JVC HR-S1902U User's Manual
Contents
1. RF cable supplied S video cable not supplied RF Connection 1 Disconnect the TV antenna from the TV 2 Connect the TV antenna cable to the ANT IN terminal on the rear of the VCR 3 Connect the supplied RF cable between the TV OUT terminal on the rear of the VCR and the TV s antenna input terminal AV Connection improves picture quality during tape playback If your TV is equipped with audio video input connectors 1 Connect the antenna VCR and TV as shown in the illustration 2 Connect an audio video cable between the AUDIO VIDEO OUT connectors on the rear of the VCR and the audio video input connectors on the TV S video Connection allows you to make the most of the S VHS picture performance If your TV is equipped with a S video input connector 1 Perform RF Connection previously described 2 Connect a S video cable between the S VIDEO OUT connector on the rear of the VCR and the S video input connector on the TV 3 Connect an audio cable between the AUDIO OUT connectors on the rear of the VCR and the audio input connectors on the TV e Even if you are using audio video cables to connect your VCR to your TV you must also connect it using the RF cable This will ensure that you can record one show while watching another El Perform Plug amp Play setup Plug the AC power cord into an AC outlet Do not turn on the VCR The clock and tuner channe2. ON OFF When this function is set to ON you can record on VHS cassettes with S VHS picture quality Tapes recorded using this function can be played back on most of S VHS VCRs or VHS VCRs equipped with the SQPB S VHS QUASI PLAYBACK function When this function is set to ON the S VHS indicator lights up on the display panel NOTES Before recording set AUTO PICTURE to ON gt See below You cannot activate the S VHS ET function while recording timer recording or Instant Timer Recording C pg 9 or the AUTO PICTURE function t See below is in progress The S VHS ET function does not work with S VHS cassettes To keep the highest quality recording and playback pictures over a long period of time S VHS recording on S VHS cassettes is recommended Use of high grade tapes is recommended for S VHS ET recordings On some tapes picture quality will not improve even if the S VHS ET function is used Check the recording quality before you start important recordings AUTO PICTURE ON OFF When this function is set to ON this VCR checks the condition of the tape in use during playback and compensates to provide the highest possible pictures E PICTURE CONTROL AUTO NORM EDIT SOFT SHARP This function helps you to adjust the playback picture quality according to your preference AUTO NORM Normally select this Picture quality is adjusted automatically When
3. 100 times Repeat Play During playback press and hold PLAY B gt for more than 5 seconds The play indicator E gt on the display panel starts blinking slowly To stop playback press STOP IM on the Remote or STOP EJECT W on the VCR Locating beginning of recordings Index Search When recording on this VCR index codes are placed on the tape at the beginning of each recording E While the tape is not running press kK or gt on the Remote to start search BA To access a recording of 2 to 9 index codes away press lt lt 4 or P repeatedly until the correct number is displayed on the screen only if SUPERIMPOSE is set to ON gt pg 12 Playback begins automatically when the desired recording is located Beginning of the Current Beginning of the current program position on 2nd next program recorded the tape recorded Previous Next program program 2nd next recorded recorded 2 1 lt 1 2 lt 3 lt _ _ id P _ Locating beginning of timer recordings Instant Review After ensuring that the VCR is turned off and that the timer mode is disengaged press REVIEW The VCR turns on and rewinds to the index code indicating the beginning of the last timer recorded program then begins playback automatically e You can access a program of 2 to 9 index codes away from the current position on the tape If for example you have 5 programs recorded and you want
4. PAER You can select channel in the stop mode recording pause mode or during rewind fast forward 4 0 If you connect the TV and the VCR only using the RF connection press TV VCR on the Remote so that the VCR mode indicator lights on the display panel to view the program to be recorded Set tape speed Press SP EP The selected tape speed will appear on the TV screen NOTE You can select tape speed in the stop mode or during recording pause mode El Start recording On the VCR press REC Or on the Remote while holding REC press PLAY P NOTE If AUTO PICTURE is set to ON F pg 11 default setting the VCR takes about 7 seconds to assess the quality of the tape in use then recording begins with the picture level optimized During recording Pause recording Press PAUSE Hl Press PLAY B gt to resume recording You can select channel in the recording pause mode Stop recording Press STOP MM on the Remote NOTE If the tape reaches its end during recording the recording stops and and on the display panel blink Press STOP EJECT amp on the VCR to eject the cassette or press REW lt 4 lt 4 on the Remote to rewind the tape OR Press STOP EJECT Mi 4 on the VCR Recording Features Turn on the VCR and TV and select the VCR channel or AV mode Specifying recording length Instant Timer Recording ITR During recording
5. occurs CONTINUED ON NEXT PAGE Tuner Setting Turn on the VCR and TV and select the VCR channel or AV mode Setting channels automatically Auto Channel Set Perform Auto Channel Set only if channels have not been set correctly by the Plug amp Play setting El Access Main Menu screen then Tuner MAIN MENU Set screen FUNCTION SET Press MENU on the Remote Press AV to INIIALSET move the highlight bar arrow to TUNER SET then press OK or D PRESS ay THEW 0K PRESS TOE FA Perform Auto Channel Set Press AV to move the highlight bar arrow to AUTO CHANNEL SET then press OK or gt The VCR selects the correct band TV or CATV automatically during Auto Channel Set When Auto Channel Set is complete SCAN COMPLETED appears on screen If the scan was unsuccessful SCAN COMPLETED NO SIGNAL appears on screen Check the connections and start again Press MENU to return to normal screen TUNER SET BAND CATV AUTO CHANNEL SET MANUAL CHANNEL SET SELECT WITH a7 AND OK PRESS MENU TO END AUTO CHANNEL SET SCANNING PRESS MENU TO END Setting channels manually Manval Channel Set You can add the channels you want or delete the channels you do not want manually El Access Main Menu screen then Tuner Set screen Press MENU on the Remote Press AV to move the highlight bar arrow to TUNER SET then press OK or D gt MAIN MENU F
