JVC KD-S50 User's Manual
Contents
1. AUDIO AMPLIFIER SECTION Maximum Power Output Front 40 watts per channel Hear 40 watts per channel Continuous Power Output RMS Front 16 watts per channel into 4 Q 40 Hz to 20 000 Hz at no more than 0 896 total harmonic distortion Rear 16 watts per channel into 4 Q 40 Hz to 20 000 Hz at no more than 0 8 total harmonic distortion Load Impedance 4 Q 4 Q to 8 Q allowance Tone Control Range Bass 10 dB at 100 Hz Treble 10 dB at 10 kHz Frequency Response 40 Hz to 20 000 Hz Signal to Noise Ratio 70 dB TUNER SECTION Frequency Range FM 87 5 MHz to 107 9 MHz AM 530 kHz to 1 710 kHz FM Tuner Usable Sensitivity 11 3 dBf 1 0 pV 75 Q 50 dB Quieting Sensitivity 16 3 dBf 1 8 uV 75 Q Alternate Channel Selectivity 400 kHz 65 dB Frequency Response 40 Hz to 15 000 Hz Stereo Separation 35 dB Capture Ratio 1 5 dB AM Tuner Sensitivity 20 uV Selectivity 35 dB CD PLAYER SECTION Type Compact disc player Signal Detection System Non contact optical pickup semiconductor laser Number of channels 2 channels stereo Frequency Response 5 Hz to 20 000 Hz Dynamic Range 96 dB Signal to Noise Ratio 98 dB Wow and Flutter Less than measurable limit GENERAL Power Requirement Operating Voltage DC 14 4 volts 11 volts to 16 volts allowance Allowable Working Temperature 0 C to 40 C 32 F to 104 F Grounding System Negative ground Dimensions W x H x D Installation Size 182 mm x2. Each time you press the button the adjustable items change as follows Equalization pattern changes as you adjust the bass or treble Indication To do Range BAS Adjust the bass 06 min Note Bass Normally the and buttons works as the volume 06 max control So you do not have to select VOL to adjust TRE Adjust the treble 06 min the volume level Treble 06 max a Turning on off the loudness FAD Adjust the front RO6 Rear only Fader and rear speaker fu nction balance FO6 Front only BAL Adjust the left LO6 Left only The human ear is less sensitive to low and high Balance and right speaker frequencies at low volumes balance RO6 Right only The loudness function can boost these frequencies level to produce well balanced sound at low volume level VOL Adjust the volume 00 min Each time you press LOUD the loudness function Volume turns on and off alternatively 50 max If you are using a two speaker system set the fader E li FIT FIN itm a level to OO ws L LILI 4 Ley CX WE 12 Using the Sound Control Memory SCM You can select and store a preset sound adjustment suitable to each playback source Advanced SCM Selecting and storing the sound modes Once you select a sound mode it is stored in memory lt will be recalled every time you select the same source and will be shown on the display A
3. Thank you for purchasing a JVC product Please read all instructions carefully before operation to ensure your complete understanding and to obtain the best possible performance from the unit CONTENTS How to reset your unit ssssssss 2 LOCATION OF THE BUTTONS 4 AAA e mudins pibe Re RETKEM dun D 4 BASIC OPERATIONS 9 Turning on the power eesessss 5 RADIO BASIC OPERATIONS 6 Listening to the radio 6 Storing station in memory 7 Tuning into a preset station 8 Other convenient tuner functions 8 CD OPERATIONS e 9 Paymo PEI a RN 9 Locating a track or a particular portion Ma D E aa 10 Selecting CD playback modes 10 Prohibiting CD ejection 11 BEFORE USE For safety Do not raise the volume level too much as this will block outside sounds making driving dangerous e Stop the car before performing any complicated operations SOUND ADJUSTMENTS 12 Adjusting the sound 12 Turning on off the loudness function 12 Using the Sound Control Memory SCM 13 Storing your own sound adjustments 14 OTHER MAIN FUNCTIONS 15 Setting the clock nriman aan 15 To c
4. Note When you stand the unit be careful not to damage the fuse on the rear Insert the 2 handles between the unit and the sleeve as illustrated to disengage the sleeve locks 3 Remove the sleeve Note Be sure to keep the handles for future use after installing the unit 4 Install the sleeve into the dashboard After the sleeve is correctly installed in the dashboard bend the appropriate tabs to hold the sleeve firmly in place as illustrated 5 Fixthe mounting bolt to the rear of the unit s body and place the rubber cushion over the end of the bolt 6 Dothe required electrical connections explained on the back of this instructions Slide the unit into the sleeve until it is locked 8 Attach the trim plate so that the projection on the trim plate is fixed to the left side of the unit 9 Attach the control panel Handle Manija Poign e Cubierta Manchon Fusible Fusible Lock Plate Plaque de Slot Ranura Fente TROUBLESHOOTING The fuse blows Are the red and black leads connected correctly Power cannot be turned on Is the yellow lead connected e No sound from the speakers Is the speaker output lead short circuited e Sound is distorted Is the speaker output lead grounded Are the terminals of L and R speakers grounded in common Unit becomes hot s the speaker output lead grounded Are the terminals of Land R
5. correctly e BEFORE connecting the speaker leads of the power cord to the speakers check the speaker wiring in your car If the speaker wiring in your car is as illustrated in Fig 1 and Fig 2 below DO NOT connect the unit using that original speaker wiring If you do the unit will be seriously damaged Redo the speaker wiring so that you can connect the unit to the speakers as illustrated in Fig 3 If the speaker wiring in your car is as illustrated in Fig 3 you can connect the unit using the original speaker wiring in your car f you are not sure of the speaker wiring of your car consult your car dealer PRECAUCIONES sobre las conexiones de la fuente de alimentaci n y de los altavoces e NO conecte los conductores de altavoz del cable de alimentaci n a la bater a de autom vil pues podr an producirse graves da os en la unidad e Conecte correctamente el conductor negro a tierra el conductor amarillo a la bater a del autom vil 12V constantes y el conductor rojo a un terminal de accesorio e ANTES de conectar a los altavoces los conductores de altavoz del cable de alimentaci n verifique el conexionado de altavoz de su autom vil Si el conexionado de altavoz de su autom vil es como se indica en las Figs 1 y 2 de abajo NO conecte la unidad utilizando ese conexionado de altavoz original Si lo hace se producir n da os graves en la unidad Vuelva a efectuar el conexionado de altavoz d
