JVC TM-2003U User's Manual
Contents
1. Diagram 3 TV Rear Panel Output BNC Connector Box TV Rear Panel 7 e IN VIDEOS 750 o VHF UHF E D u mono il OUT AUDIO co VCR Coaxial Cables Connecting to A DVD Player You can connect a DVD player instead of a VCR as illustrated in Diagram 2 on page 12 or Diagram 3 above TV Rear Panel BNC Connector Box PEN TV Rear Panel 7 o vo on IN o FHF Umorno Tl OUT AUDIO R ll e You must connect the video cable from the DVD player to the BNC connector box in order for it to work e Please consult the user s manual for your DVD player for more information on how to hook it up properly e Progressive DVD players players with an output scan of 31 5 KHz will not work properly with this television Set your DVD player s output to interlaced or non progressive mode Quick Setup Connections Connecting to an External Amplifier TV Rear Panel Speaker Speaker Amplifier 1 Connect a white composite cable from the LEFT AUDIO OUTPUT on the back of the TV to the LEFT AUDIO INPUT on the amplifier 2 Connect a red composite cable from the RIGHT AUDIO OUTPUT on the back of the TV to the RIGHT AUDIO INPUT on the amplifier Notes e Refer to your amplifier s manual for more information e You can use AUDIO OUTPUT for your home theater system Connecting to a Camcorder You may connect2. RETURN CHANNEL PROGRAMMED The channel currently active has been programmed as your return channel Now scan through the channels using the CHANNeEL buttons TY RETURN e To cancel your return channel press and hold the Return button for three seconds The message RETURN CHANNEL CANCELLED will appear e Return works only with the Channel buttons Pressing any number key will cancel return You will return to your programmed channel Turns the TV on or off TY Press the Power button Number Buttons 10Key Pad Use the number buttons on the remote control to move directly to a specific channel For example to move to channel 7 TY 0 Zero 7 Seven Channel Use these buttons to move up or down all the available channels your TV is able to recieve Volume Use these buttons to raise or lower the TV s volume level 100 Button Use the 100 button to directly access channels above channel 99 For example to move to channel 124 press 100 2 Two 4 Four Troubleshooting PROBLEMS There is no power See if the power cord became unplugged Check for a blown fuse or circuit breaker or a power outage There is no picture or sound Remote control is not operating properly or at all The antenna could be disconnected The input mode could be set improperly See page 35 The tuner Auto Tuner Setup could be set improperly See page 17 e The TV
3. Press the Menu button To CLOSED CAPTION To operate To select CAPTION TEXT or OFF To move to CAPTION or TEXT To select a caption CC1 to CC4 or text channel T1 to T4 To accept that selection and move to FINISH To save settings and exit MODE TEXT CAPTION CC1 CC2 CC3 CC4 TEXT gt T1 T2 T3 14 FINISH SELECT BY Mu OPERATE BY BO EXIT BY EXIT Closed caption subtitles are usually found on closed caption channel CC1 Some programs may include additional text information which is usually found on text channel T1 The other channels are available for future use Closed captioning may not work correctly if the signal being received is weak or if you are playing a video tape Most broadcasts containing closed captioning will display a notice at the start of the program Initial Setup Background This feature inserts either a black or clear background behind the onscreen menu displays Ey Press the Menu button AV To BACKGROUND BACKGROUND BLACK CLEAR lt gt To turn Set Background to BLACK or CLEAR P Exit when finished Button Functions The Menu button allows you to access JVC s onscreen menu system Press Menu to activate the onscreen menu system e See individual topics like Sound Adjust for specific information on using menus Use this button to enter or exit the TV s onscreen menus Display The display screen shows the current status of timers and inputs TY Press
4. TP Zero to lock or unlock that channel CP Exit when finished Channel Guard Message When a viewer attempts to watch a guarded channel the following message appears To watch a channel that you have locked enter THIS CHANNEL IS LOCKED BY the Lock Code using the 10 key pad CHANNEL GUARD If the wrong code is entered the message PLEASE ENTER LOCK CODE BY INVALID LOCK CODE will flash on the screen 10 KEY PAD TO UNLOCK IT The channel cannot be accessed until the correct NO code is entered Once a channel has been unlocked it will remain unlocked until the television is turned off e See also Set Lock Code page 26 Initial Setup V Chip Your TV is equipped with V Chip technology which enables TV Parental Guidelines for United States and Canada and Movie MPAA Guideline controls V Chip technology allows you to program your TV to receive or not to receive programs based on content according to the guidelines Programs which exceed the ratings limits you set will be blocked When a viewer attempts to watch a blocked channel this message appears The channel will remain blocked until the correct lock code is entered see page 26 for information THIS PROGRAMMING EXCEEDS on setting your lock code You can customize the YOUR RATING LIMITS V Chip settings of your television to match your PLEASE ENTER LOCK CODE BY personal tastes The V Chip menu below is the 10 KEY PAD TO UNLOCK IT starting point
5. TV set from the wall outlet and refer servicing to qualified service personnel under the following conditions A When the power cord or plug is damaged or frayed B If liquid has been spilled into the TV set C If the TV set has been exposed to rain or water D If the TV set does not operate normally by following the operating instructions Adjust only those controls that are covered in the operating instructions as improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the TV set to normal operation E If the TV set has been dropped or damaged in any way F When the TV set exhibits a distinct change in performance this indicates a need for service 16 Do not attempt to service this TV set yourself as opening or removing covers may expose you to dangerous voltage or other hazards Refer all servicing to qualified service personnel 17 When replacement parts are required have the service technician verify in writing that the replacement parts he uses have the same safety characteristics as the original parts Use of manufacturer s specified replacement parts can prevent fire shock or other hazards 18 Upon completion of any service or repairs to this TV set please ask the service technician to perform the safety check described in the manufacturer s service literature 19 When a TV set reaches the end of its useful life improper disposal could resu