6. opposite direction button repeatedly During still picture press and hold to start forward or lt lt to start reverse slow motion playback When you release the button still picture resumes During still picture holding PAUSE ll for more than 2 seconds also starts forward slow motion playback If you press PAUSE Hl again still picture resumes NOTE During slow motion some noise may appear on the TV screen Press CHA Y on the Remote to eliminate the noise CONTINUED ON NEXT PAGE Forward Reverse Reverse Reverse Reverse Slow Normal Forward search play slow motion play search 3 steps motion 1 step 4 steps 1 step When the tape is not running Rewind fast forward Press REW lt lt or FF BP Eject the cassette Press STOP EJECT W amp You can also eject the cassette when the VCR is turned off Turn off the VCR Press POWER 0 1 Playback Features Turn on the VCR and TV and select the VCR channel or AV mode Adjusting tracking condition Tracking Adjustment Automatic tracking adjustment Whenever you insert a tape and start playback automatic tracking starts working and continuously analyzes the signal to enable optimum picture quality during playback Manual tracking adjustment If automatic tracking cannot eliminate noises well during playback follow the procedures below On the Remote El Press SP EP during playback to activ
7. press REC on the VCR repeatedly until the recording length you want appears on the display panel The record indicator O on the display panel starts blinking Each time you press the button recording length increases in 30 minute intervals up to 6 hours The VCR shuts off after recording is finished e To cancel an ITR press STOP MM on the Remote or STOP EJECT W 4 on the VCR Watching one program while recording another During recording If you connect the TV and the VCR only using the RF connection CF pg 5 to view pictures from the VCR press TV VCR on the Remote so that VCR mode indicator goes off from the display panel The TV broadcast being recorded disappears If you are using the AV connection or S video connection pg 5 to view pictures from the VCR change the TV s input mode from AV to TV Then select the channel you want to watch on theTV Second Audio Recording This VCR s built in MTS decoder enables reception of Multichannel TV Sound broadcast To record a SAP program received set 2ND AUDIO RECORD to ON F pg 12 S VHS Super VHS S VHS ET or VHS Recording Mode This VCR can record in S VHS Super VHS S VHS ET or VHS To record in S VHS Set S VHS MODE to ON F pg 12 Then insert a cassette marked S VHS The S VHS indicator lights up on the display panel The S VHS recording mode is selected e To record in S VHS ET on a VHS ca
8. 6 and Auto Channel Set F pg 7 or Manual Channel Set F pg 7 Set VCR channel The VCR channel is the channel on which you can watch the picture from the VCR on the TV when only using the RF connection With no tape in the VCR press POWER to turn off the VCR then press STOP EJECT H on the VCR for more than 5 seconds CH3 appears on the display panel Press CHA V on the Remote to select CH3 CH4 or CH OFF then press OK The VCR channel is preset to CH3 Set to CH4 if CH3 is used for broadcasting in your area EJ Final preparation for use Turn on the VCR and the TV and select the VCR channel 3 or 4 or AV mode on the TV You can now perform basic playback or basic recording If you connect the TV and the VCR only using the RF connection press TV VCR on the Remote so that the VCR mode indicator lights on the display panel Initial Settings Language Setting The default setting is ENGLISH Turn on the VCR and TV and select the VCR channel or AV mode El Access Main Menu screen then Initial MAIN MENU FUNCTION SET Set screen FUNCTION Press MENU on the Remote Press AV to move the highlight bar arrow to INITIAL SET then press OK or gt PRESS a v THEN OK PRESS MENU TO END PA Select language INITIAL SET This VCR offers you the language choice to ciock ser view menus and some messages in English Spa
9. TO THE REFURBISHED PRODUCT WARRANTY INFORMATION PACKAGED WITH EACH REFURBISHED PRODUCT For customer use Enter below the Model No and Serial No which is located either on the rear bottom or side of the cabinet Retain this information for future reference Model No Serial No Purchase date Name of dealer 16
10. VCR Do not apply too much pressure when inserting The VCR turns on and the counter on the on screen display is reset automatically If the cassette s record safety tab has been removed playback begins automatically FA Start playback Press PLAY B gt The S VHS indicator lights up when you play back a tape recorded in S VHS mode or in S VHS ET mode F pg 9 During playback Stop playback Press STOP W on the Remote OR Press STOP EJECT H amp on the VCR Pause playback and view still picture Press PAUSE Hl Press PLAY B gt to resume normal playback NOTE During still picture vertical vibration may appear on the TV screen Press CHA V on the Remote to get a clearer picture Pause and Frame by Frame playback Press PAUSE Ill to pause then press lt 4 or gt l or PAUSE II repeatedly Press PLAY B gt to resume normal playback Picture Search Press REW lt lt or FF BB Press REW lt 4 lt or FF BP again to perform high speed search Each time you press REW lt lt or FF gt the search speed changes between low speed and high speed Press PLAY B gt to resume normal playback Variable Speed Picture Search including slow motion Press kad or BPI repeatedly Press PLAY B gt to resume normal playback Each time you press kad or gt l the playback speed changes To decrease the speed during picture search press the
11. back to the beginning E Complete Semiauto Clock Set Press MENU to return to normal screen Turn off the VCR Aut will appear on the display panel while the clock is being set The current clock time will appear automatically when the clock setting is complete Selections of host channel and D S T mode will be reset to AUTO after a power failure occurs Setting dock manually Manual Clock Set First follow steps Hl to A in Preparations above then go to the following steps El Set time date and year CLOCK SET Press AV until the desired time appears JUME rrm DATE YEAR then press OK or Set the date and year auro CLOCK ON in the same way hee aug AM Holding AV changes the time in 30 TIME ZONE AUTO minute intervals or changes the date in 15 day intervals FA Select D S T mode CLOCK SET Press OK or gt to move the highlight bar to TME ay Se D S T then press AV to select the AUTO CLOCK OFF desired setting DST ONG ON Adjustment will be made by the RSS Ewi THEN T built in clock itself PRESS MENU TO END OFF Select when Daylight Saving Time does not apply to you Start clock Press MENU and normal screen appears PRESS a v THEN OK PRESS MENU TO END To make corrections any time during the process Press OK or gt repeatedly until the item you want to change blinks then press AV Manual setting of the clock will be lost after a power failure
12. capacity Quartz 1 year programable timer 8 programs Memory backup for timer is not supported ACCESSORIES Provided accessories Infrared remote control unit Lithium battery CR2032 RF cable F type Specifications shown are for SP mode unless specified otherwise E amp O E Design and specifications subject to change without notice A FOR SERVICING Only in U S A HOW TO LOCATE YOUR JVC SERVICE CENTER TOLL FREE 1 800 537 5722 http www jvc com Dear Customer In order to receive the most satisfaction from your purchase please read the instruction booklet before operating the unit In the event that repair is necessary or for the address nearest your location within the Continental United States please call 1 800 537 5722 for your nearest authorized servicer or visit our website at www JVC com Remember to retain your Bill of Sale for Warranty Service JVC JVC SERVICE amp ENGINEERING COMPANY OF AMERICA DIVISION OF JVC AMERICAS CORP Sophisticated electronic products may require occasional service Just as quality is a keyword in the engineering and production of the wide array of JVC products service is the key to maintaining the high level performance for which JVC is world famous The JVC service and engineering organization stands behind our products NATIONAL HEADQUARTERS JVC SERVICE amp ENGINEERING COMPANY OF AMERICA DIVISION OF JVC AMERICAS CORP 10 New Maple Avenue Pine Br
