Jettech Metal Products X-32 User's Manual
Contents
1. 2003 02 Welcome to JET TECH creating endless possibilities This manual was created specifically for you the end user We have included information to help troubleshoot problems and facilitate resolving those problems General information pertaining to our range of ware washers will be covered in this section Specific information on our current models are available upon request model by model If you find any discrepancy or can t find certain information please contact us We will be glad to be of assistance JET TECH SYSTEMS 5771 Ferrier street Montreal Quebec H4P 1N3 Tel 888 275 4538 888 ASK 4 JET 514 737 9701 Fax 514 342 3854 e mail service jet tech com Warranty MANUFACTURERS LIMITED WARRANTY Jet Tech Systems Corporation Jet Tech hereby warrants all new warewashers bearing the name JET TECH and installed within the continental United States of America or Canada to be free from defects in material and workmanship under normal and regular usage and operation for a period of one 1 year following the date of original installation unless specified otherwise but in no event can exceed eighteen 18 months from the date of shipment from the factory If a defect in material s or workmanship is detected or found to exist within the stated period above Jet Tech at its sole discretion shall either repair or replace any original equipment manufacturers part which has proven to fail within the2. machine providing that the equipment has not been altered or tampered with in any manner has been installed correctly as per the owners manual and maintained and operated in complete accordance with this manual The labor cost to repair or replace any part proven to be defective as per above clause s shall be covered by Jet Tech Systems within the continental United States of America or Canada provided that prior authorization for this labor was approved by Jet Tech Systems the service work was performed by an authorized Jet Tech service agency and that this agency installed an original and genuine Jet Tech part in the machine Any repair work performed by a non authorized service depot remains the sole responsibility of the user and Jet Tech Systems will not be held responsible The installation of any generic part will not be valid and therefore voids this warranty All authorized labor coverage shall be limited to regular hourly rates only Any supplemental hourly rates or charges such as weekends or emergency premiums remain the responsibility of the user Jet Tech Systems Corp Jet Tech hereby states that warranty travel time shall be limited to and without exception a round trip total of two 2 hours OR mileage up to a maximum of one hundred 100 miles round trip Any charges exceeding those stated herein must have prior authorization by the factory Exceptions to above warranty are A Damages resulting from shipping handling
3. of 6 grains or higher must have an on line water filtering system or some other type of water softening system Build up of calcium and lime deposits in the washer may occur and servicing will be required on a more frequent basis which will not be covered by the warranty ELECTRICAL Unit must be connected with a 110 volts 60Hz line The terminal block will receive L1 N and Ground wire Unit must be well grounded Breaker rating should be 15 amps Getting Sta Ted CREATION INNOVATION SELECTION Immediately upon receipt of your new X 32 dishwasher inspect the dishwasher for any obvious signs of damage If you do find any traces of damage contact the transport company that brought the dishwasher to your place at once A damage claim must be made immediately with the carrier Please assure that the following items are included with your X 32 dishwasher 1 20 x 20 open rack 1 20 x 20 peg rack for dishes 4 adjusting feet 1 operators manual Jef F 52S CREATION INNOVATION SELECTION Chemical hook up This unit is equipped with three 3 chemical pumps Each will inject a different liquid product at a specific time during the wash cycle The chemical pumps have sufficient length of tubing hose that can be inserted in gallon containers near the dishwasher The chemical pumps have colored tubing for ease of identification The colors are as follow Red for Detergent Clear for Sanitizer Blue for Rinse add
4. or abuse B Incorrect installation and or connections C Adjustments or calibration of any parts D Faults due to lack of regular maintenance or cleaning of any internal part s E Replacement of any wearable items such as glasswasher curtains or peristaltic squeeze tubing or gaskets F Excessive lime mineral alkali or hard water conditions In excess of 6 grain and G Poor results due to use of an incorrect type of detergent for non commercial type applications and excessive or inadequate water temperature s or pressure conditions or incorrect use H Labour and mileage coverage does not apply upon condition of sale JET TECH SYSTEMS CORPORATION STATES THAT THERE ARE NO OTHER WARRANTIES EXPRESSED OR IMPLIED THAT ARE NOT SET FORTH HEREIN JET TECH SYSTEMS CORPORATION SHALL ASSUME NO OTHER RESPONSIBILITY EITHER DIRECT OR NON DIRECT OR BE LIABLE FOR ANY OTHER OR ADDITIONAL LOSS OR DAMAGE WHETHER BEING DIRECT OR CONSEQUENTIAL AS A RESULT OF ITS EQUIPMENT Warranty One year parts amp labor Continental USA and Canada Exceptions Model F14 90 days labor amp One year parts The manufacturer reserves the rights to alter design and specifications without notice re AES a es t gt a to o o G ee DETERGENT SANITIZER lt gt F J y a a 4 Sanitary inner deep drawn wash tank Construction features OBody external housing wash tank and all chassis components in brushed
