JVC HR-S2902U User's Manual
Contents
1. VHS Set S VHS ET to OFF pg 11 To record in VHS on an S VHS cassette Insert a cassette marked S VHS The S VHS indicator lights up on the display panel Then set S VHS MODE to OFF C pg 12 The S VHS indicator goes off The VHS recording mode is selected NOTE When playing back a tape that has been recorded in S VHS or S VHS ET the S VHS indicator lights up on the display panel regardless of the S VHS ET or S VHS MODE setting f Timer Recording Up to 8 timer recording programs can be made using express timer programing method as far as a year in advance Remember the clock must be set before you can program the timer Turn on the VCR and TV and select the VCR channel or AV mode NOTES If all the 8 programs have already been set PROGRAM FULL appears on the TV screen After timer recording is completed the VCR turns off automatically You can program the timer recording while a regular recording is in progress the menu screens will not be recorded Even if a power failure occurs the VCR keeps your timer programs However the clock time channel settings and other menu settings are lost As a result when the power is supplied again to this VCR after the power failure this VCR starts the Plug amp Play setting automatically to restore the clock time and channel setting If the clock time and channel setting are restored correctly eac2. 1 Disconnect the TV antenna from the TV 2 Connect the TV antenna cable to the ANT IN terminal on the rear of the VCR 3 Connect the supplied RF cable between the TV OUT terminal on the rear of the VCR and the TV s antenna input terminal AV Connection improves picture quality during tape playback If your TV is equipped with audio video input connectors nm Connect an audio video cable between the AUDIO VIDEO OUT connectors on the rear of the VCR and the audio video input connectors on the TV Connect the antenna VCR and TV as shown in the illustration S video Connection allows you to make the most of the S VHS picture performance If your TV is equipped with a S video input connector 1 Perform RF Connection previously described 2 Connect a S video cable between the S VIDEO OUT connector on the rear of the VCR and the S video input connector on the TV 3 Connect an audio cable between the AUDIO OUT connectors on the rear of the VCR and the audio input connectors on the TV Even if you are using audio video cables to connect your VCR to your TV you must also connect it using the RF cable This will ensure that you can record one show while watching another E1 Perform Plug amp Play setup Plug the AC power cord into an AC outlet Do not turn on the VCR The clock and tuner channels will be set automatically The time and date can be set automatical
3. Format Maximum recording time SP EP AC 120 V 60 Hz 16 W 1 5 W 5 C to 40 C 41 F to 104 F 20 C to 60 C 4 F to 140 F Horizontal only 435 mm x 94 mm x 248 mm 17 3 16 x 3 3 4 x 9 3 4 2 7 kg 5 9 lbs S VHS VHS NTSC standard 210 min with ST 210 video cassette 630 min with ST 210 video cassette VIDEO AUDIO Signal system Recording Playback system Signal to noise ratio Horizontal resolution VHS S VHS Frequency range Normal audio Hi Fi audio Input Output NTSC type color signal and EIA monochrome signal 525 lines 60 fields DA 4 Double Azimuth head helical scan system 45 dB 230 lines 400 lines 70 Hz to 10 000 Hz 20 Hz to 20 000 Hz RCA connectors IN x 1 OUT x 1 S video connectors IN x 1 OUT x 1 TUNER Tuning system Channel coverage Frequency synthesized tuner VHF Channels 2 13 UHF Channels 14 69 CATV 113 Channels RF output Channel 3 or 4 switchable preset to Channel 3 when shipped 75 ohms unbalanced TIMER Clock reference Quartz Program capacity 1 year programable timer 8 programs Memory backup for timer is not supported ACCESSORIES Infrared remote control unit Lithium battery CR2032 RF cable F type Provided accessories Specifications shown are for SP mode unless specified otherwise E amp O E Design and specifications subject to change without notice Ai WARRANTY Only in U S
4. is displayed on the display panel When AUTO TIMER is set to ON pg 11 the timer recording standby mode automatically resumes when you turn off the VCR Program overlap warning display If PROGRAM NOT COMPLETED PROGRAM OVERLAP appears you have another program overlapping the program you have just made The Program Check screen appears and conflicting programs will start blinking PR START STOP CH DATE 1 8 00P 10 00 12 12 24 10 00A 10 45 40 11 30P 1 00 125 9 00P 10 00 10 12 24 PROGRAM NOT COMPLETED 2 3 PROGRAM OVERLAP 4 5 6 7 8 A Y THEN p PROG END Example Program 1 you have just made and Program 4 overlap each other E Select program to modify PR START STOP CH DATE Press AV then press OK or gt 10 00 5 io You can only select one of the Tee 10 0010 overlapping programs If you do not mind this overlap press PROG to finish the timer program setting The program starting earlier or program with the lower program number will be recorded FA Cancel or change program setting To cancel a program press CANCEL when start STOP 9 00PM _ gt 10 00PM the Program screen you do not want is TE shown THEN PROG END PROGRAM 4 DA CH 12 24 03 10 SP WED To change a program press the Ae ay appropriate button START Number PRESS key 1 and or 4 STOP Number key 2 and or 5 DATE Number ke
5. A JVC LIMITED WARRANTY VCR EXCHANGE 90 JVC COMPANY OF AMERICA warrants this Video Cassette Recorder and all parts thereof except as set forth below ONLY TO THE ORIGINAL PURCHASER AT RETAIL to be FREE FROM DEFECTIVE MATERIALS AND WORKMANSHIP from the date of the original retail purchase for the period shown below The Warranty Period LABOR 90 DAYS PARTS 90 DAYS THIS LIMITED WARRANTY IS VALID ONLY IN THE FIFTY 50 UNITED STATES THE DISTRICT OF COLUMBIA AND IN THE COMMONWEALTH OF PUERTO RICO WHAT WE WILL DO If this product is found to be defective within the warranty period JVC will at its option either repair or replace the defective part s or replace the product with a new or refurbished functionally equivalent product Within 90 days from date of retail sale repair or replacement will be at no charge WHAT YOU MUST DO FOR WARRANTY SERVICE Please do not return your product to the retailer Instead please box the product carefully preferably in the original carton and ship insured to the JVC repair replacement facility nearest you To obtain the address of the location nearest you please call 800 537 5722 or visit our website http www jvc com A COPY OF YOUR BILL OF SALE A COMPLETED WARRANTY REPAIR REPLACEMENT FORM AND ALL OF THE ORIGINAL ACCESSORIES WHICH CAME WITH YOUR UNIT MUST ACCOMPANY THE PRODUCT TO BE ELIGIBLE FOR REPAIR REPLACEMENT UNDER WARRANTY If you have any questions concerning your JVC Product
6. another VCR audio video output connectors on another VCR To audio video output To audio video input Another VCR f another VCR is monaural connect this VCR s AUDIO L IN or OUT connector to the audio output or input connector on another VCR Example 2 When another VCR is S VHS VCR and equipped with S VIDEO input connector This VCR for playback To AUDIO OUT t t t To S VIDEO OUT Audio cable not supplied S video cable not supplied U To video input J l L To S video input Another VCR for recording Example 3 When another VCR is S VHS VCR and when using this VCR as the recording VCR This VCR for recording To AUDIO input FF tT To S VIDEO input Audio cable not supplied S video cable not supplied To audio output J Another VCR for playback To S video output FA Load cassettes Insert the playback cassette into the playback VCR and the cassette to be recorded on into the recording VCR EJ Select input mode on recording VCR Select the correct external input on the recording VCR On this VCR when using this VCR as the recording VCR Select F 1 when connecting the other VCR to the audio video input connectors on the front panel Press AUX or CHA V on the Remote Or on the VCR press PAUSE CH and then FF CH or REW CH See step H in Basic Recording F pg 9 E1 Select video input connector