13. external input on the recording VCR On this VCR when using this VCR as the recording VCR Select F 1 when connecting the other VCR to the audio video input connectors on the front panel Press AUX or CHA V on the Remote Or on the VCR press PAUSE CH and then FF CH or REW CH See step H in Basic Recording F pg 9 EJ Select video input connector on recording VCR When using this VCR as the recording VCR select the appropriate mode F pg 12 When using S VIDEO input connector on the front panel set FRONT AUX INPUT to S VIDEO When using VIDEO input connector on the front panel set FRONT AUX INPUT to VIDEO H Select edit mode Set the edit mode to ON for the VCRs if such a mode is equipped On this VCR set PICTURE CONTROL to EDIT pg 11 EJ Start playback Press PLAY B gt on the playback VCR Start recording Press REC on the recording VCR Various connection for editing tapes The following three methods can be used for editing tapes VHS to S VHS editing VIDEO VIDEO connection Although the picture quality is inherently limited by the original VHS quality the edited tape has better picture quality than those made by VHS to VHS editing S VHS to VHS editing VIDEO VIDEO connection Since the original source is recorded in S VHS mode the edited tape has better picture quality than those made by VHS to VHS editing S VHS to S VH
14. grounding electrode 2 Lightning For added protection for this product during a lightning storm or when it is left unattended and unused for long periods of time unplug it from the wall outlet and disconnect the antenna or cable system This will prevent damage to the product due to lightning and power line surges 3 Power Lines An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits or where it can fall into such power lines or circuits When installing an outside antenna system extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal USE 1 Accessories To avoid personal injury Do not place this product on an unstable cart stand tripod bracket or table It may fall causing serious injury to a child or adult and serious damage to the product Use only with a cart stand tripod bracket or table recommended by the manufacturer or sold with the product Use a mounting accessory recommended by the manufacturer and follow the manufacturer s instructions for any mounting of the product Do not try to roll a cart with small casters across thresholds or deep pile carpets EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE ANSI NFPA 70 ANTENNA I LEAD IN WIRE GROUND CLAMP ANTENNA DISCHARGE UNIT NEC SECTION 810 20 GROUND CLAMPS POW
15. key 1 and or 4 STOP Number key 2 and or 5 DATE amp Number key 3 and or 6 CH 6 DAILY M F Number key 8 WEEKLY Number key 9 and or SP EP when the Program screen on which you want to make changes is shown then press OK or gt If the overlap is not yet solved the conflicting programs will be shown on the Program check screen Repeat the above steps again PR START STOP CH DATE PROGRAM 4 10 SP 10 Other Functions J e e Timer warning display A warning appears on the TV screen to tell you that the timer recording is to start in 5 minutes if you are not in the timer recording standby mode at that time Press TIMER to put the VCR into timer recording standby mode To clear the display press CANCEL on the Remote WARNING TIMER RECORDING TO START SOON Checking tape position When you change the VCR operation mode from the stop mode to fast forward or rewind mode or when you perform an Index Search or Instant Review the tape REMAIN 1 00 eae COUNT 1 23 45 position indicator appears The position of in relation to B Beginning or E End shows you where you are on the tape Set SUPERIMPOSE to ON F pg 12 gt gt B F E Changing display information Each time you press DISPLAY the display panel shows the channel number and the clock time alternatively You can ch
16. on the Remote to select the desired monitor sound F pg 8 E S VHS MODE ON OFF You can determine which recording mode either S VHS mode or VHS mode is used for recording on S VHS tapes When this function is set to ON you can record on S VHS tapes with S VHS picture quality When this function is set to OFF you can record on S VHS tapes with VHS picture quality NOTES S VHS mode allows you to make high quality video recordings with horizontal resolution of 400 lines comparing with the 230 lines of resolution of conventional VHS recordings To achieve the highest quality picture we recommended to record in S VHS mode But remember that a conventional VHS VCR without SQPB cannot play back S VHS tapes recorded in S VHS mode S VHS MODE setting does not affect recording on VHS tapes Recording on VHS tapes is always performed in VHS mode except when using S VHS ET mode F pg 11 i FRONT AUX INPUT VIDEO S VIDEO You have to select which terminal either VIDEO composite or S VIDEO Y C separate signals to use as the video input terminal on the front panel Make sure you select the correct terminal otherwise you may fail in recording editing on this VCR 12 Editing You can use your VCR as the playback or recording VCR You can use a camcorder as the playback VCR and your VCR as the recording VCR Refer also to the other components instruction manuals for conn
17. to watch the third one press REVIEW three times The Instant Review function will also operate if the VCR is turned on Skipping unwanted portions Skip Search Press SKIP SEARCH on the Remote once to 4 times during playback Each press initiates a 30 second period of high speed playback up to 2 minutes When the specified portion of the tape is skipped normal playback resumes automatically To return to normal playback during Skip Search press PLAY P gt Recording It may be unlawful to record or play back copyrighted material without the consent of the copyright owner Accidental erasure prevention To prevent accidental recording on a recorded cassette remove its record CES safety tab To record on it later cover N Record safety tab the hole with adhesive tape Basic Recording Turn on the VCR and TV and select the VCR channel or AV mode El Load a cassette Make sure the record safety tab is intact If not cover the hole with adhesive tape before inserting the cassette The VCR turns on and the counter on the on screen display is reset automatically FA Select recording channel On the Remote Press CHA V or the Number keys On the VCR Press PAUSE CH The channel display on the S IM display panel starts blinking While the display is TW blinking press FF CH or REW CH to select channel After about 5 seconds the channel display stops blinking g n NOTES
