Jensen MP1311 User's Manual
Contents
1. MP1311 Disc Repeat RPT Press RPT 25 during disc play to continuously repeat the selected track S RPT will appear in the display Press RPT again to stop repeating S RPT will disappear from the display and regular play will resume The repeat function will also be canceled when activating the scan or shuffle functions Disc Shuffle RDM Press RDM 26 during disc play to play all tracks on a CD in random shuffled order S SHF will appear in the display Press RDM again to stop random play S SHF will disappear from the display and regular play will resume The shuffle function will also be canceled when activating the scan or repeat functions Disc Eject Press the eject button 29 to stop CD play and eject the disc The unit will change to tuner or AUX operation depending on which mode was in operation prior to disc play If the disc is not removed from the unit within 15 seconds the disc will be reloaded to prevent accidental damage Disc play can be resumed by pressing MODE 2 to choose the CD player function CD Player Error Codes If a problem should develop while operating the CD player an error code ER 1 ER 2 etc may appear on the display panel This can indicate a number of problems with the unit including a mechanical error or an error in the microprocessor control of the player If an error code should appear try ejecting and reloading th2. highest Select Press the AUDIO CONTROL button 4 to step through the menu of audio functions volume VOL bass BAS treble TRB balance BAL fader FAD and volume VOL When adjusting audio functions the unit will automatically exit select mode and return to the normal display after five seconds or when another function is activated Bass Press the AUDIO CONTROL button 4 twice until BAS appears in the display Within five seconds turn the AUDIO CONTROL 3 OS LINE clockwise or counter clockwise to adjust the bass from 10 to 10 00 represents a flat response The bass level is shown on the display for five seconds or until another function is activated Treble Press the AUDIO CONTROL button 4 three times until TRB appears in the display Within five seconds turn the AUDIO CONTROL 3 clockwise or counter clockwise to adjust Treble from 10 to 10 00 represents a flat response The treble level is shown on the display for five seconds or until another function is activated ea m femme D p P Kasa LINE Balance Press the AUDIO CONTROL button 4 four times until BAL appears in the display Within five seconds turn the AUDIO CONTROL 3 clockwise or counter clockwise to adjust Balance between the right and left speakers from BAL 10R full right to BAL 10L full left BAL L R represents an
3. only Do not attempt to use 3 8 cm CD singles in this unit either with or without an adaptor as damage to the player and or the disc may occur Such damage will not be covered by the warranty on this product Track Select Track select features are used to quickly access the beginning of a particular track when a disc is in play Press the Up Tuning button 14 to move forward or the Down Tuning button 13 to move backward on the disc to locate the desired track Track numbers will appear in the display as they are accessed Press and hold the Up or Down Tuning buttons to fast forward or fast reverse through a disc During either function the elapsed time will appear on the display Release the button to resume CD play Play Pause Press the play pause button 23 to suspend disc play S PAUSE will appear in the display and the center of the disc icon 7 will stop rotating Press the play pause button again to resume disc play The S PAUSE indication will disappear from the display and play will resume from the pausing point MP1311 Disc Scan SCN During disc play press SCN 24 to play the first 10 seconds of each track on the disc S SCN will appear in the display When the desired track is reached press SCN again to end the scan function and play the selected track S SCN will disappear from the display The scan function will also be canceled when activating the repeat or shuffle functions
4. stop scanning and listen to the current station Mono Stereo Selector MONO Press MONO 18 during FM radio operation to select stereo reception of the broadcast signal Under normal reception the unit should be left in the stereo mode as indicated by the ST designation and the associated signal strength indicator that appear on the display panel when tuned to an FM stereo signal If the signal is too noisy for comfortable listening press MONO to switch to mono reception The ST indication will disappear Press MONO again to return to stereo mode Local Distance Selector This feature is used to designate the strength of the signals at which the radio will stop during automatic tuning Distant or Dx is the default setting allowing the radio to stop at a broader range of signals To set the unit to select only strong local stations during automatic tuning press the LOC button on the remote control LOCAL appears in the display 11 Kasa LINE CD PLAYER OPERATION Insert CD With the label surface facing up gently insert the disc into the CD slot 21 until the soft loading mechanism engages and pulls the disc in Disc play begins CDP PLAY will appear in the display and the CD icon will become animated The center of the disc icon 7 iluminates and becomes animated and the track number and elapsed time appear in the display NOTE The unit is designed for play of standard 5 12 cm compact discs
