JVC HR-P111AG User's Manual
Contents
1. 1 Load a blank video tape 2 Press SP LP EP 4 to set the recording speed Press to start recording On the remote control unit press and gt at the same time The recording indicator will light during al B E S T takes place at the beginning of each first SP and first LP or EP recording after inserting the cassette E Press m amp on the video cassette player on the remote control press W to stop recording To stop recording temporarily E Press II The recording indicator will blink Press to resume recording NOTES e To engage recording standby press and then press Hl The STAN D BY REC indicator will blink during recording standby Press gt again to start recording e f does not work check to see if the cassette safety tab has been removed The player automatically stops when record standby continues for more than 5 minutes The video tape will be rewound automatically when the end of the tape is reached B E S T picture system The B E S T Biconditional Equalized Signal Tracking system checks the condition of the tape in use during recording and playback and compensates to provide the highest possible recording and playback pictures The default setting for both recording and playback is ON Recording The video cassette player assesses the quality of the tape once you initiate recording WE Th2. 2 0 Vp p 75 ohms unbalanced Line output level s cacecwases 1 0 Vp p 75 ohms unbalanced SUN Tall Out aa a tas More than 45 dB Horizontal resolution More than 250 lines PAL MESECAM More than 220 lines NTSC Audio Line input level wi execiewnse 8 dBs 50 k ohms unbalanced Line output level 8 dBs 1 k ohm unbalanced Frequency response 70 Hz to 10 000 Hz Normal audio Power requirements RAUNG aenur AC 110 V 240 V 50 Hz 60 Hz ODE AUING aeo ara a Aa Eae riiai AC 90 V 260 V 50 Hz 60 Hz Power Consumption 068 12 W Operation temperature 5 C to 40 C DIMENSIONS ceceeseeceeeeeeees 360 mm W x 98 mm H x 255 mm D Wein ME mesai ai ia 2 9 kg Standard accessories Remote control unit 1 Batteries for remote control 2 RF antenna cable ossee 1 Conversion plug nsss 1 Not provided in certain areas Design and specifications subject to change without notice Printed in China 0604DYR NF BJ COPYRIGHT 2004 VICTOR COMPANY OF JAPAN LTD
3. Jve MW ENGLISH CONTENTS Features viscvccnisasssceandoranieaaekoaads 2 VIDEO CASSETTE PLAYER Automatic features 2 WITH LINE RECORDING PreCaUtiONs ccceceececeeceeeess 3 SEa ELLE EE 4 Wireless remote control 5 On screen display 066 6 CONNECTIONS eeeeeeeee eens 6 Setting the video channel 8 HR P 1 1 1 AG Mode set 9 Setting Of The Colour System Select Buttons ssseseeeeeeeen 10 H R P1 1 OAS Playback 11 Recording 13 B E S T picture system 13 FCC cect nia ete aeateuensacanceastenes 14 Troubleshooting 15 Specifications esseeeee 16 VHS PAL NTSC Thank you for purchasing this JVC video cassette player To ensure optimum performance of this unit please read this instruction manual thoroughly Only cassettes marked VHS can be used with this video cassette player 2 Features Features 3 system PAL MESECAM NTSC NTSC playback on PAL television RF output G K switchable Digital auto tracking HQ High Quality Auto playback function Repeat playback Shuttle search Still and slow motion Line recording B E S T Biconditional Equalized Signal Tracking picture system Automatic features Auto power on The video cassette player is automatically turned on when the tape is inser
4. Still picture and frame advance Use this feature to freeze the playback picture and to advance one frame at a time The sound will be cut during this mode During playback 1 Press II The picture will be frozen 2 Press II repeatedly to advance frames Each time the button is pressed the still picture will advance one frame W Press gt to resume normal playback NOTES e f the picture shakes during the still mode use TRACKING to correct the picture e After the picture has been frozen for approx 5 minutes the still mode will disengage to protect the video tape 12 Playback Shuttle search playback Use this feature during playback to visually locate any point on a recorded cassette The sound will be cut during shuttle search operation During playback i Press gt gt or lt lt to engage shuttle search forward or reverse E Press gt gt to lt lt again to perform high speed NOTE Each time you press gt or lt 4 the search speed changes between low speed and high speed Tracking adjustment Automatic tracking is adjusted each time a cassette is inserted in the video cassette player you may wish to adjust tracking manually during playback Manual tracking H Press the remote control s AUTO Press the remote control s TRACKING or to adjust tracking HM Press AUTO to return to automatic tracking Counter reset HE Press 0000 to reset the counter