18. AUTO PICTURE is OFF NORM will appear instead of AUTO EDIT Minimizes picture degradation during editing recording and playback SOFT Reduces image coarseness when viewing overplayed tapes containing much noise SHARP Clearer sharper edged picture when viewing images with much flat same colored surfaces such as cartoons NOTE Select EDIT when you are editing tapes After you finish editing the tapes select AUTO AUTO TIMER ON OFF When this function is set to ON The timer recording standby mode is automatically engaged when the VCR is turned off It is temporarily canceled when the VCR is turned on You do not have to press TIMER to engage or disengage the timer recording standby mode When this function is set to OFF You have to press TIMER to engage or disengage the timer recording standby mode CONTINUED ON NEXT PAGE i SUPERIMPOSE ON OFF When this function is set to ON various VCR status information on screen display appears on the screen NOTE When you use this VCR as the playback VCR for editing a tape be sure to set this function to OFF otherwise the VCR status information on screen display will be recorded on the edited tape E AUTO SP EP TIMER ON OFF When this function is set to ON the VCR automatically switches to EP mode to allow complete recording if there is not enough tape to record the entire program
19. ER SERVICE GROUNDING ELECTRODE SYSTEM NEC ART 250 PART H NEC NATIONAL ELECTRICAL CODE 2 PORTABLE CART WARNING Symbol provided by RETAC 2 Product and Cart Combination A product and cart combination should be moved with care Quick stops excessive force and uneven surfaces may cause the product and cart combination to overturn 3 Water and Moisture Do not use this product near water for example near a bath tub wash bowl kitchen sink or laundry tub in a wet basement or near a swimming pool and the like 4 Object and Liquid Entry Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock Never spill liquid of any kind on the product 5 Attachments Do not use attachments not recommended by the manufacturer of this product as they may cause hazards 6 Cleaning Unplug this product from the wall outlet before cleaning Do not use liquid cleaners or aerosol cleaners Use a damp cloth for cleaning 7 Heat The product should be situated away from heat sources such as radiators heat registers stoves or other products including amplifiers that produce heat SERVICING 1 Servicing If your product is not operating correctly or exhibits a marked change in performance and you are unable to restore normal operation by following the detailed procedure in its operating instructions d
20. JVC iin Sic LPT0733 001A COPYRIGHT 2002 VICTOR COMPANY OF JAPAN LTD Dear Customer Thank you for purchasing the JVC S VHS video cassette recorder Before use please read the safety information and precautions to ensure safe use of your new VCR CAUTIONS CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance SMIS Super VHS ET hiro INSTRUCTIONS Printed in China US 1102 MNV gt KPJKBJ NOTE Change or modifications not approved by the party responsible for compliance could void the user s authority to operate the equipment This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and ca
21. R after the power failure this VCR starts the Plug amp Play setting automatically to restore the clock time and channel setting If the clock time and channel setting are restored correctly each timer program you have made will start at its start time unless its end time has elapsed e If the tape reaches its end during timer recording the recording stops and O and gt on the display panel blink Press TIMER to disengage timer then press STOP EJECT amp on the VCR to eject the cassette or press POWER then press REW 44 to rewind the tape VCR has auto timer feature pg 11 Express Timer Programing Load a cassette with the record safety tab intact The VCR turns on and the counter is reset automatically Hl Press PROG on the Remote to access the Program screen FA Press START Number key 1 and or 4 STOP Number key start 2 and or 5 DATE Number key 3 and or 6 or CH repeatedly to enter the start time stop time date or channel Press and hold START or STOP to increase the time in 30 minute intervals To set the tape speed press SP EP To timer record daily Monday Friday or weekly serials press DAILY M F Number key 8 or WEEKLY Number key 9 Pressing the button again makes the DAILY or WEEKLY display disappear Press OK or PROG If PROGRAM NOT COMPLETED PROGRAM OVERLAP
22. S S VIDEO connection Original picture quality of S VHS made can be duplicated with minimal picture degradation This is the best editing method you can use on S VHS VCRs 13 Specifications GENERAL Power requirement Power consumption Power on Power off Temperature Operating Storage Operating position Dimensions W x Hx D Weight Format Maximum recording time SP EP AC 120 Va 60 Hz 16W 1 5 W 5 C to 40 C 41 F to 104 F 20 C to 60 C 4 F to 140 F Horizontal only 435 mm x 94 mm x 248 mm 17 3 16 x 3 3 4 x 9 3 4 2 7 kg 5 9 Ibs S VHS VHS NTSC standard 210 min with ST 210 video cassette 630 min with ST 210 video cassette VIDEO AUDIO Signal system Recording Playback system Signal to noise ratio Horizontal resolution VHS S VHS Frequency range Normal audio Hi Fi audio Input Output NTSC type color signal and EIA monochrome signal 525 lines 60 fields DA 4 Double Azimuth head helical scan system 45 dB 230 lines 400 lines 70 Hz to 10 000 Hz 20 Hz to 20 000 Hz RCA connectors IN x 1 OUT x 1 S video connectors IN x 1 OUT x 1 TUNER Tuning system Channel coverage VHF Frequency synthesized tuner Channels 2 13 UHF Channels 14 69 CATV 113 Channels RF output Channel 3 or 4 switchable preset to Channel 3 when shipped 75 ohms unbalanced TIMER Clock reference Program
23. UNCTION SET TUNER SET INITIAL SET PRESS a v THEN OK PRESS MENU TO END FA Access Manual Channel Set screen Press AV to move the highlight bar arrow to MANUAL CHANNEL SET then press OK or gt TUNER SET BAND AUTO CHANNEL SET MANUAL CHANNEL SET SELECT WITH A Y AND OK PRESS MENU TO END Add or skip desired channels To add channels MANUAL CHANNEL SET GATY Press the Number keys on the Remote CH 45 ADD 7S to input a channel number you want to add PRESS NUMBER KEY 0 9 7 OR asv THEN foo Press OK or gt to set to ADD PRESS MENU TO ENI Repeat 1 to 2 to add other channels Press MENU to return to normal screen To skip channels Press AV or the Number keys to select a channel number you want to skip Press OK or gt to set to SKIP Repeat and 2 to skip other channels Press MENU to return to normal screen rm rm After a power failure occurs band selection will be reset to CATV Playback Basic Playback Turn on the VCR and TV and select the VCR channel or AV mode E Load a cassette al ae 66 6660 0O10 a 5 2 aya Make sure the window side is up the rear label side is facing you and the arrow on the front of the cassette is pointing towards the
