JVC VN-T216VPRU User's Manual
Contents
1. DHCP Name IP 2 Notice of Use e This manual is designed for administrators and users of the network camera Please read it carefully before use All requirements should be followed before using this camera e Keep this document for future reference e Please make sure the power source is AC24V PoE Only connect the camera to this power system e The camera must be installed on a solid mounting surface e Keep the camera and other accessories dry e Weare not responsible for any damage caused by inappropriate use e Because the camera controls auto exposure by shutter speed flicker can be shown by fluorescent light To reduce the flicker please select PAL mode if the power is 50Hz or NTSC mode if the power is 60Hz Refer to INSTRUCTIONS 4 Overview of Navigation and Controls Video Type 3 Warnings Installation and maintenance should be performed only by qualified and experienced technicians to conform to all local codes and to maintain your warranty DANGER AC24V models require the use of CSA Certified UL Listed Class 2 power adapters to ensure compliance with electrical safety standards Power over Ethernet PoE should meet the IEEE 802 3af PoE standard CAUTION THIS SYMBOL INDICATES eina THAT DANGEROUS VOLTAGE RE NM CONSTITUTING A RISK OF EPEE REUS ELECTRIC SHOCK IS DO NOT OPEN PRESENT WITHIN THE UNIT CAUTION TO REDUCE THE RISK OF THIS SYMBOL INDICATES ELECTRIC SHOCK DO HOT REMO2. Securit protection Video Access from Full control of all camera settings available to Web Browser administrator Windows XP or Windows 7 as OS Minimum Web Internet Explorer Version 6 0 8 0 Browsing CPU Intel Pentium IV X2 2 4 GHz or equivalent Requirements AMD Memory 1G or above IPv4 HTTP TCP RTSP RTP ICMP UDP IGMP Supported Protocols RTCP FTP DNS DHCP ARP RJ 45 100BASE TX 10BASE T FULL HALF Auto negotiation Surveillance Protocol ONVIF Compatible pass compliance test tool Onboard Storage SDHC suggest class 10 Power Supply PoE IEEE 802 3af Class 0 AC24V Power Consumption PoE 0 15A AC24V 800m A Network interface Power Input removable terminal block Network RJ45 connector Connectors Audio In out removable terminal block Alarm In out removable terminal block Environmental Operating Temperature Operating Humidity 0 to 90 Storage Temperature 20 C to 60 C 10 C to 50 C 2012 JVC KENWOOD Corporation JVC
3. If the message Reply from appears it means the connection is done 4 Start Internet Explorer and enter IP address 192 168 02 A login window will appear Enter the default user name admin and password jvc to log in User Name ED Password __ 5 Images of the camera can be viewed through Internet Explorer Before viewing follow these steps to enable the display a Enable Cookies as shown below In Internet Explorer click Internet Options on the Tools menu On the Privacytab move the settings slider to Low or Accept All Cookies Click OK b When a proxy server is used click Internet Options on the Tools menu of Internet Explorer select Connect tab click LAN button and set proxy server c Change Security in Internet options as shown below e On tool menu click Internet Option e Press the Security tab e f the camera operates inside the Intranet click the Intranet icon If the camera operates on the Internet click the Internet icon e n Windows 7 only Click Tools gt Internet Options 3 Security Enable Protected Mode require restarting Internet Explorer gt Unchecked Internet Options General Security Privacy Content Advanced Select a zone to view or change security settings Local intranet Trustedsites Restricted sites Internet baal This zone is for Internet websites except those listed in trusted and restricted zones Security level for t
4. JVC VN T216VPRU FIXED HD IP DOME CAMERA QUICK GUIDE Contents 1 Ieri me 2 WMD ACK EVER MAG MT EO Qmm 2 FT siio NM T T peat E E dean deena E E 2 Camera WIS FeO coe eset street Sce E E E E 2 Disassembling the Camera sssssssssssssesesennemene enne menn ene inesse reser nens 3 Sese aile I T IQ m Um 3 Adjusting the Camera Position sssssssssssssessesessesenene nemen menm nnne neni nens 5 Mounting th Camera RE Em om mms 6 LOGIC TINS 5 ECC TOTO TETUR 8 Network Configuration Setting Network Camera Environment ccccececeeeececeeeeeeeeseeeeeeaees 8 erige ERU Uu E E 8 Connecting the Camera to a Personal Computer sssssssseene 8 Using IP Finder to Search Camera s IP Address ssssssssessesseene 11 2 vlr HL 12 3 VV IIIS s X S 13 4 DIMENSIONS opre 13 5 lerzreli ezii oip t M I 14 B Contents of this manual e Windows and Internet Explorer are registered trademarks of Microsoft Corporation in the U S e Pentium is a registered trademark of Intel Corporation in the U S e AMD is trademark of Advanced Micro Devices Inc in the U S e Product names of other companies described in this manual are trademarks
