available for the digital output of your receiver Standard The signal at the digital output is encoded in PCM format PCM AC 3 If you have a Dolby Digital system you can select AC3 Dolby Digital mode If your receiver receives a Dolby Digital encoded audio signal the digital output is automatically switched to Dolby Digital format AC 3 Note In both modes press button A at any time to display the Digital analogue audio mode menu to check the current format of the digital output signal or make a different selection if necessary VCR signals TV gt VCR video return path ON When ON is selected the video and audio signals from the TV socket are still transmitted to the VCR socket even in standby mode OFF Slightly
10. across lines and columns and select the required channels All selected channels are immediately set by the receiver and displayed in the background 29 Channel menu channel management Delete one channel all channels in channel pool If necessary use the button to make the menu transparent Use the G and QO buttons to navigate across lines and columns and select the required channels All selected channels are immediately set by the receiver and displayed in the background If necessary use the button to make the menu transparent Use the fal button green to delete the selected channel Use the a button blue to delete all channels in the channel pool Channels that are deleted from the channel pool are only found again when the satellite search is repeated Antenna signal and reception parameters button i 30 DI XXP Traumk ASTRA19 Hg 12632 MHz v gus Horizontal UFTU T 22000 kS s UNIVER 5 6 VIG Lie VIC TV VIC TV VIVA VIVA PI UAOO Le VOX ALLU ETE 123 Gi EX Exit The Antenna signal sub menu i is used to align your parabolic antenna optimally if required Rotate the antenna so that the signal strength and reception quality scales are at their optimum In the event of very weak signals the signal strength scale may even fall to 0 In this case optimise the signal with the scale for the reception quality If Signal or L is shown in the display a valid
11. digital signal is being received However if No signal appears in the menu or appears instead of the L on the right hand side of the display then Channel menu channel management F 126 E 00 F 126 E 29 L either no signal is being received or the signal is not valid e g if the antenna is incorrectly aligned to a satellite with analogue signals The signal strength and reception quality values are also shown on the display Signal present invalid digital signal Cause the antenna is aligned to an incorrect satellite or receiving a faulty channel switch to another channel if necessary Parental control child lock PIN Path MENU gt Main menu gt Channels gt Parental control Lock OFF Parental control is deactivated ON Parental control is activated i e when a marked channel is selected you are requested to enter your PIN five digit security code To change the PIN code The delivery status of the PIN is 00000 To change the PIN activate the PIN menu item with the button 1 Enter the current PIN 00000 when delivered 2 Enter the new PIN XXXXX 3 Enter the new PIN again XXXXX Do not forget your PIN Your unit can only be reset to delivery status by your dealer customer service When the unit is in delivery status all channels are enabled However each channel can be marked individually preventing unauthorised access when parental control is activated ON
12. in a cupboard or on a shelf with insufficient ventilation Never cover the ventilation slits of the device Do not put any objects on the device and keep a clearance of at least 10 cm above the device so that the generated heat can be discharged without any difficulty Humidity insulation heat Protect the device against humidity and dripping and splashing water Do not place the device near the heating expose it to the sun or operate it in damp rooms Receiver features The UFS 702si and UFS 702sw receivers are suitable for receiving FTA digital satellite TV and radio programmes In addition to providing high quality pictures and sound these receivers also feature an attractive design in a modern housing Despite their small size the receivers have all of the features of large receivers such as an electrical and optical audio output for Dolby Digital AC 3 videotext teletext with memory for 800 pages a 16 character alphanumeric display for programme names radio data and much more Controls displays and connections This section provides a brief description of all the controls displays and connections The button symbols presented here can also be found in the description of the operating steps View of front panel flap folded down O02 RADIO BREMEN DIGITAL SATELLITE RECEIVER TV PPPE EEEE EEE KATHREIN Eiekroschock Gefahri AA uFs7o2si_ 2020079 Nicht ffnen VCR pz
13. language or audio track is highlighted in white Digitallanalog audio mode 3 Audio track s SUE Analog outputs 1 2 2ch Mono L 3 dd AC 3 Mono R P Digital output PCM Oe i Stereo displayed in the following screenshot indicates that only one language is being transmitted in stereo The content ofthe left hand window is dictated by the broadcaster Line 1 might indicate Deutsch or ger instead of Stereo for example VOL oK Choice Audio settings Digital output AC 3 general In the right hand window you see the current signal status at the digital output digital cinch socket Digitallfanalog audio mode 3 Audio track s Analog outputs 1 u 2 2ch Mono L 3 dd AC 3 Mono R P Digital output VOLH rem 0K Choice If PCM is displayed the digital signal is encoded in PCM format If AC 3 is displayed the audio signal is encoded in Dolby Digital format If available select the language or audio track you want from the left hand window by pressing the g button and press the ox button to confirm your selection The currently selected audio track is highlighted in white The number of languages and audio tracks offered is dictated by the programme provider A PCM encoded language or audio track is always displayed You may however also be offered two or more PCM encoded languages or audio tracks with one or more in AC3 fo
14. less power is used in standby mode in the OFF position VCR signal input signal at VCR Scart socket CBVS RGB Use the CBVS RGB setting when connecting a VHS video recorder or a DVD player recorder yc Use the YC setting when connecting an S VHS video recorder S Video 43 Installation VCR record The VCR Scart socket has two different modes for automatic VCR recording with the timer function Standard The video signal pin 19 on VCR Scart socket to the VCR is always available Pin 8 on the VCR Scart socket switching voltage is switched as an input meaning that when you press the playback button on your video recorder your satellite receiver automatically switches the video and audio signals coming from the video recorder to the TV Scart socket via the VCR Scart socket and from there to the TV set For timer controlled video recordings in standard mode you must enter identical start and end times on your video recorder and in the Timer Programming menu Sat Record The video output signal pin 19 from the VCR is always available When a timer event is active i e when the unit switches to the channel to be recorded at the pre programmed time 12 V is output at pin 8 of the VCR Scart socket A Sat Record compatible video recorder detects this voltage and automatically switches to record When the timer recording is finished pin 8 is switched back to input mode and is again ready to relay the VCR signal on p
15. number and channel name upon completion of numerical entry Display of programme name during operation when all other information has been processed Display of radio programmes during entry Display of radio programme name during operation Information that takes up more than 16 characters is displayed in scroll mode i e the area marked grey is moved to the left The following information is also displayed as scrolling text Start and end time of the current programme Name of the current programme Start and end time of the next programme Name of the next programme Display when device is muted Display when TV mode is activated using the button green The picture and sound then come from the TV set itself e g via cable or from another device attached to the TV set Display when the device is transferring a picture and sound signal from the video recorder to the TV set Important If you open a menu or information window in radio or TV mode using the 9 red yellow or G buttons the receiver no longer responds to the g buttons Press the button to close the window Important note on setting up receiver on a UFO micro system When registering the receiver to a UFO micro single cable matrix EXU 544 you must do the following Connect the receiver to the TV set but do not yet connect it to the ESU 32 antenna socket Perform a UFO micro reset on the receiver as described below