24. and above which are covered on an in home basis WHAT YOU MUST DO FOR WARRANTY SERVICE Return your product to a JVC authorized service center with a copy of your bill of sale For your nearest JVC authorized service center please call toll free 800 537 5722 If service is not available locally box the product carefully preferably in the original carton and ship insured with a copy of your bill of sale plus a letter of explanation of the problem to the nearest JVC Factory Service Center the name and location of which will be given to you by the toll free number If you have any questions concerning your JVC Product please contact our Customer Relations Department WHAT IS NOT COVERED This limited warranty provided by JVC does not cover 1 Products which have been subject to abuse accident alteration modification tampering negligence misuse faulty installation lack of reasonable care or if repaired or serviced by anyone other than a service facility authorized by JVC to render such service or if affixed to any attachment not provided with the products or if the model or serial number has been altered tampered with defaced or removed Initial installation and installation and removal for repair Operational adjustments covered in the Owner s Manual normal maintenance video and audio head cleaning Damage that occurs in shipment due to act of God and cosmetic damage Signal reception problems and failures due
25. ange display in the stop or recording T mode or during rewind fast forward HT When SUPERIMPOSF is set to ON pg 12 and DISPLAY on the Remote is pressed time counter and tape remaining time will appear on the TV screen To reset the time counter press C RESET on the Remote 2E E co z Function settings You can use the other useful function settings on the Function Set screen Turn on the VCR and TV and select the VCR channel or AV mode El Access Main Menu screen then MAIN MENU Function Set screen Press MENU on the Remote Press AV to move the highlight bar arrow to FUNCTION SET then press OK or PA Select Function Press AV to move the highlight bar arrow to the function you want to set FUNCTION SET TUNER SET INITIAL SET PRESS A W THEN OK PRESS MENU TO END FUNCTION PREVIOUS PAGE gt S VHS ET VIDEO STABILIZER OFF AUTO PICTURE ON BLUE BACK ON PICTURE CONTROL AUTO 2ND AUDIO RECORD OFF AUTO TIMER OFF AUDIO MONITOR HI FI SUPERIMPOSE S VHS MODE ON FRONT AUX INPUT VIDEO ON AUTO SP EP TIMER OFF NEXT PAGE SELECT WITH 4 7 AND OK SELECT WITH 4 w AND OK PRESS MENU TO END PRESS MENU TO END Change setting Press OK or The default setting is bold in the table below Press MENU to return to normal screen After a power failure occurs some Function Settings will be reset to its default setting E S VHS ET
26. appears see Program overlap warning display C pg 10 EJ Press TIMER The VCR turns off automatically and is displayed on the display panel H To stop timer recording press TIMER then STOP W PROGRAM 1 PRESS SP EP 8 DAILY 9 WEEKLY THEN 0K PRESS PROG TO END To use the VCR while it is in timer recording standby mode Press TIMER then press POWER I After you use the VCR press TIMER again to put the VCR into timer recording standby mode Checking canceling or changing program settings El Disengage timer Press TIMER then press POWER 0 1 When AUTO TIMER is set to ON C pg 11 you do not have to press TIMER FA Access Program Check screen Press PROG CHECK E Access Program screen Press PROG CHECK again Each time you press PROG CHECK the next program s Program screen appears Z3 Cancel or change program setting To cancel a program press CANCEL when the Program screen you do not want is shown To change a program press the appropriate button START Number key 1 and or 4 STOP Number key 2 and or 5 DATE Number key 3 and or 6 CH DAILY M F Number key 8 WEEKLY Number key 9 and or SP EP when the Program screen on which you want to make changes is shown PR START STOP CH 8 00P 10 00 12 10 00A 10 45 40 11 30P 1 00 125 1 2 3 4 5 6 7 8 PRESS CHECK TO NEXT E Re
27. ate manual tracking FA Press CHA V to eliminate the noises Press it briefly for a fine adjustment or press and hold for a coarse adjustment Press SP EP again to reactivate automatic tracking Selecting monitor sound Audio Monitor While playing back a tape on which stereo sound or SAP sound is recorded press AMONITOR on the Remote Each time you press the button sound changes HI Fl Normally select this Hi Fi sound is played back HI FI L Sound on the left Hi Fi channel is played back HI FI R Sound on the right Hi Fi channel is played back NORM Sound on the normal track is played back NORM HI FI Both sounds on the Hi Fi track and normal track are mixed and played back NOTE The above indication appears when SUPERIMPOSE is set to ON F pg 12 though the monitor sound changes in sequence Automatic operations after rewinding Next Function Memory The Next Function Memory tells the VCR what to do after rewinding is complete Ensure that the VCR is in stop mode For Automatic Playback Start Press REW lt then press PLAY B gt within 2 seconds For Automatic Power Off Press REW lt lt then press POWER I within 2 seconds For Automatic Timer Standby Press REW lt then press TIMER within 2 seconds NOTE It is not possible to select the Automatic Timer Standby function if the cassette s record safety tab is removed Playing back tape repeatedly
28. ce that is unstable or subject to vibration DO NOT block the VCR s ventilation openings DO NOT place heavy objects on the VCR or on the Remote DO NOT place anything which might spill on the top of the VCR or on the Remote 5 AVOID violent shocks to the VCR during transport Se For Customer Use Enter below the Model No and Serial No which are located on the rear of cabinet Retain this information for future reference Model No Serial No SVS ast Cassettes marked S VHS and VHS can be used with this video cassette recorder However S VHS recordings are possible only with cassettes marked S VHS By using S VHS ET it is possible to record and play back with S VHS picture quality on VHS cassettes with this VCR As an ENERGY STAR Partner JVC has determined that this product or product model meets the ENERGY STAR guidelines for energy efficiency IMPORTANT PRODUCT SAFETY INSTRUCTIONS Electrical energy can perform many useful functions But improper use can result in potential electrical shock or fire hazards This product has been engineered and manufactured to assure your personal safety In order not to defeat the built in safeguards observe the following basic rules for its installation use and servicing ATTENTION Follow and obey all warnings and instructions marked on your product and its operating instructions For your safety please read all the safety and operating instructi
29. e recording mode Channel and VCR operation auxiliary input Timer warning display mode Day and lra e clock time THU 12 00 AM PAUSE STEREO WARNING 00 SP Tape speed STEREO f SAP TIMER RECORDING SAP indication TO START SOON Cassette mark P gt CANCEL J SAP B e oie Ef Tape position indication INDEX it Audio NORM REMAIN 10 oJ II Index number monitor LHI Fl COUNT 1 28 45 S tape indications r mainingitime Time counter To recall an indication Press OSD OK e All indications corresponding to the current status are displayed for 5 seconds After that the counter information and RECORD PAUSE if in the Record Pause mode are left displayed on the screen Press OSD OK again to clear the display The RECORD PAUSE indication is left displayed on the nm screen Connections and Plug amp Play Setting El Check contents Make sure the package contains all of the accessories listed in Specifications F pg 14 PA Situate VCR Place the VCR on a stable horizontal surface Connect VCR to TV Antenna or cable fe Coaxial Matching transformer g not supplied Flat feeder AC power cord Back of VCR AC outlet To audio video on input connectors Audio video cable not supplied To 75 terminal E To S video input connector
