JVC TK-T8101WPRU User's Manual
Contents
1. 2 Installation 2 1 Mounting the Camera Step 1 Drill mounting holes and insert anchors In desired location use the supplied Guide Pattern to drill three 5mm mounting holes Then insert the supplied anchors into the holes To prevent the camera from falling off ensures it is connected to a firm place ceiling slab or channel using a Safety Wire fall prevention wire is not supplied Safety Wire fall prevention wire is not supplied Please tighten a safety wire on a firm place as photo Step 2 Pass all the signal cables through the hole for the cables Optionally connect a video monitor to the BNC connector if you want to perform focus zoom adjustments during the installation Step 3 For static electricity protection ensure that the rubber pad is placed inside the mounting bracket base Step 4 Modify the position of camera Loosen the two screws left and right first just rotate slightly one circle or the screws will fall down second rotate the Retaining ring then you will be able to hold the camera and adjust its angle Fasten the screws and retaining ring to ensure the desired angle Installation Step 5 Adjustment It can be adjusted once the screw is fully loosened After adjustment be sure to lock it tightly for waterproof Notice Please be careful when adjusting Tele Wide and Near Far so as to avoid damage to the lens Near amp Far Control Tele amp Wide Control OSD joyst2. BRIGHTNESS 024 LOW LUMINANCE MODE AGC BRIGHTNESS x 0 25 RETURN Menu Settings f SHUTTER AGC is set to MANUAL the submenu is shown as below The shutter speed is a variable from 1 50 1 60 sec to 1 10000sec and the AGC is selectable depending on your environment condition MODE SHUT AGC SHUTTER 1 50 AGC 6 0 RETURN Recommended settings according to the application 1 Auto Exposure by Iris Control Application General Purpose Indoor surveillance This is Default settings LENS AUTO SHUTTER AGC AUTO HIGH LUMINANCE MODE AUTO IRIS 2 Auto Exposure by AES first then by IRIS Control Application Outdoor Traffic surveillance LENS AUTO SHUTTER AGC AUTO HIGH LUMINANCE MODE SHUT AUTO IRIS 3 Auto Exposure by Iris Control with fixed Shutter Speed LENS AUTO SHUTTER AGC MANUAL SHUTTER 1 50 1 60 10000 After this the following are set SHUTTER AGC AUTO HIGH LUMINANCE MODE SHUT AUTOIRIS 3 3 WHITE BAL WHITE BALANCE controls color on the screen Options include ATW Auto White Balance PUSH PUSH LOCK USER1 USER2 ANTI CR Anti Color Rolling Suppression and MANUAL The default is ATW e ATW Select ATW when the scene illumination varies between indoor scenes and outdoor scene lighting SPEED 171 DELAY CNT 152 ATW FRAME x 0 50 ENVIRONMENT INDOOR RETURN e MANUAL You can manually adjust the LEVEL from 15 to 69 e USER1 USER2 You can adjust blue setting B GAIN and red
3. 2012 JVC KENWOOD Corporation JVC
4. JVC IR BULLET CAMERA TK T8101WPRU IR BULLET CAMERA TK T8101WPRE INSTRUCTIONS Important Safety Information Before attempting to connect or operate this product please read these instructions carefully and save this manual for future use Important Safety Information Warning and Operating Notes Installation and serving the camera should be performed only by qualified and experienced technicians to conform to all local codes and to maintain your warranty WARNING The use of CSA certified UL Listed Class 2 power adapters are required to ensure compliance Note This product IS intended to be supplied by a Listed Direct Plug In Power Unit marked d output DC 12V 0 58A minimum or AC 24V 60Hz 0 58A minimum for USA WARNING To reduce the risk of fire or electric shock do not expose the product to rain or moisture Connect only one camera to the power line AC24V DC12V Do not share the power line with other eguipment The power cable between power source and the camera must be under 3 m Caution Operating Notes Power Supply This bullet camera can operate on AC 24V or DC 12V Connectors and field wiring terminals for external Class 2 circuits provided with marking indicating minimum Class of wiring to be used Class 2 shall be marked adjacent to the field wiring terminals Note Operating Conditions e Avoid viewing very bright objects example light fixtures for extended periods e Avoid operatin