5. ached 60 of time 2 4 From 60 to 63 is the dripping time and in this phase only the timer still works 2 5 From 63 to 83 the solenoid valve ER and the rinse chemical pump MPB are operating MPB is delivering the right quantity of rinse aid product The quantity can be pre determined with the adjustment of the pump At the same time 63 to 83 the drain pump MPS is operating At this time the cycle has ended and the drain pump only is operating from 83 to 99 and automatically the dishwasher is ready to start again 3 The black SQUARE push button has a double function First function to give the possibility to make a pre wash or a continuous wash for as long as you want in pushing the black button the wash pump MPL works To stop the wash pump you must have the black push button in OFF position Second function is for de lime The operator must put the de liming chemical product in the water in the wash tank of X 32 and then push the black button When the de lime push button is in the ON position the wash pump MPL is working FOR NORMAL WASHING CYCLE THE PUSH BUTTON FOR DE LIME MUST BE IN THE OFF POSITION If during the wash cycle the de lime button is pushed in the wash cycle will stop and will only start again when the button is depressed this from the position reached at the moment that the de lime button has been pushed 4 The white SQUARE push button is for the total drain of the tank when the operator has finished
6. itive Ia emesene To prime the pumps you must complete two full wash cycles You can adjust the amount injected by turning the white screw on the chemical pump Installation Check List Is the dishwasher connected electrically Is the breaker turned on Is there water connected to the dishwasher Is the water valve opened Are the chemicals properly set starting the dishwasher the first time When starting the dishwasher for the first time you will notice that the only chemical that gets drawn in is the detergent The other chemicals will get drawn only during the wash cycle For more information go to Operation section De rati O nN CREATION INNOVATION 1 When you start the power GREEN PUSH BUTTON TL the machine automatically starts to fill the water until the correct water level is reached During the fill the solenoid valve EC and the detergent dosing pump MPD are operating 2 By pushing the BLACK ROUND push button TC the programmed washing cycle starts The length of the times are shown in the schematic electrical diagram 2 1 From 0 to 30 the machine is washing and only the wash pump is operating 2 2 From 30 to 50 while the wash pump is working also the sanitizer dosing pump MPSA is operating to fill the dishwasher with chemical sanitizer 2 3 From 50 to 60 the machine is washing and only the wash pump MPL is operating The wash pump stops to operate when the timer has re
7. stainless steel AISI 304 18 8 QO Reduced operating noise of 58 DbA due to utilization of double wall insulated panels OvUpper and lower wash and rinse jets on revolving arms constructed of fiberglass easy to remove and clean without the need for tools QO Safety micro switch on the door to interrupt wash pump action O Individual and adjustable variable speed peristaltic pumps for detergent sanitizer and rinse additive OPossibility of built in or free standing installation O Standard equipment includes insulated stainless steel top amp side panels QWash tank protected with double filters O Door opening with overall clearance of 14 25 in 86cm Q Automatic fill and water level regulation tank O Slide out front control panel provides easy access for service Overall dimensions height 33 5 in 85 cm Width 23 75 in 60 cm Depth 23 75 in 60 JET TECH SYSTEMS CORP TEL 514 737 9701 FAX 514 342 3854 1 888 275 4538 WWW JET TECH COM SALES JET TECH COM Jef tPF CLES CREATION INNOVATION e SELECTION Independent Chemical Pumps Technical Features cm ORack capacity 19 75 x 19 75 50 cm x 50 cm one open combination rack and on peg dish rack supplied OComplete cycle 160 seconds 145 second Wash amp 15 second Rinse Owash tank capacity 3 17 US gallon 12 liters OWash temperature 140F recommended Supply dependant no heaters OPower supply 110 volts 60Hz 7 Amps O Motor pump 0 75 H P Wi
8. th Clipson at 320F 160C Q Maximum Power rating 550 Watts OwWater consumption per cycle 1 5 U S Gallons 5 7 liters Oworking pressure 25 P S I Dynamic REAR 23 3 4 gt Bf oa oso gt no 6k UR SIDE k 93 3 4 JET TECHE DRAIN The X 32 is equipped with an automatic drain pump that will pump the drain water to a maximum height of 36 0 9 meter A 1 ID flexible drain hose is included to facilitate maintenance and servicing of the machine It is important not to reduce the size of this hose The drain should have a loop at the back of the dishwasher as per illustration below The loop should be 36 inches 36 above the floor and drop down into a drain pipe with an air gap These instructions must be followed for proper dishwasher operation It is normal for some water to remain in the wash tank after draining 36 high T Allow Air Gap WATER INLET A 3 4 NPT coupling is required with a maximum of 20 p s i dynamic pressure and a minimum of 18 p s i A water pressure regulator is required The water pressure should be 20 p s i Incoming water temperature must be 140 F 60 C An easily accessible shut off valve is recommended making installation service and repairs easier Flexible hoses must be used to make installation servicing and maintenance easier Make sure that the water is free from calcium and hard water deposits Water with a mineral contain
9. the washing operations ON Lal AN OFF 1 Drain Button 5 Thermometer gauge 2 Extended delime button 6 Wash cycle Start button 3 Power switch 7 Indicator light wash cycle 4 Indicator light power Jef tF SLES Electrical Schematics CREATION INNOVATION e SELECTION DPS Drain pump By pass switch MPS Drain Pump TL Main Power switch 3 a PS1 PS2 Pressure switches ER Rinse solenoid valve EC Fill solenoid valve MPD Detergent pump eo MPB Rinse additive pump MPSA Sanitizer pump e illie MP Door switch Ox TLS Deliming option switch CRP Contact from relay MT Timer motor l Mo M1 M2 M3 M4 M5 Timer contact z wir LC Light Timer cycle a 7 MPL Wash pump Mool o 5 i J oOo BR Relay coil D j aD o ae TC Start switch ST ok E CR Contactor relay swicth D LL Light Main power fe bg BRP Relay coil GH S z amp AZ 0 z IE ia a a eo Ss NS f k M Mie n Mm F LJ a
Download Pdf Manuals
Related Search