6. n de la unidad sin utilizar la cubierta l appareil sans utiliser de manchon In a Toyota for example first remove the car radio and install the unit in its place En un Toyota por ejemplo primero extraiga la radio del autom vil y luego instale la unidad en su lugar Fire wall Tabique a prueba de incendios Cloison Flat type screws M5 x 6 mm Tornillos tipo plano M5 x 6 mm Vis a t te plate M5 x 6 mm Stay option Soporte opci n Hauban en option Washer Arandela Dashboard Tablero de instrumentos Lock nut Tableau de bord Tuerca de seguridad Ecrou d arr t Bracket M nsula B Support Screw option Tornillo opci n Mounting bolt Vis en option Perno de montaje Boulon de montage Pocket Compartimiento Poche Cubierta Manchon Par exemple dans une Toyota retirer d abord l autoradio et installer l appareil a la place Not included with this unit No suministrado con esta unidad Non fourni avec cet appareil Bracket Flat type screws M5 x 6 mm M nsula Tornillos tipo plano M5 x 6 mm Support Vis t te plate M5 x 6 mm Note When installing the unit on the mounting bracket make sure to use the 6 mm long screws If longer screws are used they could damage the unit Nota Cuando instala la unidad en la m nsula de montaje aseg rese de utilizar los tornillos de 6 mm de longitud Si se utilizan tornillos m s largos stos pueden da ar la unidad Remarque Lo
7. stereo RND random indicator HPT repeat indicator SOM indicator LOUD indicator Sound mode indicators BEAT SOFT POP CD indicator Band indicators FM1 FM2 FM3 AM Main display CD IN indicator BASIC OPERATIONS 4 Turning on the power Turn on the power O 1 ATT Note on One Touch Operation When you select a source in step 2 below the power automatically comes on You do not have to press this button to turn on the power 2 Select the source To operate the tuner FM or AM see pages 6 8 To operate the CD see pages 9 11 3 Adjust the volume To increase the volume To decrease the volume Volume level appears Volume level indicator see page 16 4 Adjust the sound as you want see page 12 14 To drop the volume in a moment Press O 1 ATT briefly while listening to any source ATT starts flashing on the display and the volume level will drop in a moment To resume the previous volume level press the button briefly again To turn off the power Press and hold I ATT until SEE YOU appears on the display Note When you use this unit for the first time set the built in clock correctly see page 15 CAUTION on volume setting CDs produce very little noise compared with other sources If the volume level is adjusted for the tuner for example the speakers may be damaged by the sudden increase in the output level Therefore lower t
8. 52 mm x 150 mm 7 3 16 x 2 1 16 x 5 15 16 Panel Size 188 mm x 58 mm x 14 mm 7 7 16 x 2 5 16 x 5 8 Mass 1 3 kg 2 9 lbs excluding accessories Design and specifications subject to change without notice If a kit is necessary for your car consult your telephone directory for the nearest car audio speciality shop MER VE VAST WI http TG tee mobile com Visit us on line for Technical Support amp Customer Satisfaction Survey US RESIDENTS ONLY Having TROUBLE with operation Please reset your unit Refer to page of How to Reset Still having trouble USA ONLY Call 1 800 252 5722 http www jvcservice com We can help you GA EN SP FR 0801kKSFLEJES KD S50 Installation Connection Manual Manual de instalaci n conexi n Manuel d installation raccordement GET0077 002A J ENGLISH e This unit is designed to operate on 12 V DC NEGATIVE ground electrical systems INSTALLATION IN DASH MOUNTING e The following illustration shows a typical installation However you should make adjustments corresponding to your specific car If you have any questions or require information regarding installation kits consult your JVC car audio dealer or a company supplying kits 1 Before mounting Press LA Control Panel Release to detach the control panel if already attached 2 Remove the trim plate 3 Remove the sleeve after disengaging the sleeve locks D Stand the unit
9. Retrait de l appareil e Avant de retirer l appareil lib rer la section arri re 1 Retirer le panneau de commande 2 Retirer la plaque d assemblage Introduire les deux poign es dans les fentes comme montr Puis tout en tirant doucement les poign es cart es faire glisser l appareil pour le sortir S assurer de conserver les poign es apres l installation de l appareil Manija Poign e Liste des pi ces pour l installation et raccordement Les pi ces suivantes sont fournies avec cet appareil Apres v rification veuillez les placer correctement Power cord Cord n de alimentaci n Cordon d alimentation Lock nut M5 Tuerca de seguridad M5 Ecrou d arr t M5 Y SK SIN SY Rubber cushion Coj n de goma Amortisseur en caoutchouc O ELECTRICAL CONNECTIONS To prevent short circuits we recommend that you disconnect the battery s negative terminal and make all electrical connections before installing the unit If you are not sure how to install this unit correctly have it installed by a qualified technician Note This unit is designed to operate only on 12 V DC NEGATIVE ground electrical systems If your vehicle does not have this system a voltage inverter is required which can be purchased at JVC car audio dealers Replace the fuse with one of the specified rating If the fuse blows frequently consult your JVC car audio dealer If noise is a problem This unit incorporate