7. condition How to use the Remote Before use insert the lithium battery CR2032 correctly with the plus side up into the battery compartment To open it Bal press the release tab and bares carefully pull the compartment out The Remote can operate most of your VCR s functions as well as basic functions of JVC TVs Point the Remote towards the remote sensor on the target component The maximum operating distance is about 8 m To operate a JVC TV use any of the following buttons TV POWER TV INPUT TV CH or TV VOL NOTE If the Remote does not work properly remove its battery wait for a few seconds replace the battery and then try again Video heads cleaning The heads get dirty in the following cases in an environment prone to extreme temperature or humidity in a dusty environment e flaw dirt or mold on video tapes continuous usage for a long time Use a dry cleaning cassette TCL 2 when Rough poor picture appears while a tape is played back The picture is unclear or no picture appears USE CLEANING CASSETTE appears on the screen only with SUPERIMPOSE set to ON F pg 12 ATTENTION To mobile phone users Using a mobile phone in the vicinity of the VCR may cause picture vibration on the TV screen or change the screen to a blue back display On placing the VCR Some TVs generate strong magnetic fields Make sure to pl
8. on recording VCR When using this VCR as the recording VCR select the appropriate mode F pg 12 When using S VIDEO input connector on the front panel set FRONT AUX INPUT to S VIDEO When using VIDEO input connector on the front panel set FRONT AUX INPUT to VIDEO E Select edit mode Set the edit mode to ON for the VCRs if such a mode is equipped On this VCR set PICTURE CONTROL to EDIT i pg 11 EJ Start playback Press PLAY B gt on the playback VCR Start recording Press REC on the recording VCR Various connection for editing tapes The following three methods can be used for editing tapes VHS to S VHS editing VIDEO VIDEO connection Although the picture quality is inherently limited by the original VHS quality the edited tape has better picture quality than those made by VHS to VHS editing S VHS to VHS editing VIDEO VIDEO connection Since the original source is recorded in S VHS mode the edited tape has better picture quality than those made by VHS to VHS editing S VHS to S VHS S VIDEO connection Original picture quality of S VHS made can be duplicated with minimal picture degradation This is the best editing method you can use on S VHS VCRs ear eee f Specifications GENERAL Power requirement Power consumption Power on Power off Temperature Operating Storage Operating position Dimensions W x Hx D Weight
9. picture resumes During still picture holding PAUSE II for more than 2 seconds also starts forward slow motion playback If you press PAUSE If again still picture resumes NOTE During slow motion some noise may appear on the TV screen Press CHA Y on the Remote to eliminate the noise CONTINUED ON NEXT PAGE SY 9 Reverse a Forward REVIEW a Reverse Reverse Reverse Slow Normal Forward search play slow motion play search 3 steps motion 1 step 4 steps 1 step When the tape is not running Rewind fast forward Press REW lt lt or FF BP Eject the cassette Press STOP EJECT Ml 4 You can also eject the cassette when the VCR is turned off Turn off the VCR Press POWER I Playback Features Turn on the VCR and TV and select the VCR channel or AV mode Adjusting tracking condition Tracking Adjustment Automatic tracking adjustment Whenever you insert a tape and start playback automatic tracking starts working and continuously analyzes the signal to enable optimum picture quality during playback Manual tracking adjustment If automatic tracking cannot eliminate noises well during playback follow the procedures below On the Remote El Press SP EP during playback to activate manual tracking F Press CHA V to eliminate the noises Press it briefly for a fine adjustment or press and hold for a coarse adjustment Press SP EP again to reactivate aut
10. please contact our Customer Relations Department at 800 252 5722 WHAT IS EXCLUDED The warranty does not cover 1 Products which have been subject to abuse accident alteration modification tampering negligence misuse faulty installation lack of reasonable care or if repaired or serviced by anyone other than a service facility authorized by JVC to render such service or if affixed to any attachment not provided with the products or if the model or serial number has been altered tampered with defaced or removed Initial installation installation and removal from built in entertainment centers and other mounting systems Operational adjustments covered in the Owner s Manual normal maintenance including head cleaning Damage that occurs in shipment due to act of God and cosmetic damage Signal reception problems and failures due to line power surge Products used for commercial purposes including but not limited to rental Accessories Batteries except that Rechargeable Batteries are covered for 90 days from the date of purchase ONAALRWND There are no express warranties except as listed above AFTER THE WARRANTY Please contact JVC s Customer Relations Department at 800 252 5722 to obtain the cost of out of warranty repair or replacement THE DURATION OF ANY IMPLIED WARRANTIES INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY IS LIMITED TO THE DURATION OF THE EXPRESS WARRANTY HEREIN JVC SHALL NOT BE LIA
11. to LANGUAGE then press OK or gt repeatedly until the desired language is selected Press MENU to return to normal screen SELECT WITH roe w AND 0K PRESS MENU TI Language selection will be reset to ENGLISH after a power failure occurs Clock Setting Perform clock setting only if the clock has not been set correctly by the Plug amp Play setting or if you use a cable box Turn on the VCR and TV and select the VCR channel or AV mode Preparations El Access Main Menu screen then Initial MAIN MENU FUNCTION SET Set screen FUNCTION Press MENU on the Remote Press AV to move the highlight bar arrow to INITIAL SET then press OK or gt PRESS aY THEN OK PRESS MENU TO END FA Access Clock Set screen Press AV to move the highlight bar oe to CLOCK SET then press OK or INITIAL SET CLOCK SET LANGUAGE ENGLISH SELECT WITH 4 AND OK PRESS MENU TO END Setting clock semiautomatically Semiauto Clock Set You can change the host channel D S T Daylight Saving Time time zone setting manually First follow steps Hl to A in Preparations above then go to the following steps NOTE The time set previously will be erased when AUTO CLOCK HOST CH D S T or TIME ZONE setting is changed i Set Auto Clock to ON CLOCK SET Press OK or gt on the Remote repeatedly to TIME ie YER move the highlight bar to AUTO
