Jensen Marine Direct MCD5060 User's Manual
Contents
1. Screw Stud 10 uu Follow the wiring diagram carefully and make certain all connections are secure and insulated with crimp connectors or electrical tape to ensure proper operation After completing the wiring connections attach the front panel and turn the unit on to confirm operation vehicle ignition switch must be on If the unit does not operate recheck all wiring until the problem is corrected Once proper operation is achieved turn the ignition switch off and proceed with final mounting of the chassis Carefully slide the radio into the mounting sleeve making sure it is right side up until it is fully seated and the spring clips lock it into place Attach one end of the perforated support strap Dashboard supplied to the screw stud on Support Strap the rear of the chassis using com the hex nut and spring washer Plain Washer qe provided Fasten the other end of the perforated strap to a Screw 5 x 25mm secure part of the dashboard Fe Screw Stud either above or below the radio Nut 5mm NK using the screw and plain Spring Washer washer provided Bend the L strap as necessary to position it CAUTION The rear of the radio must be supported with the strap to prevent damage to the dashboard from the weight of the radio or improper operation due to vibration Re attach the front panel to the chassis and test radio operation by referring to the operating instructions for the un2. Memory Battery Connect to battery or 12 volt power source that is always live The radio will not work if this wire is not connected Accessory Ignition Connect to existing radio wire or radio fuse Figure 1 20 PIN HARNESS PIN CHART 112113 14 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 PIN WIRE COLOR FUNCTION LABEL 1__ GREY BLACK RIGHT FRONT SPEAKER 2 GREY RIGHT FRONT SPEAKER 3 VIOLET RIGHT REAR SPEAKER 4 VIOLET BLACK RIGHT REAR SPEAKER 5 EMPTY N A 6 GREEN LEFT REAR SPEAKER 7 GREEN BLACK LEFT REAR SPEAKER 8 RED IGNITION ACC 9 BLACK REAR PRE AMPLIFIER LINE OUT COMMON 10 RED RIGHT REAR PRE AMPLIFIER LINE OUT 11 WHITE LEFT FRONT SPEAKER 12 WHITE BLACK LEFT FRONT SPEAKER 13 EMPTY N A 14 BLUE POWER ANTENNA 15 YELLOW BATTERY 16 BLACK CHASSIS GROUND 17 EMPTY N A 18 EMPTY N A 19 EMPTY N A 20 WHITE LEFT REAR PRE AMPLIFIER LINE OUT MCD5060 ap BASIC OPERATION Cla D HIT Gar 1 ia 7 us ay J Control Panel Release RE
3. Temperature inside the vehicle is too high Clean the disc or try to play a new one Wait until the ambient tempera ture returns to normal Condensation Leave the player off for an hour or so then try again No sound Volume is too low Adjust volume to audible level Wiring is not properly con nected Check wiring connections The operation keys do not work Control panel not properly installed Reinstall control panel The built in microcomputer is not operating properly due to noise Press the RESET button Sound skips The installation angle is more than 30 degrees Adjust the installation angle to less than 30 degrees The disc is dirty or defec tive Clean the disc and try to play again or use new disc Cannot tune to radio sta tion auto seek does not work The antenna cable is not connected Insert the antenna cable firmly The signals are too weak Select a station manually ERROR 1 Mechanism Error Press the eject button to correct the problem If the error code does not disap pear consult your nearest ser vice dealer ERROR 2 Servo Error Press the eject button to correct the problem If the error code does not disap pear consult your nearest ser vice dealer MCD5060 The Mobile Electronics Company Aubpiovox SPECIALIZED APPLICATIONS LLC ASA Electronics Corporation www asaelectronics
4. MCD5060 MARINE CD PLAYER RECEIVER Installation and Operation Manual MCD5060 uu SAFETY INFORMATION When Driving Keep the volume level low enough to be aware of the road and traffic conditions Protect from Water Do not expose the product directly to water as this can cause electrical shorts fire or other damage Protect from High Temperatures Exposure to direct sunlight for an extended period of time can produce very high temperatures inside your vehicle Give the interior a chance to cool down before starting playback Do not mount radio within close proximity of engine compartment Use the Proper Power Supply This product is designed to operate with a 12 volt DC negative ground battery system Protect the Disc Mechanism Avoid inserting any foreign objects into the disc slot Misuse may cause malfunction or permanent damage due to the precise mechanism of this unit CAUTION THIS MOBILE CD PLAYER IS A CLASS I LASER PRODUCT THIS UNIT USES A VISIBLE INVISIBLE LASER BEAM WHICH COULD CAUSE HAZARDOUS RADIATION IF EXPOSED DIRECTLY BE SURE TO OPERATE THE MOBILE CD PLAYER AS INSTRUCTED USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OR PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE DO NOT OPEN COVERS AND DO NOT REPAIR BY YOURSELF