16. the placeholder channels appear at the end You can also increase the number of placeholders by copying a placeholder repeatedly from the channel pool to the favourites list After the search you should call up the Channel arrangement sub menu to look through and assess the new channels Uninteresting channels test cards or any other junk programming can be deleted from the left hand window with the button green A major advantage of the double memory organisation channel pool and favourites list is that the junk programming that is deleted from the list remains in the pool so it is not found again during the next search Another advantage is that channels that are accidentally deleted can be copied back into the favourites list from the channel pool Channels menu channel management Path MENU gt Main menu gt Channels gt Select the Channels menu using the menu button 9 the 4 buttons on the main menu and V1 0 18 10 0S Mainmenu Channels Manage Favourite Lists Copy Swap and Delete Search Manage Channel Pool Antenna Adjustment Signal Satellites Check Channel Parameter Installation Create Name of Favourite List Parental Control Select Cursor U D 1 2 Activate OK Exit EX Use the 4 buttons to select the further options If there is another sub menu layer press the button to open it If there is no further sub menu layer access the selection
17. 1 and 16 Transmission takes place with the FX byte The following matrix shows the associated DiSEqC sequences US OFF DiSEqC US 1 16 DiSEqC E0 10 38 FY E0 10 38 FY EO 10 39 FX lt 25 ms gt In the DiSEqC menu path MENU gt Main menu gt Installation gt DiSEqC if the option DiSEqC Repeat is set to 1 then the DiISEqC sequence repeats after 100 ms US OFF DiSEqC E0 10 38 FY lt 100 ms gt E1 10 38 FY US 1 16 DiSEqC E0 10 39 FX lt 25 ms gt EO 10 38 FY lt 100 ms gt E1 10 38 FY ON The selected satellite is enabled for your reception system only the ASTRA satellite is enabled at the factory OFF The selected satellite is disabled Installation Time offset Note Note Language Signals LNB DISEqc Various Select Cursor U D 1 2 Activate OK Exit EX Path MENU gt Main menu gt installation gt Time offset Following power up or after a power outage the time and date for the system clock timer are imported from the received data To ensure the receiver s time and date correspond to the local time the variation from the standard time must be specified The adjustment value time offset for Central European Summer Time is 2 hours and 1 hour for Central European Winter Time Please check the time offset the first time you use the unit and when the time changes in the Spring and Autumn and correct it as necessary Sele
18. 10 Pokito TV 12 15 Pok mon 12 40 Pretty Cure 13 10 Inuyasha 13 35 Detektiv Conan 14 0 to TV 14 10 One Piece 14 40 Yu Gi Oh 15 10 Teenage Mutant Ninja Turtles oK mone Informations Timer Ex Exit Press the button red dot to transfer a programme from the programme preview directly to the timer menu see Timer Press the button to exit the EPG 21 Channels menu channel management 22 Digital television technology makes a large number of channels available A reception unit suitable for the ASTRA 19 East und EUTELSAT HOTBIRD 13 East satellites allows you to receive over 800 FTA TV and radio programmes To allow you to manage and control this range of channels the memory for the lists is divided into two sections one channel pool for radio and TV respectively each with 2000 programme memory positions 8 assigned favourites lists for radio and for TV respectively each with 1000 programme memory positions Use the 8 button blue to switch between TV and radio New channels found during a search are stored in both the channel pool and in the currently selected favourites list at the end of the memory area for the selected satellite This area is set with empty channels known as placeholder channels at the factory PXXX anana Placeholder for Astra 19 satellite Pyyy gt gt Placeholder for Eutelsat 13 satellite When the channel pool is sorted alphabetically
19. 29 AstroTV N24 EinsFestival EinsPlus EinsExtra P 009 DAS VIERTE P 019 BR alpha RIL Television Gursor OK f Press the ex button twice to display a list sorted by channel number Press the i button to display the channel list in alphabetical order Press the G button again to sort the channel list by channel number again Select the required channel with the Q buttons followed by the button Channel selection Channel hopping display Select last channel Favourites list Press the button to display the last four selected channels Press the relevant cursor button QQQ to select a channel Press the button to switch between the last two selected channels Choose a kavouriterlist News Sports Music Shopping Liste 6 SPAIN HOTBIRD Press the button red to display the favourites lists The required favourites list can either be selected directly using the number buttons or with the a buttons followed by the button The receiver automatically switches to the last channel viewed in the selected favourites list Use the number buttons or the B buttons to continue channel selection Press the button twice to display the list of channels allocated to the selected favourites list Now select the required channel as described under Channel list TV radio 19 EPG Electronic Programme Guide 20 The EPG Electronic Programme Guide displays information on the cur
20. Activate OK Change Cur LIR Note To view your receiver s software version press i in the main menu it is also displayed during downloading Note that when you update the channel lists your custom channel arrangement in both sets of eight favourites lists TV and RADIO will be overwritten by the updated programme list 49 Installation 50 9 Start the software download from the INSTALLATION menu after selecting the Download menu 6 by pressing the button The download then runs through a number of phases with each phase accompanied by relevant information messages You can abort the various phases at any time Search for the download channel on the ASTRA satellite This search is performed the first time the unit is operated and may take a few minutes When the unit is restarted the saved download channel is set directly Load the receiver identifier This operation may also take several minutes You can select data from the data carousel depending on availability operating system channel lists After choosing option 1 Receiver software the following menu is displayed CAUTION Download software version VX X Download software version VX X Continue OK YES EX NO Press the ex button to perform a version check If there is an older version on the data carousel a message appears telling you so You can abort the download prematurely if necessary This information i
21. Channel pool sorted in alphabetical order and by satellites FTA new FTA encrypted and new encrypted channels e Copy sort delete channels all in a clearly arranged menu Search e Automatic satellite search SCPC suitable for TV and radio programmes with satellite selection High Low band fixed and freely definable symbol rates for FTA and encrypted channels e Automatic transponder search finds TV radio programmes on a transponder e Manual input of all reception parameters for experts e Channel renaming OSD On Screen Display e User friendly menu structure with variable and fixed transparency e Integrated operating instructions and function description for remote control e Menu languages German English French Italian Spanish Dutch Turkish and Portuguese EPG Electronic Programme Guide e Quick programme information on current and upcoming programmes e Programme preview with additional details several days in advance depending on programme provider e User friendly data import channel start and end date into timer Video audio e TV socket RGB YC S Video SVHS CVBS e VCR socket YC and CVBS e Automatic VCR to TV switch through e Automatic TV to VCR switch through in standby selectable e Digital output for PCM or Dolby Digital AC 3 coded audio signals e Separate cinch sockets for L R audio 58 Technical appendix e Volume adjustable in 20 stages mute e Language selection for multiling
22. Operator s manual DVB Satellite Receiver UFS 702swisi KATHREIN Antennen Electronic Preface Dear customer This operating manual is intended to help you make the fullest use of the extensive range of functions offered by your new Satellite receiver We have tried to make the operating instructions as easy as possible to understand and to keep them as concise as possible To help you understand particular specialist terms that cannot be translated we have added a short glossary at the end of the manual The power switch is an environmentally friendly feature If you will not be using your receiver for a longer period you should use the power switch to disconnect it from the power supply and save energy For shorter breaks you can switch the receiver to standby on the remote control which uses only a minimal amount of energy We wish you good reception and much pleasure using your new DVB satellite receiver Yours The KATHREIN team Important Information The channels available on the satellites and transponders are subject to continual change If changes do occur the new channels have to be set in the receiver because the factory preset programming corresponds to the status on the date of manufacture The information for these settings can be found on the Internet or in relevant magazines Your receiver is factory fitted with the latest software version We are however constantly working on adapting the softwa