12. BLE FOR ANY LOSS OF USE OF THE PRODUCT INCONVENIENCE OR ANY OTHER DAMAGES WHETHER DIRECT INCIDENTAL OR CONSEQUENTAL INCLUDING WITHOUT LIMITATION DAMAGE TO TAPES RECORDS OR DISCS RESULTING FROM THE USE OF THIS PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY ALL EXPRESS AND IMPLIED WARRANTIES INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE ARE LIMITED TO THE WARRANTY PERIOD SET FORTH ABOVE Some states do not allow the exclusion of incidental or consequential damages or limitations on how long an implied warranty lasts so these limitations or exclusions may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state JVC COMPANY OF AMERICA 1700 Valley Road DIVISION OF JVC AMERICAS CORP Wayne New Jersey 07470 http www jvc com REFURBISHED PRODUCTS CARRY A SEPARATE WARRANTY THIS WARRANTY DOES NOT APPLY FOR DETAIL OF REFURBISHED PRODUCT WARRANTY PLEASE REFER TO THE REFURBISHED PRODUCT WARRANTY INFORMATION PACKAGED WITH EACH REFURBISHED PRODUCT For customer use Enter below the Model No and Serial No which is located either on the rear bottom or side of the cabinet Retain this information for future reference Model No Serial No Purchase Date Name of Dealer S25 JVC PLEASE COMPLETE THE FOLLOWING PLEASE NOTE P O BOXES ARE NOT ACCEPTABLE NAME STREET ADDRESS CITY STATE ZIPCODE DA
13. CLOCK RnIunInEanT then press AV so that ON is selected DST AUTO HOSTCH AUTO CATV TIME a j Then PRESS a v THEN Kas PRESS MEN TO END FA Select host channel You can either select AUTO or enter a PBS channel number Press OK or gt to move the highlight bar to HOST CH then press AV repeatedly until AUTO or the desired PBS channel number is selected Some PBS channels do not transmit clock setting data EJ Select D S T mode Press OK or gt to move the highlight bar to D S T then press AV repeatedly until the desired setting is selected UTO Select if you want to adjust your VCR s clock automatically by the incoming signal from the host channel Auto Daylight Saving Time enables automatic adjustment of the VCR s clock at the start and end of Daylight Saving Time Be sure to select the correct time zone manually in step Ea ON Adjustment will be made by the built in clock itself OFF Select when Daylight Saving Time does not apply to you EJ Select time zone Press OK or gt to move the highlight bar to TIME ZONE then press AV repeatedly until AUTO or the desired time zone is selected Each time you press the button the time zone changes as follows lt gt AUTO gt ATLANTIC lt gt EASTERN gt CENTRAL gt MOUNTAIN gt PACIFIC gt ALASKA lt gt HAWAII gt back to the beginning El Complete Semiauto Clock Set Press MENU t
14. ET then press OK or D gt PRESS PAE 0K PRESS MENU TO END FA Access Manual Channel Set screen Press AV to move the highlight bar arrow to MANUAL CHANNEL SET then press OK or TUNER SET BAND AUTO CHANNEL SET MANUAL CHANNEL SET SELECT WITH xa AND OK PRESS MENU TO END E Add or skip desired channels To add channels MANUAL CHANNEL SET SATY Press the Number keys on the Remote CH 45 ADD f A to input a channel number you want to add PRESS NUMBER KEY 0 9 OR 4 THEN OK Press OK or gt to set to ADD PRESS MENU TO END Repeat 1 to 2 to add other channels Press MENU to return to normal screen To skip channels Press AV or the Number keys to select a channel number you want to skip Press OK or gt to set to SKIP Repeat 1 and 2 to skip other channels Press MENU to return to normal screen nm o nm oo After a power failure occurs band selection will be reset to CATV Playback Basic Playback Turn on the VCR and TV and select the VCR channel or AV mode E Load a cassette Make sure the window side is up the rear label side is facing you and the arrow on the front of the cassette is pointing towards the VCR Do not apply too much pressure when inserting The VCR turns on and the count
15. IONAL ELECTRICAL CODE ANSI NFPA 70 GROUND CLAMP NEC NATIONAL ELECTRICAL CODE PORTABLE CART WARNING Symbol provided by RETAC 2 Product and Cart Combination A product and cart combination should be moved with care Quick stops excessive force and uneven surfaces may cause the product and cart combination to overturn 3 Water and Moisture Do not use this product near water for example near a bath tub wash bowl kitchen sink or laundry tub in a wet basement or near a swimming pool and the like 4 Object and Liquid Entry Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock Never spill liquid of any kind on the product 5 Attachments Do not use attachments not recommended by the manufacturer of this product as they may cause hazards 6 Cleaning Unplug this product from the wall outlet before cleaning Do not use liquid cleaners or aerosol cleaners Use a damp cloth for cleaning 7 Heat The product should be situated away from heat sources such as radiators heat registers stoves or other products including amplifiers that produce heat SERVICING 1 Servicing If your product is not operating correctly or exhibits a marked change in performance and you are unable to restore normal operation by following the detailed procedure in its operating instructions do n
16. NTINUED ON NEXT PAGE Tuner Setting Turn on the VCR and TV and select the VCR channel or AV mode Setting channels automatically Auto Channel Set Perform Auto Channel Set only if channels have not been set correctly by the Plug amp Play setting El Access Main Menu screen then Tuner Set screen Press MENU on the Remote Press AV to move the highlight bar arrow to TUNER SET then press OK or gt FA Perform Auto Channel Set Press AV to move the highlight bar arrow to AUTO CHANNEL SET then press OK or D The VCR selects the correct band TV or CATV automatically during Auto Channel Set When Auto Channel Set is complete SCAN COMPLETED appears on screen If the scan was unsuccessful SCAN COMPLETED NO SIGNAL appears on screen Check the connections and start again Press MENU to return to normal screen MAIN MENU FUNCTION SET TUNER SET INITIAL SET PRESS a v THEN OK PRESS MENU TO END TUNER SET BAND CATV AUTO CHANNEL SET MANUAL CHANNEL SET SELECT WITH 4 AND OK PRESS MENU TO END AUTO CHANNEL SET SCANNING PRESS MENU TO END Setting channels manually Manual Channel Set You can add the channels you want or delete the channels you do not want manually El Access Main Menu screen then Tuner Set screen Shee MAIN MENU Press MENU on the Remote Press AV to INITIALSET move the highlight bar arrow to TUNER S
17. Remote so that the VCR mode indicator lights on the display panel to view the program to be recorded El Set tape speed Press SP EP The selected tape speed will appear on the TV screen NOTE You can select tape speed in the stop mode or during recording pause mode El Start recording On the VCR press REC Or on the Remote while holding REC press PLAY P NOTE If VIDEO CALIBRATION is set to ON F pg 11 default setting the VCR takes about 7 seconds to assess the quality of the tape in use then recording begins with the picture level optimized During recording Pause recording Press PAUSE Hl Press PLAY B gt to resume recording You can select channel in the recording pause mode Stop recording Press STOP W on the Remote NOTE If the tape reaches its end during recording the recording stops and and on the display panel blink Press STOP EJECT amp on the VCR to eject the cassette or press REW lt 4 lt 4 on the Remote to rewind the tape OR Press STOP EJECT Ml 4 on the VCR Recording Features Turn on the VCR and TV and select the VCR channel or AV mode Specifying recording length Instant Timer Recording ITR During recording press REC on the VCR repeatedly until the recording length you want appears on the display panel The record indicator O on the display panel starts blinking Each time you press the