6. for your V Chip settings NO You can use US V Chip settings for programming broadcast from the United States Canadian V CHIP ON OFF V Chip settings for programming broadcast from Canada E wore RAINES and movie ratings You may use any or all of the settings SET CANADIAN RATINGS ENG US V Chip Canada V Chip Movie ratings Descriptions SET CANADIAN RATINGS FRE UNRATED VIEW BLOCK FINISH for setting each of the three V Chip formats appear in the next seven pages along with descriptions of the rating categories SELECT BY Ot OPERATE BY KO EXIT BY EXI To access the rating categories Py Press the Menu button AV To V CHIP lt gt To operate Lock icon will appear Py Press Zero to access the V Chip menu lt gt To turn V Chip ON or OFF V Chip must be turned ON for rating settings to operate AV To move to SET US TV RATINGS SET MOVIE RATINGS or SET CANADIAN RATINGS see following pages for descriptions of each item Special Note about Ratings Some programs are not broadcast with a ratings signal Therefore even if you setup V Chip ratings limits these programs will not be blocked Parents are cautioned to preview the contents of these programs or movies Initial Setup US V Chip Ratings U S PARENTAL RATING SYSTEMS Programs with the following ratings are appropriate for children O TV Y is Appropriate for All Children Programs are created for very young viewers and shoul
7. lock icon to by pressing or gt again You may then select individual categories to block Initial Setup Setting Ratings with the V Chip Button To access Rating information about a certain program press the V ChiP button while viewing that program A display like this will appear PROGRAM IS RATED TV PG V If you decide you want to block this category of viewing press 0 while the above screen is visible and all programs from that category will be blocked Example 1 If you want to set your V Chip settings to block all programming above TV PG Py Press Zero when TV PG is displayed a A a V FV A s A aa A A A A D AA SELECT BY MU OPERATE BY HG EXIT BY Xi All Programming above TV PG will be blocked Example 2 If you want to set your V Chip settings to block all programming above a current setting such as TV PG V with violence TP Press Zero when TV PG V is displayed SELECT BY OM OPERATE BY KO EXIT BY ED All Programming above TV PG V with Violence will be blocked e For Children s programming you can block TV Y and Y7 programs by Pressing 0 when Y is displayed during a program Programming for audiences other than children s audiences will not be affected Initial Setup Movies Ratings O NR Not Rated This is a film which has no rating In many cases these films were imported from countries which do not
8. may precisely set your clock using the XDS time signal broadcast by most public broadcasting stations If you do not have this in your area you will have to set the clock manually See manual clock set below To set the clock using the XDS signal TY Press the Menu button AV To SET CLOCK lt gt To operate When you set the clock automatically choose AUTO by pressing the or gt arrows AV To TIME ZONE lt gt To select your time zone BODE AWO MANUAL AV To D S T daylight savings time TIME ZONE EASTERN lt gt To turn D S T ON or OFF D S T ON OFF vy To FINISH FINISH lt gt To save settings AV To move to the hour lt gt To set the hour AUTO MANUAL AV To move to minutes lt gt To set the minutes vy To START CLOCK START CLOCK lt gt To operate THANK YOU The Daylight Savings Time feature automatically adjusts your TV s clock for Daylight Savings The clock will move forward one hour at 2 00 am on the first Sunday in April The clock will move back one hour at 2 00 am on the last Sunday in October Notes e You will have to reset the clock after a power interruption You must set the clock before operating any timer functions Clock Timers On Off Timer The on off timer lets you program your television to turn itself on or off You can use it as an alarm to wake up to help you remember important programs or as a decoy when you re not home TY Press the Menu button AV
9. new television s many great features If you re anxious to start using your television right away a quick setup guide follows on the next few pages Quick Setup Diagrams NOTE Before you connect your television to another device please refer to the proper diagrams for your specific TV and remote These will help assist you in understanding how to connect your television to another device as well as use the remote to set up your television Rear Panel Diagram CONNECT THE BNC CONNECTOR BOX AUTO TERMINATION THIS VIDEOAN JACK RCA IS TERMINATED 75 W 750 VHF UHF O Front Panel Diagram MA INPUT 2 VIDEO aes L MONO 1D Quick Setup Remote Control O MENU HF VCR CONTROL CHANNEL POWER TV VCR on REW PLAY FF REC msToPp PAUSEM i EXIT JVC RM C205 TV RM C205 e For information on remote control buttons see pages 35 37 Quick Setup Getting Started Getting Started These quick setup pages will provide you in three easy steps with the basic information you need to begin using your new television right away If you have questions or for more detailed information on any of these steps please consult other sections of this manual Step 1 The Remote Control Before you can operate your remote control you first need to install the batteries included Raise the latch on the remote s back cover to remove Insert two batteries carefully no