30. east 20 cm 7 or 8 inch away from a TV DO NOT place the VCR close to a TV as it may cause noise picture disturbance or malfunctions power off etc to occur Buttons Connectors and Indicators Front Panel STOP EJECT S VIDEO H A Cassette loading slot input connector PLAY gt VIDEO AUDIO input connectors sensor POWER FF e on REWE CH CH Display panel Timer mode indicator VCR mode Play indicator indicator S VHS Record indicator indicator Channel and auxiliary input Clock time Rear Panel AC power cord oP vIDED OUT l ANT IN AUDIO VIDEO OUT TV OUT Remote a TV POWER ar POWER A MONITOR TV INPUT Ie mo un TVIVOR as DISPLAY WAN lt lt 2 A Number keys START START STOP DATE DATE Ae 5 jel 6 DAILY M F stop 6 6 aae BaT WEEKLY 1 CANCEL E ues o C RESET L CANCEL a i p ome SP EP x GBPROG CHECK SP EP SEARCH PROG E SEARCH PROG CHECK F PLAY REW E FF REC PAUSE STOP CHa v 0 9 TV CH TV VOL Kd gt lt gt REVIEW r A ae venu _I Si ENTER OSD JVG On screen display If you press OSD OK on the Remote when SUPERIMPOSE is set to ON F pg 12 you can see the current VCR status on the TV screen The indications are not recorded even if the VCR is in th
31. ection Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to cords at plugs convenience receptacles and the point where they exit from the product 5 Ventilation Slots and openings in the cabinet are provided for ventilation To ensure reliable operation of the product and to protect it from overheating these openings must not be blocked or covered Do not block the openings by placing the product on a bed sofa rug or other similar surface Do not place the product in a built in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer s instructions have been adhered to 6 Wall or Ceiling Mounting The product should be mounted to a wall or ceiling only as recommended by the manufacturer ANTENNA INSTALLATION INSTRUCTIONS 1 Outdoor Antenna Grounding If an outside antenna or cable system is connected to the product be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built up static charges Article 810 of the National Electrical Code ANSI NFPA 70 provides information with regard to proper grounding of the mast and supporting structure grounding of the lead in wire to an antenna discharge unit size of grounding connectors location of antenna discharge unit connection to grounding electrodes and requirements for the
32. ection and its operations EB Make connections Example 1 When another VCR is VHS VCR This VCR To AUDIO VIDEO IN To AUDIO VIDEO OUT When using this VCR as the recording VCR connect this VCR s AUDIO VIDEO IN connectors to the When using this VCR as the playback VCR connect this VCR s AUDIO VIDEO OUT connectors to the audio video input connectors on another VCR audio video output connectors on another VCR To audio video input To audio video output Another VCR e If another VCR is monaural connect this VCR s AUDIO L IN or OUT connector to the audio output or input connector on another VCR Example 2 When another VCR is S VHS VCR and equipped with S VIDEO input connector This VCR for playback To AUDIO OUT t t t To S VIDEO OUT Audio cable not supplied S video cable not supplied U To video input J 4 af To S video input Another VCR for recording Example 3 When another VCR is S VHS VCR and when using this VCR as the recording VCR This VCR for recording To AUDIO input FF t To S VIDEO input Audio cable not supplied S video cable not supplied To audio output J Another VCR for playback To S video output FA Load cassettes Insert the playback cassette into the playback VCR and the cassette to be recorded on into the recording VCR E Select input mode on recording VCR Select the correct
33. ing condition How to use the Remote Before use insert the lithium battery CR2032 correctly with the plus side up into the battery compartment To open it press the release tab and carefully pull the compartment out The Remote can operate most of your VCR s functions as well as basic functions of JVC TVs Point the Remote towards the remote sensor on the target component The maximum operating distance is about 8 m To operate a JVC TV use any of the following buttons TV POWER TV INPUT TV CH or TV VOL NOTE If the Remote does not work properly remove its battery wait for a few seconds replace the battery and then try again Video heads cleaning The heads get dirty in the following cases in an environment prone to extreme temperature or humidity in a dusty environment flaw dirt or mold on video tapes continuous usage for a long time Use a dry cleaning cassette TCL 2 when Rough poor picture appears while a tape is played back The picture is unclear or no picture appears USE CLEANING CASSETTE appears on the screen only with SUPERIMPOSE set to ON F pg 12 ATTENTION To mobile phone users Using a mobile phone in the vicinity of the VCR may cause picture vibration on the TV screen or change the screen to a blue back display On placing the VCR Some TVs generate strong magnetic fields Make sure to place the VCR at l
34. ls will be set automatically The time and date can be set automatically by the clock setting data transmitted from one of the regular TV broadcast channels We call this TV channel the host channel and it is a PBS channel in your area ATTENTION If you use a cable box Plug amp Play will not function set the clock and tuner channels separately gt pg 6 7 Depending on areas or reception conditions the VCR may not receive the Auto clock setting data from a PBS channel If this function is taking a considerable amount of time it may be necessary to perform the procedure in Semiauto Clock Set C pg 6 or Manual Clock Set pg 6 in m During Initial Auto Clock Set Me Aut blinks a N v um During Auto Channel Set ILI The channel numbers are displayed as they are v scanned and set 0 mm Plug amp Play Completed The current time is displayed What to do if Plug amp Play setting failed If an incorrect time is displayed on the display panel perform the procedure in Semiauto Clock Set pg 6 or Manual Clock Set F pg 6 f appears on the display panel ensure that the antenna cable is connected correctly Then turn on and off the VCR the Plug amp Play setting will be automatically reactivated If Plug amp Play setting is not performed though the antenna cable is connected correctly perform the procedure in Manual Clock Set F pg
35. n radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help WARNING TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE CAUTION This video cassette recorder should be used with AC 120V 60Hz only To prevent electric shocks and fire hazards DO NOT use any other power source CAUTION TO PREVENT ELECTRIC SHOCK MATCH WIDE BLADE OF PLUG TO WIDE SLOT FULLY INSERT ATTENTION POUR EVITER LES CHOCS ELECTRIQUES INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHEDANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU AU FOND Caution on Replaceable lithium battery The battery used in this device may present a fire or chemical burn hazard if mistreated Do not recharge disassemble heat abo