18. SVG fS LPT0730 001A COPYRIGHT 2002 VICTOR COMPANY OF JAPAN LTD Dear Customer Thank you for purchasing the JVC S VHS video cassette recorder Before use please read the safety information and precautions to ensure safe use of your new VCR CAUTIONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance SVIS Super VHS ET hiro INSTRUCTIONS Printed in China US Ve 1102 MNV PJ BJ NOTE Change or modifications not approved by the party responsible for compliance could void the user s authority to operate the equipment This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installa
19. Y TIME PHONE NUMBER WARRANTY REPAIR REPLACEMENT FORM REASON FOR RETURN Please do not return your product to the retailer Instead please box the product carefully preferably in the original carton and ship insured to the JVC repair replacement facility nearest you A COPY OF YOUR BILL OF SALE A COMPLETED WARRANTY REPAIR REPLACEMENT FORM AND ALL OF THE ORIGINAL ACCESSORIES WHICH CAME WITH YOUR UNIT MUST ACCOMPANY THE PRODUCT TO BE ELIGIBLE FOR REPAIR REPLACEMENT UNDER WARRANTY To obtain the address of the location nearest you please call 800 537 5722 or visit our website http www jvc com If you have any questions concerning your JVC Product please contact our Customer Relations Department at 800 252 5722 FOR SERVICING Only in U S A HOW TO LOCATE YOUR JVC SERVICE CENTER TOLL FREE 1 800 537 5722 http www jvc com Dear Customer In order to receive the most satisfaction from your purchase please read the instruction booklet before operating the unit In the event that repair is necessary or for the address nearest your location within the Continental United States please call 1 800 537 5722 for your nearest authorized servicer or visit our website at www JVC com Remember to retain your Bill of Sale for Warranty Service JVC JVC SERVICE amp ENGINEERING COMPANY OF AMERICA DIVISION OF JVC AMERICAS CORP Sophisticated electronic products may require oc
20. ace the VCR at least 20 cm 7 or 8 inch away from a TV DO NOT place the VCR close to a TV as it may cause noise picture disturbance or malfunctions power off etc to occur Buttons Connectors and Indicators Front Panel STOP EJECT H A S VIDEO input connector Cassette loading slot PAUSE VIDEO AUDIO input CH connectors sensor POWER FFe O CH CH Display panel Timer mode indicator VCR mode Play indicator indicator S VHS Record indicator indicator Channel and auxiliary input Clock time Rear Panel S VIDEO OUT AC a cord T IN 4 AUDIO VIDEO OUT TV OUT Remote POWER TV POWER we a A MONITOR TV PUT Lp met ane TVIVCR AMONITOR Dispos eg r _ gt DISPLAY TH D eC Number keys START G O a STOP DATE DATE 8 LA JE 5 C5 o 6 DAILY M F se et lt lt WEE i EL eEKLy STOP A i AUX CRESET ee RESET a ec el 3 TIMER SP EP Proc Eee SP EP SEARCH PROG ee a SEARCH PROG CHECK ev PLAY FF n 4 B ka Te E PAUSE CHA v 0 9 TV VOL Kd PID i ae ENTER OSD ENTER OSD JVC On screen display If you press OSD OK on the Remote when SUPERIMPOSE is set to ON pg 12 you can see the current VCR status on the TV screen The indications are not recorded even if the VCR is in the recording mode Channel and VCR operation auxiliary in
21. ated Do not recharge disassemble heat above 100 C or incinerate Replace battery with CR2032 Panasonic Matsushita Electric or Maxell is recommended Danger of explosion or Risk of fire if the battery is incorrectly replaced m Dispose of used battery promptly m Keep away from children m Do not disassemble and do not dispose of in fire Note to CATV system installer This reminder is provided to call the CATV system installers attention to Article 820 40 of the NEC that provides guidelines for proper grounding and in particular specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical Declaration of Conformity Model Number HR S2902U Trade Name JVC Responsible Party JVC Americas Corp Address 1700 Valley Road Wayne N J 07470 Telephone Number 973 317 5000 This device complies with Part 15 of FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Failure to heed the following precautions may result in damage to the VCR Remote or video cassette 1 DO NOT place the VCR 1N an environment prone to extreme temperatures or humidity in direct sunlight in a dusty environment in an environment where strong magnetic fie
22. button recording length increases in 30 minute intervals up to 6 hours The VCR shuts off after recording is finished To cancel an ITR press STOP MM on the Remote or STOP EJECT W on the VCR Watching one program while recording another During recording if you connect the TV and the VCR only using the RF connection pg 5 to view pictures from the VCR press TV VCR on the Remote so that VCR mode indicator goes off from the display panel The TV broadcast being recorded disappears If you are using the AV connection or S video connection C pg 5 to view pictures from the VCR change the TV s input mode from AV to TV Then select the channel you want to watch on theTV Second Audio Recording This VCR s built in MTS decoder enables reception of Multichannel TV Sound broadcast To record a SAP program received set 2ND AUDIO RECORD to ON F pg 12 S VHS Super VHS S VHS ET or VHS Recording Mode This VCR can record in S VHS Super VHS S VHS ET or VHS To record in S VHS Set S VHS MODE to ON F pg 12 Then insert a cassette marked S VHS The S VHS indicator lights up on the display panel The S VHS recording mode is selected To record in S VHS ET ona VHS cassette Set S VHS ET to ON pg 11 Then insert a cassette marked VHS The S VHS indicator lights up on the front display panel To record in VHS Insert a cassette marked
23. casional service Just as quality is a keyword in the engineering and production of the wide array of JVC products service is the key to maintaining the high level performance for which JVC is world famous The JVC service and engineering organization stands behind our products NATIONAL HEADQUARTERS JVC SERVICE amp ENGINEERING COMPANY OF AMERICA DIVISION OF JVC AMERICAS CORP 10 New Maple Avenue Pine Brook NJ 07058 9641 ACCESSORIES Don t service the product yourself To purchase accessories for your JVC product you CAUTION may contact your local JVC Dealer To prevent electrical shock do not open the cabinet From the 48 Continental United States call toll free There are no user serviceable parts inside 1 800 882 2345 or on the web at ww JVC com Please refer to qualified service personnel for repairs A236
24. ctric shock 4 Power Cord Protection Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to cords at plugs convenience receptacles and the point where they exit from the product 5 Ventilation Slots and openings in the cabinet are provided for ventilation To ensure reliable operation of the product and to protect it from overheating these openings must not be blocked or covered Do not block the openings by placing the product on a bed sofa rug or other similar surface Do not place the product in a built in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer s instructions have been adhered to 6 Wall or Ceiling Mounting The product should be mounted to a wall or ceiling only as recommended by the manufacturer ANTENNA INSTALLATION INSTRUCTIONS 1 Outdoor Antenna Grounding If an outside antenna or cable system is connected to the product be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built up static charges Article 810 of the National Electrical Code ANSI NFPA 70 provides information with regard to proper grounding of the mast and supporting structure grounding of the lead in wire to an antenna discharge unit size of grounding connectors location of antenna discharge unit connection to grounding elec