10. provide some protection against voltage surges and built up static charges Section 810 of the National Electrical Code provides information with respect to proper grounding of the mast and supporting structure grounding of the lead in wire to an antenna discharge unit size of grounding conductors location of antenna discharge unit connection requirements for the grounding electrode 7 An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits or where it can fall into such power lines or circuits When installing an outside antenna system extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal a ANTENNA LEAD IN WIRE GROUND CLAMP ANTENNA DISCHARGE UNIT NEC SECTION 810 20 ELECTRICAL SERVICE EQUIPMENT GROUNDING CONDUCTORS NEC SECTION 810 21 425 GROUND CLAMPS _ POWER SERVICE GROUNDING ELECTRODE SYSTEM NEC NATIONAL ELECTRIC CODE NEC ARTICLE 250 PARTH EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE 8 TV sets are provided with ventilation openings in the cabinet to allow heat generated during operation to be released Therefore Never block the bottom ventilation slots of a portable TV set by placing it on a bed sofa rug etc Never place a TV set in a built in enclosure unless proper ventilation is provided Never
11. use the MPAA ratings system Other NR films may be from amateur producers who didn t intend to have their film widely released NR Not Rated Programming may contain all types of programming including children s programming foreign programs or adult material O G General Audience In the opinion of the review board these films contain nothing in the way of sexual content violence or language that would be unsuitable for audiences of any age O PG Parental Guidance Parental Guidance means the movie may contain some contents such as mild violence some brief nudity and strong language The contents are not deemed intense O PG 13 Parents Strongly Cautioned Parents with children under 13 are cautioned that the content of movies with this rating may include more explicit sexual language and violence content than movies rated PG O R Restricted These films contain material that is explicit in nature and is not recommended for unsupervised children under the age of 17 O NC 17 No One Under 17 These movies contain content which most parents would feel is too adult for their children to view Content can consist of strong language nudity violence and suggestive or explicit subject matter O X No One under 18 Inappropriate material for anyone under 18 Directions to set Movie MPAA Ratings TY Press the Menu button AV To V CHIP lt gt To operate Lock icon a appears Ty Press Zero to access V Chip setup op
12. you to change and adjust the way the picture appears on your television TINT Tint allows you to adjust the levels of red and green in your TV picture COLOR The color function lets you make all the colors in the TV picture appear either more vivid or subtle PICTURE Picture allows you to adjust the levels of black and white on the TV screen giving you a darker or brighter picture overall BRIGHT You can adjust the overall brightness of the TV picture with the Bright control DETAIL The Detail feature adjusts the level of fine detail displayed in the picture Adjust the Picture Settings TY Press the Menu button MR ena AY ToTINT COLOR PICTURE BRIGHT or cae cra AS DETAIL BRIGU e Le lt gt To enter DETAIL lt gt To adjust the setting AV To move to the next setting SELECT BY DM OPERATE BY BO EXIT BY EXD Noise Muting This feature inserts a blank blue screen over channels which are not broadcasting or are too weak to be received clearly TY Press the Menu button AV To NOISE MUTING lt gt To turn noise muting ON or OFF Note e Noise muting will not work during auto tuner setup or when you operate channel summary Picture Adjust Set Video Status With Set Video Status you can save your own set of picture quality adjustments as Choice and have access to them at the touch of a button TY Press the Menu button TINT AV T
13. A 35 A chee tae Smee sae iT 35 Display 35 Input 2 2 35 Video Status 36 Sleep Timer 36 Muting ss a se ete kA ea ws 36 VCR Buttons 36 Return soe ok ok RA oien 37 POWEP wola ha BA taht aos Ae 37 Number Buttons 10key Pad 37 Channel t 04 37 Volume o 37 TOO so se a a ei 37 Appendices Troubleshooting 38 Specifications 39 Quick Setup Unpacking Your TV Thank you for your purchase of a JVC Color Television Before you begin setting up your new television please check to make sure you have all of the following items In addition to this guide your television box should include 1 Television 1 Remote Control Two AA Batteries BNC Connection Box Once you have unpacked your television the next step is to connect it to your antenna cable or satellite system and to connect the audio video devices you want to use with your television To make these connections you will use plugs like the ones illustrated below Component Cables Coaxial Cables Composite Cables Ah Audio Cables Used to connect an external antenna or cable TV system to your Used to connect audio TV video devices like VCRs DVD players stereo amplifiers game consoles etc We recommend that before you start using your new television you read your entire User s Guide so you can learn about your
14. ME Used for when you are playing video games connected to your TV Ey Press the Vipeo Status button By every press of the video status button you change the mode Hed CHOICE gt GAME gt STANDARD ZA The Sleep Timer can turn the TV off for you after you fall asleep Program it to work in intervals of 15 minutes for a total time of up to 180 minutes Ty Press the SLEEP Timer button 9 15 30 45 60 75 90 105 120 135 150 165 180 gt Sleep Timer Message 20 seconds before the automatic shutoff this message will appear GOOD NIGHT PUSH SLEEP TIMER BUTTON TO EXTEND You then have 20 seconds to press the sleep timer button to delay the shut off for another 15 minutes The muting button instantly turns the volume down completely when you press it Press Mutinc and the volume level will instantly go to zero To restore the volume to its previous level press MurING again VCR Buttons You can use your remote control RM C205 to operate the basic functions of a JVC brand VCR These functions include play record rewind fast forward stop pause channel scan TV VCR power on and power off Button Functions The return button has two functions Return Returns to the channel viewed just before the channel currently onscreen Return Lets you program a specific channel to return to while scanning through the channels using the CH and CH buttons T RETURN and hold for three seconds
