JVC VN-V686WPU User's Manual
Contents
1. provided Wind the waterproof tape adhesive of the JVC mark Remove the cap and pull Mount the cap and seal out the cables 6 around the cap and mounting surface with waterproof seal Cable connection cap Waterproof treatment Remove sheet2. Choose the desired frame size JPEG Settings Choose the compression rate from VFS1 VFS7 or select AFS and specify the Jpeg average file size in KByte Approximate file size for each compression rates are as follows Picture Quality VGA File QVGA File Control Method Size Size VFS 80 KB 27 KB Variable File Size 20 60 KB 20 KB 40 KB 13 KB 30 KB 10 KB Selectable Selectable AFS between between ile Si 10KBto100 3KBto Average File Size KB 33 KB MPEG 4 Settings Specify the desired MPEG 4 bitrate Change CBRI VBR FPS Frame Interval and Priority when necessary ED Connect to the Camera x a Searcl SC ki 5 http 192 168 0 2 ES SAE ay ws a Sy Ne et N AGUE I S I AA A VW NETWORKS Niewer ff MPEG4 Viewer Click on Network followed by Basic on the next submenu 4 Change the IP address Click on the menu Network Basic to show setting page N V686 User name Password IP Setting IP Address Subnet Mask 6 Launching Viewer Note for MPEG 4 Viewing Download the ffdshow from the Internet and install before viewing MPEG 4 image with the built in MPEG 4 viewer The ffdshow is a open source CODEC and found at various Internet sites like http www free codecs com FFDShow_download htm as of may 2008 Default Gateway Host Name User name admin Password vn v686 DNS Server by default MAC Address
3. acy Mask and so on situation Remove the terminal cover and connect the fall prevention wire Terminal cover Camera the wire clamp LAN Cable K 5 Power cable DO 2 Connect the LAN Alarm Power cables and tie with re clamp fixing Mount the terminal cover and pull out the cables from side j top Fall Prevention Wire To go under the terminal cover This figure shows pulling the cable from the top a WS the ceiling clamping bracket to the ceiling Front of the C camera w A Pe A tFRONT mark 4 gt y Le Mount the dome cover and remove the protective sheet K J A Dome cover z ae A gt protective Dome Cover sheet Connect the fall prevention wire between units then insert the camera unit into the ceiling clamping bracket Fall prevention wire fixing bracket t mark blue Camera fixing lock knob x2 The Perfect Ex perience J E VN V686WPU Remove the dome cover and take the cushioning and protection material away Cushioning material Heater power switch Fall Prevention Wire Connect LAN Alarm Power cables then push them into Arm Solder welding or crimping Z conversion P connector
4. fk BD cancel Basic Trouble Shooting When some ERROR happens wel If DHCP server exists on the network IP address other than 192 168 0 2 may be assigned to the camera Ask currently assigned IP address for the network administrator or try to connect again in peer to peer environment After selecting DHCP Disable enter the specified value in each fields Press OK and wait for 1 minute while rebooting Change also IP address of the PC to re connect the camera i Encoding settings Click on the menu Image Encoding to show setting page ith no DHCP Server the IP address of the camera should be 192 168 0 2 by default Change also the PC IP address so that the camera and PC are on the logically same subnet Solution 3 Change the IE settings not to use the proxy server for the camera IP address Also set http 192 168 0 2 as an IE trusted site and change the IE setting to allow Active Scripting If you have already setup another camera which was originally the same IP address with the camera this time r z ws PC may still recognize that the corresponding MAC address to According to your system operation policy set the necessary this IP is the previous one Launch the command prompt and settings like type arp a to confirm all IP and corresponding MAC Preset Position address entries To delete all entry type arp d Alarm Note Ping command could be a good solution in any Priv
Download Pdf Manuals
Related Search