36. nish or French Press AV to move the highlight bar arrow to LANGUAGE then press OK or gt repeatedly until the desired language is selected Press MENU to return to normal screen SELECT WITH ny AND 0K PRESS MENU TO END Language selection will be reset to ENGLISH after a power failure occurs Clock Setting Perform clock setting only if the clock has not been set correctly by the Plug amp Play setting or if you use a cable box Turn on the VCR and TV and select the VCR channel or AV mode Preparations MAIN MENU FUNCTION SET TUNER SET El Access Main Menu screen then Initial Set screen Press MENU on the Remote Press AV to move the highlight bar arrow to INITIAL SET then press OK or gt PRESS A Y THEN OK PRESS MENU TO END FA Access Clock Set screen Press AV to move the highlight bar arrow to CLOCK SET then press OK or gt INITIAL SET CLOCK SET LANGUAGE ENGLISH SELECT WITH Ti AND 0K PRESS MENU TO END Setting dock semiautomatically Semiauto Clock Set You can change the host channel D S T Daylight Saving Time time zone setting manually First follow steps Hl to A in Preparations above then go to the following steps NOTE The time set previously will be erased when AUTO CLOCK HOST CH D S T or TIME ZONE setting is changed El Set Auto Clock to ON CLOCK SET Press OK
37. o not attempt to service it yourself as opening or removing covers may expose you to dangerous voltage or other hazards Refer all servicing to qualified service personnel 2 Damage Requiring Service Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions a When the power supply cord or plug is damaged b If liquid has been spilled or objects have fallen into the product c If the product has been exposed to rain or water d If the product does not operate normally by following the operating instructions Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation e If the product has been dropped or damaged in any way f When the product exhibits a distinct change in performance this indicates a need for service 3 Replacement Parts When replacement parts are required be sure the service technician has used replacement parts specified by the manufacturer or which have the same characteristics as the original part Unauthorized substitutions may result in fire electric shock or other hazards 4 Safety Check Upon completion of any service or repairs to this product ask the service technician to perform safety checks to determine that the product is in safe operat
38. ons before you operate this product and keep this booklet for future reference INSTALLATION 1 Grounding or Polarization A Your product may be equipped with a polarized alternating current line plug a plug having one blade wider than the other This plug will fit into the power outlet only one way This is a safety feature If you are unable to insert the plug fully into the outlet try reversing the plug If the plug should still fail to fit contact your electrician to replace your obsolete outlet Do not defeat the safety purpose of the polarized plug B Your product may be equipped with a 3 wire grounding type plug a plug having a third grounding pin This plug will only fit into a grounding type power outlet This is a safety feature If you are unable to insert the plug into the outlet contact your electrician to replace your obsolete outlet Do not defeat the safety purpose of the grounding type plug 2 Power Sources Operate your product only from the type of power source indicated on the marking label If you are not sure of the type of power supply to your home consult your product dealer or local power company If your product is intended to operate from battery power or other sources refer to the operating instructions 3 Overloading Do not overload wall outlets extension cords or integral convenience receptacles as this can result in a risk of fire or electric shock 4 Power Cord Prot
39. ook NJ 07058 9641 ACCESSORIES Don t service the product yourself To purchase accessories for your JVC product you may contact your local JVC Dealer CAUTION To prevent electrical shock do not open the cabinet From the 48 Continental United States call toll free 1 800 882 2345 or on the web at www JVC com There are no user serviceable parts inside Please refer to qualified service personnel for repairs 15 WARRANTY Only in U S A LIMITED WARRANTYcoNSUMER VIDEO 1 90 JVC COMPANY OF AMERICA warrants this product and all parts thereof except as set forth below ONLY TO THE ORIGINAL PURCHASER AT RETAIL to be FREE FROM DEFECTIVE MATERIALS AND WORKMANSHIP from the date of original retail purchase for the period as shown below The Warranty Period PARTS LABOR TYR 90pays THIS LIMITED WARRANTY IS VALID ONLY IN THE FIFTY 50 UNITED STATES THE DISTRICT OF COLUMBIA AND IN COMMONWEALTH OF PUERTO RICO WHAT WE WILL DO If this product is found to be defective JVC will repair or replace defective parts at no charge to the original owner Such repair and replacement services shall be rendered by JVC during normal business hours at JVC authorized service centers Parts used for replacement are warranted only for the remainder of the Warranty Period All products and parts thereof may be brought to a JVC authorized service center on a carry in basis except for Television sets having a screen size 25 inches
40. or gt on the Remote repeatedly to ime g INE YEAR move the highlight bar to AUTO CLOCK mimarmem then press AV so that ON is selected DST HOSTCH 7AUT CATV S T AUTO TIME ZONE AUTO PRESS a v THEN OK PRESS MENU TO END FA Select host channel You can either select AUTO or enter a PBS channel number Press OK or gt to move the highlight bar to HOST CH then press AV repeatedly until AUTO or the desired PBS channel number is selected Some PBS channels do not transmit clock setting data EJ Select D S T mode Press OK or gt to move the highlight bar to D S T then press AV repeatedly until the desired setting is selected AUTO Select if you want to adjust your VCR s clock automatically by the incoming signal from the host channel Auto Daylight Saving Time enables automatic adjustment of the VCR s clock at the start and end of Daylight Saving Time Be sure to select the correct time zone manually in step ON Adjustment will be made by the built in clock itself OFF Select when Daylight Saving Time does not apply to you EJ Select time zone Press OK or gt to move the highlight bar to TIME ZONE then press AV repeatedly until AUTO or the desired time zone is selected Each time you press the button the time zone changes as follows AUTO gt ATLANTIC EASTERN CENTRAL MOUNTAIN gt PACIFIC ALASKA HAWAII gt