23. P 013 P 014 P 015 P 016 P 017 P 018 P 019 RIL Television J SF P 020 Bayerisches F P 021 WDR K ln P 022 NDR FS NDS P 023 MDR FERNSEH P 024 hr fernsehen P 025 SR S DWEST P 026 S DWEST Fer P 027 rbb Berlin P 028 BR alpha P 029 Gureo Phoenix 3sat arte QVC Deutsch HSE24 AstroTV N24 EinsFestival EinsPlus EinsExtra je eis I j Press the 0x button twice to display a list sorted by channel number see Channel selection button to exit the list Channe list Press the 17 Channel selection Switch between TV radio mode Press the 8 button blue to switch between TV and radio mode and then select the respective channels Channel selection works in the same way in both modes Channel selection using number buttons and buttons Use the number buttons to select a channel directly 0 is also a channel number Use the B buttons to select the next or previous channel from the currently selected favourites list Channel list TV radio ans Channel list FIF GENERAL P 010 DSF P 020 Phoenix P 011 Bayerisches F P 021 3sat R P 012 WDR K ln P 022 arte i P 013 NDR FS NDS P023 QVC Deutsch P 000 TW1 P 001 Das Erste P 002 ZDF P 003 SAT 1 WP 004 RIL Televisio MAC aS eye E P 005 RTL2 P 006 VOX P 007 ProSieben P 008 KABEL1 P 015 P 016 P 017 P 018 hr fernsehen P 025 SR S DWEST P 026 S DWEST Fer P 027 rbb Berlin P 028 P 0
24. Video input 20 X Connector shield 21 X X VHS S VHS switching The Scart sockets are switchable between VHS and S VHS The switch is made by selecting System set up TV settings AV settings from the main menu VHS RGB The RED signal is connected to pin 15 the CVBS output to pin 19 S VHS C Y The C output is connected to pin 15 the Y output to pin 19 61 Technical appendix Connection example narunem r 6 ei aa z Electrical or optical AC 3 digital sound HiFi system Dolby Digital system 62 Short technical guide Channel package DiSEqco DiSEqC components DVB MPEG 2 EB NO ratio FEC OTR The channel package for a digital transponder normally includes several TV and radio channels Each channel package has a fixed assignment for the transponder transmission frequency for polarisation horizontal or vertical for the symbol rate and for the Viterbi rate or error rate DiSEqC Digital Satellite Equipment Control is a communication system between a satellite receiver master and the peripheral satellite components slaves such as LNBs multi switches rotating antenna systems It is a single master multi slave system i e there is only ever one master in the satellite system All activities start from the master If DISEqC switching matrices are cascaded the master receiver must transmit the DiSEqC signal several times so tha
25. age Vas 1 S N dB gt 53 TV system Audio Audio decoding MPEG 1 and 2 Layer 1 and 2 Sampling rate kHz 32 44 1 48 Frequency range kHz 0 04 20 Output voltage mV Typical 770 S N dB gt 65 Memory Flash RAM MB 2 SDRAM MB 8 Processor clock speed MHz 150 Power supply Power supply voltage V Hz 230 50 10 Power consumption power standby W lt 22 lt 2 LNB supply vert horiz V imA 14 18 Max 400 Control signal kHz 22 DiSEqC 1 1 UFO micro Connections Sat IF input output 2 x F socket TV VCR output 2 x Scart socket Audio output analogue 2 x Cinch socket Audio digital output electrical Cinch socket Audio digital output optical Standard OWG IEC 952 Data port RJ 11 socket General Ambient temperature limit C 5 to 40 Unit dimensions mm 280 x 50 x 180 Weight kg 1 2 60 Technical appendix Accessories 1 infrared remote control RC 660 2 batteries 1 5 V type LR 03 size AAA micro 1 Scart cable 1 operating manual Scart socket assignment Signal Pin no TV VCR AUX Right audio output 1 xX X Right audio input 2 x Left audio output 3 xX X Audio earth 4 X X Blue earth 5 X X Audio left input 6 X Blue signal 7 X X Switching voltage 8 X X Green earth 9 X X Data signal 10 Green signal 11 X X Data signal 12 Red earth 13 X X Data earth 14 Red signal C 15 X X Blanking signal 16 X X Video earth 17 X X Blanking signal earth 18 xX X Video output FBAS Y 19 xX X
26. ch is called up by pres sing twice However unlike in programme pool these are not attached to the end of the list but rather to the end of each available broadcasting sa tellite programme Here the placeholders availableinthe programme list are overwritten by the new programmes For ASTRA 19 East satel lite programmes the pro gramme positions from 0 299 are reserved for the HOTBIRD EUTELSAT 13 East satellite pro grammes programme positions 300 to 799 are reserved Manual input for experts 34 1 2 Frequeney T OE E 4 START Select Cursor U D 1 2 Activate OK Change Cur L R If the parameters satellite frequency polarisation symbol rate of the channel being searched for are known the transponder search can be used If for example a new channel launches within a known channel group a channel from that group can be preset by selecting the channel The necessary parameters are then imported in the transponder search If No signal is displayed on the START line reception is not possible Check the Satellite Frequency Polarisation and Symbol rate parameters again The search can only be started if Signal is displayed e Start the search by pressing the ox button Encrypted channels are indicated by Channels that you do not want to import can be deleted individually with the b
27. connections and operating states 1 Receiver and TV set power plugs are connected to wall socket 2 Antenna cables on receiver input 3 Receiver and TV set correctly connected by a Scart or cinch cable 4 Audio connections are made to Hi Fi or Dolby Digital system as appropriate 5 Receiver and TV set Hi Fi Dolby Digital system are switched on check power indicators 6 Receiver is responding to remote control A selection of troubleshooting tips is offered below No signall warning appears on some or all channels Remote control no longer responding Antenna signal of satellite reception system missing or faulty Incorrect oscillator frequencies set in LNB configuration menu Receiver or remote control command set may have been unintentionally changed Consult an antenna specialist to have it checked and repaired as necessary On Installation menu check LNB configuration for satellite in question High L O 10 600 GHz and Low L O 9 750 GHz and change as necessary Set infrared code 1 as described in operating manual under Remote control RC 660 check batteries Wrong time being displayed The following channels cut out Poor signal or no signal appears PRO 7 SAT 1 Kabel 1 DSF N 24 Tele 5 9 Live HSE 24 and Sonnenklar TV Black or blue screen no on screen displays Summer Time setting wrong An incorrect time was imported from the reception signal
28. ct the Time offset option with button 1 or with the QG button activate it with the button and set the required time offset with the Q buttons Confirm the change with the button If the time offset is incorrect the programme times and other times will be displayed incorrectly 41 Installation Language character set Select language Path MENU gt Main menu gt installation gt Language The menu languages available are German English Italian French Dutch Portuguese Spanish and Turkish Select character set factory setting Latin Automatic character set switching is defined in the DVB standard unfortunately not all programme providers comply with this standard at the current time meaning that characters from an incorrect character set may appear in a text This unit features automatic character set switching but different character sets can be preset if required e g enabling a Greek text to be viewed in the correct format Selection Auto Standard Latin Cyrillic Arabic Greek Hebrew Signal paths TV VCR picture format record digital audio TV Scart VCR Scart 42 Path MENU gt Main menu gt installation gt Signal paths The individual fields are activated and edited in the usual way Select the required input field using the or WG buttons and activate it with the 9 button The available parameters can then be selected with the O O buttons and confirmed with 4 TV
29. ctions with care before putting the device into service Power cable Make sure you do not damage the power cable Devices with damaged power cables must be disconnected by pulling the plug and repaired by a technician before being restored to service Only use the supplied mains adapter as intended There is a danger of life threatening electrical shocks Cleaning Pull the power plug before cleaning the device Use a dry cloth for cleaning and only clean the surface Do not under any circumstances open the device There is a danger to life due to electrocution if components are touched within the device Playing children Take care that children do not insert objects in the ventilation slits There is a danger of life threatening electrical shocks Earth connection The aerial system should be connected to earth or to the potential equalisation according to instructions Observe EN 60728 11 and any national regulations in the process There is a danger due to overvoltage or lightning Mains voltage Only operate the device with the specified mains voltage on the back of the device or on the external mains adapter The device may only be connected to the mains and switched on after establishing the connections to the aerial and the television set or to the cable network and the PC There is a danger of fire if the mains voltage is too high Repairs Have your device repaired by qualified technicians only No warrant