10. ajustage de facon que la projection de la plaque soit fix e sur le cote gauche de l appareil 9 Remonter le panneau de commande Dashboard Tablero de instrumentos Tableau de bord Rubber cushion Coj n de goma 197 Amortisseur en caoutchouc mm Mounting bolt Perno de montaje x Boulon de montage See the back page for electrical connections Con respecto a las conexiones el ctricas consulte la p gina de atr s Voir le dos de cette page pour les connexions lectriques EN CAS DE DIFFICULTES Le fusible saute Les fils rouge et noir sont ils racord s correctement e L appareil ne peut pas tre mise sous tension Le fil jaune est elle raccord e e Pas de son des haut parleurs Le fil de sortie de haut parleur est il court circuit Le son est d form Le fil de sortie de haut parleur est il la masse Les bornes des haut parleurs gauche et droit sont elles mises ensemble la masse L appareil devient chaud Le fil de sortie de haut parleur est il la masse Les bornes des haut parleurs gauche et droit sont elles mises ensemble la masse e When using the optional stay e Cuando emplea un soporte opcional e Lors de l utilisation du hauban en option Lors de l installation de e When installing the unit without using the sleeve e Instalaci
11. connectors with a cotton swab or cloth moistened with alcohol being careful not to damage the connectors Connectors I o sal O Z T 18 o MAINTENANCE Handling CDs This unit has been designed only to reproduce the CDs bearing the OS mark DIGITAL AUDIO Other discs cannot be played back Center holder How to handle CDs When removing a CD from its A case press down the center 2 holder of the case and lift the CD out holding it by the edges Always hold the CD by the edges Do not touch its recording surface When storing a CD into its case gently insert the CD around the center holder with the printed surface facing up Make sure to store CDs into the cases after use To keep CDs clean A dirty CD may not play correctly If a CD does becomes dirty wipe it with a soft cloth in a straight line from center to edge To play new CDs New CDs may have some rough spots around the inner and outer edges If such a CD is used this unit may reject the CD To remove these rough spots rub the edges with a pencil or ball point pen etc About mistracking Mistracking may result from driving on extremely rough roads This does not damage the unit and the CD but will be annoying We recommend that you stop CD play while driving on such rough roads Moisture condensation Moisture may condense on the lens inside the CD player in the following cases
12. connexion v rifiez attentivement le c blage du v hicule pour ne pas connecter incorrectement cet appareil Une connexion incorrecte peut endommager s rieusement l appareil 1 Connectez les fils de couleur du cordon d alimentation la batterie de la voiture aux enceintes et l antenne automatique s il y en a une dans l ordre suivant D Noir a la masse Jaune a la batterie de la voiture 12V constant Rouge la prise accessoire 4 Bleu bandes blanches l antenne automatique 200mA max 5 Autres aux enceintes 2 Connectez le cordon d antenne 3 Finalement connectez le faisceau de fils l appareil Ignition switch Interruptor de encendido Interrupteur d allumage fy 1 Before checking the operation of this unit prior to installation this lead must be connected otherwise power cannot be turned on 1 Antes de comprobar el funcionamiento de esta unidad previa a de la instalaci n es necesario conectar este cable de lo contrario no se podr conectar la alimentaci n 1 Pour v rifier le fonctionnement de cet appareil avant installation ce fil doit tre raccord sinon l appareil ne peut pas tre mis sous tension Left speaker front Altavoz izquierdo frontal Haut parleur gauche avant Jaune Red Rojo Blue with white stripe A A un terminal activo del bloque de fusibles conectado a la bater a del autom vil desviando el int
13. el perno de montaje ou la parte trasera del cuerpo de la unidad y coloque el coj n de goma sobre el extremo del perno 6 Realice las conexiones el ctricas requeridas en base a las explicaciones que figuran en la parte de atr s de estas instrucciones Deslice la unidad dentro de la cubierta hasta que quede trabada 8 Coloque la placa de guarnici n de manera que el saliente de la misma quede colocado en el lateral izquierdo de la unidad Y Coloque el panel de control Sleeve Cubierta Manchon Trim plate Placa de guarnici n Plaque d assemblage Placa de bloqueo verrouillage LOCALIZACION DE AVERIAS e El fusible se quema Est n los conductores rojo y negro correctamente conectados e No es posible conectar la alimentaci n Est el cable amarillo conectado No sale sonido de los altavoces mE Est el cable de salida del altavoz cortocircuitado El sonido presenta distorsi n Est el cable de salida del altavoz conectado a masa Est n los terminales una masa com n La unidad se calienta Est el cable de salida del altavoz conectado a masa Est n los terminales una masa com n x e e 0 A de los altavoces L y R conectados a de los altavoces L y R conectados a FRANCAIS e Cet appareil est concu pour fonctionner sur des sources de courant continu de 12 V a masse NEGATIVE INSTALLATION MONTAGE DANS LE TABLEAU DE BORD e Lillustr
14. manual mode will automatically turn off after 5 seconds f you hold down the button the frequency keeps changing until you release the button When an FM stereo broadcast is hard to receive Press MO RND monaural random while listening to an FM stereo broadcast e Each time you press the button the MO indicator lights up and goes off alternately Lights up when receiving an FM broadcast in stereo Hs pi A gi HHA HHR 5 y LA 0 EHE i 5B um L OA i HHA h MT F Ei Nap H E When the MO indicator is lit on the display the sound you hear becomes monaural but the reception will be improved the ST indicator goes off ff M ZI Storing stations in memory You can use one of the following two methods to store broadcasting stations in memory Automatic preset of FM stations SSM Strong station Sequential Memory Manual preset of both FM and AM stations FM station automatic preset SSM You can preset 6 local FM stations in each FM band FM1 FM2 and FM3 Select the band FM1 3 you want to store FM stations into e Each time you press the button the FM band changes as follows FM1 FM2 FM3 2 Press and hold both buttons for more than 2 seconds 4 SSM ty peni ma TTM B Ij v SSM appears then disappears when automatic preset is over Local FM stations with the strongest signals are searched and sto