5. also select where the title appears on the monitor screen 3 12 LANGUAGE OSD supports 8 multiple languages Options include ENGLISH default JAPANESE GERMAN FRENCH RUSSIAN PORTUGUESE SPANISH and SIMPLIFIED CHINESE 3 13 CAMERA RESET To restore factory defaults select CAMERA RESET and then press the joystick control 3 14 SAVE ALL SAVE ALL items allows you to save all settings and exit the OSD menu 4 Specification Signal System NTSC J PAL mager Size Effective pixels HxV 976 H x 494 V 976 H x 582 V F1 4 3 3 12mm Wide 89 8 H 63 6 V ngle of View Tele 23 9 H 17 9 V S N Ratio 50dB typ AGC off Minimum Illumination IR LED 0 Ix Color B amp W switch point 20lx typ Synchronization System Video Output 1Vpp composite output 750 IR Distanc R wavelength 850 Mechanical 0 83mm D x87 W x205 5mm H Weight 680g approx Power Supply I Input Voltage DC 12V amp AC 24V 50Hz 60Hz 10 Power Consumption DC12V 580mA Environmental Operating Temperature 10 50 C Operating Humidity 90 MAX Storage Temperature 20 C 60 C idi 90 MAX FCC Class B Accessories IR BULLET CAMERA X 1 IR BULLET CAMERA X 1 INSTRUCTIONS X 1 INSTRUCTIONS X 1 SAFETY PRECAUTIONS X1 SAFETY PRECAUTIONS X1 WARRANTY CARD X 1 CAUTION CARD X 1 WASHER X3 SCREW X3 SCREW X3 SCREW ANCHOR X3 OSD JOYSTICK SCREW ANCHOR X3 OSD JOYSTICK X 1
6. g or storing the unit in the following locations Extremely humid dusty hot cold environments where the operating temperature is outside the recommended range of 14 F to 122 F 10 C to 50 C Close to sources of powerful radio or TV transmitters Close to fluorescent lamps or objects reflecting light Under unstable light sources may cause flickering CONTENTS 00 00 ee ee 4 CEBI OL m 4 nicer RE 4 1 3 Names of Camera PAR gu 5 1 4 Routine 6 e m 7 2 1 MOUDURA the Camela ie EE EE 7 OSD SE IOS osasta a at d da e EE Ki 10 CMEE UCACTR TK 10 ii i d 10 B SUR FE BAL 11 BAC RO 11 TURE ADIU 12 OR ka ee 12 37 MOTON DEL en a a a a 12 BAR RIV A G i a A 12 a a 13 13 fa CAMERA ID a A 13 OR VAN ICE lCIH 13 3 13 CAMERA RES ad RR i i 13 IPO AVE ACG 13 A SCM OM e T UR l a iene 14 Introductions 1 Instructions The IR Bullet camera is ideal for indoor installation in commercial and residential e
7. ick Step 6 Place the three provided insulation caps onto the three tapping screws Insert the screws to the screw holes on the camera bracket and then tighten the screws to the anchors to attach the camera Menu Settings 3 OSD Settings Use the OSD menu to set up the camera for optimum performance LENS AUTO PRIVACY OFF SHUTTER AGC AUTO DAY NIGHT AUTO WHITE BAL ATW NR BACKLIGHT OFF CAMERA ID OFF PICT ADJUST SYNC INT ATR OFF LANGUAGE ENGLISH MOTION DET OFF CAMERA RESET NEXT BACK EXIT SAVE ALL EXIT SAVE ALL Figure 3 1 Main menu 3 1 Lens The LENS settings allow you to configure Lens and brightness Options are AUTO Auto Iris lens and MANUAL The default setting is AUTO In the AUTO submenu you can set the MODE as OPEN CLOSE or AUTO Then select SPEED to adjust the DC Iris Lens convergence speed TYPE MODE SPEED RETURN 3 2 SHUTTER AGC You can set the SHUTTER AGC as AUTO or MANUAL The default setting is AUTO When LENS is set to AUTO It is recommended to set SHUTTER AGC to AUTO mode In the AUTO submenu adjust HIGH LUMINANCE MODE according to your application AUTO IRIS mode Use this for normal condition application environments The IRIS level will be controlled by camera brightness SHUT AUTO IRIS mode Use this for high light application environments The exposure will be controlled by AES or the DC Iris The iris level will be controlled by camera brightness HIGH LUMINANCE MODE AUTO IRIS