25. e mixed and played back NOTES While playing back a monaural tape sounds on the normal track will be heard regardless of this setting If RF connection F pg 5 is used for viewing pictures on the TV sound will be monaural even though you select HI FI You can also use the AMONITOR button on the Remote to select the desired monitor sound pg 8 E S VHS MODE ON OFF You can determine which recording mode either S VHS mode or VHS mode is used for recording on S VHS tapes When this function is set to ON you can record on S VHS tapes with S VHS picture quality When this function is set to OFF you can record on S VHS tapes with VHS picture quality NOTES S VHS mode allows you to make high quality video recordings with horizontal resolution of 400 lines comparing with the 230 lines of resolution of conventional VHS recordings To achieve the highest quality picture we recommended to record in S VHS mode But remember that a conventional VHS VCR without SQPB cannot play back S VHS tapes recorded in S VHS mode S VHS MODE setting does not affect recording on VHS tapes Recording on VHS tapes is always performed in VHS mode except when using S VHS ET mode pg 11 E FRONT AUX INPUT VIDEO S VIDEO You have to select which terminal either VIDEO composite or S VIDEO Y C separate signals to use as the video input terminal on the front panel Make sure you selec
26. er on the on screen display is reset automatically If the cassette s record safety tab has been removed playback begins automatically PA Start playback Press PLAY P The S VHS indicator lights up when you play back a tape recorded in S VHS mode or in S VHS ET mode F pg 9 During playback Stop playback Press STOP W on the Remote OR Press STOP EJECT Ml amp on the VCR Pause playback and view still picture Press PAUSE II Press PLAY P to resume normal playback NOTE During still picture vertical vibration may appear on the TV screen Press CHA Y on the Remote to get a clearer picture Pause and Frame by Frame playback Press PAUSE Il to pause then press ka a or gt or PAUSE II repeatedly Press PLAY P to resume normal playback Picture Search Press REW lt lt or FF BB Press REW lt 4 lt 4 or FF BP again to perform high speed search Each time you press REW lt lt or FF gt the search speed changes between low speed and high speed Press PLAY B gt to resume normal playback Press kad or BPI repeatedly Press PLAY P to resume normal playback Each time you press kad or gt l the playback speed changes To decrease the speed during picture search press the opposite direction button repeatedly During still picture press and hold BPI to start forward or Had to start reverse slow motion playback When you release the button still
27. ers Record Pause mode Press PLAY B gt to start recording nm E PICTURE CONTROL AUTO NORM EDIT SOFT SHARP This function helps you to adjust the playback picture quality according to your preference AUTO NORM Normally select this Picture quality is adjusted automatically When VIDEO CALIBRATION is OFF NORM will appear instead of AUTO EDIT Minimizes picture degradation during editing recording and playback SOFT Reduces image coarseness when viewing overplayed tapes containing much noise SHARP Clearer sharper edged picture when viewing images with much flat same colored surfaces such as cartoons NOTE Select EDIT when you are editing tapes After you finish editing the tapes select AUTO E AUTO TIMER ON OFF When this function is set to ON The timer recording standby mode is automatically engaged when the VCR is turned off It is temporarily canceled when the VCR is turned on You do not have to press TIMER to engage or disengage the timer recording standby mode When this function is set to OFF You have to press TIMER to engage or disengage the timer recording standby mode CONTINUED ON NEXT PAGE ee i E SUPERIMPOSE ON OFF When this function is set to ON various VCR status information on screen display appears on the screen NOTE When you use this VCR as the playback VCR for editing a tape be sure to s
28. et this function to OFF otherwise the VCR status information on screen display will be recorded on the edited tape AUTO SP EP TIMER ON OFF When this function is set to ON the VCR automatically switches to EP mode to allow complete recording if there is not enough tape to record the entire program while timer recording in SP mode For Example Recording a program of 140 minutes in length onto a 120 minute tape Approximately 110 minutes Approximately 30 minutes SP mode EP mode NOTES If you have programed the VCR to timer record 2 or more programs do not use this function but change the tape speed manually during timer programing There may be some noise and sound disturbance where the tape speed switches from SP to EP mode on the tape This function is not available during ITR Instant Timer Recording and will not work properly on the following tapes T ST 30 T ST 60 T ST 90 and T ST 120 E VIDEO STABILIZER ON OFF When this function is set to ON you can automatically correct vertical vibrations in the picture when playing back unstable recordings made on another VCR NOTE To watch recordings with close caption or when you finish viewing a tape set this function to OFF E BLUE BACK ON OFF When this function is set to ON the TV screen becomes all blue when receiving a channel not in use NOTE When you want to receive an unstable channel with p
29. et to ON s C pg 12 and DISPLAY on the Remote is pressed time counter and tape remaining time will appear on the TV screen To reset the time counter press C RESET on the Remote Function settings You can use the other useful function settings on the Function Set screen Turn on the VCR and TV and select the VCR channel or AV mode El Access Main Menu screen then Function Set screen Press MENU on the Remote Press AV to move the highlight bar arrow to FUNCTION SET then press OK or gt FA Select Function Press AV to move the highlight bar arrow to the function you want to set MAIN MENU FUNCTION SET TUNER SET INITIAL SET PRESS 4 HEN O PRESS MENU TO END PREVIOUS PAGE VIDEO STABILIZER OFF VIDEO CALIBRATION BLUE BACK ON PICTURE CONTROL 2ND AUDIO RECORD OFF AUTO TIMER AUDIO MONITOR HI FI SUPERIMPOSE ON S VHS MODE ON AUTO SP EP TIMER OFF FRONT AUX INPUT VIDEO NEXT PAGE FUNCTION gt S VHS ET SELECT WITH Av AND OK PRESS MENU TO END SELECT WITH aw AND OK PRESS MENU TO END E Change setting Press OK or The default setting is bold in the table below Press MENU to return to normal screen After a power failure occurs some Function Settings will be reset to its default setting E S VHS ET ON OFF When this function is set to ON you can record on VHS cassettes with S VHS picture quality Tapes recorded using this fu
30. h timer program you have made will start at its start time unless its end time has elapsed If the tape reaches its end during timer recording the recording stops and O and on the display panel blink Press TIMER to disengage timer then press STOP EJECT amp on the VCR to eject the cassette or press POWER then press REW lt lt 4 to rewind the tape VCR has auto timer feature F pg 11 Express Timer Programing Load a cassette with the record safety tab intact The VCR turns on and the counter is reset automatically Hl Press PROG on the Remote to access the Program screen A Press START Number key uge PROGRAM 1 and or 4 STOP Number key start st P 2 and or 5 DATE Number key 3 and or 6 or CH repeatedly to enter the start time stop time date or channel Press and hold START or STOP to increase the time in 30 minute intervals To set the tape speed press SP EP To timer record daily Monday Friday or weekly serials press DAILY M F Number key 8 or WEEKLY Number key 9 Pressing the button again makes the DAILY or WEEKLY display disappear E Press OK or PROG If PROGRAM NOT COMPLETED PROGRAM OVERLAP appears see Program overlap warning display F pg 10 El Press TIMER The VCR turns off automatically and is displayed on the display panel H To stop timer rec