30. d ey EEEE Fy DATA INTERFACE Front panel controls and displays Rear panel controls and displays On Off switch with mains disconnect 1 LNB input 2 TV R button for switching between TV 2 LNB loop through input and radio mode 3 Electrical data stream output SPDIF 3 16 character alphanumeric display for Sony Philips Digital Interface Format channel names radio data etc for Dolby Digital AC 3 audio 4 Channel down button 4 Optical data stream output SPDIF 5 Channel up button Sony Philips Digital Interface Format for Dolby Digital AC 3 audio 5 Audio outputs L R cinch sockets Data cable 6 Scart socket for TV connection 7 Scart socket for VCR connection Receiver modular PC Connection 8 6 pin modular socket with RJ 11 port for sequence serial data transfer in service mode or a Gonnection connection for remote infrared receiver 9 Mains power cable Pin 6 RXD p a RXD Pin 5 TXD TXD Pin 2 GND GND Controls displays and connections O iw a z a lt P12 MDR FERNSEH P12 MDR FERNSEHE MDR FERNSEHEN R1 Rock Antenn Rock Antenne 10 05 12 00 Philharm po H zZ H 0 Q 9 K a w fe a u 0 5 12 00 12 05 Nachric a Das Erste TV Mode VCR Mode Inntal Radio The channel number and channel name are displayed on a 16 character LCD display Display of TV channel and channel name during numerical entry channel selection Display of TV channel
31. e the area to which you want to move the block Move the channel block out of the clipboard and into the target area green bar using the a button yellow Exit the menu with the button and confirm with 27 Channel menu channel management Delete channel block e Select the favourites list in the left hand window using the button e Move the first channel of the block to be deleted into the green bar using the 4 buttons or by entering the channel number e Activate the start of the block using the es button a B is displayed e Use the JG buttons or enter the channel number to select the end of the block all channels in the block are then marked with B e Use the a button green to move the marked block on to the clipboard Exit the menu with the button and confirm with Copy channel block copy from channel pool to favourites list e Select the favourites list in the left hand window using the button e Select the target area where you would like to insert the new channels with the JG buttons or by entering the channel number the grey arrow points between the two channels where the channels will be inserted e Select the channel pool in the right hand window using the button e Select another satellite if necessary e Use the button to select a list New Free All Free etc e Move the first channel of the block to be inserted into the grey bar wi
32. e 24 ff Here you can move delete and copy channels as described If despite studying this operating manual you still have questions about getting started with the unit or using it correctly or if unexpected problems occur please contact your specialist dealer The Kathrein customer hotline is also at your disposal Phone 0900 1122240 0 89 EUR per minute on land lines of Deutsche Telekom AG KATHREIN Internet www kathrein de KATHREIN Werke KG phone 49 8031 184 0 Fax 49 8031 184 306 Anton Kathrein StraBe 1 3 P O Box 100444 83004 Rosenheim GERMANY Antennen Electronic 936 2868 D 0107 ZWT Technical data subject to change
33. e from the listing and then press the button red dot to transfer its data into the timer Confirm the data import into the timer by pressing again To delete a timer event select the relevant line in the timer using the number pad or the 4 keys and then pressing the key Timer VPS v indicating VPS function active The time and date are retrieved from the DVB data transmitted by the transmitter When changing from Summer to Winter time and vice versa please adjust the Time offset in the Installation menu For Central European Summer time 2 hy For Central European Winter time 1 h Please note that some exotic channels sometimes do not transmit the correct time Check the date and time in the Timer Programming menu when programming Hinweis You can also control the timer and the video recorder by way of VPS Video Programme System To do so programme the timer as usual in the EPG Automatic Timer Setting function or directly in the Manual Timer Setting menu and then press the fal button yellow on the selected timer line to activate the VPS function A v is displayed Make sure the correct VPS time is entered in the Start column The VPS times can also be found in many listings magazines When you have imported the programme you want to record from the EPG into the timer you will automatically see the start time usually corre
34. ecording can be aborted prematurely only with the Stop key After an abort End is displayed The unit can then be operated as normal 37 Satellites Satellites for experts 38 Path MENU gt Main menu gt Satellites The satellites ASTRA 19 and Hotbird 13 are enabled at the factory Another six satellites such as EUTELSAT HOTBIRD are pre programmed When you expand your reception system you can make the necessary settings for enabling the 6 pre programmed satellites in the Satellites menu The selected satellite ls Satellite unlocked Satellite locked Press OK button to control or choose according satellite parameter Select Cursor U D 1 2 Activate OK Exit EX Only enable additional satellites when your reception system is prepared accordingly Otherwise a search on these satellites would once again store channels that have already been stored thus wasting programme memory positions Activate the desired satellite number e g using the number buttons and press the button to access the input menu 1 Enter change name Activate the NAME input field by pressing button followed by You can use the 2 buttons to select the letters upper and lower case or numbers Use the buttons to move the input position to the right or left When you have entered the desired name press to deactivate the input field again Satel
35. l Sound on off ON mode numerical input for channels parental control etc Select main menu amp red Favourites list selection green TV switching voltage and channel arrangement pool Volume Quit menu return to last channel Confirm entry select channel list when pressed twice Cursor operation in channel pool Select timer menu transfer a programme from EPG to timer menu KATHREIN Standby Select videotext teletext channel arrangement pool on yellow Audio mode channel arrangement pool WR blue Switch between TV Radio channel arrangement pool Select channel information or display signal quality Channel selection up down QHOUH Cursor buttons Select EPG Electronic Programme Guide Set menu transparency Remote control Remote control RC 660 The RC 660 remote control supports up to four devices which are supplied with the RC 660 as standard as well as the receivers of the UFD 5xx not UFD 552 554 558 and UFD 4xx families First switch all receivers off at the power switch To configure a receiver to an infrared code Switch on the relevant receiver On the remote control simultaneously press Address 1 Then switch the receiver off again at the power switch and do the same for the other units for second receiver amp f
36. l number Start and end time of the current and next programme Radio channel information Error signalling Pq GENERAL P 002 7 E ASTRAI9 f 32 10019 00 ZOE Mittagsmagazin A DolbyDigital l 13 00 13 15 heute In Deutschland We 2610 12 04 A two or more language channels Day of week soundtracks available button yellow With time Channel information is shown for a few seconds each time the channel is changed duration can be changed under Installation Various Display time or continuously with the i button if not set to signal quality The information for the current radio channel has the same layout F GENERAL P 002 Tr l F ASTRA S We 26 10 12 05 No signal indicates that an error has occurred in the reception system or in the receiver settings or that the transponder is not transmitting Check the Sat IF connection and the LNB configuration If you have changed settings compare them against the basic settings if you made a note of them as suggested On Screen Displays OSD Channel hopping display Press the button to display the last four selected channels Press the relevant cursor button QOQ to select a channel Channel list TV radio me Tu Channel list Fl GENERAL P 000 TW1 P 001 Das Erste P 002 ZDF P 003 SAT 1 l P005 RTL2 P 006 VOX P 007 ProSieben P 008 KABEL1 P 009 DAS VIERTE P 010 P 011 P 012