5. VE Wi THATIMPORTANT OPERATING THE COVER NO USER SERVICEABLE IN AND MAINTENANCE PARTS INSIDE REFER SERVICING TO INSTRUCTIONS ACCOMPANY QUALIFIED SERVICE PERSONNEL THIS UNIT WEEE Waste Electrical and Electronic Equipment Correct disposal of this product applicable in the European Union and other European countries with separate collection systems This product should be disposed of at the end of its useful life as per applicable local laws regulations and procedures 4 Dimensions 1079 o wa on ue iL M AM I II ir jy wy an e P rij iA p 3 4 NPT 3 4 NPT 13 5 Specifications PAL 1 25 1 10000 sec NTSC 1 30 1 10000 sec Noise Reduction 3 Axis Gimbals Motion detection Lens Type 1 in 1 out Alarm out spec 0 5A AC120V max IP Specifications Video Compression H 264 amp MPEG4 amp MJPEG Real time stream 1 3 type 3 9mm F 1 2 IR cut filter built in l 1080P H 264 or 720P H 264 D1 or D1 D1 Video Streaming Independent controllable frame rate and bandwidth Constant or variable bitrate control NTSC 1080P 1920 x 1080 720P 1280 x 720 D1 720 x 480 4CIF 704 x 480 VGA 640 x 480 CIF 352 x 240 QVGA 320 x 240 Resolution PAL 1080P 1920 x 1080 720P 1280 x 720 D1 720 x 576 4CIF 704 x 576 VGA 640 x 480 CIF 352 x 288 QVGA 320 x 240 PAL Up to 25fps Image Frame Rate NTSC Up to 30fps Multiple user access levels with password
6. g a switch Connectors and field wiring terminals for external Class 2 iu circuits provided with marking indicating minimum Class of ote i wiring to be used Class 2 shall be marked adjacent to the field wiring terminals Washer for Wire Screw for Wire Safety Wire Fall Prevention Wire not Supplied e Connect the wiring then place the camera to a proper position by pushing the button Adjusting the Camera Position The dome camera has three axes for positioning the camera While monitoring the picture on the monitor adjus tthe camera position as follows e Pan Adjustment A For Wall Mount and Tilted Ceilings Rotate the lens base maximum360 until you are satisfied with the field of view e Horizontal Rotation B Rotate 3D assembly in the base Do not turn assembly more than 360 as this assembly may cause the internal cables to twist and disconnect or break e Tilt Adjustment C After loosening the thumbnuts position the camera as desired then finger tighten the thumbnuts to set the position Do not turn the lens more than 360 as this may cause internal cables to disconnect or break Caution Caution Retighten the locking screws to prevent loss of adjustment Mounting the Camera Warning Caution Place the guide pattern sticker supplied on the mounting surface and mark three holes according to the guide pattern sticker Then fasten the sticker to the mounting surface with scre
7. his zone Custom Custom settings To change the settings click Custom level To use the recommended settings click Default level C Enable Protected Mode requires restarting Internet Explorer Custom level Default level Reset all zones to default level e Click Custom Level This will open the Security Settings Internet Zone screen e Scroll down to the ActiveX controls and plug ins radio buttons and set as follows Download signed ActiveX controls gt Prompt recommended Download unsigned ActiveX controls gt Prompt Initialize and script ActiveX not marked as safe for scripting gt Prompt ia Display video and animation on a webpage that does not use Disable Enable rn Download signed ActiveX controls Disable s 7j Enable not secure LI Download unsigned ActiveX controls 3 Disable recommended C3 Enable not secure Ci Initialize and script ActiveX controls not marked as safe for si amp Disable recommended 3 Enable not secure Automatic prompting for ActiveX controls Enable LJ ActiveX controls and plug ins rn Allow previously unused ActiveX controls to run without prom Disable Enable i Allow Scriptlets Disable Enable Prompt LJ Automatic prompting for ActiveX controls Disable Ci Binary and script behaviors 3 Administrator approved E Disable Enable lam O Run ActiveX controls and plug ins gt Enable O Scrip
8. ng on the material of your mounting surface you may require different screws and anchors than those supplied If tilt angle is less than 20 degrees from the horizontal the image can flash by reflection of IR LED light Keeping tilt angle over 20 degrees is recommended when IR LED light is used Locking the Camera e Use soft lint free cloth to wipe the dome cover clean and remove fingerprints e Attach the inner liner and camera housing e Turn the power on after you have installed the camera Network Configuration Setting Network Camera Environment Setting IP This is a network based camera and must be assigned an IP address first The camera s default IP address is 192 168 0 2 and sub mask is 255 255 255 0 To change IP address open Network Settings page described later If your network uses a DHCP server an IP address can be assigned automatically from the DHCP server by enabling DHCP in the Network Settings page described later Connecting the Camera to a Personal Computer 1 Connect the network cable to the camera and then turn on the camera s power 2 Setthe personal computer s IP address The camera s default IP address is 192 168 0 2 and sub mask is 255 255 255 0 3 Checkthat the camera and computer are connected by pinging the IP address you have set To do this start a command prompt Windows from the Start Menu select Program Then select Accessories and choose Command Prompt Type Ping 192 168 0 2