5. Install this VCP a little way apart from the TV set Remote control does not function The batteries are weak Replace the batteries Auto playback does not function The video cassette s recording safety tab has not been removed Recording does not function Are the connections correct Was the Record button pressed The video cassette s recording safety tab is removed The video cassette player does not Microcomputer malfunction function properly Disconnect the power plug from the AC outlet and then re insert it The microcomputer will be reset to its initial mode About Head cleaning W If the picture playback becomes blurred it does not mean that the recorded program has been erased E Dirt accumulated on the video heads after long periods of use causes such troubles In this case head cleaning requiring highly technical care is necessary E For head cleaning consult the nearest JVC dealer 16 Specifications Specifications FOPMA R eepo aa VHS Standard Video recording system Rotary slant azimuth helical scan system Rotary heads onair ias 2 video heads RE DUDUT snow intinsa System B G D K type modulation UHF ch 32 40 adjustable preset ch 36 Recording line input PAL SECAM MESECAM tape NTSC 3 58 NTSC 4 43 Playback line output PAL SECAM MESECAM tape NTSC 3 58 NTSC 4 43 Simulated PAL NTSC tape Video Line input level cc03 cs csees e0200 0 5
6. Repeat playback Use this feature to repeat playback of a cassette 100 times During playback 1 Press gt for more than 5 seconds The Play indicator will blink slowly and playback of the cassette will repeat 100 times automatically 2 Press W to stop repeat playback Tape playback will be ee and the repeat playback mode will be cancelled NOTE Pressing gt lt lt gt gt or II also stops repeat playback Rewind playback or power off When the tape has finished rewinding the Video cassette player will playback or turn itself off During stop a For Automatic Start Of Playback Press lt 4 then press gt within 2 seconds b For Automatic Power Off Press lt lt then press O I within 2 seconds ATTENTION In the search still slow motion or frame advance mode e the picture will be distorted e the noise bars will appear e there will be loss of colour e the picture may not appear However this is not malfunction Recording 13 Recording Use the following procedure to record TV programmes on a blank video tape Before proceeding To record TV programmes the video cassette player must be connected to the TV as shown in connection B of the Connections on page 6 section Turn on the power of the TV and video cassette player Make sure that the video cassette s safety tab is intact If it has been removed cover the hole with adhesive tape
7. connected between the antenna and the TV video cassette player s ANT IN terminal antenna cable to the video cassette player s RF OUT terminal and the other end to the TV s antenna terminal Connect the power cord to your household AC outlet 1 Connect your TV antenna cable to the 2 Connect one end of the provided RF Connection B For connection of a TV that has VIDEO AUDIO IN OUT terminals This connection is necessary to record TV programmes Use RCA type pin connection cords available from audio video stores for connection This connection is in addition to connection A 1 Follow steps 1 and 2 of Connection A 2 Connect the TV s VIDEO OUT and AUDIO OUT terminals to the video cassette player s VIDEO IN and AUDIO IN terminals Connect the TV s VIDEO IN and AUDIO IN terminals to the VCP s VIDEO OUT and AUDIO OUT terminals 4 Connect the power cord to your household AC outlet 8 Setting the video channel Setting the video channel To watch videos on your TV it must be set to the same UHF channel as the video cassette player This channel is used as the video channel This video cassette player has been preset to UHF channel 36 NOTE When you have connected the VIDEO AUDIO OUT terminals of this video cassette player to your TV s video audio in terminals connection B of the Connections section setting the video channel is not necessary In this case simply set th
