Johnson Hardware 1700SM User's Manual
Contents
1. 1718 1734 1738 1770 Series www johnsonhardware com e in g n Har are 1718 11 doors to 35 Ibs each 1734 34 doors to 35 Ibs each 1738 1344 doors to 35 Ibs each 1770 34 doors to 40 Ibs each OPENING ROUGH JAMB DOORS JAMB EDGE IN17FDSM HEAD JAMB FINISHED OPENING WIDTH i a 2 DOORS 2 x DOOR WIDTH X JA X Yq 4 DOORS 4 x DOOR WIDTH 4 s OE ECIAS STRIP FINISHED OPENING HEIGHT DOOR HEIGHT 4 2 FINISH JAMB a z lt x s I o z u FOR OPTIONAL FLOOR THRESHOLD TRACK INSTALLATION WRITE TO FACTORY FOR INSTRUCTIONS DIMENSIONAL REQUIREMENTS CHANGE FROM THOSE SHOWN HERE ROUGH JAMB 8 x 114 PAN HEAD SCREWS steel or aluminum door frames are used we strongly recommend the use of Molly Screws or toggle bolts in track holes on either side of Track Pivot Lock for added strength NOTE When light gauge hollow metal USE 8 x 54 SCREWS FRONT SIDE s IN TOP A LONE ONLY BACK SIDE UNTIL FINAL ADJUSTMENTS 1721 1926 ARE MADE 1724 1728 KNOB 1703 HINGES JAMB EDGE 1727 BOTTOM 1727 1729 1729 1773 1773 L E JOHNSON PRODUCTS INC 2100 STERLING AVE ELKHART IN 46516 USA 574 293 5664 1922 1926 1929 1972 ALIGNER 1808 Rev 9 05 INSTALLATION OF 1700 SERIES SIDEMOUNTED FOLDING DOOR HARDWARE SETS Measure door panels carefully and prepare finished opening accurately according to dimensions derived from2. formulas Header and side jambs must be square level and plumb for proper door operation and appearance SNUBBER Install in track with rubber end facing intended pivot jamb Slide to opposite end of track 2 DOOR SETS from pivot lock 4 door sets have two snubbers one facing each direction and located in center of track C E O E 4 DOOR EOE a a EEEE P P ART EEE D E EEE E ETE TRACK Fasten track 34 from front edge of LEVEL head jamb with pivot socket located on desired side Use 8 x 114 pan head screws A 34 x 34 wood fascia strip or quarter round may be placed at front edge of head jamb and track snugged against it HINGES Lay doors GOOD SIDE DOWN flat and even Fasten 1703 hinges as shown on drawing with hinge fingers separating doors and long leg of nylon block pointing toward intended pivot jamb edge Use 8 x 54 pan head screws TOP PIVOT Mount on back side of door 1 BOTTOM PIVOT Mount on back side of doors directly below top pivot TOP GUIDE Mount on back side of guide door 2 and or 3 1 2 from edge of door ALIGNERS USED ON 4 DOOR SETS ONLY Install on back side of doors 2 and 3 6 from bottom so that fingers mesh when doors are closed Use 8 x 54 pan head screws KNOB On flush doors drill 3X hole 36 from bottom and 11 2 from hinge edge of 2 and or 3 doors On louvered doors place to suit design Fasten knob to front
3. side of panel For 11 4 doors break off screw at groove EREAK OFF FOR 11 DOORS SPECIAL SCREW FURNISHED FOR 34 DOORS Y a ay 8 x 174 PAN HEAD SCREW DS A TRACK OPTIONAL ACCESSORIES 1775 1704 1714 DOOR KEEPER 34 FLOOR MOUNT 114 FLOOR MOUNT M BRACKET BRACKET Gf 2 we NON MORTISE LIFT OFF 1744 1754 HINGES 34 DOUBLE FLOOR 114 DOUBLE FLOOR MOUNT BRACKET MOUNT BRACKET f v HANG DOORS Fold door pairs together and turn nylon guide block at right angles to door as shown Tilt doors back at top and place guide block into track so that lip of block rests on ledge in track Swing doors to vertical position and slip top pivot pin into track pivot socket Make sure pivot socket tab is in unlocked position to allow inser tion of pin When pin is firmly seated slide lock tab over top of pin JAMB BRACKET Place a mark on jamb at bottom edge of doors Fold template as di rected below and position on jamb Use nail or punch to mark location of three holes for screws Fasten jamb bracket to jamb with 8 x 114 flat head screws Press down on bracket pivot socket and position bottom door pivot pin over socket Releasing socket locks onto pin ALIGN DOORS To maintain proper clear ances 14 at jamb X between doors it may be necessary to loosen and move track or jamb bracket pivot sockets Use wrench provided When doors are aligned and work ing smoothly lock door pi
4. vots in place with screws in holes of plates SNUBBER ADJUST SNUBBER Close doors and slide snubber until rubber touched nylon guide block Open doors and move snubber 1 nearer pivot jamb and tighten Doors should snap shut yet open easily by a slight pull DOOR on the knob Always open and shut doors Ve with knob MOVE SNUBBER Vg AND TIGHTEN f CUT OUT TX TEMPLATE FOR JAMB BRACKET LOCATION N NS ado a FOLD EDGE UP 90 MINIMUM CLEARANCE FROM FLOOR cuT 4 FOLD DOWN FOR RiG
Download Pdf Manuals
Related Search