5. the AS PS button 17 four times to enter Current Directory Search mode The LCD will display the current directory name followed by the file currently play ing Turn the AUDIO CONTROL 3 to browse all available folders or files in the current directory Press the AUDIO CONTROL button to select a folder or file If a folder is selected a folder with an F appears on the LCD indicating that the selection is a folder Repeat 17 Im LINE AR steps 2 and 3 to select a file for playback If a file is selected playback begins automatically Select the folder icon to return to the previous file level and select a different directory or file Display Information Press the D button 9 to display the clock or available ID3 information as follows song title directory name artist name etc LINI REMOTE CONTROL The remote control will allow you to control the basic functions of the MP1311 The remote control sensor is located on the left side of the front panel to the right of the MONO button 18 PHASE MP1311 AMS AS PS PEQ EQ MOD MODE LOC Local Distant BND BAND SCN Scan AM FM MUT Ja MO MONO DISP Clock Frequency MP1311 CARE AND MAINTENANCE CD Player Compact Discs The following guidelines will help you extend the life of your CD player 1 2 When cleaning the vehicle interior do not get wate
6. D3 Tag This unit supports ID3 tag versions 1 0 and 1 1 For the character codes refer to the table below 3 4 5 6 7 8 9 A BICIDJEJF 0 Oe P p m ADjajd 1 I 1 AlQlalaq iI 1AlNnlan 2 2 B Rib r 2 l l l 3 3 C S e s Al OA 6 4 4 D Tl d t O AlO6a6 5 5 EJUjeju HIA O a 6 6 6 FIVi flv IE Ole 6 7 7 G W 9 w S C X C 8 8 H X h x DITIEI Q Aa g 9 9 I Y lily U A iiz hi z 2 E SIKU kit I E U amp a C lt L VIL ajWa 1101 i a D M m ll 2 Y V E gt N A n OS j P ilb F O _ o E i IIB II Y Entering File and Folder Names Names using the code list characters are the only file names and folder names that can be entered and displayed Other characters will not display correctly The unit recognizes and plays only files with the MP3 WMA extension NOTE A file name entered with characters not on the code list may not play correctly Writing Files into a Disc When a disc containing MP3 WMA data is loaded the unit checks all data If the disc contains many folders or non MP3 WMA files MP3 WMA play will be delayed it may take time for the unit to move to the next file and searches may not be performed smoothly Loading such a disc may produce loud noise and cause damage to the speakers Do not attem
7. MP1311 Owner s Manual UN AM FM CD MP3 WMA Receiver MP1311 MP3 WMA RECEIVER l f LINEAR M ONO COMPACT DIGITAL AUDIO CD R RW OBR LINE PREPARATION Getting Started Congratulations on your purchase of the Phase Linear MP1311 Mobile AM FM CD MP3 WMA Receiver It s a good idea to read all of the instructions before beginning the installation We recommend having your Phase Linear MP1311 installed by a reputable installation shop Contents Installation Instructions 3 dij i e em na a 6 Operating Instructions 7 Tuner Operation 10 CD Player Operation 12 MP3 WMA Operation 14 Remote Control 18 Care and Maintenance 19 Troubleshooting 20 Specifications 21 Installation Reguirements This unit is designed for installation in cars trucks and vans with an existing radio opening In many cases a special installation kit will be reguired to mount the radio to the dashboard These kits are available at electronics supply stores and car stereo specialty shops Always check the kit application before purchasing to make sure the kit works with your vehicle If you ne
8. NTER button 5 or AUDIO CONTROL button 4 to begin playback Directory File Search 1 Press the AS PS button 17 twice to enter Directory or File Name Search mode The LCD will display a blinking asterisk Use the keys specified in Table 1 or turn the AUDIO CONTROL 3 to enter a search string Pressing the appropriate key repeatedly will scroll through the corresponding number and characters Press the AUDIO CONTROL button 4 to confirm each character Press the BAND ENTER button 5 to begin the search If the search results in a directory name a folder with an F will appear on the display 1 In this case use the Up Tuning 14 or Down Tuning 13 buttons to select a song folder in the directory Press the BAND ENTER button 5 to confirm and begin playback Repeat if the search results in another directory Root Directory Search 4 Press the AS PS button 17 three times to enter Root Directory Search mode The LCD will display the first folder or file name in the root directory Turn the AUDIO CONTROL 3 to browse all available folder or files in the root directory Press the AUDIO CONTROL button 4 to select a folder or file If a folder is selected a folder with an F appears on the LCD indicating that the selection is a folder Repeat steps 2 and 3 to select a file for playback If a file is selected playback begins automatically Current Directory Search 1 Press