15. sound mode can be stored for each of the following sources FM1 FM2 FM3 AM CD If you do not want to store the sound mode separately for each playback source but want to use the same sound mode for all the sources see To cancel Advanced SCM on page 15 Select the sound mode you want Each time you press the button the sound mode changes as follows When SCM LINK is set to LINK ON the selected sound mode can be stored in memory for the current source and the effect applies only to the current source Each time you change the playback source the SCM indicator flashes on the display e When SCM LINK is set to LINK OFF the selected sound mode effect applies to any source Indication For Preset values Bass Treble Loudness BEAT Rock or disco 02 00 On music SOFT Quiet 01 03 Off background music POP Light music 04 01 Off SCM OFF Flat sound 00 00 On so Recalling the sound modes When SCM LINK is set to LINK ON select the source Sound mode indicator Each time you change the playback source the SCM indicator flashes on the display Notes You can adjust each sound mode to your preference and store it in memory If you want to adjust and store your original sound mode see Storing your own sound adjustment on page l4 To adjust the bass and treble reinforcement levels or to turn onloff the loudness function temporarily
16. 10A fuse Fusible de 10A Fusible 10A Antenna terminal Terminal de la antena Borne de l antenne 2 To antenna A la antena A l antenne Antes de la conexi n Verifique atentamente el conexionado del veh culo para no cometer errores al conectar esta unidad Una conexi n incorrecta podr a producir dafios graves en la unidad 1 Conecte los conductores de color del cable de alimentaci n a la bater a del autom vil altavoces y antena autom tica si la hubiere en la secuencia siguiente D Negro a tierra 2 Amarillo a la bater a del autom vil 12V constantes 3 Rojo a un terminal de accesorio 4 Azul con rayas blancas a la antena autom tica 200mA m x 5 Otros a los altavoces 2 Conecte el cable de antena 3 Por ltimo conecte a la unidad el cableado preformado Rear ground terminal Terminal de tierra posterior i Borne arri re de masse To metallic body or chassis of the car A un cuerpo met lico o chasis del autom vil Vers corps m tallique ou ch ssis du v hicule Yellow Amarillo bypassing the ignition swich Not supplied with this unit No suministrado con esta unidad Non fourni avec cet appareil 2 D yaa To a live terminal in the fuse block connecting to the car battery RACCORDEMENTS ELECTRIQUES Pour viter tout court circuit nous vous recommandons de d brancher la borne n gative de la batterie et d effectuer tous les raccordements lectriqu
17. After starting the heater in the car If it becomes very humid inside the car Should this occur the CD player may malfunction In this case eject the CD and leave the unit turned on for a few hours until the moisture evaporates When playing a CD R Recordable You can playback your original CD Rs on this receiver Before playing back CD Rs read their instructions or cautions carefully e Some CD Rs recorded on CD recorders may not be played back on this receiver because of their disc characteristics and of the following reasons Discs are dirty or scratched Moisture condensation occurs on the lens inside the unit The pickup lens inside the CD player is dirty Use only finalized CD Rs CD RWs Rewritable cannot be played back on this recevier Do not use CD Rs with stickers or sticking labels on the surface They may cause malfunctions CAUTIONS Do not insert 8cm 3 3 16 CDs single CDs into the loading slot Such CDs cannot be ejected Do not insert any CD of unusual shape like a heart or flower otherwise it will cause a malfunction Do not expose CDs to direct sunlight or any heat source or place them in a place subject to high temperature and humidity Do not leave them in a car Do not use any solvent for example conventional record cleaner spray thinner benzine etc to clean CDs TROUBLESHOOTING 9 What appears to be trouble is not always serious Check t
18. H CLOCK M SCM LINK or Playback sources ud When shipped from the factory a different sound mode can be stored in memory for each source so that you can change the sound modes simply by changing the sources LINK ON Advanced SCM different SCM for LEVEL appears on the display 2 different sources Set the hour l l T Select CEOCK Una onthe LINK OFF Conventional SCM one SCM for all l sources display 5 Adi 2 Adjust the hour Press and hold SEL for more than 2 seconds CLOCK H CLOCK M SCM LINK or LEVEL appears on the display ay OOF Q Ces Ve Vs N S 3 Set the minute 1 Select CLOCK M 2 Adjust the minute 2 2 Select SCM LINK if not shown on the display 4 Press SEL select to finish the setting To check the current clock time changing 3 Select the desire mode LINK ON the display mode or LINK OFF Press DISP repeatedly Each time you press the button the display mode changes as follows During tuner operation Frequency Clock 4 Press SEL select to finish the setting During CD operation Elapsed _ Clock playing time e If the unit is not in use when you press DISP the power turns on the clock time is shown for 5 seconds then the power turns off 15 dE Selecting the level display 3 Select the desired mode VOL 15 VOL 2 or OFF Yo
19. JVC MM CD RECEIVER KD S50 I o O Z ui RECEPTOR CON CD KD S50 FRANCAIS ESPANOL RECEPTEUR CD KD S50 COMPACT For installation and connections refer to the separate manual DIGITAL AUDIO Para la instalaci n y las conexiones refi rase al manual separado Pour l installation et les raccordements se r f rer au manuel s par For Customer Use Enter below the Model No and Serial No which are located on the top or bottom of the cabinet INS TRUCTIONS Retain this information for future reference MANUAL DE INSTRUCCIONES MANUEL D INSTRUCTIONS Model No GET0077 001A J I o O Z Lu INFORMATION For USA This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the