5. button 20 on the control panel for less than one second to advance to the next track on the CD The selected track number will appear on the display Press and hold the up gt gt 21 or down lt lt button 20 for gt 1 second to fast forward or fast reverse through the disc CD play starts when the button is released Play Pause Disc Playback 1 PAU Press the 1 PAU button 12 to suspend disc play Press the 1 PAU button again to resume disc Play Intro Scan 2 INT Press the 2 INT button 13 on the control panel to play the first 10 seconds of each track sequentially Press 2 INT again to stop Intro Scan and resume normal play at the current track Repeat Play 3 RPT Press the 3 RPT button 14 during disc play to repeat play the current track Press 3 RPT again to stop repeat play Random Play 4 RDM Press the 4 RDM button 15 on the control panel during disc play to play all tracks on a CD in random shuffled order Press 4 RDM again to stop random play MCD5060 SPECIFICATIONS CD Signal to Noise Ratio 0 0 0 n gt 70dB Sampling IFrequericy 5 ptc ted eats rte ncn Seon arenas Atel wife ee meee eles 44 1Khz Quantization Bits 030 4024 c rope XR E we heaped E de eas 1 bit Frequeri y edes be aca aoe den a aged reed edere OE Ded ts 5 20 000Hz Channels RR RS E RUE RU OUR Ra 2 Channel Stereo FM Radio Frequency Range suntin ride xe due ded Roe
6. PLEASE REFER SERVICING TO A QUALIFIED TECHNICIAN WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS EQUIPMENT DIRECTLY TO WATER REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK AND INTERFERENCE USE ONLY THE RECOMMENDED ACCESSORIES THIS DEVICE IS INTENDED FOR CONTINUOUS OPERATION DISC NOTES Compatible Disc Types Table 1 General Disc Information Disc Type Logo Bi sis Sit Playback Time Audio CD 12 cm single side 74 minutes ete Os JG DIGITAL AUDIO DIGITAL AUDIO RECORDABLE REWRITABLE NOTE CD R and CD RW discs will not play unless the recording session is closed and the CD is finalized Disc Maintenance A dirty or defective disc may cause sound dropouts while playing Before playing wipe the disc using a clean cloth working from the center hole towards the outside edge Never use benzene thinners cleaning fluids anti static liquids or any other solvent Never touch Wipe clean from the under side the center to the of the disc edge Do not bend Insert label side up Be sure to use only round CDs for this unit and do not use any special shape CDs Use of special shape CDs may cause the unit to malfunction Do not stick paper or tape on the disc Do not use CDs with labels or stickers attached or that have sticky residue from removed stickers Do not expose discs to direct sunlight or heat sources such as hot air
7. a pencil or any non metallic object to press and hold the RESET button for five seconds to reset the main unit The unit will return to the factory default settings The reset button should be activated for the following reasons initial installation of the unit when all wiring is completed function buttons do not operate error symbol on the display NOTE If after pressing the RESET button the unit still does not function normally use a cotton swab soaked in isopropyl alcohol to clean the socket on the back of the control panel Audio Menu Press the volume control button 4 on the control panel to access the Audio Menu You can navigate through the Audio Menu items by pressing the volume control button repeatedly Once the desired menu item appears on the display adjust that option by turning the volume control knob within 5 seconds The unit will automatically exit the Audio Menu after five seconds of inactivity The following menu items can be adjusted Volume Level Use the volume control knob to adjust the Volume level from 00 lowest to 100 highest Bass Level Use the volume control knob to adjust the Bass level range from 10 to 10 Treble Level Use the volume control knob to adjust the Treble level range from 10 to 10 Balance Use the volume control knob to adjust the Balance between the left and right speakers from 10L full left to 10R full right BAL L R represents
8. an extremely important part Be careful not to damage it by pressing on it with fingernails pens screwdrivers etc If the DCP is dirty remove debris with a soft dry cloth only You can use a cotton swab soaked in isopropyl alcohol to clean the socket on the back of the DCP MCD5060 WIRING FUSE o o Lo ANTENNA JACK OJ ANTENNA SOCKET 20 PIN 1 AUDIO POWER HARNESS See Figure 1 LEFT FRONT WHITE BLACK LF RCA TO RCA CABLE not supplied REAR LINE OUT GREY BLUE BLACK YELLOW RIGHT FRONT GREY BLACK RF jp WHITE LF LEFT REAR c GREEN BLACK LR GREY RF n RIGHT REAR VIOLET BLACK RR jp GREEN LR VIOLET RR EE ES AMP e um 80 um 35 Power Antenna Connect to power antenna or amplifier If not used tape bare end of wire Ground Connect to ground terminal or clean unpainted metal part of chassis 1
9. ducts or leave them in a vehicle parked in direct sunlight where there can be a considerable rise in temperature inside the vehicle NOTE A disc may become scratched although not enough to make it unusable depending on how you handle it and other conditions in the usage environment These scratches are not an indication of a problem with the player MCD5060 INSTALLATION Before You Begin 1 Disconnect Battery Before you begin always disconnect the battery negative terminal 2 Remove Transport Screws Important Notes Before final installation test the wiring connections to make sure the unit is connected properly and the system works Use only the parts included with the unit to ensure proper installation The use of unauthorized parts can cause malfunctions Consult with your nearest dealer if installation requires the drilling of holes or other modifications to your vehicle Install the unit where it does not interfere with driving and cannot injure passengers if there is a sudden or emergency stop If the installation angle exceeds 30 from horizontal the unit might not give optimum performance This unit is not waterproof and is intended for interior mounting applications only Exterior mounting of the unit requires use of an ASA approved marine housing Avoid installing the unit where it will be subject to high temperatures from direct sunlight hot air or from a heater or where it would be subject
