JL Audio SB-T-4RNR2/10W3v2 User's Manual
Contents
1. tents back into cargo area For cosmetics we folded the corner of the carpet back under it self We do not recommend that you cut this carpet Supplied Hardware 2 3 8 Split Lock Washers 2 3 8 Flat Washers 2 3 8 x 1 1 4 Fender 2 3 8 16 x 2 1 4 hex 1 1 4 20 Install Bolt 3 8 16 x 2 1 4 Socket Cup Set Screw 1 3 x 3 Wax Square 2 3 8 16 Hex Nut Mid High Frequency Driver Information P TR690 TXI Front Location Driver Size 6x9 with separated tweeter Applicable JL Audio Products TR690 TXi amp VR690 CXi does require spacer mounting rings Rear Location Driver Size 6 3 4 Phone 954 443 1100 Applicable JL Audio Products TR650 CXi VR650 CXi amp XR650 CXi does require spacer mounting rings VR650 CXI Fax 954 443 1111 Page 3 Sheet SKU 011181 Revision 01 13 20042. Stealthbox INSTALLATION GUIDE for the SB T 4RNR2 10W3v2 02 Up Toyota 4 Runner SR 5 Sport Edition amp Limited _ a Holl STEP I Clean out all contents Remove the STEP 2 Remove the rear sill plate A and side STEP 3 Place the supplied wax square into cargo cover and carpet mat storage door B position With the sill plate removed pull and fold over the car The middle of wax square X marks the pet out of the corner circled spot needs to be 3 5 back from the wheel On Limited Edition interiors remove the plastic tray well and 2 5 from the side panel The flooring carpet will not fit flush aginst the Remove the adhesive protective paper from Stealthbox once isntalled the under side of the wax square and stick to the floor This Stealthbox is a product which requires professional installation skills and tools Please read this installation guide thor gt oughly before beginning the project It will guide you step by step through the installation Several of the steps in this process may require two people to accomplish It is absolutely vital that the enclosure be Rope mount d tothe tars STEP 4 Thread in the supplied tsocket cup set STEP 5 With the Stealthbox removed and wax STEP 6 Place and line up the hole of one of the according to these instructions Failure o mount the enclosure properly pres screw leaving about a 1 2 out of the Stealthbox square still in position u
3. eaded rod Use a 9 16 socket and long extension to fully secure the mounting assembly If the socket cup set screw is not protruding far enough loosen Specifications Enclosure Type Acoustical Suspension Sealed Driver Type OW3v2 D2 Nominal Impedance 42 Cont Power Handling 300Watts JL Audio recommends using a high quality amplifier such as the JL Audio 250 1 The diagram below shows the recommended crossover infrasonic filter and equalizer settings for the 250 1 when being used to power your Stealthbox 12VDC Ground Remote Preamp Output Section Bass Control Amp LP Fitter Output Mode Amplifier Input Section Subwoofer Output Oo 0 9 MONO OUTPUT ONLY Infrasonic Fiter Mode Slope FullRange Low Pass HighPass Off 30Hz Input Voltage Input Sens Signal Sensing off 1208 2408 Low High Off 0n 85 a 10 35 RI 1a as 20 as act 200 Left Ch Right Ch JL AUDIO 250 1 monoblock subwoofer amplifier LF Boost dB Filter Freq Hz Left Ch Right Ch The JL Audio 250 1 is a very versatile audio component Please consult the owner s manual for detailed information about installing and tuning this amplifier JL AUDIO hhead o fhe Curve www jlaudio com SB T 4RNR2 10Wv2 JL AUDIO Inc 2003 10369 N Commerce Pkwy Miramar Florida 33025 392 CONGRATULATIONS INSTALL COMPLETE STEP 13 Replace the carpet and any other con
4. se a 1 2 drill bit to drill out supplied black metal plates to the 1 2 drilled hole ents two problems 1 The sub bass Make sure that the socket cup end is exposed the marked location from STEP 5 performance will suffer due to the Place the Stealthbox into position and press down After hole is drilled remove the wax square Use tape to temporary secure the metal plate into movement of the enclosure caused by firmly position he force exerted by the woofer s and 2 A loose enclosure presents a serious safety hazard in the event of a collision or sudden deceleration Please enjoy your JL Audio Stealthbox responsibly JL AUDIO Ahead o fhe Curve STEP Continued on Next Page gt www jlaudio com SB T 4RNR2 10Wv2 JL AUDIO Inc 2003 Page 1 Sheet SKU 011181 Revision 01 13 2004 Cont From Previous Page 2S STEP 7 Place the carpet that was pulled out of the corner in STEP 2 back into position Cut out an access hole in the carpet that is lined up and position above the black metal plate s hole from STEP 6 Wr STEP 8 Remove the access door A and cargo net cleat B Follow STEPS 8A and 8B to properly remove the cargo net cleat STEP 8A This is how the cleat looks when installed into the side panel side panel not seen Grab a hold of the exposed knob s edge with your finger nails and pull out It should not require a lot of force Do not force it STEP 8B When the knob is
5. unlocked correctly the exposed knob will pull away from the side panel but is still attached to the cleat assembly With the cleat unlocked remove from the side panel JL AUDIO hkhead oL fhe Curve www jlaudio com STEP 9 Run the speaker wire to the Stealthbox s location Check for proper operation of the woofer and attach speaker wire to terminal Before placing the Stealthbox back into location back out the threaded rod to expose about SB T 4RNR2 10Wv2 JL AUDIO Inc 2003 Page 2 STEP 10 With the Stealthbox wired up and in location with socket cup set screw placed through the car pet metal plate and floor Place a supplied flat washer onto the supplied bolt Place the bolt assembly through the upper mounting support bracket of the Stealthbox and the factory plastic side panel On the back side of the plastic side panel place a supplied flat washer lock washer and then thread supplied nut onto the bolt assembly through the removed excess door loca tion Using a 9 16 open end wrench to hold the nut behind the plastic panel Tighten the exposed bolt with a 9 16 socket Continued on Next Page gt Sheet SKU 011181 Revision 01 13 2004 Cont From Previous Page STEP II Take the other supplied black metal plate lock washer flat washer and nut to the under side of vehicle STEP 12 Place the other black metal support plate flat washer lock washer and thread the nut onto the thr
Download Pdf Manuals
Related Search