8. one recorded on another video player set B E S T to on or off to your preference Editing Editing To From Another Recorder Player Audio Video signals Recorder TV Receiver CHANNEL BT connect the player s AUDIO and VIDEO OUT connectors to the recorder s AUDIO and VIDEO IN connectors 2 Put the player in the Play mode Put the recorder in the Record mode NOTES NTSC tapes being played back in the NTSC PLAYBACK ON PALTV mode cannot be dubbed to another recorder When you dub an NTSC tape using your recorder as the playback deck select NTSC 3 58 or 4 43 with the Colour System O utput switch Important W To edit both the player and the recorder must be of the same colour system Set NTSC to appropriate mode See Mode set CF pg 9 Troubleshooting 15 Troubleshooting No power Is the power cord plugged in Is the power turned on Tape cannot be ejected Was the video cassette player s m button or the amp EJECT button on the remote control pressed No picture Is the TV set to the video channel Is a cassette loaded Are the connections correct No colour Set the Colour System Output switch according to the recorded tape system Shuttle search does not function Is the video cassette player in the playback mode Disturbances in playback picture Is tracking adjusted properly Is the TV adjusted properly
9. e TV s TV VCR switch to VCR IMPORTANT Before performing the following steps make sure the player s power is off and there is no cassette inserted in the player 1 Access video channel set mode T N Hold down W amp on the video As Fy cassette player until both of the POWER ON and STANDBY REC indicators light POWER ON STANDBY REC indicator indicator 2 Set video channels TANDBY REC N Set your TV to UHF channel 36 TEST SIGNAL f the two vertical white bars appear The channel on clearly on the screen as shown in the which the screen to illustration on the right go to step 3 the left appear f the two vertical white bars do not Clearly in step 2 is appear Clearly press TRACKING or your Video Channel to set the video cassette player to a vacant channel between 32 and 40 which is not occupied by any local To view picture signals from the video player set station In your area your TV to the Video Channel The mode indicators tell channel position POWER ON STANDBY REC Blinking The indicators blink different speed 1 red Speed by the channel position as shown on bik fast the right E manta a aSa blink Press OK 0 nE STANDBY REC indicator goes off In tga EY set Tv system Set RF OUT to B G or D K See Mode set I pg 9 blink a Mode set Mode set You can change various mode setting on the Mode Set screen by fo
10. e player spends approximately 7 seconds assessing the condition of the tape then begins recording 14 Editing NOTES The B E S T system works only after a tape has been inserted and the Record mode is first initiated It does not work during recording Once the cassette is ejected the B E S T data is cancelled The next time the cassette is used for recording B E S T is re performed ATTENTION Since the B E S T system works before recording actually starts there is a delay of approximately 7 seconds after and gt on the remote are pressed or on the player is pressed To make sure you record the desired scene or programme in its entirely first perform the following steps 1 Press and hold II and to engage the Record Pause mode e The player then automatically check the condition of the tape and after approximately 7 seconds reenters Record Pause 2 Press to start recording e If you want to bypass the B E S T system and begin recording immediately set B E S T to OFF Playback The video cassette player assesses the quality of the tape once you initiate playback When watching a tape recorded with B E S T set to on it is recommended that you leave B E S T on during playback as well W The player adjusts the playback picture quality based on the quality of the tape in use WE B E S T is active during Auto Tracking NOTE When watching a rental tape or
11. em for recording and playback lt pg 10 O I button To turn the power on and off standby mode 9 AC power cord RF OUT terminal AUDIO VIDEO IN terminals AUDIO VIDEO OUT terminals ANT IN terminal Wireless remote control Wireless remote control When using the remote control for operation of the video cassette player make sure that it is pointed at the remote sensor window You can also use the player s remote control to operate a JVC television AUTO TRACKING sI E Transmitting window ol button To turn the power on and off standby Il PAUSE button To freeze the picture during playback Also to engage the recording pause mode O lt lt O button To rewind the video tape Also to start reverse shuttle search playback REC button Press the REC to start recording O AUTO button To enable disable auto tracking mode SP LP EP button e To select the recording tape speed e To select JVC TV s sounds A V buttons To select the mode lt gt buttons To set the mode MENU button To access Mode Set screen button To start playback gt gt button To fast forward the video tape Also to start forward shuttle search playback E button To stop playback 0000 button To reset the tape counter A EJECT button Press the amp