20. ancel advanced SCM 15 Selecting the level display 16 Detaching the control panel 17 MAINTENANCE 18 Handing GDS rai 18 TROUBLESHOOTING 19 SPECIFICATIONS 20 Temperature inside the car If you have parked the car for a long time in hot or cold weather wait until the temperature in the car becomes normal before operating the unit I o sal O Z ui iN LOCATION OF THE BUTTONS Control panel Ls eo o 7 E al o e A e e fe S s a Display window FA 7 71 T Th 114 nm m i m T AN uE HHH Y fio d O I ATT standby on attenuator button button LOUD button MO monaural button RND random button Display window A eject button CD button FM button AM button SEL select button Ha Y A p buttons e Also functions as SSM buttons when pressed together Number buttons DISP display button RPT repeat button SCAN button SCM sound control memory button y control panel release button DOS 21 22 23 6 7 8 9 TE I m i Tit 49 M 15 16 Display window fe El ES 53 83 ss ex E Volume or audio level indicator Equalization Pattern indicator Tuner reception indicators MO monaural ST
21. ation suivante est un exemple d installation typique Cependant vous devez faire les ajustements correspondant votre voiture particuli re Si vous avez des questions ou avez besoin d information sur des kits d installation consulter votre revendeur d autoradios JVC ou une compagnie d approvisionnement 1 Avant le montage Appuyez sur lA d blocage du panneau de commande pour ventuellement d tacher le panneau de commande 2 Retirer la plaque d assemblage 3 Lib rer les verrous du manchon et retirer le manchon Poser l appareil la verticale Remarque Lorsque vous mettez l appareil la verticale faire attention de ne pas endommager le fusible situ sur le fond 2 Ins rer les 2 poign es entre l appareil et le manchon comme indiqu pour d sengag les verrous de manchon Retirer le manchon Remarque S assurer de garder les poign es pour une utilisation ult rieur apres l installation de l appareil 4 Installer le manchon dans le tableau de bord Apres installation correcte du manchon dans le tableau de bord plier les bonnes pattes pour maintenir fermement le manchon en place comme montr 5 Monter le boulon de montage sur l arri re du corps de l appareil puis passer l amortisseur en caoutchouc sur l extr mit du boulon D R alisez les connexions lectriques expliqu es au dos de cette page Faire glisser l appareil dans le manchon jusqu ce qu il soit verrouill 8 Attachez la plaque d
22. ay You can play back all tracks on the CD at random Each time you press MO RND Mono Random while playing a CD CD random play mode turns on and off alternatively The RND indicator SS TVE d Ung FINAS d xs When the random mode is turned on the RND indicator lights up on the display and a track randomly selected starts playing To play back tracks repeatedly Repeat Play You can play back the current track repeatedly Each time you press RPT SCAN Repeat Scan while playing a CD CD repeat play mode turns on and off alternatively Track number The RPT of the currently indicator playing track When the repeat mode is turned on the RPT indicator lights up on the display Prohibiting CD ejection You can prohibit the CD ejection and can lock a CD in the loading slot Press and hold CD and 4 for more than 2 seconds EJECT flashes on the display for about 5 seconds and the CD is locked and cannot be ejected To cancel the prohibition and unlock the CD press and hold CD and 4 again for more than 2 seconds when pressing CD EJECT appears on the display and the CD ejects from the loading slot 11 I o s O Z TT 9 SOUND ADJUSTMENTS Adjusting the sound 2 Adjust the level You can adjust the sound characteristics to your To increase the level preference I o sal O Z T To decrease the level Select the item you want to adjust
23. e manera que pueda conectar la unidad a los altavoces de la manera indicada en la Fig 3 Si el conexionado de altavoz de su autom vil es como se indica en la Fig 3 podr conectar la unidad utilizando el conexionado de altavoz original de su autom vil Si tiene dudas sobre el conexionado de altavoz de su autom vil consulte con su concesionario Solder the core wires to connect them securely ouelde los alambres de alma para conectarlos con firmeza Souder les mes desfils pour les raccorder entre eux de facon s re Twist the core wires when connecting Hetuerza los alambres de alma para conectarlos Torsader les mes des fils en les raccordant tape PRECAUTIONS sur l alimentation et la connexion des enceintes e NE CONNECTEZ PAS les fils d enceintes du cordon d alimentation la batterie sinon l appareil serait s rieusement endommag e Connectez correctement le fil noir a la masse le fil jaune a la batterie de la voiture 12V constant et le fil rouge la prise accessoire e AVANT de connecter les fils d enceintes du cordon d alimentation aux enceintes v rifiez le c blage des enceintes de votre voiture Si le c blage des enceintes de votre voiture est r alis comme montr sur la Fig 1 ou Fig 2 ci dessous NE CONNECTEZ PAS l appareil en utilisant ce c blage original d enceintes Si vous le faites l appareil sera s rieusement endommag Recommencez le c blage des encein
24. ember that you must store stations first If you have not stored them yet see Storing stations in memory on page 7 and 8 Select the band FM1 3 AM FM3 2 Select the number 1 6 for the preset station you want 7 8 9 10 11 12 Other convenient tuner functions RPT SCAN Scanning broadcast station When you press RPT SCAN while listening to the radio station scanning starts Each time a broadcast is tuned in scanning stops for about 5 seconds tuned frequency number flashes on the display and you can check what program is now being broadcasted If you want to listen to that program press the same button again to stop scanning CD OPERATIONS 6 gt DIRECT TRACK ACCESS I o O Z TT Playing a CD To stop play and eject the CD Press 4 inserta disc into the loading slot CD play stops and the CD automatically ejects The unit turns on from the loading slot The source changes to the gt draws a CD and starts tuner you will hear the last received station CSS playback automatically If you change the source to AM FM the CD play n also stops without ejecting the CD this time E Notes When a CD is inserted upside down the CD automatically ejects Ifthe ejected disc is not removed for about 15 seconds the disc is automatically inserted again into the loading slot to protect it from dust CD play will not start this time You can eject the CD even when the unit is