15. TUP NOW PROGRAMMING lt gt To operate Y g gt lt gt To choose CABLE or AIR 48 AV To move to START Programming will take approximately lt gt To start Auto Tuner Setup 1 to 2 minutes PROGRAMMING OVER e Noise Muting will not work during Auto Tuner Setup Note Some cable systems experience interference from radio frequencies on cable Channel 95 You may delete this channel from your scan by removing the X next to it on the Channel Summary screen shown on the next page Initial Setup Channel Summary Channel Summary allows you to customize the line up of channels received by your TV You can add or delete channels from the line up or prevent any unauthorized viewers from watching any or all 181 channels Ey Press the Menu button AV To CHANNEL SUMMARY CH CH lt gt To operate 01 06 The Channel Summary screen right will now be 02 gt 07 displayed with the channels set to scan marked with an X You can delete channels from the 03 08 scan by removing the X If any channels were 04 09 missed during Auto Tuner Setup and you wish to add them you may by placing an X next to the channel number 05 LO SELECT BY AWM AV To the ADD column OPERATE BY KO EXIT BY EXI lt gt To include or delete from scan Tp Exit when finished You can block access to a channel by activating the Channel Lock AV To CHANNEL SUMMARY lt gt To operate AV To the Lock Column
16. To ON OFF TIMER lt gt To operate begins with ON TIME lt gt To set the hour AM PM you want the TV to turn on y To move to minutes lt gt To set the minutes y To accept ON TIME and move to OFF TIME the time the TV will turn off Set the OFF TIME the same way as ON TIME Vv To accept OFF TIME and move to CHANNEL lt gt To select channel y To move to MODE lt gt Choose ONCE or EVERYDAY v To ON OFF TIMER lt gt Choose YES to accept the timer setting choose NO if you don t wish to accept v To FINISH lt gt To save settings TY Press the Exit button when finished Notes The on off time cannot be set to locked or guarded channels e In order for the on off timer to work the clock must be set e After a power interruption the timer settings must be reset Initial Setup You can choose to view your onscreen menus in three languages English French Francais or Spanish Espa ol Y AV lt gt Y Press the Menu button To LANGUAGE To choose a language ENGLISH gt FRENCH lt gt SPANISH 4 gt Exit when finished Closed Caption Many broadcasts now include an onscreen display of dialog called CLOSED CAPTIONS Some broadcasts may also include displays of additional information in text form Your television can access and display this information using the CLOSED CAPTION feature To activate the closed caption feature follow the steps below AV lt gt Notes
17. To V CHIP lt gt To operate The lock icon a appears TY Press Zero to access V Chip setup options AV To UNRATED UNRATED VIEW BLOCK lt gt To VIEW or BLOCK TY Press Exit when done Initial Setup Set Lock Code Channel guard and V Chip settings are protected by a four digit lock code Your TV comes pre set with a lock code of 0000 You may change the code to any four digit number you wish To change the lock code follow the steps below TY Press the Menu button AV To SET LOCK CODE lt gt To operate lock icon a appears Press Zero to access the lock code LOCK CODE 0000 FINISH The first digit will be highlighted lt gt To select the number AV To move to the next digit Continue to follow these directions for all four numbers AV To FINISH lt gt To save settings and exit your lock code is now set When a viewer attempts to watch a blocked channel this message appears THIS PROGRAM IS LOCKED BY CHANNEL GUARD PLEASE ENTER LOCK CODE BY 10 KEY PAD TO UNLOCK IT NO The channel will remain blocked until the correct lock code is entered see above for information on setting your lock code Notes e After a power interruption you must reset the lock code e Write your lock code number down and keep it hidden from potential viewers e If you forget the lock code a new code may be set using the steps listed above Picture Adjust Picture Settings These settings allow
18. VC Color Monitor Receiver Users Guide For Model TM 2003U Illustration of TM 2003U and RM C205 Important Note In the spaces below enter the model and serial number of your television located at the rear of the television cabinet Staple your sales receipt or invoice to the inside cover of this guide Keep this user s guide in a convenient place for future reference Keep the carton and original packaging for future use Model Number LCT1420 001A A Serial Number 0303 TN II IM Important Safety Precautions CAUTION RISK OF ELECTRICAL SHOCK DO NOT OPEN CAUTION To reduce the risk of electric shock Do not remove WARNING CAUTION cover or back No user serviceable parts inside Refer servicing to qualified service personnel The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance TO PREVENT FIRE OR SHOCK HAZARDS DO NOT EXPOSE THIS TV SET TO RAIN OR MOISTURE TO INSURE PERSONAL SAFETY OBSERVE THE FOLLOWING RULES REGARDING THE USE OF THIS UNIT 1 Operate only from the p