10. station press the SCAN button again Local Distant LO DX During radio operation received signals are usually in stereo mode as indicated by the ST icon however when the signals are weak or intermittent you can activate the Local LOC mode by pressing the LO DX button 9 LOCAL appears on the display on the control panel This mode favors access to local stations whose signals are much stronger thereby improving radio reception Press the LOC button again to terminate Local receive mode Preset Stations Six numbered preset buttons store and recall stations for each band Store a Station Select a band if needed then select a station Hold a preset button 12 17 for three seconds The preset number will appear in the display Recall a Station Select a band if needed Press a preset button 12 17 to select the corresponding stored station Automatically Store Preset Scan AS PS Automatically Store Select a band if needed Press AS PS 11 on the control panel for more than three seconds to automatically select six strong stations and store them in the current band The new stations replace any stations already stored in that band Preset Scan Select a band if needed Press AS PS 11 to scan stations stored in the current band The unit will pause for ten seconds at each preset station Press AS PS again to stop scanning when the desired station is reached Loudness Control B Press the B but
11. to excessive dust dirt or vibration Be sure to remove the control panel before installing the unit DI N Front Rear Mount This unit can be property installed with either a Front conventional DIN front mount or Rear DIN rear mount installation utilizing threaded screw holes at the sides of the unit chassis mount For details refer to installation methods A and B DIN Front Mount Method A 1 Remove the detachable front panel if it is attached to the chassis by pushing the REL button 2 Slide the mounting sleeve off of the chassis if it has not already been removed If itis locked into position use the removal keys supplied to disengage it The lt removal keys depicted in Removing el the Unit on page 3 3 Check the dashboard opening size by sliding the mounting sleeve into it If the opening is not large enough carefully cut or file as necessary until the sleeve easily slides into the opening Do not force the sleeve into the opening or cause it to bend or bow Check that there will be sufficient space behind the dashboard for the radio chassis 4 Locate the series of bend tabs along the top bottom and sides of the mounting sleeve With the sleeve fully inserted into the dashboard opening bend as many of the tabs outward as necessary to firmly secure the sleeve to the dashboard 5 Place the radio in front of the dashboard opening so the wiring can be brought through the mounting sleeve Bend Tabs
12. E RE deben 87 5 107 9MHz Intermediate Frequency 10 7MHz Usable 5 gt 15dB at S N 30dB Stereo 25dB at 1KHz Nu pm P 50dB AM MW Frequency Range va erria ead ca orem tese O ep ec Ed 530 1710KHz Intermediate Frequency 450KHz Usable Sensitivity llli gt 45dB SIN alio cetus a atria retta hited tue dude 40dB General Operating DC 11 14 4 Grounding Systemi 1 42 ds toca cad uber Don RUD EE mad Dance Negative Ground Speaker Impedance lt s cenrt eee eee 4 ohms Power Outp t acted Debs eet date edd 40W x4 eu TROUBLESHOOTING Symptom Cause Solution No power The vehicle s ignition is not If the power supply is properly on connected to the vehicle acces Sory terminal switch the ignition key to ACC The fuse is blown Replace the fuse Disc cannot be loaded or ejected Presence of CD disc inside the player Remove the disc in the player and insert the new one Inserting the disc in reverse direction Insert the compact disc with the label facing upward Compact disc is extremely dirty or disc is defective
13. L Press the REL button 3 to release the control panel Power On Off Press the button 1 to turn the unit ON or OFF Volume Control To increase the volume rotate the volume control knob 6 clockwise To decrease the volume rotate the volume control knob counter clockwise When the volume is adjusted the volume level is shown on the display panel as a number ranging from 00 lowest to 100 highest Mute Press the MUTE button 8 on the control panel to mute the audio output Mute will appear on the display Press MUTE again to restore the audio output to the previous level Mode Press the MODE button 5 on the control panel to select a different mode of operation as indicated on the display panel Available modes include Radio CD and AUX In optional Auxiliary Input Auxiliary Input 1 Connect the external signal to the Aux In jack 22 located on the front of the control panel 2 Press the MODE button to select Aux In mode 3 Press MODE again to cancel Aux In mode and return to previous mode Display D Press the D button 18 on the control panel to view the clock The LCD will display the clock for 5 seconds then return to the previous display mode Clock Adjustment With the clock displayed press the D button 18 until the LCD flashes Press the up gt gt 21 button to adjust the hours or the down button 20 to adjust the minutes Reset After releasing the control panel use