25. erruptor de encendido A une borne sous tension du porte fusible connect e la batterie de la voiture en d rivant l interrupteur d allumage To an accessory terminal in the fuse block A un terminal accesorio del bloque de fusibles Vers borne accessoire du porte fusible Azul con rayas blancas Bleu avec bande blanche a gt i Right speaker front Altavoz derecho frontal Haut parleur droit avant Left speaker rear Altavoz izquierdo trasero Haut parleur gauche arri re Fuse block bloque de fusibles porte fusible White with black stripe White Gray with black stripe Gray Green with black stripe Green Purple with black stripe Blanco con rayas negras Blanco Gris con rayas negras Gris Verde con rayas negras Verde P rpura con rayas negras Blanc avec bande noire Blanc Gris avec bande noire Gris Vert avec bande noire Vert Violet avec bande noire To automatic antenna if any A la antena autom tica si la hubiere Vers borne d antenne automatique s il y en a une Purple P rpura Violet Right speaker rear Altavoz derecho trasero Haut parleur droit arri re PRECAUTIONS on power supply and speaker connections e DO NOT connect the speaker leads of the power cord to the car battery otherwise the unit will be seriously damaged e Connect the black lead ground yellow lead to car battery constant 12V and red lead to an accessory terminal
26. es avant d installer l appareil Si l on n est pas s r de pouvoir installer correctement cet appareil le faire installer par un technicien qualifi Remarque Cet appareil est concu pour fonctionner sur des sources de courant continu de 12V masse NEGATIVE seulement Si votre v hicule n offre pas ce type d alimentation il vous faut un convertisseur de tension que vous pouvez acheter chez un revendeur d autoradios JVC Hemplacer le fusible par un de la valeur pr cis e Si le fusible saute souvent consulter votre revendeur d autoradios JVC e Si le bruit est un probl me Cet appareil incorpore un filtre de bruit dans le circuit d alimentation Cependant avec certains v hicules quelques claquements ou autres bruits non d sir s risquent de se produire Si cela arrive raccorder la borne de masse arriere de l appareil au ch ssis de la voiture voir le sch ma de raccordement ci dessous en utilisant des cordons les plus gros et les plus courts possibles telle qu une barre de cuivre ou une tresse Si le bruit persiste consulter votre revendeur d autoradios JVC e La puissance admissible des haut parleurs doit tre sup rieure 40 W l arri re et 40 W l avant avec une impedance de 4 Q a8 Q0 e S assurer de raccorder la mise la masse de cet appareil au ch ssis de la voiture e Le radiateur devient tr s chaud apr s usage Faire attention de ne pas le toucher en retirant cet appareil Avant de commencer la
27. following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help IMPORTANT FOR LASER PRODUCTS Precautions 1 2 3 CLASS 1 LASER PRODUCT DANGER Invisible laser radiation when open and interlock failed or defeated Avoid direct exposure to beam CAUTION Do not open the top cover There are no user serviceable parts inside Leave all servicing to qualified service personnel CAUTION This CD player uses invisible laser radiation however is equipped with safety switches to prevent radiation emission when unloading CDs It is dangerous to defeat the safety switches CAUTION Use of controls adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure How to reset your unit O ATT Press and hold both the SEL Select and 0 I ATT l Standby On ATT Standby On ATT buttons at the same time for several seconds This will reset the built in microcomputer NOTES Your preset adjustments such as preset channels or sound adjustments will also be erased Ifa CD is in the unit it will eject when you reset the unit Pay attention not to drop the CD SEL Select
28. he following points before calling a service center CD cannot be played back CD is inserted upside down Insert the CD correctly CD sound is sometimes You are driving on rough roads Stop CD play while driving interrupted rough roads CD is scratched Change the CD Connections are incorrect Check the cords and connections NO DISC appears on the No CD is in the loading slot Insert a CD into the loading slot display CD is inserted incorrectly Insert it correctly Sound cannot be heard from The volume control is turned to Adjust it to the optimum level the speakers the minimum level Connections are incorrect Check the cords and connections SSM Strong station Signals are too weak Store stations manually Sequential Memory automatic preset does not work Static noise while listening to The antenna is not connected Connect the antenna firmly the radio firmly CD can be neither played back The CD player may function Press QO I ATT and 4 at the nor ejected incorrectly same time for more than 2 seconds Be careful not to drop CD wheniit is ejected I o O Z TT The unit does not work at all The built in microcomputer may Press I ATT and SEL at the function incorrectly due to noise same time for more than 2 etc seconds to reset the unit The clock setting and preset stations stored in memory are erased See page 2 19 I o sal O Z T SPECIFICATIONS
29. he volume before playing a disc and adjust it as required during playback ENGLISH RADIO BASIC OPERATIONS DIRECT TRACK ACCESS I o sal O Z ui Listening to the radio To stop searching before a station is received press the same button you have pressed for searching You can use either automatic searching or manual searching to tune into a particular station Searchina a station manuallv Searching a station automatically Manual search Auto search Select the band FM 1 3 AM Select the band FM 1 3 AM SE FM1 F A a 09 Note This receiver has three FM bands FMI FM2 FM3 You can use any one of them to listen to an FM broadcast selected band appears 2 Press and hold A or lt lt v until Volume level indicator see page 16 M manual starts flashing on the display Note This receiver has three FM bands FM1 FM2 FM3 You can use any one of them to listen to an FM broadcast 2 Start searching a station 277 GL x Press MA bP to search ELA JA AL x stations of higher frequencies selected band appears Press lt lt Y to search stations of lower frequencies When a station Is received searching stops 3 Tune into a station you want while M is flashing Press Ito search stations of higher frequencies Press a lt YW to search stations of lower frequencies f you release your finger from the button the