19. a camcorder game console or other equipment to your television by using the front input jacks You can also connect these using the television s rear input jacks using the same instructions Connect a yellow composite cable from the camcorder VIDEO OUT into the VIDEO IN on the front of the TV 2 Connect a white composite cable from the camcorder LEFT AUDIO OUT into the LEFT AUDIO IN on the front of the TV 3 Connect a red composite cable from the camcorder RIGHT AUDIO OUT into the RIGHT AUDIO IN on the front of the TV Note e If your camcorder is a mono sound model it will have only one AUDIO OUT Connect it to the LEFT AUDIO IN ak lt Headphone Connection You can connect a pair of headphones to the television using the headphone jack located on the front of the TV by plugging headphones into the headphone jack on the TV s front panel Quick Setup Auto Tuner Setup Step 3 Auto Tuner Setup JVC s onscreen menu system lets you set your television up to meet your own personal viewing preferences The menu screens and their features are discussed in detail in this book The menu settings are optional you can set as many or as few of them as you wish But to begin watching your television right away you will need to run the Auto Tuner Setup This lets your television learn the channels it is able to receive To run the Auto Tuner Setup follow the steps below TY Press the Menu button on the remote control Pres
20. atellite television system please refer to the satellite TV manual Do you use a Cable TV Box Do you have a VCR Do you have a VCR Diagram 2 Diagram 1 Diagram 3 Diagram 1 Quick Setup Connections A Cable or Antenna Diagram 1 Output p m a ar a a S TV Rear Panel UN Note Cable Box e If you do not have a cable box connect the cable wire directly from the wall outlet into the back of the TV Diagram 2 a ma Before connecting any video devices to the Monitor Receiver A you must connect the BNC Connector Box in order for those rh N voeo devices to work 2 D woo 1 Slide the clips on the back of the BNC connector box into the sa ERE slots to the left of the jackpack on the back of the television 2 Connect the BNC connector box s yellow video cable to the d yellow video input on the TV s rear jack panel Cable or Antenna TV Rear Panel Output BNC Connector Box A TV Rear Panel 7 o ere IN ee o ie E U mono ll Coaxial Cable OUT nib e VCR i OUT OUT i Sy bi OUT N Cable Box Notes e You must connect the video cable from the DVD player to the BNC connector box in order for it to work e If your VCR is a mono sound unit it will have only one audio out jack Connect it to the TV s LEFT AUDIO INPUT e Your VCR must be turned on to view premium cable channels Quick Setup Connections Cable or Antenna
21. cise discretion in permitting viewing by pre teens and early teens Programming may contain mature themes and scenes of intense violence O 18 Adult Material intended for mature audiences only Directions to set Canadian V Chip Ratings Ey Press the Menu button AV To V CHIP lt gt To operate lock icon appears Ey Press Zero to access V Chip setup options AV To SET CANADIAN RATINGS ENG for English lt gt To enter ratings menu For example To block viewing of programming rated 14 and 18 AV To the 18 Column lt gt To turn on the lock 18 14 PG G C8 C AV To the 14 Column TSE IA lt gt To turn on the lock FINISH AV To FINISH lt gt To save settings and exit SELECT BY Mu OPERATE BY BO EXIT BY Xi Initial Setup Unrated Programs Unrated programming refers to any programming which does not contain a rating signal Programming on television stations which do not broadcast rating signals will be placed in the Unrated Programming category Examples of Unrated programs e Emergency Bulletins e Locally Originated Programming e News e Political Programs e Public Service Announcements Religious Programs e Sports Weather Some Commercials Note TV programs or movies that do not have rating signals will be blocked if the unrated category is set to BLOCK Directions to Block Unrated Programs You can block programs that are not rated TY Press the Menu button AV
22. content may also be blocked The content types are VIFV is for VIOLENCE FANTASY VIOLENCE S stands for SEXUAL CONTENT L stands for strong LANGUAGE D stands for suggestive DIALOG Initial Setup Setting US V Chip Ratings TY Press the Menu button V CHIP ON OFF SET US TV RATINGS av To V CHIP l SET MOVIE RATINGS lt gt To operate lock icon a appears SET CANADIAN RATINGS ENG SET CANADIAN RATINGS FRE Press Zero to access the V Chip menu UNRATED VIEW BLOCK lt gt To turn V Chip ON or OFF o SELECT BY mia AV To move to SET US TV RATINGS DENER GF EXIT BY EI lt gt To operate Directions to set US V Chip Ratings Line up the cursor in the column TV PG TV G etc with the content row V FV S etc and press the A or Y to move the cursor to the correct location Press or to turn the locking feature on or off An item is locked if the a icon appears instead of a For example To block viewing of all TV 14 shows move the cursor to the top row of that column and add a lock icon Once you ve put a lock on the top row everything in that column is automatically locked AVY To the TV 14 Column ny lt gt To turn on the lock a AY ToFINISH w lt gt To save settings and exit ik es 7 A TY Press the Exit button when finished L A FINISH SELECT BY MM Note OPERATE BY Ec EXIT BY EXI If you want to change the setup move the cursor to the top column and change the
23. cover the openings with a cloth or other material Never place the TV set near or over a radiator or heat register 9 To avoid personal injury Do not place a TV set on a sloping shelf unless properly secured Use only a cart or stand recommended by the TV set manufacturer Do not try to roll a cart with small casters across thresholds or deep pile carpets Wall or shelf mounting should follow the manufacturer s instructions and should use a mounting kit approved by the manufacturer 10 Caution children about dropping or pushing objects into the TV set through cabinet openings Some internal parts carry hazardous voltages and contact can result in a fire or electrical shock 11 Unplug the TV set from the wall outlet before cleaning Do not use liquid or an aerosol cleaner 12 Never add accessories to a TV set that has not been designed for this purpose Such additions may result in a hazard O PORTABLE CART WARNING Symbol provided by RETAC GS 13 For added protection of the TV set during a lightning storm or when the TV set is to be left unattended for an extended period of time unplug it from the wall outlet and disconnect the antenna This will prevent damage to product due to lightning storms or power line surges 14 ATV set and cart combination should be moved with care Quick stops excessive force and uneven surfaces may cause the TV set and cart combination to overturn Service 15 Unplug this