31. l Set F pg 7 E Set VCR channel The VCR channel is the channel on which you can watch the picture from the VCR on the TV when only using the RF connection With no tape in the VCR press POWER to turn off the VCR then press STOP EJECT W 4 on the VCR for more than 5 seconds CH3 appears on the display panel Press CHA V on the Remote to select CH3 CH4 or CH OFF then press OK The VCR channel is preset to CH3 Set to CH4 if CH3 is used for broadcasting in your area EJ Final preparation for use Turn on the VCR and the TV and select the VCR channel 3 or 4 or AV mode on the TV You can now perform basic playback or basic recording If you connect the TV and the VCR only using the RF connection press TV VCR on the Remote so that the VCR mode indicator lights on the display panel Initial Settings Language Setting The default setting is ENGLISH Turn on the VCR and TV and select the VCR channel or AV mode El Access Main Menu screen then Initial Set screen MAIN MENU FUNCTION SET TUNER SET Press MENU on the Remote Press AV to move the highlight bar arrow to INITIAL SET then press OK or gt PRESS ar THEN OK MENU TO END PRESS A Select language INITIAL SET This VCR offers you the language choice to ctock set view menus and some messages in English Spanish or French Press AV to move the highlight bar arrow
32. l the safety and operating instructions before you operate this product and keep this booklet for future reference INSTALLATION 1 Grounding or Polarization A Your product may be equipped with a polarized alternating current line plug a plug having one blade wider than the other This plug will fit into the power outlet only one way This is a safety feature If you are unable to insert the plug fully into the outlet try reversing the plug If the plug should still fail to fit contact your electrician to replace your obsolete outlet Do not defeat the safety purpose of the polarized plug B Your product may be equipped with a 3 wire grounding type plug a plug having a third grounding pin This plug will only fit into a grounding type power outlet This is a safety feature If you are unable to insert the plug into the outlet contact your electrician to replace your obsolete outlet Do not defeat the safety purpose of the grounding type plug 2 Power Sources Operate your product only from the type of power source indicated on the marking label If you are not sure of the type of power supply to your home consult your product dealer or local power company If your product is intended to operate from battery power or other sources refer to the operating instructions 3 Overloading Do not overload wall outlets extension cords or integral convenience receptacles as this can result in a risk of fire or ele
33. layback press STOP MM on the Remote or STOP EJECT Ml 4 on the VCR Locating beginning of recordings Index Search When recording on this VCR index codes are placed on the tape at the beginning of each recording E While the tape is not running press Kd or gt on the Remote to start search H To access a recording of 2 to 9 index codes away press lt lt or P repeatedly until the correct number is displayed on the screen only if SUPERIMPOSE is set to ON C pg 12 Playback begins automatically when the desired recording is located Beginning of the _ Current Beginning of the current program position on 2nd next program recorded the tape recorded Previous Next program program 2nd next recorded recorded 2 a 1 2 3 _ i gt gt _ Locating beginning of timer recordings Instant Review After ensuring that the VCR is turned off and that the timer mode is disengaged press REVIEW The VCR turns on and rewinds to the index code indicating the beginning of the last timer recorded program then begins playback automatically You can access a program of 2 to 9 index codes away from the current position on the tape If for example you have 5 programs recorded and you want to watch the third one press REVIEW three times The Instant Review function will also operate if the VCR is turned on Skipping unwanted portions Skip Search Press SKIP SEARCH o
34. lds are generated on a surface that is unstable or subject to vibration 2 DO NOT block the VCR s ventilation openings 3 DO NOT place heavy objects on the VCR or on the Remote 4 DO NOT place anything which might spill on the top of the VCR or on the Remote 5 AVOID violent shocks to the VCR during transport For Customer Use Enter below the Model No and Serial No which are located on the rear of cabinet Retain this information for future reference Model No Serial No SVHS regj Cassettes marked S VHS and VHS can be used with this video cassette recorder However S VHS recordings are possible only with cassettes marked S VHS By using S VHS ET it is possible to record and play back with S VHS picture quality on VHS cassettes with this VCR As an ENERGY STAR Partner JVC has determined that this product or product model meets the ENERGY STAR guidelines for energy efficiency IMPORTANT PRODUCT SAFETY INSTRUCTIONS Electrical energy can perform many useful functions But improper use can result in potential electrical shock or fire hazards This product has been engineered and manufactured to assure your personal safety In order not to defeat the built in safeguards observe the following basic rules for its installation use and servicing ATTENTION Follow and obey all warnings and instructions marked on your product and its operating instructions For your safety please read al
35. ly by the clock setting data transmitted from one of the regular TV broadcast channels We call this TV channel the host channel and it is a PBS channel in your area ATTENTION If you use a cable box Plug amp Play will not function set the clock and tuner channels separately I pg 6 7 Depending on areas or reception conditions the VCR may not receive the Auto clock setting data from a PBS channel If this function is taking a considerable amount of time it may be necessary to perform the procedure in Semiauto Clock Set C pg 6 or Manual Clock Set F pg 6 ra During Initial Auto Clock Set M UE Aut blinks Zi SS v un During Auto Channel Set ILI The channel numbers are displayed as they are scanned and set Plug amp Play Completed The current time is displayed co Ca Z3 z What to do if Plug amp Play setting failed If an incorrect time is displayed on the display panel perform the procedure in Semiauto Clock Set F pg 6 or Manual Clock Set lt pg 6 if appears on the display panel ensure that the antenna cable is connected correctly Then turn on and off the VCR the Plug amp Play setting will be automatically reactivated If Plug amp Play setting is not performed though the antenna cable is connected correctly perform the procedure in Manual Clock Set C pg 6 and Auto Channel Set C pg 7 or Manual Channe