37. layback LNB settings Path MENU gt Main menu gt installation gt LNB ON Default setting OFF Operation without LNB signal e g on special multi subscriber systems In standby OFF Default setting On standalone systems only use the OFF setting otherwise the receiver will also supply power to the LNB in standby This may cause the power consumption of the receiver to increase from the typical value of 2 Watts to as high as 10 Watts in standby ON The LNB voltage remains switched on in standby e g to supply power in an appropriate multi subscriber system 44 Installation DiSEqcC Digital Satellite Equipment Control Path MENU gt Main menu gt installation gt DiSEqC 22 kHz signal Tone burst DiSEqc DiSEqC repeat On the DiSEqC menu the control signals must be set according to the needs of your satellite system OFF High Low Pos A B High Low Pos A B Opt A B OFF ON OFF 1 2 Select Cursor U D 1 2 Activate OK Change Cur L R 22 kHz inactive 22 kHz switches between High and Low band 22 kHz switches between two satellites Activates tone burst depending on the reception frequency Selects orbit position 1 3 or 2 4 Switches between orbit position 1 2 or 3 4 Select ON if you want to operate the receiver on a DiSEqC suitable satellite reception system used for cascaded switching matrices No repeat of DISEqC signal The
38. lites Note 2 Enter LO1 3 Enter LO2 At the factory LO1 and LO2 are preset to 9 750 MHz and 10 600 MHz If the LNB LO frequencies differ from the factory presets enter the relevant values here Activate with and use the number buttons to enter the LO frequencies Press y to finish Please make sure that a digital capable LNB is installed in your reception system 4 Enter orbit position The Orbit position parameter possible values 1 4 must be entered for control by DiSEqC DiSEqC 1 0 4 sat positions 1 4 DiSEqC 1 1 16 x 4 sat positions uncommitted switches 1 16 Off As matrix operation switches are required to operate DiSEqC 1 1 the cabling is highly complicated and should only be undertaken by an experienced installer Enable ON The selected satellite is enabled for your reception system OFF The selected satellite is disabled 5 Uncom switch Uncommitted switches in DiSEqC Mode Uncommitted Switches US are used on special satellite reception systems to pre select different groups In delivery status the Uncommitted switches are deactivated OFF 39 Satellites Setting and activation Enable 40 Path MENU gt Main menu gt Satellites 1 8 gt Orbit position 1 Select Orbit position 1 4 2 Select Uncom switch The Uncommitted switches function is activated in menu item 2 Uncom switch by switching from OFF to a value between
39. menu with the button Settings are performed using the QOQ buttons or the number keys Once you have finished changing the settings exit the menu with the button and press the button to save Favourites list channel arrangement move delete copy Channel Arrangement Favourite List Choose Favourite List A Choose Satellite Choose Channel Source New All FREE CA COPY channel from source Channel Pool Favourite Name to Favourite List EXTRACT or DELETE Parental Control INSERT SORT already in y Select Cursor U D 1 2 Activate OK Exit EX Press the ox button to open the menu The following display appears example 23 Channels menu channel management 24 In the Channel arrangement menu the following actions can be performed on channels Move Delete Copy The Channel arrangement menu shows the currently selected favourites list in the left hand window and the channels available in the pool in the right hand window Channel Arrangement A Satellite I Channels e ASTRA19 AllFree E 1 P00 DAS VIERTE P 005 Cursor 0 9 EPG Cursor EPG z I i TV i DPC TV2 extract insert copy PI Use the arrow buttons and to switch the focus between the left hand and right hand windows a yellow background behind the list heading indicates that a window is active left hand window active Favourites list and right hand window active
40. meters and signal menu This functions facilitates optimal antenna alignment Installation LCD display settings Download Factory reset LCD backlight Used to set the illumination level of the display in 6 stages Scroll speed Used to set the speed of the scrolling text in 5 stages Time indicator OFF The time indicator is switched off in standby ON The date and time are displayed in standby If the time indicator is switched to ON in standby the power consumption of the receiver increases to approx 7 8 Watts power consumption is typically lt 2 Watts when OFF Download Over Air see Software and list update via satellite With the factory reset you can separately restore Device settings and the channels in favourites list 1 general to the delivery status Select the appropriate sub menu and enter the PIN 47 Installation Perform factory reset on device settings PIN security code Time offset Menu language Character set Signal paths TV Scart VCR Scart TV gt VCR VCR signal Picture format VCR record Digital audio LNB In standby 22kHz signal Tone burst DiSEqc DiSEqC Repeat Enable ASTRA Enable EUTELSAT13 Enable all others LO1 LO2 Orbit pos ASTRA Orbit pos EUTELSAT13 Uncom switch Display time Function Brightness Scroll Speed speed of scrolling text Time indicator Name of favourites list LNB DiSEqc Satellites Vari
41. nection Also connect the satellite receiver VCR AUX Scart socket and the video recorder PVR using a Scart cable If you are recording using an external video recorder remember not to operate the receiver during recording otherwise all the on screen displays will appear on your recording If you want to play the sound on your Hi Fi system connect the audio cinch sockets to the input sockets on the Hi Fi system with an appropriate cable see Connection example The Dolby Digital output electrical optical is intended for connection to a Dolby Digital system see Connection example Inserting batteries into the remote control te Remove the cover on the rear of the remote control Insert the two supplied batteries into the remote control Ensure correct polarity of the batteries the and markings are indicated inside the battery compartment Slide the cover back into the housing until it locks in place Used batteries are special waste Do not throw spent batteries into your domestic waste take them to a collection point for old batteries Electronic equipment is not domestic waste in accordance with directive 2002 96 EC OF THE EUROPEAN PARLIAMENT AND THE COUNCIL dated 27 January 2003 on used electrical and electronic appliances it must be disposed of properly Please take this unit to a public collection point intended for this type of disposal at the end of its useful life 11 Remote contro
42. o the clipboard remove Select the target area using the and 4 buttons or by entering the channel number e Move the channel out of the clipboard and into the target area yellow bar using the button yellow Exit the menu with the button and confirm with 4 e Move the channel to be deleted into the green bar using the and 4 buttons e Move the channel from the green bar onto the clipboard with the fal button green Exit the menu with the button and confirm with a channel that is deleted from the favourites list in this manner remains available in the channel pool meaning that it could be inserted back into the favourites list if necessary 25 Channel menu channel management Copy Note Note 26 Select the favourites list in the left hand window using the G button Select the target area for the channels to be inserted with the and 4 buttons or by entering the channel number the blue arrow points between the two channels where the new channel will be inserted e Select the channel pool in the right hand window using the button e If necessary select a different satellite using the button Satellites 1 2 Cursor UID OK Use the button to select a list New Free All Free etc Channels Cursor UID OK e Move the required channel into the grey bar using the 4 buttons e Copy the selected channel into the favo
43. on system Use coaxial cable with an F standard connector If the F standard connectors are not yet fitted on the cable strip the insulation from the cable as shown in the following illustration and carefully twist the F standard connectors onto the ends of the cables until they are securely fitted When fitting the connector make sure that no wires from the braiding are touching the inner conductor so no short circuit can occur The quality of the reception signal depends on the connection Make sure that your own satellite antenna system is equipped at least with a universal LNB for digital reception in the high band range Reception system presets The presets for the control signals have been made for standard reception systems i e 14 18 V for polarity reversal and 22 kHz switching signal for low high band changeover on multi feed reception systems The preset will need to be changed in the installation menu under DiSEqC if tone burst switching matrices are used in the reception system Refer to the section headed Installation menu DiSEqC Always follow the operating instructions for the matrix used Connection and set up TV and Video recorder connection Audio connection Dolby connection Connect the satellite receiver TV Scart socket and the TV set using a Scart cable see Connection example If your TV has a stereo feature you can receive the sound in stereo via the Scart con