9. ONTROL 4 Turn the AUDIO CONTROL to select from the following Beep Tone options BEEP ALL Beep is heard any time a button is pressed function activated BEEP 2ND Beep is heard only when a secondary function is activated press and hold BEEP OFF Beep is not heard 8 MP1311 Equalizer Selector EQ The equalizer function applies preset sound effects to the unit s audio output signal Press EQ 20 to activate one of the following operating modes FLAT CLASSICS POP M ROCK M or DSP OFF When the equalizer function is activated the most recently selected bass treble levels are ignored If the bass and or treble levels are adjusted while the equalizer function is active the equalizer function will revert to FLAT When the equalizer function is not active the unit will return to the most recently selected bass and treble levels Liquid Crystal Display LCD The liquid crystal display LCD panel 8 displays the frequency time and activated functions of the unit including an audio level indicator which appears as a bar graph depicting the audio signal In addition the display contains a receive signal indicator that depicts the relative strength of the incoming broadcast frequency NOTE After being subjected to cold temperatures LCD panels may take longer to respond and visibility of the numbers on the LCD may decrease slightly The LCD display will return to normal when the temperature increas
10. ch must be on If the unit does not operate recheck all wiring until the problem is corrected Once proper operation is achieved turn the ignition switch off and proceed with final mounting of the chassis Carefully slide the radio into the mounting sleeve making sure it is right side up until it is fully seated and the spring clips lock it into place Kasa LINE o Attach one end of the perforated support strap supplied to the screw stud on the rear of the chassis using the hex nut provided Fasten the other end of the perforated strap to a secure part of the dashboard either above or below the radio using the screw and hex nut provided Bend the strap as necessary to position it CAUTION The rear of the radio must be supported with the strap to prevent damage to the dashboard from the weight of the radio or improper operation due to vibration 10 Re attach the front panel to the chassis and test radio operation by referring to the operating instructions for the unit NOTE For proper operation of the CD player the chassis must be mounted within 20 of horizontal Make sure the unit is mounted within this limitation Kit Installation If your vehicle requires the use of an installation kit to mount this radio follow the instructions included with the installation kit to attach the radio to the mounting plate supplied with the kit 1 Wire and test the radio as outlined in the Universal Installation instru
11. ctions 2 Install the radio mounting plate assembly to the sub dashboard according to the instructions in the installation kit 3 Attach the support strap to the radio and dashboard as described in the Universal Installation instructions 4 Replace the dashboard trim panel ISO Installation This unit has threaded holes in the chassis side panels which may be used with the original factory mounting brackets of some vehicles to mount the radio to the dashboard Please consult with your local car stereo shop for assistance on this type of installation 1 Remove the existing factory radio from the dashboard or center console mounting Save all hardware and brackets as they will be used to mount the new radio 2 Carefully unsnap the plastic frame from the front of the new radio chassis Remove and discard the frame 3 Remove the factory mounting brackets and hardware from the existing radio and attach them to the new radio Do not exceed M5 x 9 MM maximum screw size MP1311 Longer screws may damage components inside the chassis 4 Wire the new radio to the vehicle as outlined in the Universal Installation instructions 5 Mount the new radio assembly to the dashboard or center console using the reverse procedure of step 1 Reconnect Battery When wiring is complete reconnect the battery negative terminal MP1311 Remove Radio To remove the radio after installation remove the trim ring by lifting in