36. n the Remote once to 4 times during playback Each press initiates a 30 second period of high speed playback up to 2 minutes When the specified portion of the tape is skipped normal playback resumes automatically To return to normal playback during Skip Search press PLAY B gt f Recording It may be unlawful to record or play back copyrighted material without the consent of the copyright owner Accidental erasure prevention To prevent accidental recording on a recorded cassette remove its record safety tab To record on it later cover the hole with adhesive tape Record safety tab Basic Recording Turn on the VCR and TV and select the VCR channel or AV mode E Load a cassette Make sure the record safety tab is intact If not cover the hole with adhesive tape before inserting the cassette The VCR turns on and the counter on the on screen display is reset automatically FA Select recording channel On the Remote Press CHA V or the Number keys On the VCR Press PAUSE CH The channel display on the Ly S display panel starts blinking While the display is um blinking press FF CH or REW CH to select a channel After about 5 seconds the channel display bd stops blinking SS NOTES pale You can select channel in the stop mode recording pause mode or during rewind fast forward 4 0 If you connect the TV and the VCR only using the RF connection press TV VCR on the
37. nction can be played back on most of S VHS VCRs or VHS VCRs equipped with the SQPB S VHS QUASI PLAYBACK function When this function is set to ON the S VHS indicator lights up on the display panel NOTES Before recording set VIDEO CALIBRATION to ON See below You cannot activate the S VHS ET function while recording timer recording or Instant Timer Recording F pg 9 or the VIDEO CALIBRATION function t See below is in progress The S VHS ET function does not work with S VHS cassettes To keep the highest quality recording and playback pictures over a long period of time S VHS recording on S VHS cassettes is recommended e Use of high grade tapes is recommended for S VHS ET recordings On some tapes picture quality will not improve even if the S VHS ET function is used Check the recording quality before you start important recordings E VIDEO CALIBRATION ON OFF When this function is set to ON this VCR checks the condition of the tape in use during playback and recording and compensates to provide the highest possible pictures This takes place whenever you play back a tape or start recording after inserting a tape NOTE The VCR checks the tape condition for about 7 seconds then starts recording To make sure you record the desired scene or program completely perform the following steps Press and hold PAUSE Ill and press REC After about 7 seconds the VCR re ent
38. o return to normal screen Turn off the VCR Aut will appear on the display panel while the clock is being set The current clock time will appear automatically when the clock setting is complete Selections of host channel and D S T mode will be reset to AUTO after a power failure occurs Setting clock manually Manual Clock Set First follow steps Hl to H in Preparations above then go to the following steps El Set time date and year CLOCK SET Press AV until the desired time appears YME arra EAE then press OK or gt Set the date and year AUTO CLOCK ON HOST CH auTO CATV in the same way DST TIMEZONE AUTO Holding AV changes the time in 30 minute intervals or changes the date in 15 day intervals A Select D S T mode CLOCK SET Press OK or gt to move the highlight bar to TIME ppg DATE YEAR ii D S T then press AV to select the AUTO CLOCK OFF desired setting DST ON Adjustment will be made by the built in clock itself OFF Select when Daylight Saving Time does not apply to you El Start clock Press MENU and normal screen appears PRESS 4 THEN OK PRESS MENU TO END PRESS 4 7 THEN OK PRESS MENU TO END To make corrections any time during the process Press OK or gt repeatedly until the item you want to change blinks then press AV Manual setting of the clock will be lost after a power failure occurs CO
39. omatic tracking Selecting monitor sound Audio Monitor While playing back a tape on which stereo sound or SAP sound is recorded press AAMONITOR on the Remote Each time you press the button sound changes HI FI Normally select this Hi Fi sound is played back HI FI L Sound on the left Hi Fi channel is played back HI FI R Sound on the right Hi Fi channel is played back NORM Sound on the normal track is played back NORM HI FI Both sounds on the Hi Fi track and normal track are mixed and played back NOTE The above indication appears when SUPERIMPOSE is set to ON F pg 12 though the monitor sound changes in sequence Automatic operations after rewinding Next Function Memory The Next Function Memory tells the VCR what to do after rewinding is complete Ensure that the VCR is in stop mode For Automatic Playback Start Press REW lt then press PLAY P within 2 seconds For Automatic Power Off Press REW lt then press POWER O I within 2 seconds For Automatic Timer Standby Press REW lt lt then press TIMER within 2 seconds NOTE It is not possible to select the Automatic Timer Standby function if the cassette s record safety tab is removed Playing back tape repeatedly 100 times Repeat Play During playback press and hold PLAY B gt for more than 5 seconds The play indicator E gt on the display panel starts blinking slowly To stop p
40. oor signals set this function to OFF E 2ND AUDIO RECORD ON OFF When this function is set to ON If a SAP program is received the SAP audio is recorded on both the normal and Hi Fi tracks The main audio is not recorded If a non SAP program is received the main audio is recorded on both the Hi Fi and normal tracks When this function is set to OFF the SAP audio cannot be recorded NOTES When the channel is changed on the VCR The STEREO indication appears on the screen for about 5 seconds if the program is a stereo broadcast The SAP indication appears on the screen for about 5 seconds if the program is a SAP broadcast Both indications appear when a stereo program is accompanied by SAP sound E AUDIO MONITOR HI FI HI FI L HI Fl R NORM MIX This VCR can record two sound tracks simultaneously normal and Hi Fi on a Hi Fi stereo tape You can select the sound track s to listen to while playing back a Hi Fi stereo tape In addition when playing back a prerecorded tape containing two separate audio programs on the Hi Fi tracks you can choose either one by selecting either HI FI L or HI FI R HI FI Normally select this Hi Fi sound is played back HI FI L Sound on the left Hi Fi channel is played back HI FI R Sound on the right Hi Fi channel is played back NORM Sound on the normal track is played back MIX Both sounds on the Hi Fi track and normal track ar
41. ording press TIMER then STOP ll PRESS SP EP 8 DAILY 9 WEEKLY THEN OK PRESS PROG TO END To use the VCR while it is in timer recording standby mode Press TIMER then press POWER W After you use the VCR press TIMER again to put the VCR into timer recording standby mode Checking canceling or changing program settings El Disengage timer Press TIMER then press POWER 0 1 When AUTO TIMER is set to ON pg 11 you do not have to press TIMER FA Access Program Check screen Press PROG CHECK EJ Access Program screen Press PROG CHECK again Each time you press PROG CHECK the next program s Program screen appears Ei Cancel or change program setting To cancel a program press CANCEL when the Program screen you do not want is shown To change a program press the appropriate button START Number key 1 and or 4 STOP Number key 2 and or 5 DATE Number key 3 and or 6 CH 6 DAILY M F Number key 8 WEEKLY Number key 9 and or SP EP when the Program screen on which you want to make changes is shown R START STOP CH 8 00P 10 00 12 10 00A 10 45 40 11 30P 1 00 125 PI 1 2 3 4 5 6 7 8 PRESS CHECK TO NEXT 5 Return to normal screen Press PROG CHECK repeatedly until no Program screen is shown EJ Reengage timer recording standby mode Press TIMER The VCR turns off automatically and