44. or third receiver and for fourth receiver Make sure only one receiver is on at a time To switch the remote control to an infrared code When you have configured all receivers to their infrared code to switch between units on the remote control do the following For the first receiver s remote address 1 press E for the second receiver for the third receiver amp and for the fourth receiver amp red Kathrein UFD 5xx code for remote control RC 400 The RC 600 and RC 650 remote controls cannot be replaced 13 Operating instructions Menu concept Note Pay attention to the bar at the bottom of the on screen display This provides hints on what to do next The structure of the menu concept is based on logical operating sequences You will find detailed descriptions of the selected menu items in the relevant sections of the operating manual The selected menus sub menus and options as well as the parameters to be set are each highlighted in colour or by a border The menus are self explanatory Viainmenu Channels Manage Favourite Lists Copy Swap and Delete Search Manage Channel Pool Antenna Adjustment Signal Satellites Check Channel Parameter Installation Create Name of Favourite List Parental Control Select Cursor U D 1 2 Activate OK Exit EX Press the button to access the main menu and use the buttons to
45. ous LCD Note 00000 1h 2h depending on mfg date German Latin RGB CVBS OFF RGB CVBS 4 3 Standard Standard ON OFF High Low OFF ON OFF ON ON OFF 9750 MHz 10600 MHz 1 2 OFF 4 Seconds Banner 5 maximum range 1 5 3 middle range 1 5 OFF Delivery status If you perform a factory reset then check the setting for Winter Summer time time offset Also change the menu language if necessary Note that if you changed your PIN it is reset to 00000 by the factory reset 48 Installation Restore channels in favourites lists 1 and 8 If you accidentally delete the channels in favourites list 1 GENERAL or 8 HOTBIRD you can reset the unit to delivery status here Your other favourites lists F2 F7 do not change Note Restoring favourites lists 1 and 8 is only possible if the pool has not been deleted Access to the channel pool is PIN protected If the channels in the pool have nevertheless been deleted reload the channel lists via Download Over Air Download Over Air Software update via satellite In the Download sub menu you can install new operating systems and channel lists individually onto your receiver via the ASTRA satellite update by Download Over Air For this your reception system must be aligned to the ASTRA 19 2 East satellite Variou Download Over Air EX Exit Factory Reset Exit EX Select Cursor U D 1 2 4d
46. r recording is started in stand by mode the unit switches back to stand by when recording is finished Automatic Timer Setting If timer recording is star ted in stand by mode the unit switches back to stand by when recording is finished Deleting a Timer Event 36 Press the button red dot to access the Timer Programming menu Up to 8 timer events for TV or radio programmes can be entered Please note that if you select VCR Record Standard the video recorder must also be set to identical recording times 5 F Select Line Cur U D Select Row Cur LIR Delete content of selected Line with OK button With the number pad or the 4 keys select the next free input field in the figure to the left it is timer number two One after another select the input field for date start and stop time and the programme to be recorded with the keys the input field is highlighted in white With the ox key you activate the input in the selected field the field is highlighted in black Enter the relevant data either directly with the number pad or by switching forward with the Q keys and accepting the inputs with After entering the date start and stop time and the programme to be recorded you can exit the timer menu with the key or enter additional timer events You can also import the timer data directly from the programme listings To do so select the programm
47. r to the end of each available broadcasting sa tellite programme Here the placeholders availableinthe programme list are overwritten by the new programmes For ASTRA 19 East satel lite programmes the pro gramme positions from 0 299 are reserved for the HOTBIRD EUTELSAT 13 East satellite pro grammes programme positions 300 to 799 are reserved Transponder search Path MENU gt Main menu gt Search gt Satellites During the satellite search all of the channels on a satellite are searched for Select Cursor U D 1 2 Activate OK Change Cur L R Press the button to be able to select the satellites enabled in the Satellites menu using the Q buttons Press the ex button again to confirm your choice Use the buttons to select Start and start the search by pressing the button Use the 4 buttons to choose whether to search solely for FTA channels solely for encrypted channels or for both FTA and encrypted channels Press the ox button to start the search When the receiver displays End in the search window exit the window with the button Import the channels into the pool by pressing the ox button Path MENU gt Main menu gt Search gt Transponder During the transponder search all of the channels on a transponder are searched for 33 Search The newly found pro grammes are also stored in the programme list whi
48. rate code rate error rate characterises the error protection used by the programme provider The DVB standard provides the following values 1 2 2 3 3 4 5 6 7 8 Short technical guide Glossary Conditional Access for decoding of encrypted programmes Cl Internationally standardised interface for CA modules EB NO ratio Digital signal to noise ratio EPG ss Electronic Programme Guide GHz Abbreviation for Gigahertz Giga billion LNB Low Noise Block Converter i O On Screen Display Analogue TV standard Television channels available on subscription e g PREMIERE PCR Programme Clock Reference PID See Short Technical Guide PIN _ Personal Identification Number _ PIP i Pool O Muting of sound See Short technical guide Channel pool Collection of all receivable TV and radio channels Receiver Satellite receiver pe ooo Video signal made up of three individual colour signals red green blue Transponder See Short technical guide UFO micro and Kathrein specific satellite signal processing systems UFO mini 65 Short technical guide VCR connection Video recorder connection Viterbi rate See Short technical guide Yc Y brightness C colour signal Video signal standard for S VHS recorders Zapping Frequent programme changing using the remote control 66 Error detection troubleshooting and service In the event of a malfunction first check all the cable
49. re to the wishes of our customers and to developments in technology The Software and Channel List Update section contains additional information Please keep the original packaging in case you need to return the product at any time Make a note of the receiver s basic settings so as to be able to restore them if necessary DiSEqC is a trademark of Eutelsat UFO micro and UFO mini are registered trademarks of KATHREIN Werke KG Contents Preface Contents Safety instructions important notes Receiver features Controls displays and connections Important note on setting up receiver on a UFO micro system Connection and set up Remote control Operating instructions Menu concept Menu tree Language selection OSD On Screen Displays OSD Channel notifications Error signalling Channel hopping display Channel list TV radio Channel selection Switch between TV radio mode Channel selection using number buttons and button Channel list TV radio Channel hopping display Select last channel Favourites list EPG Electronic Programme Guide Channels menu channel management Favourites list channel arrangement move delete copy Move Delete Copy Move channel block Delete channel block Copy channel block copy from channel pool to favourites list Change names of favourites lists Channel pool Delete one channel all channels in channel pool Antenna signal and reception parameter
50. rent and upcoming programmes The information provided is determined by the programme providers and differs widely from programme to programme Many programmes are broadcast with no usable ancillary information SI data The same is true with regard to the programme previews Some programme providers transmit no data others offer a programme preview with additional programme information days in advance Press the button to access the EPG The following display appears example P005 RTL2 Atul prorata O O Schule aus Pokito an Das d rft ihr auf keinen Fall verpassen hier erfahrt Ihr t glich wichtige Anime Infos erlebt spannende G ste und k nnt bei tollen Aktionen mitmachen Next programme 0K Programme preview Ex Exit You now have the following options Press the button to see information on the next programme Press the button to see a programme preview of the currently selected channel Depending on the programme provider you are shown a programme preview covering the current day or several days in advance see picture Use the AMOO buttons to scroll forwards or back wards in the programme preview on a line by line or page by page basis Once you have selected the programme you want you can press the button to view more details if available If no ancillary information is available a message is displayed telling you so EPG Electronic Programme Guide P 005 RTL2 We 26 10 05 12