12. does not support WAV OGG or other formats CD Care and Handling Dirt dust scratches and warpage can cause skips in the playback and deterioration of sound quality Please follow these guidelines to take care of your compact discs Carefully wipe fingerprints dust and dirt from the disc s playing surface with a soft cloth Wipe in a straight motion from the inside to the outside of the disc 2 Never use chemicals such as record sprays or household cleaners to clean 19 CDs as they can irreparably damage the disc s surface Discs should be kept in their storage cases when not in use Do not expose discs to direct sunlight high temperatures or high humidity for long periods Do not stick paper tape or CD labels on disc surfaces as internal damage may occur RASS MP1311 TROUBLESHOOTING Does not operate display does not No power to yellow wire no power to red wire Check connection with test light check vehicle fuse with test light light Inline fuse blown Replace fuse No power to unit Inline fuse blown Check replace fuse Not all speakers operate Incorrect splices or connections Check all splices and connections Speaker wires shorting to chassis ground or to Check splices insulate all bare wires each other Blows fuses Power wire shorting to ground Make sure wire is not pinched Speaker wires shorting to ground Make sure wire is not pinched O Incorrect fuse or fuse too small fuse or fuse t
13. e attaching the Front Panel To re attach the front panel make sure the electrical terminals on the back of the panel are free of dust and dirt as debris could cause intermittent operation or other malfunctions Position the right side of the panel in place so 9 I LINE AR that it is correctly engaged then lightly press the left side of the panel until the mechanism locks it into place Reset Button The reset button 11 is located on the front of the chassis and can only be accessed with the front panel removed The reset circuitry protects the microprocessor circuitry Since resetting the unit will erase the time and preset memories it should only be activated upon initial installation after all wiring is complete or if there is a malfunction of any of the switches on the unit In these circumstances pressing the reset button will clear the system and return the unit to normal operation i i I J Theft Deterrent LED A light emitting diode LED 12 is located on the chassis behind the front panel and will flash when the panel is removed The flashing light serves as a visual warning to the would be thief that the unit has been disabled by removal of the front panel Kosa LINE TUNER OPERATION AM FM Band Selector BAND Press BAND 5 during radio play to switch between three FM bands and one AM band F1 F2 F3 or AM will appear in the display to indicate the band current
14. e control To store a station turn the radio on and select the desired band and station Press and hold the desired preset button numbered one through six on the face of the radio or remote control for more than two seconds When stored the preset number will appear in the display The station is now stored and can be recalled at any time by pressing the corresponding preset button MP1311 Repeat for the remaining five presets on the current band and for all presets on the other three bands Automatically Store Preset Scan AS PS Automatically Store Select six strong stations and store them in the current band using the Automatic Store feature To enable this feature press and hold AS PS 17 for more than two seconds The radio will automatically scan the band in use and enter strong stations into the preset memory positions for that band After entering the stations into memory the unit will automatically stop at each station for five seconds so each can be heard When using the Automatically Store feature the new stations replace any stations already stored in preset memory for the selected band Preset Scan Press AS PS 17 to scan the six preset stations in the AM band or all FM bands The unit will stop at each station for five seconds before continuing to the next preset station and the preset number will flash on the display during the preset scan Press AS PS again to
15. e disc into the player While the disc is out of the unit make sure it is clean and undamaged and then load it correctly If this does not solve the problem pressing the reset button 11 may help but will erase the time and preset memory If the suggested measures do not solve the problem contact an approved warranty station near you for further assistance 13 Kosa LINE MP3 WMA OPERATION MP3 and WMA Windows Media Audio music files are digital audio files that are compressed to allow more files on a single CD This unit can play MP3 WMA directly from files contained on a CD R RW using the buttons on the receiver or optional remote as described below Many types of software are available for converting audio files into MP3 WMA formats Phase Linear recommends Nero or Roxio Easy CD Creator Depending on the media type and recording method some CD R RWs may be incompatible with this unit The unit supports playback of MP3 WMA and CDDA CDA Mixed Mode CDs and CD Extra including multi session discs but discs on which the session has not been closed will not play Notes on MP3 WMA Play This unit can play MP3 MPEG1 2 2 5 Audio Layer 3 However the MP3 recording media and accepted formats are limited When writing MP3 WMA pay attention to the following restrictions Acceptable Media The MP3 WMA recording media acceptable to this unit are CD ROM CD R and CD RW When using CD RW use full format rather than g