9. or registered trademarks of the respective companies Symbols such as and are omitted in this manual e Design specifications and other contents described in this manual are subject to change for improvements without prior notice 1 Introduction Thank you for purchasing the camera Before installing it read the guide carefully and check the model For more information please refer to the INSTRUCTIONS on CD ROM Unpack Everything e FIXED HD IP DOME CAMERA WARRANTY CARD SAFETY PRECAUTIONS QUICK GUIDE e 2 PIN TERMINAL BLOCK for power input and 8 PIN TERMINAL BLOCK for alarm input output e CD ROM containing INSTRUCTIONS and IP Finder software e TEMPLATE mounting template e WRENCH Hexagon screw driver e 3 SCREW ANCHORs e 3SCREWs e SCREW for WIRE e WASHER for WIRE Preparation The following tools might help you to complete the installation e Drill e Screwdrivers e Wire cutters Camera Installation All the installation and operations here should conform to your local electricity Note safety rules Disassembling the Camera e Gently remove the screw to take off camera housing 4 e Set the camera housing 5 and liner aside Connecting the Wiring Connect the power supply cable to the power connectors Select one of the following options e Inset power cable for AC24V Connect 24 V cables to terminals AC24V e PoE Connect the network cable to the RJ45 terminal usin
10. t ActiveX controls marked safe for scripting gt Enable Li Only allow approved domains to use ActiveX without prompt 3 Disable Enable Ld Run ActiveX controls and plug ins 7j Administrator approved Disable 7j Prompt l Script ActiveX controls marked safe for scripting 3 Disable e Enable j Prompt ml j Press OK to save the settings Close all Internet Explorer windows and start a new window This will allow the new settings to take effect Type your setting IP address into the brows er Then you should be able to see the camera image screen 10 Live View Configuration Full Screen Oneshot Audio In Audio Out Size 1 1 Encoder Mo 1 H 2854 Encoder Mo 2 MJPEG Using IP Finder to Search Camera s IP Address The IP Finder is a tool which helps users to find VN T16 216 series network cameras in the LAN which your computer is connected Please note that IP Finder is only compatible with Windows 7 windows Vista and Windows XP 1 Insert the CD ROMin the CD ROM drive 2 Copy the IP Finder s folder to your computer 3 Double click the IpFinder exe in your computer s IP Finder folder An IP Camera Finder window will pop out The window will display a list of IP cameras which you are using currently 4 Press Search to search cameras amp IP Gamera Finder Wer 3 2 IP Cameras liste Product 1 Camera Name p J eE MAC 0 80 88 41 82 12 IPCAMER 192 168 0 30
11. ws Connect the Safety Wire Fall Prevention Wire not supplied to the camera and the ceiling Secure the camera bottom case 1 to the wall ceiling with tapping screws supplied Adjust the view angle zoom focus and Horizontal Rotation To prevent the camera from falling off ensure that it is connected to a firm place ceiling slab or channel using a Safety Wire Fall Prevention Wire is not supplied Pay also careful attention to the length strength wiring and material insulating properties of the fall prevention wire to be used The length should be as short as possible within the permissible range of the mounting length The wire should be strong enough to withstand the total weight of this product Pay also attention to the finishing at the end of the wire Must be isolated camera and the wall ceiling which are connected by the Safety Wire Fall Prevention Wire v Safety Wire Fall Prevention Wire not supplied any LA p 1 1 HUC Note Note 4S Electrical junction box Optional oOo Rw LV Secure the mounting kit optional to 4S Electrical box using 2 appropriate SCrews Then secure the camera case to mounting kit using 2 appropriate screws Tuck the cables in the 4S Electrical box Adjust the view angle zoom focus and Horizontal Rotation Attach the camera housing Turn the power on after you have installed the camera is optional accessory Dependi
Download Pdf Manuals
Related Search