12. llowing procedure described below i Access the Mode Set screen Press MENU gt 0 8 D 2 Select the mode RF OUT Press A to move the pointer to the item you want to change Vl I P i Select the mode setting Press lt P gt 4 Return to the normal screen Press MENU E RFOUT B G New Zealand Kuwait U A E Indonesia Singapore Thailand Malaysia Iran Saudi Arabia D K Egypt Morocco Lebanon Iraq China Mongolia Russia MENU EXIT The default setting is bold in the table below When the function is set to ON various operational indicators appear on the TV screen NOTE When you use this video cassette player as the source player for editing be sure to set O S D to OFF before starting You can set the B E S T Biconditional Equalized Signal Tracking system to ON or OFF See B E S T picture system pg 13 Set appropriate TV system that matches the system of TV being used 10 Setting O f The Colour System Select Buttons Setting Of The Colour System Select Buttons Use the COLOUR SYSTEM button on the front panel to select the colour system Pressing the COLOUR SYSTEM displays the current setting on the screen While the current setting is displayed press COLOUR SYSTEM again to change the mode as illustrated below The On Screen display will show which mode is selected e f the mode is changed between different types of colour signa
13. ls the picture might be distorted at the switching point Mode Display AUTO NTSC 3 58 COLOUR SYSTEM NTSC 4 43 NTSC PAL PAL MESECAM Appears during playback only Description Usually set to this mode This mode automatically detects PAL NTSC 3 58 MESECAM and adjusts to the colour system being recorded or played back When it does not perform properly set the colour system manually For recording there is a choice of 4 selectable modes NTSC 3 58 NTSC 4 43 PAL MESECAM Select the mode that matches the colour signal being received For playback there is an additional mode which allows NTSC tapes to be played back and viewed on PAL TVs To record an NTSC 4 43 signal perform the following steps 1 Press and hold II and press to enter Recording Pause Mode Press COLOUR SYSTEM repeatedly and select NTSC 4 43 colour mode Press to start recording NOTES In the AUTO mode NTSC signals will be automatically recorded as NTSC 3 58 e In the AUTO mode NTSC tapes will be played back as NTSC 3 58 SECAM signals will always be recorded as MESECAM Select the AUTO or the MESECAM mode when recording SECAM signals e When playing back a SECAM tape select the AUTO or MESECAM mode The playback picture will always be monochrome In the NTSC 4 43 mode with some TVs on screen displays Program screen etc may roll up or down and there may bea los
14. r laws governing the disposal of these batteries must be followed strictly Failure to heed the following precautions may result in damage to the player remote control or video cassette player 1 DO NOT place the player in an environment prone to extreme temperatures or humidity in direct sunlight in a dusty environment in an environment where strong magnetic fields are generated on a surface that is unstable or subject to vibration 2 DO NOT block the player s ventilation openings or holes If the ventilation openings or holes are ploeked by a newspaper or cloth etc the heat may not be able to get out 3 DO NOT place heavy objects on the player or remote control 4 DO NOT place anything which might spill on top of the player or remote control If water or liquid is allowed to enter this equipment fire or electric shock may be caused 5 DO NOT expose the apparatus to dripping or splashing 6 DO NOT use this equipment in a bathroom or places with water Also DO NOT place any containers filled with water or liquids such as cosmetics or medicines flower vases potted plants cups etc on top of this unit 7 DO NOT place any naked flame sources such as lighted candles on the apparatus 8 AVOID violent shocks to the player during transport Beware of moisture condensation Moisture in the air will condense on the VCP when you move it from a cold place to a warm place or under extremely humid conditions ju