16. ed a kit but cannot locate one call our customer support line at 1 800 323 4815 U S A and Canada only Tools and Supplies The following tools and supplies are needed to install the radio Torx type flathead and Philips screwdrivers e Wire cutters and strippers Tools to remove existing radio screwdriver socket wrench set or other tools e Electrical tape Crimping tool Volt meter test light Crimp connections 18 gauge wire for power connections 16 18 gauge speaker wire Speaker Requirements Only connect speakers rated with a load impedance of 4 ohms Speakers with a load impedance of less than 4 ohms could damage the unit MP1311 Disconnect Battery Before you begin disconnect the battery negative terminal Toll Free Installation Assistance If you require assistance contact Technical Support at 1 800 323 4815 from 8 30 a m to 7 00 p m EST Monday through Friday and from 9 00 a m to 5 00 p m EST on Saturday U S A and Canada only MP1311 INSTALLATION INSTRUCTIONS Universal Installation Using This unit is designed for installation in cars trucks and vans with an existing radio opening In many cases a special installation kit will be reguired to mount the radio to the dashboard These kits are available at electronics supply stores and car stereo specialty shops Always check the kit application before purchasing to make sure the kit works with your vehicle Pre i
17. equal balance level between the right and left speakers The balance position is shown on the display for five seconds or until another function is activated Fader Press the AUDIO CONTROL 4 five times until FAD appears in the display Within five seconds turn the AUDIO CONTROL 3 clockwise or counter clockwise to adjust balance between the front and rear speakers from FAD 10R full rear to FAD 10F full front FAD F lt R represents an equal balance level between the front and rear speakers The fader position is shown on the display for five seconds or until another function is activated VOL FAD BAS X BASS BAND Press and hold the BAND button 5 for two seconds to activate the X BASS feature When listening to music at low volume levels this feature will boost the bass and treble ranges to compensate for the characteristics of human hearing When activated X BAS appears on the display Press BAND again for two seconds to deactivate this feature Audio Mute MUTE Press ja 6 to mute the audio volume MUTE flashes on the display Restore volume to the previous setting by pressing the mute button again adjusting the AUDIO CONTROL or by pressing any other button on the unit Beep Tone The beep tone feature allows the selection of an audible beep tone to be heard each time a button is pressed on the face of the radio To access the Beep Tone menu press and hold the AUDIO C
18. es to a normal range MP1311 Display D When the unit is off the LCD displays the time of day When the unit is on the LCD automatically shows the tuner or CD display depending on which mode of operation is currently activated Display Clock During tuner or CD operation press D 9 to display the time of day After five seconds the display reverts to tuner or CD display Set Clock 1 To set the clock turn the radio on in tuner mode or any other mode 2 Press D The time appears on the display 3 Press and hold D until the time display begins flashing 4 While the display is flashing press the Up Tuning button 14 to adjust hours and the A AM or P PM indication Press the Down Tuning button 13 to adjust minutes 5 After five seconds the time will set and the display will return to tuner or CD display Auxiliary Input Use the Aux In connector 19 to connect a portable media device for playback through the vehicle sound system Front Panel Release The front panel release button 10 releases the mechanism that holds the front panel to the chassis Detaching the Front Panel To detach the front panel first press the front panel release button 10 to release the left side of the panel Next grasp the released side and pull it off the chassis After removing the front panel store it in the supplied carrying case to protect it from dirt and damage REMOVE FRONT PANEL R
19. ics Corporation the Company is committed to guality and customer service and are pleased to offer you this Warranty Please read it thoroughly and contact the Company at 1 800 323 4815 with any guestions Who is covered The Company extends this warranty to the original retail purchaser of products purchased through an authorized Audiovox retailer in the U S A Puerto Rico or Canada This warranty is not transferable or assignable Proof of purchase is required in the form of an original sales receipt What is covered The Company warrants that should this product or any part thereof under normal use be proven defective in material or workmanship within 90 days from the date of original purchase such defect s will be repaired or replaced with a new or reconditioned product at the Company s option without charge for parts and repair labor What is not covered This Warranty does not cover the following Damage incurred during shipping or transporting the product to the Company or a service center Elimination of car static or motor noise Defects in cosmetic decorative or non operative structural parts Correction of antenna problems Costs incurred for installation removal or reinstallation of the product Consequential damage to compact discs USB devices digital media cards accessories or vehicle electrical systems Damage caused by improper installation mishandling misuse neglect accident blown fuse bat