51. rmat For radio programmes up to 20 PCM encoded audio tracks may be available which you can select using the g button and confirm by pressing the ex button When you select Dolby Digital AC 3 mode for digital audio the digital output is automatically switched to AC 3 as soon as a relevant coding is transmitted see Signal paths digital audio 55 Using the front panel If you have misplaced your remote control or if the batteries are empty you can still operate your receiver from the front panel Backup operation The power switch the TV R button for switching between TV and radio mode and the and 4 buttons for selecting channels are located on the front panel When the receiver is switched on using the power switch or after a short power cut the receiver switches to the state it was in previously i e ON or Standby If the receiver was previously in standby mode press one ON dn up of the buttons Ch up 4 or Ch down to switch the unit on depending on the display Because there are no number buttons no password PIN protected functions can be displayed 56 Receiver to receiver data transfer Preparation Channel list download Your receiver is able to receive data from another receiver via its RJ11 port For this the two receivers are connected with a null modem cable The transmitting receiver is the master and the receiving receiver i
52. s button i Parental control child lock PIN Search Satellite search Transponder search Manual input for experts Videotext teletext Timer Manual Timer Setting Automatic Timer Setting Deleting a Timer Event VPS oOo N O Oo WO NY Contents Satellites Satellites for experts Setting and activation Enable Installation Time offset Language character Set Select language Select character set factory setting Latin Signal paths TV VCR picture format record digital audio TV Scart VCR Scart Picture format Digital audio VCR signals LNB settings DiSEqC Digital Satellite Equipment Control UFO Various display time RC LCD download factory reset Display time function LCD display settings Download Factory reset Download Over Air Software update via satellite Video recorder PVR connection Recording Playback Return path Audio settings Digital output Digital analogue audio mode Analogue outputs Digital output Using the front panel Receiver to receiver data transfer Technical appendix Technical features Accessories Scart socket assignment VHS S VHS switching Connection example Short technical guide Glossary Error detection troubleshooting and service Safety instructions important notes DANGER WARNING CAUTION This page contains important instructions for putting the device into service and installing and connecting it Read these instru
53. s determined by the CAM or the Smartcard and does not originate from the receiver Note Depending on the load on the data carousel the load operation may take as long as an hour Save the downloaded data You must not switch the unit off during this phase Video recorder PVR connection Recording Playback Note Connect your recorder and the receiver VCR socket using a Scart cable If you have a S VHS S Video recorder from the Installation menu select the Signal paths sub menu and change the selection TV Scart VCR so that the YC signal is output at the VCR socket To record a programme now running set your recorder to record Note that the volume on the receiver is set to full during recording L 20 on the 7 segment display This is the only way to obtain the full audio quality on subsequent playback Also make sure that you do not perform any other actions on the receiver during this direct recording process any on screen displays would be recorded along with the programme For recording with the timer refer to the Timer section Playback via your recorder i e transmission of the signal from the VCR to the TV set takes place automatically when the receiver is operating or in standby The switching voltage from the recorder is detected by the receiver and the VCR signal is switched through to the TV set The 7 segment display shows VCR You can switch to the receiver channel at any
54. s the slave Only possible between two UFS 702 receivers The master and slave are both switched on Then the RJ 11 ports of the two receivers are interconnected by a zero modem cable Master e Press the 4 buttons simultaneously on the master unit e Press the button to transfer the TV Radio lists Slave Do not switch the receiver off while data is being saved the red LED comes on Flash IC memory can be damaged First Storing then a progress bar is displayed Download operating system Master e Press the 4 buttons simultaneously on the master unit Press the 4 button to transfer the operating system Slave Do not switch the receiver off while data is being saved the red LED comes on Flash IC memory can be damaged First Storing then a progress bar is displayed 57 Technical appendix Technical features Channels e 2 000 memory slots each for TV and radio programmes e 8 customisable favourites lists each with 1 000 channel slots e g for SPORT NEWS MUSIC categories etc e 8 satellites individually activated e 24 characters for channel station names e Channel selection by 1 2 or 3 digit input e Channel selection via UP DOWN buttons e Channel switching for two programmes with one button Last programme e Quick selection of last four channels viewed Channel hopping function e Selection of channels from channel list e
55. select the sub menus Press the 4 button to access the sub menus Use the buttons to select the sub menu options The settings under the various options are made either by pressing the buttons or using the number pad The main menus sub menus and individual options can be exited step by step using the button After each change you are asked whether you want to confirm 9 or cancel the changes Operating instructions Favourites list Channel pool Favourites names Parental control Satellites Transponder Manual Time offset Language Signal paths LNB DiSEqC Various Language selection OSD The language for the on screen display is set as follows OQ Installation Language gt gt gt OO gt English gt The languages available are German English Italian French Dutch Portuguese Spanish and Turkish It is also possible to change the character set Available options Latin Cyrillic Arabic Greek Hebrew Standard Auto Latin is preset Settings are made in the same way as the OSD language Once you have finished changing the settings exit the menu with the button and press the button to save 15 On Screen Displays OSD Channel information TV channel information F FTA Selected Selected channel unencrypted satellite or favourites list channel One or more encrypted Dolby Digital channel channels available Channe
56. sponding to the VPS time and the stop time When the VPS function is active v the start and stop times serve as a window within which VPS will start the programme even if it is delayed for example The timer record function remains active as long as the VPS information is being broadcast by the channel meaning recording may also be automatically started at an earlier point that is within the preset time window such as in the event of a knockout in the first round of a boxing match or later outside the window such as when a football match goes into extra time If you programme the timer manually from the menu do not forget also to enter the stop time so as to set a VPS time window If the programme you are recording is only short e g 15 minutes in duration choose a stop time to preset an adequate time window e g one to two hours In this way you will be sure that the VPS time window will not be exceeded if there is a lengthy scheduling change If you have unintentionally deleted a line and want to restore the original information quit the timer menu by pressing the button twice Please note that no remote control commands are accepted during timer recording to prevent OSD displays from unintentionally being recorded over the picture The volume is set to full during recording To indicate that timer recording is active the unit s channel indicator shows r E c if a command is received from the remote control Timer r
57. t all DISEqC multi switches in the cascade receive their commands These days DiSEqC components slaves must be reverse compatible i e respond to the analogue switching criteria from receivers that are only equipped with H V and 22 kHz control signals A DiSEqC switching matrix will work with analogue switching criteria until the DiSEqC command from the master is received All analogue switching criteria are then ignored DVB is the abbreviation for Digital Video Broadcasting DVB S refers to the transmission method S satellite MPEG is the abbreviation for Moving Picture Experts Group a working group that formulates internationally applicable standards for the digital compression of video and audio MPEG 2 has established itself as the standard for compression of digital TV signals MPEG 2 works up to a data rate of 100 MB s The EB NO ratio is a measure of the signal to noise ratio of a digital signal The value is not identical to the C N value familiar from analogue reception technology At EB NO values below 5 dB no reception is normally possible FEC is the abbreviation for Forward Error Correction The FEC error rate corresponds to the Viterbi rate One Touch Recording 63 Short technical guide PID PIP Symbol rate Transponder Video bit rate Viterbi rate 64 The PID Packet IDentification number is an identification number for video signals and audio signals in the digital data stream of