15. s of colour When this happens select the AUTO mode Playback Il Playback NTSC PAL and MESECAM video tapes can be played back on this video cassette player See Setting Of The Colour System Select Buttons on page 10 for details Before proceeding Turn on the power of the TV and video cassette player Make sure that the TV is set to the video channel or that the TV s TV VIDEO switch is set to VIDEO See Setting the video channel on page 8 for details AUTO e TRACKING 1 Load a pre recorded cassette If the safety tab on the cassette is removed playback will start automatically 2 Press gt to start playback B E S T PICTURE SYSTEM appears on the screen when B E S T is set to ON See Mode set CF pg 9 E Press M A or the remote control s W to stop playback Then press W amp to remove the cassette To fast forward or rewind the tape E From the stop mode press gt gt or lt lt Slow motion playback Slow motion playback is 1 6 of the normal playback speed The sound will be cut during slow motion playback During playback 1 Press Il for 2 seconds E Press gt to return to the normal playback speed NOTES f the picture shakes during the slow mode use TRACKING to correct the picture e After approx 5 minutes the slow mode will disengage to protect the video tape
16. st as water droplets form on the surface of a glass filled with cold liquid Moisture condensation on the head drum will cause damage to the tape In conditions where condensation may occur keep the VCP s power turned on for a few hours to let the moisture dry When transporting W Be sure to remove cassette from VCP before packing W Avoid violent shocks to the VCP during packing and transport CAUTION For HR P110AS only Use the conversion plug depending on the type of your AC wall outlet 4 Controls Controls Front Panel a SP LP EP button To select the recording tape speed Cassette loading slot Load the video cassette here Record button To start recording O gt Play button To start playback m Stop Eject button To stop playback and to eject the video tape O p gt Fast forward button To fast forward the video tape and to start forward shuttle search playback mode lt lt Rewind button To rewind the video tape and to start reverse shuttle search playback mode Rear Panel 12 jt Hy Remote sensor window For remote control operation STANDBY REC indicator e Lights when the power turns off Standby mode or during recording mode e Blinks during recording pause mode POWER ON indicator Lights when the power turns on COLOUR SYSTEM button To set the colour syst
17. ted Auto rewind The video tape is automatically rewound when the end of the tape is reached during the play recording or shuttle search forward mode Auto playback If the video cassette s safety tab has been removed playback will begin automatically when the tape is inserted into the video cassette player Power off eject Even when the video cassette player s power is off pressing the eject button will turn the power on and eject the tape Once ejected the power will be turned off again automatically Auto head cleaning When a tape is loaded or ejected the VCP video head is cleaned automatically Precautions W Precautions The rating plate and the safety caution are on the rear of the unit WARNING DANGEROUS VOLTAGE INSIDE WARNING TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE The button does not completely shut off mains power from the unit but switches operating current on and off This unit is produced to comply with Standard IEC 60065 The socket outlet shall be installed near the equipment and easily accessible or the mains plug or an appliance coupler shall remain readily operable When the equipment is installed in a cabinet or a shelf make sure that it has sufficient space on all sides to allow for ventilation 10 cm or more on both side on top and at the rear When discarding batteries environmental problems must be considered and the local rules o
18. to eject the cassette You also can eject the cassette when the player is turned off TRACKING buttons To adjust tracking during playback OK button e To fix the setting e To display the information on the television s display NOTES Point the remote control toward the remote sensor window e The maximum operating distance of the remote control is about 8 m When inserting the batteries be sure to insert in the correct directions as indicated under the battery cover f the remote control doesn t work properly remove its batteries wait a short time replace the batteries and then try again 6 On screen display On screen display When O S D is set to ON See Mode set CF pg 9 various operational indicators appear on the TV screen Operation mode indicators Tape speed SP LP EP Colour system indicator Tape direction Counter display O Tape position indicator Cassette loaded mark Connections Make sure that the power to the video cassette player and TV is off before making the following connections Connection A Connection B NOTE If you puta TV set directly on this Video cassette player or install it too close to a TV set noise may occur If this noise occurs separate the Video cassette player and the TV set Connections Connection A basic In order to use the video cassette player it must be
Download Pdf Manuals
Related Search