JVC LVT1047-001A User's Manual
Contents
1. Subwoofer Surround right SP F303F Satellite speaker Type Speaker unit Frequency range Input impedance Power handling capacity Sound pressure level Dimensions Mass 1 way 2 speaker Bass reflex type magnetically shielded type 5 5 cm cone x 2 80 Hz to 20 000 Hz 8 Q 100 W 80 dB W m 250 mm width x 1103 mm height x 250 mm depth 3 77 kg each SP F303C Center speaker Type Speaker unit Frequency range Input impedance Power handling capacity Sound pressure level Dimensions Mass 1 way 2 speaker Bass reflex type magnetically shielded type 5 5 cm cone x 2 80 Hz to 20 000 Hz 8 Q 100 W 81 dB W m 258 mm width x 75 mm height x 81 mm depth 0 95 kg VICTOR COMPANY OF JAPAN LIMITED A EN GE FR NL SP IT SW DA FI PO HU CZ RU CT KO 2003 VICTOR COMPANY OF JAPAN LIMITED 0203NSMIDEHCE2. For satellite speakers for surround _ left right channel e Screws with washer y M4 x 25 mm 16 If any of the items above are missing contact your dealer immediately Speaker and Speaker cords to improve the sound quality When connecting the speaker cords Make sure to match the polarity and otherwise the sound will lose the surround effect After connecting check that the exposed cores are fully inserted into the terminal When using other speaker cords Observe the following e Buy thick speaker cords rather than thin cords and make them as short as possible for connection e Use speaker cords of the same length for both left and right speakers e Do not use long speaker cords otherwise the sound quality may deteriorate Assembly M Assembling the satellite speakers Each speaker except the center speaker has been divided into two parts for shipment Before using this speaker system assemble it first by following the procedure below e Prepare a Phillips screw driver 2 Join the stand to the speaker section Speaker section p J Fix the stand to the speaker section Speaker Stand e Be sure to tighten the screws firmly section Speaker section Stand Before assembling SK Take care not to drop the stand while assembling NS otherwise it may cause damage to the floor or injury Ensure enough space for assembly and installation Place a large thick cloth on
3. speakers M Typical connection method to an amplifier Connect the speakers to a SPEAKER terminal of the amplifier with the speaker cords by referring to the diagram below e Make sure to match the polarity and when connecting the speaker cords e The diagram below is an example of a typical connection method Front right Front left Center speaker Approx 5 m CENTER SURROUND FRONT SPEAKER SPEAKERS SPEAKERS ee gt LEFT Slab HE EBs Speaker terminals on the amplifier Approx 5 m Approx 5 m ji Surround left M Approx 10 m Approx 10 m General Layout of Speakers Place all speakers at the same distance from the listening position if possible e Usually place the center speaker close to the TV Surround left S Front left For a subwoofer to be used with SP F303 it is recommended to use SP DW103 This combination gives you the best possible high quality surround sounds Specifications Listening position 7 them Front right e Do not lean against the speakers as the speakers could fall down or break possibly causing an injury Especially be careful that children do not lean against e When you place the center speaker on a TV make sure the surface is level and stable
4. JVC MM SATELLITE SPEAKER SYSTEM SATELLITEN LAUTSPRECHER SYSTEM SATELLIITTIKAIUTINJARJESTELMA SYSTEME HAUT PARLEURS SATELLITE SYSTEM GLOSNIKOW SATELITARNYCH SATELLIET LUIDSPREKERSYSTEEM KULSO HANGFALRENDSZER SYSTEMA DE ALTAVOZ DE SATELITE SATELITNI REPRODUKTOROVA SOUSTAVA SISTEMA DI ALTOPARLANTI SATELLITI CATEJIJIMTHAA AKYCTUYECKAA CUCTEMA SATELLITHOGTALARSYSTEM a pipes SATELLIT HOJTTALERSYSTEM AMECHOIE AH AXA S P F303 Consists of SP F303F and SP F303C Bestehend aus SP F303F und SP F303C Sisaltaa seuraavat osat SP F303F ja SP F303C Se compose de SP F303F et SP F303C Zestaw przyrzadow SP F303F a SP F303C Bestaat uit SP F303F en SP F303C A k sz l k SP F303F s SP F303C egys gekb l all Consta de SP F303F y SP F303C Sestava komponent SP F303F a SP F303C L impianto formato da SP F303F e SP F303C CocraBneH n3 KOMNOHEHTOB SP F303F u SP F303C Bestar av SP F303F och SP F303C FH SP F303F Az SP F303C Bestar of SP F303F og SP F303C SP F303F 1 SP F303C A INSTRUCTIONS BEDIENUNGSANLEITUNG HASZN LATI UTAS T S MANUEL D INSTRUCTIONS P RU KA OBSLUZE GEBRUIKSAANWIJZING WMHCTPYLIMM NO 3KCTNMNIYATALIMM MANUAL DE INSTRUCCIONES HER ISTRUZIONI ALS HA BRUKSANVISNING VEJLEDNING KAYTTOOHJE INSTRUKCJA OBS UGI LVT1047 001A E Contents Warnings Cautions and Others Assembly Connection General Layout of Speakers Specifications Thank you for purchasing a JVC speaker system Before you begin using these spe