30. l ruido fuese un problema Esta unidad tiene un filtro de ruido en el circuito de alimentaci n Sin embargo en algunos veh culos pueden producirse chasquidos u otros ruidos indeseados En tal caso conecte el terminal de tierra posterior Ver diagrama de conexi n abajo del receptor al chasis del autom vil utilizando cordones m s gruesos y cortos tales como alambre de cobre trenzado o de grueso calibre Si el ruido persiste consulte a su concesionario de JVC de equipos de audio para autom vil e La entrada m xima de los altavoces traseros debe ser mayor de 40 W y la de los delanteros de 40 W con una impedancia de 40a80 e Aseg rese de conectar esta unidad a tierra en el chasis del autom vil e El sumidero t rmico estar muy caliente despu s del uso Aseg rese de no tocarlo al desmontar esta unidad EX Typical Connections Conexiones t picas Raccordements typiques Before connecting Check the wiring in the vehicle carefully not to fail in connecting this unit Incorrect connection may cause a serious damage to this unit 7 Connect the colored leads of the power cord to the car battery speakers and automatic antenna if any in the following sequence CD Black ground 2 Yellow to car battery constant 12V 3 Red to an accessory terminal 4 Blue with white stripe to automatic antenna 200mA max 5 Others to speakers 2 Connect the antenna cord 3 Finally connect the wiring harness to the unit
31. red automatically in the band number you have selected FM1 FM2 or FM3 These stations are preset in the number buttons No 1 lowest frequency to No 6 highest frequency When automatic preset is over the station stored in number button 1 will be automatically tuned in I o O Z IT I o sal O Z T ZZ A FIM SAW Manual preset You can preset up to 6 stations in each band FM1 FM2 FM3 and AM manually Ex Storing an FM station of 88 3 MHz into the preset number 1 of the FM1 band Select the band FM1 3 you want to store FM stations into in this example FM1 e Each time you press the button the FM band changes as follows NN FM3 2 Tune into a station of 88 3 MHz Press AA bP to tune stations of higher frequencies Press lt lt N to tune stations of lower frequencies 3 Press and hold the number button in this example 1 for more than 2 seconds ST gt ED 0023 01d FU gas rog xu P1 flashes for a few seconds 4 Repeat the above procedure to store other stations into other preset numbers Notes e A previously preset station is erased when a new station is stored in the same preset number Preset stations are erased whent the power supply to the memory circuit is interrupted for example during battery replacement If this occurs preset the stations again Tuning into a preset station You can easily tune into a preset station Hem
32. rs de l installation de l appareil sur le support de montage s assurer d utiliser des vis d une longueur de 6 mm Si des vis plus longues sont utilis es elles peuvent endommager l appareil Extracci n de la unidad e Antes de extraer la unidad libere la secci n trasera Removing the unit Before removing the unit release the rear section 1 Remove the control panel 1 Extraiga el panel de control 2 Remove the trim plate 2 Retire la placa de guarnici n 3 Inserte las 2 manijas entre las ranuras como se muestra Luego separe gentilmente las manijas y extraiga la unidad Aseg rese de conservar las manijas despu s de instalarlo 3 Insert the 2 handles into the slots as shown Then while gently pulling the handles away from each other slide out the unit Be sure to keep the handles after installing it 2 Parts list for installation and connection The following parts are provided with this unit After checking them please set them correctly Lista de piezas para instalacion y conexion Con esta unidad se suministran las siguientes piezas Despu s de inspeccionarlas coloquelas correctamente Sleeve Cubierta Manchon Control Panel Panel de control Panneau de command Trim plate Placa de guarnicion Plaque d assemblage Washer 5 Arandela 5 Rondelle 95 S Handles Manijas Poign es y cp Mounting bolt M5 x 20 mm Perno de montaje M5 x 20 mm Boulon de montage M5 x 20 mm
33. s a noise filter in the power circuit However with some vehicles clicking or other unwanted noise may occur If this happens connect the unit s rear ground terminal See connection diagram below to the car s chassis using shorter and thicker cords such as copper braiding or gauge wire If noise still persists consult your JVC car audio dealer Maximum input of the speakers should be more than 40 W at the rear and 40 W at the front with an impedance of 4 Q to 8 Q Be sure to ground this unit to the car s chassis The heat sink becomes very hot after use Be careful not to touch it when removing this unit Heat sink Sumidero t rmico Dissipateur de chaleur CONEXIONES ELECTRICAS Para evitar cortocircuitos recomendamos que desconecte el terminal negativo de la bater a y que efect e todas las conexiones el ctricas antes de instalar la unidad Si usted no est seguro de c mo instalar correctamente la unidad h gala instalar por un t cnico cualificado Nota Esta unidad est dise ada para funcionar con 12 V de CC con sistemas el ctricos de masa NEGATIVA solamente Si su veh culo no posee este sistema ser necesario un inversor de tensi n que puede ser adquirido en los concesionarios de JVC de equipos de audio para autom viles e Reemplace el fusible por uno con la corriente especificada Si el fusible se quemase frecuentemente consulte con su concesionario de JVC de equipos de audio para autom viles e Si e