20. ly selected Tuning Automatic Tuning Press the Up Tuning 14 button to tune upward in freguency and the Down Tuning 13 button to tune downward in freguency The unit will automatically stop at the next strong station If the Local mode is active the radio will seek the next strong local station when either button is pressed Manual Tuning Press the Up Tuning 14 or Down Tuning 13 button for more than two seconds to select manual tuning mode MANUAL will appear in the display Press the Up or Down Tuning buttons to move radio freguency up or down two digits at a time Press and hold the Up or Down Tuning buttons to guickly advance to a certain freguency Release when the desired frequency is reached If tuning is not adjusted within five seconds of entering manual tuning mode the radio will revert to automatic tuning and AUTO will appear in the display Scan Tuning SCAN Press SCAN 15 to scan upwards through all the strong channels in the current band The unit will pause and play each station for five seconds and the station frequency will flash in the display during this time Press SCAN again to stop scanning and listen to the current station NOTE The Scan function does not work correctly in MANUAL mode MP1311 Preset Stations Up to six stations on each band can be stored as presets and can then be instantly recalled by pressing the associated preset button on the front panel 16 or remot
21. nstallation 1 Disconnect Battery Before you begin always disconnect the battery negative terminal Remove Transport Screws Mounting Sleeve 1 Remove the detachable front panel if it is attached to the chassis by pushing the Release button Slide the mounting sleeve off of the chassis if it has not already been removed If it is locked into position use the removal keys supplied to disengage it The removal keys are depicted on page 5 Check the dashboard opening size by sliding the mounting sleeve into it If the opening is not large enough carefully cut or file as necessary until the sleeve easily slides into the opening Do not force the sleeve into the opening or cause it to bend or bow Check that there will be sufficient space behind the dashboard for the radio chassis Locate the series of bend tabs along the top bottom and sides of the mounting sleeve With the sleeve fully inserted into the dashboard opening bend as many of the tabs outward as necessary to firmly secure the sleeve to the dashboard Place the radio in front of the dashboard opening so the wiring can be brought through the mounting sleeve Follow the wiring diagram carefully and make certain all connections are secure and insulated with crimp connectors or electrical tape to ensure proper operation After completing the wiring connections attach the front panel and turn the unit on to confirm operation vehicle ignition swit
22. oo small Install fuse of correct Install fuse of correct rating CD skips too much Receiver mount is not solid or mm fa is not Check mounting and ee tighten if needed secure 20 MP1311 SPECIFICATIONS CEA Power Ratings Power output 13 watts RMS X 4 channels into 4 ohms lt 1 THD N Signal to noise ratio 7OdBA below reference Reference 1 watt 4 ohms Freguency response 20Hz to 20kHz 3dB Auxiliary input used as source reference Reference supply voltage 14 4VDC CD Player Signal to noise ratio gt 9OdBA Frequency response 20Hz 20kHz 3dB Channel separation gt 55dB 1kHz D A converter 1 Bit CH FM Tuner Tuning range 87 5MHz 107 9MHz Mono sensitivity 12dBf 50dB quieting sensitivity stereo 16dBf Stereo separation 1kHz gt 35dB Frequency response 30Hz 14kHz 3dB AM Tuner Tuning range 530kHz 1710kHz Sensitivity 20dB signal to noise 30uV Frequency response 50Hz 2kHz 3dB Auxiliary Input Input sensitivity 400mV RMS for 1 watt RMS into 4 ohms Freguency response 20Hz to 20kHz 3dB Input impedance 10 k ohms General Power supply 11 16 VDC negative ground Power Antenna Blue 500mAmp Max current limited protection Operating Temp 10C 60C Fuses 15 amp fast blow ATO DIN chassis dimensions 2 H x 7 W x 7 D 51mm x 178mm x 178mm Specifications subject to change without notice 21 Limited Warranty CD or Multimedia Radios Headunits Audiovox Electron