42. ot attempt to service it yourself as opening or removing covers may expose you to dangerous voltage or other hazards Refer all servicing to qualified service personnel 2 Damage Requiring Service Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions a When the power supply cord or plug is damaged b If liquid has been spilled or objects have fallen into the product c If the product has been exposed to rain or water d If the product does not operate normally by following the operating instructions Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation e If the product has been dropped or damaged in any way f When the product exhibits a distinct change in performance this indicates a need for service 3 Replacement Parts When replacement parts are required be sure the service technician has used replacement parts specified by the manufacturer or which have the same characteristics as the original part Unauthorized substitutions may result in fire electric shock or other hazards 4 Safety Check Upon completion of any service or repairs to this product ask the service technician to perform safety checks to determine that the product is in safe operating
43. put Timer warning display mode Day and l clock time THU 12 00 AM PAUSEJ F sterco f STEREO WARNING Co SP Tape spee program SAP O START S Lo Cassette mark indication P CANCEL SAP B font H Tape position indication J Audio Neem REMAIN monitor HI FI COUNT INDEX indications RECORD ER 10 00 Index number 1 23 BN Tape remaining time Time counter To recall an indication Press OSD OK All indications corresponding to the current status are displayed for 5 seconds After that the counter information and RECORD PAUSE if in the Record Pause mode are left displayed on the screen Press OSD OK again to clear the display The RECORD PAUSE indication is left displayed on the screen nm Connections and Plug amp Play Setting El Check contents Make sure the package contains all of the accessories listed in Specifications F pg 14 FA Situate VCR Place the VCR on a stable horizontal surface EJ Connect VCR to TV Antenna or cable A Coaxial cable Flat feeder Matching transformer not supplied AC power cord L Back of VCR AC outlet To audio video input connectors Audio video cable not supplied To 75 Q terminal Ti To S video input connector RF cable supplied S video cable not supplied RF Connection
44. t the correct terminal otherwise you may fail in recording editing on this VCR Child Lock Turn on the VCR and TV and select the VCR channel or AV mode You can disable the VCR operations While the VCR is turned on press and hold POWER 0 on the Remote for more than 10 seconds The VCR turns off CL appears for about 5 seconds on the display panel To release the child lock press and hold POWER I on the Remote until the VCR turns on NOTES Pressing TIMER during timer recording unplugging the AC power cord or a power outage also releases the child lock Even if the child lock function is in use it is possible to engage and disengage the timer mode with TIMER on the Remote Keep the Remote out of the children s reach Timer recording programs will be performed even if the child lock function is activated es Editing You can use your VCR as the playback or recording VCR You can use a camcorder as the playback VCR and your VCR as the recording VCR Refer also to the other components instruction manuals for connection and its operations EE Make connections Example 1 When another VCR is VHS VCR This VCR To AUDIO VIDEO IN To AUDIO VIDEO OUT When using this VCR as the recording VCR connect this VCR s AUDIO VIDEO IN connectors to the When using this VCR as the playback VCR connect this VCR s AUDIO VIDEO OUT connectors to the audio video input connectors on
45. tion This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help WARNING TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE CAUTION This video cassette recorder should be used with AC 120V 60Hz only To prevent electric shocks and fire hazards DO NOT use any other power source CAUTION TO PREVENT ELECTRIC SHOCK MATCH WIDE BLADE OF PLUG TO WIDE SLOT FULLY INSERT ATTENTION POUR EVITER LES CHOCS ELECTRIQUES INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU AU FOND Caution on Replaceable lithium battery The battery used in this device may present a fire or chemical burn hazard if mistre
46. trodes and requirements for the grounding electrode 2 Lightning For added protection for this product during a lightning storm or when it is left unattended and unused for long periods of time unplug it from the wall outlet and disconnect the antenna or cable system This will prevent damage to the product due to lightning and power line surges 3 Power Lines An outside antenna system should not be located in the vicinity of 1 ANTENNA overhead power lines or LERON WIRE other electric light or power circuits or where it can fall into such Fe ANTENNA UNE power lines or circuits M When installing an EQUIPMENT outside antenna system CEN NC Ne extreme care should be EE SEETION 10 taken to keep from BROUND CUAMES touching such power NECART 50 PART pp PING ELECTRODE SYSTEM lines or circuits as contact with them might be fatal USE 1 Accessories To avoid personal injury Do not place this product on an unstable cart stand tripod bracket or table It may fall causing serious injury to a child or adult and serious damage to the product Use only with a cart stand tripod bracket or table recommended by the manufacturer or sold with the product Use a mounting accessory recommended by the manufacturer and follow the manufacturer s instructions for any mounting of the product Do not try to roll a cart with small casters across thresholds or deep pile carpets EXAMPLE OF ANTENNA GROUNDING AS PER NAT
47. y 3 and or 6 CH 6 DAILY M F Number key 8 WEEKLY Number key 9 and or SP EP when the Program screen on which you want to make changes is shown then press OK or gt if the overlap is not yet solved the conflicting programs will be shown on the Program check screen Repeat the above steps again OK TO CONFIRM PROG TO END a o as f Other Functions Timer warning display A warning appears on the TV screen to tell you that the timer recording is to start in 5 minutes if you are not in the timer recording standby mode at that time Press TIMER to put the VCR into timer recording standby mode To clear the display press CANCEL on the Remote WARNING TIMER RECORDING TO START SOON CANCEL Checking tape position When you change the VCR operation mode from the stop mode to fast forward or rewind mode or when you perform an Index Search or Instant Review the tape REMAIN 1 00 wae COUNT 1 23 45 position indicator appears The position of F in relation to B Beginning or E End shows you where you are on the tape Set SUPERIMPOSE to ON F pg 12 gt gt B B E Changing display information Each time you press DISPLAY the display panel shows the channel number and the clock time alternatively You can change display in the stop or recording mode or during rewind fast forward Ao When SUPERIMPOSE is s
Download Pdf Manuals
Related Search