24. d be suitable for all ages including children ages 2 6 O TV Y7 is for Older Children Most parents would find such programs suitable for children 7 and above These programs may contain some mild fantasy violence or comedic violence which children should be able to discern from reality Programs with the following ratings are designed for the entire audience O TV G stands for General Audience Most parents would find these programs suitable for all age groups They contain little or no violence no strong language and little or no sexual dialog or situations O TV PG Parental Guidance Suggested May contain some but not much strong language limited violence and some suggestive sexual dialog or situations It is recommended that parents watch these programs first or with their children O TV 14 Parents Strongly Cautioned Programs contain some material that may be unsuitable for children under the age of 14 including possible intense violence sexual situations strong coarse language or intensely suggestive dialog Parents are cautioned against unattended viewing by children under 14 O TV MA Mature Audiences Only These programs are specifically for adults and may be unsuitable for anyone under 17 years of age TV MA programs may have extensive V S L or D Viewing Guidelines In addition to the ratings categories explained above information on specific kinds of content are also supplied with the V Chip rating These types of
25. io Output 1W 1W 2x3 1 2 5x9 cm Speakers oval x 2 Antenna Terminal 75 ohms VHF UHF F type connector External Input Video 1 Vp p 75 ohms Jacks Audio 500mVrms 4dBs high impediance 500 mVrms 4 dBs Audio Output Low impedance FIXED 400 Hz when modulated 100 Headphone Jack 3 5 mm x 1 Dimensions Inch 19 7 8 x 17 7 8 x 19 1 2 WxHxD cm 50 3 x 45 2 x 49 3 Weight Ibs kg 43 8 19 9 Remote control unit x 1 AA batteries x 2 BNC Connector Box x 1 Specifications subject to change without notice JVC JVC PROFESSIONAL PRODUCTS COMPANY Division of JVC Americas Corp 1700 Valley Road Wayne New Jersey 07470
26. lt in a picture tube implosion Ask a qualified service technician to dispose of the TV set 20 Note to CATV system installer This reminder is provided to call the CATV system installer s attention to Article 820 40 of the NEC that provides guidelines for proper grounding and in particular specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical Table of Contents Quick Setup Unpacking your TV 7 Diagrams 8 Remote Control 49 Getting Started 10 The Remote Control 10 Connecting Your Devices 11 Auto Tuner Setup 15 Onscreen Menus 16 Using the Guide 16 Initial Setup Auto Tuner Setup 17 Channel Summary 18 V GHIP gt 2 002 000 bk eee na 19 Set Lock Code 26 Picture Adjust Picture Settings 27 Adjust Picture Settings 27 Noise Muting 27 Set Video Status 28 Sound Adjust 29 Sound Settings 29 Adjust Sound Settings 29 MTS Multi channel Sound 29 TV Speaker 30 Clock Timers Set Clock iia sek ee tad ee eo de 31 On Off Timer 32 Language 33 Closed Caption 33 Background 34 Button Functions 35 Men as LE et E ar at o
27. ng TY Press the Exit button when finished MTS Multi Channel Television Sound MTS technology allows several audio signals to be broadcast at once giving you a choice in what you wish to hear with a TV program In addition to mono or stereo sound an MTS broadcast may also include a second audio program SAP TY Press the Menu button AV To MTS lt gt Select the mode The ON AIR arrow tells you if a broadcast is in stereo and or contains an SAP Notes Keep the TV in stereo mode to get the best sound quality The sound will work in stereo mode even if a certain broadcast is in mono sound only Choose the mono setting to reduce excessive noise on a certain channel or broadcast Selecting SAP will allow you to hear an alternative soundtrack if one is available Sound Adjust TV Speaker If your TV is connected to a stereo system you can turn off the TV speakers and listen to the audio through your stereo e AV lt gt Y Press the Menu button To TV SPEAKER TV SPEAKER ON OFF To turn the TV s speakers ON or OFF Exit when finished Before you turn the TV Speaker setting from OFF to ON make sure that the TV volume level is low If the TV volume is set too high the sound level will be extremely loud After a power interruption the TV Speaker settings will return to ON Clock Timers Set Clock Before you use any of your TV s timer functions you must first set the clock You
28. o SET VIDEO STATUS COLOR PICTURE lt gt To operate BRIGHT as aa lt gt To set the TINT levels DETAIL oe AV To move to the next option SAVE AS CHOICE Repeat these steps until all levels are set SELECT BY MU OPERATE BY KO EXIT BY Xi AV To SAVE AS CHOICE lt gt To save settings and exit You must use SAVE AS CHOICE to exit the Set Video Status menu otherwise your preferences will not be saved e You can access your Choice settings at any time by pressing the Vineo Status button on the remote control Note The setting screen will disappear if you do not make any adjustments or move to the next setting in approximately three seconds Any changes you have made to picture settings up to that point will be stored You can exit the Picture Settings menu at any time by pressing the Exit button on the remote control Sound Adjust Sound Settings These settings allow you to change and adjust the sound preferences on your television BASS You can increase or decrease the level of low frequency sound in the TV s audio with the bass adjustment TREBLE Use treble to adjust the level of high frequency sound in your TV s audio BALANCE Adjust the level of sound between the TV s left and right speakers with the balance setting Adjust the Sound Settings TY Press the Menu button AV To BASS TREBLE or BALANCE lt gt To adjust the setting AV To move to the next setti