41. ssette Set S VHS ET to ON cF pg 11 Then insert a cassette marked VHS The S VHS indicator lights up on the front display panel e To record in VHS Insert a cassette marked VHS Set S VHS ET to OFF F pg 11 e To record in VHS on an S VHS cassette Insert a cassette marked S VHS The S VHS indicator lights up on the display panel Then set S VHS MODE to OFF F pg 12 The S VHS indicator goes off The VHS recording mode is selected NOTE When playing back a tape that has been recorded in S VHS or S VHS ET the S VHS indicator lights up on the display panel regardless of the S VHS ET or S VHS MODE setting i Timer Recording Up to 8 timer recording programs can be made using express timer programing method as far as a year in advance Remember the clock must be set before you can program the timer Turn on the VCR and TV and select the VCR channel or AV mode NOTES e If all the 8 programs have already been set PROGRAM FULL appears on the TV screen After timer recording is completed the VCR turns off automatically You can program the timer recording while a regular recording is in progress the menu screens will not be recorded Even if a power failure occurs the VCR keeps your timer programs However the clock time channel settings and other menu settings are lost As a result when the power is supplied again to this VC
42. the Hi Fi and normal tracks When this function is set to OFF the SAP audio cannot be recorded NOTES When the channel is changed on the VCR The STEREO indication appears on the screen for about 5 seconds if the program is a stereo broadcast The SAP indication appears on the screen for about 5 seconds if the program is a SAP broadcast Both indications appear when a stereo program is accompanied by SAP sound AUDIO MONITOR HI FI HI FI L HI Fl R NORM MIX This VCR can record two sound tracks simultaneously normal and Hi Fi on a Hi Fi stereo tape You can select the sound track s to listen to while playing back a Hi Fi stereo tape In addition when playing back a prerecorded tape containing two separate audio programs on the Hi Fi tracks you can choose either one by selecting either HI FI L or HI FI R HI FI Normally select this Hi Fi sound is played back HI FI L Sound on the left Hi Fi channel is played back HI FI R Sound on the right Hi Fi channel is played back NORM Sound on the normal track is played back MIX Both sounds on the Hi Fi track and normal track are mixed and played back NOTES While playing back a monaural tape sounds on the normal track will be heard regardless of this setting If RF connection t pg 5 is used for viewing pictures on the TV sound will be monaural even though you select HI FI You can also use the AAMONITOR button
43. to line power surge Video Pick up Tubes CCD Image Sensor Cartridge Stylus Needle are covered for 90 days from the date of purchase Accessories Batteries except that Rechargeable Batteries are covered for 90 days from the date of purchase There are no other express warranties except as listed above THE DURATION OF ANY IMPLIED WARRANTIES INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY IS LIMITED TO THE DURATION OF THE EXPRESS WARRANTY HEREIN JVC SHALL NOT BE LIABLE FOR THE LOSS OF USE OF THE PRODUCT INCONVENIENCE LOSS OR ANY OTHER DAMAGES WHETHER DIRECT INCIDENTAL OR CONSEQUENTIAL INCLUDING WITHOUT LIMITATION DAMAGE TO TAPES RECORDS OR DISCS RESULTING FROM THE USE OF THIS PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY ALL EXPRESS AND IMPLIED WARRANTIES INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE ARE LIMITED TO THE WARRANTY PERIOD SET FORTH ABOVE Some states do not allow the exclusion of incidental or consequential damages or limitations on how long an implied warranty lasts so these limitations or exclusions may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state JVC COMPANY OF AMERICA 1700 Valley Road DIVISION OF JVC AMERICAS CORP Wayne New Jersey 07470 REFURBISHED PRODUCTS CARRY A SEPARATE WARRANTY THIS WARRANTY DOES NOT APPLY FOR DETAILS OF REFURBISHED PRODUCT WARRANTY PLEASE REFER
44. turn to normal screen Press PROG CHECK repeatedly until no Program screen is shown E Reengage timer recording standby mode Press TIMER The VCR turns off automatically and is displayed on the display panel When AUTO TIMER is set to ON F pg 11 the timer recording standby mode automatically resumes when you turn off the VCR Program overlap warning display If PROGRAM NOT COMPLETED PROGRAM OVERLAP appears you have another program overlapping the program you have just made The Program Check screen appears and conflicting programs will start blinking PR START STOP CH DATE 8 00P 10 00 12 12 24 10 00A 10 45 40 12 255 PROGRAM NOT COMPLETED PROGRAM OVERLAP 11 30P 1 00 125 12 25 2 3 4 9 00P 10 00 10 12 24 5 gt 6 7 8 a v THEN p gt PROG END Example Program 1 you have just made and Program 4 overlap each other El Select program to modify Press AV then press OK or gt You can only select one of the overlapping programs If you do not mind this overlap press H PROG to finish the timer program a THEN p PROG END setting The program starting earlier or program with the lower program number will be recorded FA Cancel or change program setting To cancel a program press CANCEL when start the Program screen you do not want is J shown To change a program press the eee ai appropriate button START Number PRESS PROG TO END
45. ve 100 C or incinerate Replace battery with CR2032 Panasonic Matsushita Electric or Maxell is recommended Danger of explosion or Risk of fire if the battery is incorrectly replaced m Dispose of used battery promptly m Keep away from children m Do not disassemble and do not dispose of in fire Note to CATV system installer This reminder is provided to call the CATV system installers attention to Article 820 40 of the NEC that provides guidelines for proper grounding and in particular specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical Declaration of Conformity Model Number HR S1902U Trade Name JVC Responsible Party JVC Americas Corp Address 1700 Valley Road Wayne N J 07470 Telephone Number 973 317 5000 This device complies with Part 15 of FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Failure to heed the following precautions may result in damage to the VCR Remote or video cassette 1 DO NOT place the VCR in an environment prone to extreme temperatures or humidity in direct sunlight in a dusty environment in an environment where strong magnetic fields are generated on a surfa
46. while timer recording in SP mode For Example Recording a program of 140 minutes in length onto a 120 minute tape Approximately 110 minutes Approximately 30 minutes SP mode EP mode NOTES If you have programed the VCR to timer record 2 or more programs do not use this function but change the tape speed manually during timer programing There may be some noise and sound disturbance where the tape speed switches from SP to EP mode on the tape This function is not available during ITR Instant Timer Recording and will not work properly on the following tapes T ST 30 T ST 60 T ST 90 and T ST 120 VIDEO STABILIZER ON OFF When this function is set to ON you can automatically correct vertical vibrations in the picture when playing back unstable recordings made on another VCR NOTE To watch recordings with close caption or when you finish viewing a tape set this function to OFF E BLUE BACK ON OFF When this function is set to ON the TV screen becomes all blue when receiving a channel not in use NOTE When you want to receive an unstable channel with poor signals set this function to OFF E 2ND AUDIO RECORD ON OFF When this function is set to ON If a SAP program is received the SAP audio is recorded on both the normal and Hi Fi tracks The main audio is not recorded If a non SAP program is received the main audio is recorded on both
Download Pdf Manuals
Related Search