5. akers please read the instructions carefully to be sure you get the best possible performance If you have any questions consult your JVC dealer Warnings Cautions and Others M Precautions for installation e Do not install the speakers on an uneven surface or in a place subject to vibration otherwise they may fall over causing damage or injury Take the occurrence of earthquakes or other physical shocks into consideration when selecting the installation place and secure the speakers thoroughly To prevent deformation or discoloration of the cabinet do not install the speakers where they are exposed to direct sunlight or high humidity and avoid installation near air conditioning outlets Speaker vibrations may cause howling Place the speakers as far away from the player as possible The speakers are magnetically shielded to avoid color distortions on TVs However if not installed properly it may cause color distortions So pay attention to the following when installing the speakers When placing the speakers near a TV set turn off the TV s main power switch or unplug it before installing the speakers Then wait at least 30 minutes before turning on the TV s main power switch again Some TVs may still be affected even though you have followed the above If this happens move the speakers further away from the TV Tuner reception may become noisy or hissing if a speaker is installed near
6. eaker cord into the speaker After connecting check that the exposed cores are fully inserted into the terminal terminal Press and hold Insert the exposed Release your finger the clamp core of the speaker cord fully into the terminal Connection M Connecting the speaker system to the amplifier Before connecting Turn off the power to the amplifier before connecting the speaker system otherwise the speakers may be damaged The impedance of each speaker is 8 Before connecting them to your amplifier check the speaker impedance range of your amplifier If the impedance of this speaker is out of the speaker impedance range indicated on the amplifier you cannot connect this system to the amplifier The maximum power handling capacity of the SP F303 is 100 W Excessive input will result in abnormal noise and possible damage Be sure to turn down the volume level to prevent unwanted noise before performing following operations Turning on or off other components Operating the amplifier Tuning FM stations Fast forwarding a tape Continuously reproducing high frequency oscillation or high pitch electronic sounds When using a microphone do not aim it at the speakers or use it near the speakers otherwise the howling which occurs may damage the speakers Before replacing the cartridge always turn off the power to the turntable otherwise the clicking noise may damage the
7. the floor where you assemble the speaker so you can protect the floor and the speaker itself Use the speaker only after assembly is fully and correctly done Screw 4 4 Supplied M4 x 25 mm x LT X 1 Connect the speaker connecters to the stand connecters It is recommended to place a cushion under the speaker section e You can tighten the screws easily by placing the speaker section horizontally Cushion not supplied Stand Speaker section Rear To be continued on the next page Assembly continued 5 Route the speaker cord as shown below e Be sure to take out the slack so that the speaker cord lies flat 4 Connect the speaker cord to the speaker terminal e Each speaker can be used as front or surround speaker Use the 5 meter speaker cords for front speakers and 10 meter speaker cords for surround speakers Twist and pull the A insulation coat to eo D remove Repeat the procedure from step 1 to assemble the other satellite speakers Press and hold the Insert the exposed Release your finger clamp core of the speaker cord fully into the terminal M Connecting the Center speaker e To connect the center speaker use the same type of speaker cord 5 m tagged with CENTER as used for connecting the front speakers Make sure to match the polarity and otherwise the sound will lose the surround effect Insert the sp
8. the tuner In this case leave more distance between the tuner and the speakers or use an outdoor antenna for better tuner reception without interference from the speakers M Precautions for Daily Use e To maintain the appearance of the speakers Wipe with a dry soft cloth if the cabinet or control panel should become dirty If very dirty apply a small amount of water or neutral detergent to the cloth and wipe clean then wipe with a dry cloth e To improve the sound field If the speakers are facing a solid wall or glass door etc it is recommended to furnish the wall with materials that absorb sounds for example by hanging up thick curtains to prevent reflections and standing waves To use the speakers without any trouble Do not reproduce sounds at so high a volume that they are distorted otherwise the speakers may be damaged by internal heat buildup When moving the speakers do not pull the speaker cords otherwise the speakers may fall over causing damage or injury When holding a satellite speaker do not grasp the speaker upper portion but always grasp the leg lower portion of the satellite speaker m Checking the supplied Accessories Check to be sure you have the following supplied accessories The number in parenthesis indicates the quantity of the piece supplied e Speaker cords Approx 5 m 3 For satellite speakers for front left right channel and center speaker Approx 10 m 2
Download Pdf Manuals
Related Search