34. see page 12 Your adjustments will be cancelled if another source is selected 13 I o S O Z TT I o sal O Z T 14 O Storing your own sound adjustment You can adjust the sound modes BEAT SOFT POP see page 13 to your preference and store your own adjustments in memory There is a time limit in doing the following procedure If the setting is cancelled before you finish start from step 1 again can up the sound mode you want to adjust See page 13 for details Eo 2 Select BAS bass or TRE treble To turn ON OFF the loudness function See page 12 for details Each time you press LOUD the loudness function turns on and off alternatively gt go to step 5 ES 3 Adjust the bass or treble level See page 12 for details 4 Repeat steps 2 and 3 to adjust the other items 5 Press and hold SCM until the sound mode you have selected in step 1 flashes on the display Your adjustment made for the selected sound mode is stored in memory Eo 6 Repeat the same procedure to store other sound modes To reset to the factory settings Repeat the same procedure and reassign the preset values listed in the table on page 13 OTHER MAIN FUNCTIONS am Setting the clock To Cancel Advanced SCM i Press and hold SEL Select for more You can cancel the Advanced SCM Sound Control D than 2 seconds Memory and unlink the sound modes and the MES CLOCK
35. speakers grounded in common ES ESPANOL Vo 0801 KKSFLEJES EN SP FR e Esta unidad est dise ada para funcionar con 12 V de CC con sistemas el ctricos de masa NEGATIVA INSTALACION MONTAJE EN EL TABLERO DE INSTRUMENTOS e La siguiente ilustraci n muestra una instalaci n t pica Sin embargo usted deber efectuar los ajustes correspondientes a su autom vil Si tiene alguna pregunta o necesita informaci n acerca de las herramientas para instalaci n consulte con su concesionario de JVC de equipos de audio para autom viles o a una compa a que suministra tales herramientas Antes de instalar Pulse La soltar panel de control para separar el panel de control si ya est unido 2 Retire la placa de guarnici n 3 Retire la cubierta despu s de desenganchar los retenes de la cubierta D Ponga la unidad vertical Nota Al poner la unidad vertical tenga cuidado de no da ar el fusible provisto en la parte posterior 2 Inserte las dos asas entre la unidad y la cubierta tal como en la ilustraci n y desenganche los retenes de la cubierta 3 Retire la cubierta Nota Despu s de instalar la unidad aseg rese de guardar las asas para uso futuro 4 Instale la cubierta en el tablero de instrumentos Despu s de que la cubierta est correctamente instalada en el tablero de instrumentos doble las leng etas correspondientes para sostener la cubierta firmemente en su lugar tal como se muestra 5 Fixe
36. tes de facon que vous puissiez connecter l appareil aux enceintes comme montr sur la Fig 3 Si le c blage des enceintes de votre voiture est comme montr sur la Fig 3 vous pouvez connecter l appareil en utilisant ce c blage original d enceintes pour votre voiture Si vous n tes pas s rs du c blage d enceintes de votre voiture consulter le concessionnaire de votre voiture CAUTION PRECAUCION PRECAUTION To prevent short circuit cover the terminals of the UNUSED leads with insulating Para evitar cortocircuitos cubra los cables NO UTILIZADOS con cinta aislante Pour viter les court circuits couvrir les bornes des fils qui ne sont PAS utilis s avec de la bande isolante
37. turned off uy Ly T WE LIII ll Total playing time of Total track number of the inserted disc the inserted disc Elapsed playing time Current track Note on One Touch Operation When a CD is already in the loading slot pressing CD turns on the unit and starts playback automatically I o O Z T Locating a track or a particular portion on a CD To fast forward or reverse the track Press and hold A bP while playing a CD to fast CEN dear forward the track NA S TONS Press and hold qi y while playing a CD to reverse the track To go to the next tracks or the previous tracks Press A M briefly while TEN m playing a CD to go ahead CER a to the beginning of the next NET track Each time you press the button consecutively the beginning of the next tracks is located and played back Press lt lt V briefly while playing a CD to go back to the beginning of the current track Each time you press the button consecutively the beginning of the previous tracks is located and played back To go to a particular track directly 10 7 8 9 11 12 Press the number button corresponding to the track number to start its playback To select a track number from 1 6 Press 1 7 6 12 briefly To select a track number from 7 12 Press and hold 1 7 6 12 for more than 1 second Selecting CD playback modes To play back tracks at random Random Pl
38. u can select the level display according to your preference When shipped from the factory VOL 2 is selected VOL 1 Shows the volume level indicator and the equalization pattern indicator VOL 2 Alternates VOL 1 setting and illumination display OFF Erase the volume level indicator and the equalization pattern indicator 4 Press SEL select to finish the setting I o sal O Z T Press and hold SEL for more than 2 seconds CLOCK H CLOCK M SCM LINK or LEVEL appears on the display 2 Select LEVEL if not shown on the display CLOCK H CLOCK M SCM LINK or LEVEL appears on the display 16 ary Detaching the control panel How to attach the control panel o You can detach the control panel when leaving the car insert the left side of the control panel gt When detaching or attaching the control panel be into the groove on the panel holder Lu careful not to damage the connectors on the back of the control panel and on the panel holder How to detach the control panel Before detaching the control panel be sure to turn off the power Unlock the control panel 2 Press the right side of the control panel to fix it to the panel holder 2 Lift and pull the control panel out of the unit Note on cleaning the connectors If you frequently detach the control panel the connectors will deteriorate To minimize this possibility periodically wipe the
Download Pdf Manuals
Related Search