58. th the JG buttons e Activate the start of the block using the s button a B is displayed e Use the 4 buttons to select the end of the block to be inserted all channels in the block are then marked with B Copy the selected channel into the favourites list using the button blue Exit the menu with the button and confirm with 28 Channel menu channel management Change names of favourites lists Channel pool Note Path MENU gt Main menu gt Channels gt Favourites names You can also change the name of the favourites lists as required Select the entry field to be changed Name using or the G buttons and activate it with the button e Use the G buttons to select the letters upper and lower case or numbers e Use the buttons to move the input position to the right or left e After entering the new name deactivate the entry field with the button Exit the menu with the button and confirm with Path MENU gt Main menu gt Channels gt Channel pool The channel pool contains all of the channels of the selected satellite in alphabetical order The channel pool is generally PIN protected enter the 5 digit PIN Use f to select the satellite The sub selection New Free New CA All Free or All CA is made with the button The channels in the channel pool are sorted in alphabetical order Use the and QO buttons to navigate
59. time even without stopping playback on your recorder To do so press the fal button green To switch back to the recorder playback press the button green twice The a button green controls the TV switching voltage pin 8 at the TV Scart socket The TV switching voltage is activated when the video signal from the receiver or from the recorder is switched to the TV set During normal operation without a recorder use the button green to switch between the receiver channel and an additional video signal to the TV set This additional video signal to the TV set might for example come from your existing analogue antenna from a cable connection or from a DVD player connected directly to the TV The display of video signals available on the TV set is dependent on the specification of your TV set In the above operating mode with a recorder during playback the a button green would thus set the video sources from the TV the recorder and the receiver one after the other 51 Video recorder PVR connection Return path 52 The video signal from the TV set can be returned to your recorder in standby mode If you want to use this function from the Installation menu select the Signal paths sub menu and then choose VCR signals Open the VCR signals menu using the button Activate the TV gt VCR input field using the button and change the selection to ON with the Q buttons
60. ual TV programme broadcasts and additional channel selection in radio mode e Stereo 24 bit 96 kHz audio Additional features e On unit controls for channel volume and radio TV switching e 16 character LC display e Timer for eight events TV or radio e Timer with VPS function e Optimum alignment of parabolic antenna by signal strength and reception quality e Videotext teletext reinsertion for viewing on TV e Internal teletext videotext e 800 page teletext videotext memory Prepared for UFO mini UFO micro Kathrein specific Software Update e Via data interface RJ 11 port separately for a Operating system b TV channel lists c Radio channel lists d Unit setting e Via satellite separately for a Operating system b TV and radio channel lists General e Remote control 36 buttons 4 addresses e Power switch 59 Technical appendix Type CE UFS 702si UFS 702sw Order no 20210079 20210080 Colour Silver Black RF properties Input frequency range MHz 950 2150 Input level range dBuV 44 83 Reception threshold EB NO lt 4 5 TV system Video Modulation FEC demultiplexer DVB S standard Video resolution CCIR 601 720 x 576 lines Input data rate MSymb s 2 45 Video decoding MPEG 1 and 2 compatible Bit rate MBit s 1 5 15 Frequency range MHz 0 02 5 Output volt
61. urites list using the button blue The unit recognizes channels that are already stored in the current favourites list a sign is then displayed in the blue arrow between the two windows Exit the menu with the button and confirm with Channels that you have accidentally moved or deleted e g by pressing the a button green repeatedly can be restored by exiting the menu with the button and then Channel menu channel management Move channel block answering the query Save changes with NO i e press the button again The Move Delete and Copy operations that are displayed in channel management can also be performed on channel blocks Select the favourites list in the left hand window using the G button Move the first channel of the block to be moved into the green bar using the 4 buttons or by entering the channel number Activate the start of the block using the button a B is displayed Use the JG buttons or enter the channel number to select the end of the block all channels in the block are then marked with B Channel Arrangement f 1 ME ASTRA19 AllFree E Eu 1 W L P 00 t Cursor 0 9 EPG Cursor Il EPG z z i DPC TV2 TV PI extract insert copy J J Use the fol button green to move the marked block on to the clipboard remove Use the G buttons or enter the channel number to select the target area i
62. utton blue New channels are indicated by Import the channels into the pool by pressing the y button Path MENU gt Main menu gt Search gt Manual If neither the satellite search nor the transponder search finds the channel you are looking for you can enter all the relevant reception parameters in the Manual input function Manual input is very useful for example if you know the reception data of the channel you are looking for but the channel does not broadcast all the time Videotext teletext When you press the button the receiver processes the videotext teletext service data for your TV set to display even when the signal is encrypted During the search the page which is being searched for is displayed in the top left hand corner with the time and date displayed at the top right When the search is finished the videotext teletext being broadcast by the relevant programme provider appears You have several options for calling up the desired pages Input with number pad Page by page using the a buttons Press the i button to return to page 100 Press the button to switch between the last two pages displayed Press the button to change the transparency of the videotext teletext Press the button to activate special functions e g double sized lettering Press the or button to exit videotext teletext 35 Timer Note Manual Timer Setting If the time
63. y claims will be accepted if the device is opened and an attempt is made to repair the device without any authorisation The electrical safety of the device can be put at risk by handling the device inappropriately The manufacturer assumes no liability for any accidents of the user while the device is open Connections Incorrect wiring of the connections can result in malfunctions or damage to the device Long periods of absence Thunder storms Always switch of the device at the mains switch in the event of long periods of absence or thunder storms You can disconnect the device from the mains by pulling the power plug if your device does not happen to have a mains switch This also applies to any other devices connected to the device We also recommend disconnecting cable networks Observe any timer programming procedures receiver and switch the device back on again in due time before recording begins Place of installation Every electronic device generates heat The heat generated by the device is within an acceptable range however Sensitive furniture surfaces and veneers may change their colour in the course of time due to the constant exposure to heat In the same way the feet of the device may cause treated furniture surfaces to change their colour If necessary place the device on an appropriate firm and flat base Ventilation The heat generated in the device is discharged sufficiently Nevertheless do not install the device

Download Pdf Manuals

Related Search

Related Contents

Eval. board Users Manual ver. 1.1  Power-SOL UPSステーションコントローラ for Windows 取扱説明書  KET-3000W4 S-Mini AC Drive User Manual KOMAL  仕 様 書  Mise en page 1 - Communauté de communes Essor du Rhin  Dell PP29L User's Manual  Sears 110.4778* Washer User Manual    2N PBX Assistant USER MANUAL PBX Assistant  Bedienungsanleitung Luftentfeuchter RT 20  

Copyright © All rights reserved. Failed to retrieve file