29. other TV or VCR Move any such appliances further away from the TV There could be interference from a high wattage appliance like a hairdryer or vacuum operating nearby Move the antenna away from the appliance or change to a coaxial cable connection which is less prone to interference A building or passing airplane can reflect the original signal and produce a second slightly delayed one Adjust your antenna position Your antenna may be damaged disconnected or turned Check the antenna connection If the antenna is damaged replace it The Closed Caption Text mode is on Turn it off in the Closed Caption Menu page 33 Make sure the MTS settings are correct See MTS on page 29 The TV Speaker option may be turned off See page 30 It is normal to feel static electricity if you brush or touch the screen is normal for the TV to make crackling sounds when first turned on or off Unless the sound or picture become abnormal this is fine Make sure the BNC connector box is properly connected to the TV The television Video Input Jack RCA is not terminated Specifications MODEL TM 2003U NTSC BTSC System Reception Format Multi Channel Sound VHF 2 to 13 UHF 14 to 69 Sub Mid Mid Super Hyper and Ultra bands 181 channel frequency synthesizer system Power Source AC 120V 60Hz Power r 87W 1 4A Consumption Reception Range 20 inch 51 cm Screen Size measured diagonally full square Aud
30. ower source specified on the unit 2 Avoid damaging the AC plug and power cord 3 Avoid Improper installation and never position the unit where good ventilation is unattainable 4 Do not allow objects or liquid into the cabinet openings 5 In the event of trouble unplug the unit and call a service technician Do not attempt to repair it yourself or remove the rear cover Changes or modifications not approved by JVC could void the warranty When you don t use this TV set for a long period of time be sure to disconnect both the power plug from the AC outlet and antenna for your safety To prevent electric shock do not use this polarized plug with an extension cord receptacle or other outlet unless the blades can be fully inserted to prevent blade exposure IMPORTANT RECYCLING INFORMATION This product utilizes both a Cathode Ray Tube CRT and other components that contain lead Disposal of these materials may be regulated in your community due to environmental considerations For disposal or recycling information please contact your local authorities or the Electronic Industries Alliance http www eiae org Important Safeguards CAUTION Please read and retain for your safety Electrical energy can perform many useful functions This TV set has been engineered and manufactured to assure your personal safety But improper use can result in potential electrical shock or fire hazards In order not to defeat the safeg
31. ror Scan through TV channels when not in a menu screen lt gt Left and right arrows mean press the Votume or Voume buttons to move left or right to Select a highlighted menu item Select an item in a submenu Select numbers in certain menu options Turn the volume up or down when not in a menu screen The press button icon means you should press the button named on your remote Ey control Button names appear in SmaLL CAPITAL LETTERS To bring up the onscreen menu press the Menu button on the remote control The item that appears in yellow is the one currently selected AUTO TUNER SETUP CHANNEL SUMMARY V CHIP SET LOCK CODE SELECT BY DM OPERATE BY BO EXIT BY EXIT Notes e Menus shown in this book are illustrations not exact replications of the television s onscreen displays If you do not press any buttons for a few seconds the onscreen menu will automatically shut off Initial Setup Auto Tuner Setup If you have already run the Auto Tuner as part of the quick setup earlier in this guide please skip ahead to Channel Summary to continue setting up your television In Auto Tuner Setup the TV automatically scans through all available channels memorizing the active ones and skipping over blank ones or channels with weak signals This means when you scan using the CHANNEL buttons you will receive only clear active channels TY Press the Menu button AV To AUTO TUNER SE
32. s the AW buttons to move to AUTO TUNER SETUP Press the lt P buttons to begin AUTO TUNER SETUP TUNER MODE CABLE AIR lt gt To choose CABLE if you are connected to a cable system or AIR if you use an antenna AV To move to START lt gt To start Auto Tuner Setup The Auto Tuner will now memorize all of the clear active channels your television can receive This will take one or two minutes NOW PROGRAMMING gt gt gt Er 48 When the setup is finished PROGRAMMING OVER is displayed Your quick setup is now complete You can now begin watching your television or you can continue on in this guide for more information on programming your remote control or using the JVC onscreen menu system to customize your television viewing experience Cable Box and Satellite Users After your auto tuner setup is complete you may depending on the type of hookup have only 1 channel usually 3 or 4 in the auto tuner memory This is normal The Quick Setup is complete Onscreen Menus Using the Guide Certain symbols are used throughout this guide to help you learn about the features of your new television The ones you will see most frequently are AV Up and Down arrows mean press the CH or Ch buttons Pressing the CH or Ch buttons let you e Move vertically in a main menu screen Move through a submenu screen Move to the next letter number or other choice in a submenu Back up to correct an er
33. station may be having difficulties Check to see if other stations are working Check to see that the batteries are still working and properly installed Make sure the remote has a clear sight path to the TV You may be too far from the TV You must be within 23 feet 7 meters You cannot select a certain channel The power turns off by itself The clock is wrong The On Timer is blinking The color quality is poor There are lines across the picture The picture is spotted There are double pictures ghosts Picture is snowy image noise Screen is 80 black Stereo or bilingual programs can t be heard There is no sound from the TV s speakers Static electricity You hear occasional crackling sounds The picture is excessively bright Make sure the channels have been programmed See Channel Summary page 18 Check to see if the channel is locked See Channel Summary Lock page 18 Make sure the set did not become unplugged Perhaps the On Off Timer is set See page 32 Check to see if the Sleep Timer was set See page 36 e The power was interrupted and the clock was not reset See page 31 There is a problem with the TV Unplug the set and call for service Tint and Color may be improperly adjusted See page 27 The Video Status mode may be turned to the wrong setting See page 28 There could be interference from another electrical appliance such as a computer an