23. pt to play a disc containing a non MP3 WMA file with the MP3 WMA extension or a disc containing non MP3 WMA files Electronic Shock Protection 10 seconds for CDDA CDA 100 seconds for MP3 WMA recorded at 44 1kHz 128kbps Bit Rates The unit supports bit rates from 32 320 kbps File Playing Order When selected for play files and folders Folder Search File Search or Folder Select are accessed in the order they were written by the CD writer As a result the order in which they are expected to be played may not match the order in which they are actually played ANRI EF nri CL ANT sla LINE AR You may be able to set the order in which MPS WMA are to be played by writing them onto a disc such as a CD R with their file names beginning with play seguence numbers such as 01 to 99 For example a disc with the following folder file hierarchy is subject to Folder Search File Search or Folder Select as shown below G do Ld DO e do 2 5 do dB FT Folder la D 9 Q File AO Root Level 1 Level 3 Level 2 Level 4 Pause Press the 1 gt button 23 to suspend disc play Press the play pause button again to resume play Track Select Press the Up Tuning 14 or Down Tuning 13 button for less than one second to advance to the next track on the disc or press and hold to fast forward or fast reverse th
24. r or cleaning fluids on the unit The CD player will not operate properly in extreme hot cold or under damp conditions In case of such conditions wait until the vehicle interior reaches a normal temperature or any condensation on the disc player lens has evaporated before using the player Never insert anything other than round 5 CDs into the player Attempting to insert CDs of other sizes even with an adaptor will cause damage not covered by the warranty Always remove the CD when the player is not is use The unit is designed with a vibration dampening CD mechanism to minimize interruption of disc play due to normal vibration in a moving vehicle However occasional sound skips may occur when driving on very rough roads This will not scratch or damage the disc and normal play will resume when the rough conditions cease CD R and CD RW Capability Depending on media type and method of recording burning some CD R RWs may be incompatible with this unit After recording burning the session must be closed Please refer to your software s recommended procedures for closing a disc session Review your recording software to familiarize yourself with the correct recording burning procedures We recommend using the latest versions of ROXIO or NERO burning software In addition this unit will only recognize the CDDA Compact Disc Digital Audio MP3 and WMA formats recorded burned onto a CD R RW This unit
25. rough the disc Disc play starts when the button is released Navigating Folders Press the DN V and UP A buttons 27 28 to select the next or previous folder directory Intro Scan SCN During disc play press SCN 24 to play the first 10 seconds of each track on the disc When the desired track is reached press SCN again to end the scan and play the selected track Repeat RPT Press the RPT button 25 to repeatedly play the current file Press RPT again to resume normal playback Random RDM Press the RDM button 26 to randomly play all files on the disc Press RDM again to resume normal playback 16 MP1311 MP3 WMA File or Folder Search The unit offers four methods of searching for files or folders on a disc Direct File Number Search Press the AS PS button 17 to enter Direct Track Search mode The LCD will display MP3 T followed by a blinking asterisk Refer to the Number column in Table 1 to enter a track number to play Table 1 Search Characters Key Number Characters 5 TUNE gt gt 9 Y Z blank om o lt If you enter a three digit track number the unit will search the track immediately If you enter one or two digits press the BAND ENTER MP1311 button 5 to begin the search or wait a few seconds for the search to begin automatically You can also turn the rotary to access and file numbers seguentially After locating the desired file press the BAND E
26. rranty lasts or the exclusion or limitation of incidental or consequential damage so the above limitations or exclusions may not apply to you This Warranty gives you specific legal rights and you may also have other rights which vary from state to state Obtaining Warranty Service e To obtain repair or replacement within the terms of this Warranty call 1 800 323 4815 for the location of a warranty station serving your area e You must prepay the initial shipping charges to the Company The Company will pay the return shipping charges for all warranteed products returned to an address within the U S A Puerto Rico or Canada e Please package the product securely to avoid shipping damage We recommend using a carrier that provides tracking service to prevent lost packages Lost or damaged packages are not covered by this warranty e Provide a detailed description of the problem s for which you require service Audiovox Electronics Corporation 150 Marcus Boulevard Hauppauge NY 11788 1 800 323 4815 www audiovox com L 2007 Audiovox v 083107