8. nvironment 1 1 Before You Begin Please read this guide carefully before you install the bullet camera Keep this guide for future reference 1 2 Dimensions WW EL 529 N jie 2 Se l i im 0 7 1 M r LE MH An lil co qd MI 111 HL KW AW Ai HAE d SN A J 3 N N N KOM Y 1 3 Names of Camera Parts Figure 2 1 1 Camera main body 5 Mount bracket Connects to the Mount 2 Sun shield Minimize the effects of rain and sunlight on image quality 6 BNC connector Connects to the VIDEO 3 Externally adjustable focal length amp IN connector of the Monitor Video Connector focus 4 OSD menu joystick 7 Power connector Connects to the To use the OSD joystick control external power source Press the OSD joystick control straight DC12V AC24V Please refer to camera label down to enter the Main menu or a selected item Move the OSD joystick control UP DOWN LEFT and RIGHT to navigate through menus and options nd Locations 1 4 Routine Maintenance e Use a soft dry cloth to remove any fingerprints or dust e Clean the camera housing with a soft dry cloth For more stubborn stains use a cloth dampened with a small quantity of neutral detergent then wipe dry Caution Do not use volatile solvents such as alcohol benzene or thinners to avoid damaging the surface finish Installation
9. s to detect moving objectives and adjust the motion detection sensitivity from 0 to 127 3 8 PRIVACY PRIVACY function mask up to 8 privacy areas on the screen from video monitoring The default setting is OFF If selecting ON you will enter the PRIVACY submenu You can configure up to 8 privacy areas and set color and transparency of the privacy zones In addition you can enable MOSAIC function for the privacy zone Note If you enable MOTION DET function then PRIVACY function will support 4 zones only REA SEL TOP BOTTOM LEFT RIGHT COLOR TRANSP MOSAIC RETURN Menu Settings 3 9 DAY NIGHT The camera will automatically switch to B W mode when the illumination is under a certain threshold There is no need to adjust this setting Under B W mode you can set BURST to be ON or OFF 3 10 NR NR allows you to configure the DNR Digital Noise Reduction settings to reduce noise on the screen In the NR submenu you can enable the NR MODE to the Y BRIGHT C COLOR C LEVEL or Y LEVEL mode According to your NR mode you can adjust Y LEVEL or C LEVEL as required NR MODE Y LEVEL C LEVEL RETURN Note When the Y Level is higher the noise in dark areas becomes lessened Also resolution will become lower When it is lower there is more noise in dark areas 3 11 CAMERA ID CAMERA ID displays ON or OFF The default setting is OFF You can set the ON mode to add a camera title up to 26 characters with 2 lines and
10. setting R GAIN value from O to 255 e PUSH When selected in the appropriate position the whole area will perform white balance e PUSH LOCK When selected in the appropriate position WHITE BALANCE will perform once 3 4 BACKLIGHT Set Backlight compensation function It controls the light level to overcome sever backlight conditions Available options include OFF BLC or HLC Highlight Compensation mode The default is OFF Menu Settings If HLC is selected HLC is activated automatically when the camera detects high luminance 3 5 PICTURE ADJUST PICTURE ADJUST allows you to adjust picture settings for optimal image In the PICT ADJUST submenu you can adjust BRIGHTNESS CONTRAST SHARPNESS HUE and GAIN value In addition you can set MIRROR to ON to reflect the image MIRROR BRIGHTNESS CONTRAST SHARPNESS HUE GAIN RETURN 3 6 ATR Set ATR Adaptive Tone curve Reproduction function You can select ON or OFF The default is OFF If selecting ON you will enter the ATR submenu where you can set LUMINACE and CONTRAST to optimize by image LUMINANCE CONTRAST RETURN Also known as Wide Dynamic Range This function expands the video dynamic range of the camera and improves visibility of images even in high contrast environments 3 7 MOTION DET MOTION DET allows to detect moving objects on the screen The default is OFF If selecting ON you will enter the MOTION DET submenu You can set up to 4 motion area
Download Pdf Manuals
Related Search