34. the DisPLay button The screen to the right shows the following information The current channel or AV input Channel 05 e The current time 12 20 pm 05 Sleep timer status minutes remaining The NOW 12 20 PM Sleep Timer is off SLEEP TIMER OFF e On off timer status Set to turn on everyday at ON OFF TIMER EVERYDAY 7 00 PM off at 10 00 PM ON TIME 7 00 PM Each Press of the DispLay button changes the OFF TIME 10 00 PM display mode Er Display gt gt Time gt Channel gt Off gt Display Full screen shown above Time Shows the current time only Channel Shows the current channel Off Turns display off Notes e You may also turn off the display at any step by pressing Exit e If the clock sleep timer or on off timer are not set the display screen will show CLOCK NOT SET SLEEP TIMER OFF and ON OFF TIMER OFF respectively Selects the signal input source for the television TV for Antenna or Cable Video 1 or Video 2 for video devices like VCRs DVD players or camcorders Py INPUT gt TV VIDEO 1 VIDEO 2 P Button Functions Video Status The video status button gives you a choice of three TV picture display settings including a display of your own preferences STANDARD Resets the picture display to the factory settings CHOICE Displays the setting levels you specified on the Set Video Status Menu see page 28 GA
35. ting the and markings placing the end in the unit first Snap the cover back into place Key Feature Buttons MUTING The four key feature buttons at the center of the remote can be used for basic operation of the television The top and bottom buttons will scan forward and back through the available channels To move rapidly through the channels using JVC s Hyperscan feature press and hold CH or CH The channels will zip by at a rate of five channels per second The right and left buttons will turn the volume up or down These buttons are also marked with four arrows and are used with JVC s onscreen menu system To use the onscreen menus press the Menu button Quick Setup Connections Basic Operation Turn the television on and off by pressing the Power button at the top right corner E of the remote Step 2 Connecting Your Devices Please follow the flow chart below to determine which connection setup is right for you Then refer to the appropriate diagrams to connect your television to other devices that you may have After you are finished connecting your devices plug the power cord into the nearest power outlet and turn on the TV A VCR is not necessary for operation of the television If you follow these diagrams and the television does not work properly contact your local cable operator To connect a DVD player see Diagram 3 A DVD player is optional If you have a s
36. tions AV To SET MOVIE RATINGS lt gt To enter movies menu For example To block viewing of X and NC 17 rated from shows AV To the X Column lt gt To turn on the lock X 17 R 13 PG AY To the NC 17 Column lt gt To turn on the lock AV To FINISH lt gt To save settings and exit FINISH SELECT BY DM OPERATE BY KO EXIT BY Xi Initial Setup Canadian V Chip Ratings O E Exempt Exempt programming includes news sports documentaries and other information programming talk shows music videos and variety programming O C Programming Intended for Children Violence Guidelines There will be no realistic scenes of violence Depictions of aggressive behavior will be infrequent and limited to portrayals that are clearly imaginary comedic or unrealistic in nature O C8 Programming Intended for Children 8 and Over Violence Guidelines Any realistic depictions of violence will be infrequent discreet of low intensity and will show the consequences of the acts There will be no offensive language nudity or sexual content O G General Audience Programming will contain little violence and will be sensitive to themes which could affect younger children O PG Parental Guidance Programming intended for a general audience but which may not be suitable for younger children Parents may consider some content not appropriate for children aged 8 13 O 14 14 Years and Older Parents are strongly cautioned to exer
37. uards incorporated in this TV set observe the following basic rules for its installation use and servicing Also follow all warnings and instructions marked on your TV set INSTALLATION 1 Your TV set is equipped with a polarized AC line plug one blade of the POLARIZED TYPE plug is wider than the other This safety feature allows the plug to fit into the power outlet only one way Should you be unable to insert the plug fully into the outlet try reversing the plug Should it still fail to fit contact your electrician Operate the TV set only from a power source as indicated on the TV set or refer to the operating instructions for this information If you are not sure of the type of power supply to your home consult your TV set dealer or local power company For battery operation refer to the operating instructions Overloaded AC outlets and extension cords are dangerous and so are frayed power cords and broken plugs They may result in a shock or fire hazard Call your service technician for replacement Do not allow anything to rest on or roll over the power cord and do not place the TV set where power cord is subject to traffic or abuse This may result in a shock or fire hazard Do not use this TV set near water for example near a bathtub washbowl kitchen sink or laundry tub in a wet basement or near swimming pool etc If an outside antenna is connected to the TV set be sure the antenna system is grounded so as to
Download Pdf Manuals
Related Search