27. s O to chassis ground Failure to wire When replacing a fuse make sure the new fuse is the correct type and amperage Using an incorrect fuse could damage the radio The MP1311 uses one 15 amp fuse located below the wiring connector 15 amp fast blow ATO Gray exactly as shown may cause electrical damage to the radio MP1311 OPERATING INSTRUCTIONS Power Press the power button 1 or any other button on the face of the receiver to turn the unit on when the ignition switch is on Press the power button again to turn the receiver off If the radio was left on when the ignition was last turned off the receiver will turn on automatically when the ignition switch is again turned on If the receiver was off when the ignition was last turned off the receiver must be turned on manually when restarting the vehicle Mode Press MODE 2 to select a different mode of operation as indicated on the display panel Available modes include Tuner CD and Auxiliary Input During CD player operation pressing MODE will change to the tuner mode without ejecting the disc To access the Auxiliary Input mode press the MODE button until AUX is indicated in the display Volume To increase the volume turn the AUDIO CONTROL 3 clockwise To decrease the volume rotate the AUDIO CONTROL counter clockwise When volume is adjusted the volume level is shown on the display panel asa number ranging from 00 lowest to 100
28. tery leakage theft or improper storage Products whose factory serial number bar code label s or markings have been removed or defaced Damage resulting from moisture humidity excessive temperature extreme environmental conditions or external natural causes Please review the Care and Maintenance section of your Installation and Operation Manual for additional information regarding the proper use of your product DO NOT RETURN THIS PRODUCT TO THE STORE Limitations THE EXTENT OF THE COMPANY S LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT PROVIDED ABOVE AND IN NO EVENT SHALL THE COMPANY S LIABILITY EXCEED THE PURCHASE PRICE PAID BY PURCHASER FOR THE PRODUCT This Warranty is in lieu of all other express warranties or liabilities ANY IMPLIED WARRANTIES INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY SHALL BE LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY ANY ACTION FOR BREACH OF ANY WARRANTY HEREUNDER INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY MUST BE BROUGHT WITHIN A PERIOD OF 24 MONTHS FROM DATE OF ORIGINAL PURCHASE IN NO CASE SHALL THE COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY EXPRESS OR IMPLIED WHATSOEVER No person or representative is authorized to assume for the Company any liability other than expressed herein in connection with the sale of this product Some states do not allow limitations on how long an implied wa
29. the center and pulling it off from either side Insert the removal keys straight back until they lock and then pull the radio out If removal keys are inserted at an angle they will not lock properly to release the unit Removal Key Kosa LINE WIRING 1 Power Antenna dark blue wire Connect MP1311 to power antenna or amplifier If not used tape bare end of wire Accessory Ignition red wire Connect to existing radio wire or radio fuse Ground black wire Connect to ground terminal or clean unpainted part of chassis Memory Battery yellow wire Connect to battery or 12 volt power source that is always live The radio will not work if this wire is not connected Antenna Connector Connect the antenna plug from the existing antenna cable some vehicles reguire an adaptor Outputs to Amplifier gray RCA cables Connect line out for optional external amplifiers The red connector is for the right and the white connector is for the left Left Front Speaker Right Front Speaker Left Rear Speaker Right Rear Speaker Fuses is Dark Blue Gde Bo Black Ot 85 J me n Red NOTE The amplifiers in this radio are Pa only designed for use with four speakers Never combine bridge WAAR li outputs for use with two speakers Gray Black Never ground negative speaker lead
30. uick format to prevent malfunction Acceptable Disc Formats The following formats are available for the media used in this unit The maximum number of characters used for file name including the delimiter and three character extension are indicated in parentheses ISO 9660 Level 1 11 characters ISO 9660 Level 2 31 characters JOliet 31 characters Romeo 31 characters Up to 200 characters can be displayed in the long file name format For a list of available characters see the instruction manual of the writing software and the section Entering File and Folder Names below The media reproducible on this unit has the following limitations Maximum number of nested folders 8 Maximum number of files per disc 999 Maximum number of folders per disc 255 MP3 WMA written in formats other than those listed above will not play successfully and their file names or folder names will not be displayed properly 14 MP1311 MP3 WMA Encoder and CD Writer Settings Use the following settings when compressing audio data in MP3 data with the MP3 encoder Transfer bit rate 32 320 kbps Sampling frequency 32 44 1 48kHz WMA and 16 22 05 24 32 44 1 48kHz MP3 When using a CD writer to record MP3 WMA up to the maximum disc capacity disable additional writing To record an empty disc up to the maximum capacity at once select the disc at once option MP1311 Entering I
Download Pdf Manuals
Related Search