14. an equal balance between the left and right speakers Fader Use the volume control knob to adjust the Fader between the rear and front speakers from full rear to 10F full front FAD R F represents an equal balance between the rear and front speakers MCD5060 TUNER OPERATION Cla N HIT Gar 1 ia 7 us ay J Select a Band Press the B button 19 on the control panel to change between three FM bands and one AM band Each band stores up to six preset stations Tuning Auto Seek Tuning Press the up gt gt 21 or down lt lt button 20 on the control panel for less than three seconds to move to the next station automatically Manual Tuning Press the up gt gt 21 or down lt lt button 20 for more than three seconds to enter manual tuning mode Press the up gt gt 21 or down lt lt button to change the radio frequency number up or down one step The radio signal strength meter indicates the strength of the current radio station broadcast X Worst 7 ex Best Reception Scan Press the SCAN button 10 to automatically search for stations Each available station will flash on the display for a few seconds before the next is searched To select a flashing
15. com 2006 ASA Electronics Corporation v 071806 10
16. gned are fitted Tighten the screws at 2 places on each side Do not exceed M5 x 9 MM maximum Mounting Screw size Longer screws Bracket 7 Y may damage components inside the chassis 4 Wire the new radio to the vehicle as outlined in the Universal Installation instructions 5 Mount the new radio assembly to the dashboard or center console using the reverse procedure of step 1 Screws 2 Dashboard 1 1 1 1 Hook Remove NOTE The mounting box outer trim ring and half sleeve are not used for method B installation Reconnect Battery When wiring is complete reconnect the battery negative terminal Detachable Control Panel DCP Removing the Detachable Control Panel DCP pe 1 the power off 2 Press the REL button 3 Remove the Attaching the DCP PANEL RELEASE 1 Attach the panel at the right side first with point B on the main unit touching point A on the DCP as shown in the diagram 2 2 Press the left side of the DCP onto the main unit until a click is heard CAUTION 1 DO NOT insert the DCP from the left side Doing so may damage it The DCP can easily be damaged if dropped or subjected to a strong shock When the release button is pressed and the DCP is unlocked the vehicle s vibrations may cause it to fall To prevent damage to the DCP always store it in a protective case after detaching it The rear connector that connects the main unit and the DCP is
17. it Removing the Unit To remove the radio after installation Dashboard 1 Trim Plate Installation Push the trim plate against the chassis until it is fitted You must do this before you install the control panel otherwise it can t be attached Insert fingers into the groove in the front of frame and pull out to remove the frame When re attaching the frame point the side with a groove downwards and re attach lt Insert the removal keys straight back until they click and then pull the radio out If removal keys are inserted at an angle they will not lock properly to release the unit Removal Key uu MCD5060 DI N Rear Mount Method B This unit has threaded holes in the chassis side panels which may be used with the original factory mounting brackets of some vehicles to mount the radio to the dashboard Please consult with your local mobile stereo shop for assistance on this type of installation 1 Remove the existing factory radio from the dashboard or center console mounting Save all hardware and brackets as they will be used to mount the new radio 2 Carefully unsnap the plastic trim ring from the front of the new radio chassis Remove and discard the trim ring J 1 X o 3 Remove the factory mounting brackets and hardware from the existing radio and attach them to the new radio Select a position where the screw holes of the bracket and the screw holes of the main unit are ali
18. ton 19 on the control panel to turn the Loudness function on off When Loudness is activated the display will show for a few seconds Preset Equalizer PEQ Press the PEQ button 7 to select from the following preset equalizer functions FLAT gt CLASSIC gt POP M gt ROCK gt DSP OFF When DSP OFF is selected the EQ function is controlled by the Bass Treble settings Stereo The unit will automatically pick up an FM stereo signal when available When in stereo mode the ST icon appears in the display When no stereo signal is available the unit will automatically revert to mono operation and no icon will be displayed Ep MCD5060 CD OPERATION 40 warts x4 5060 lt LLL f Y Inv Zee i Ne 2f 6x3 i m L 5 1 lt 6 isc Lavon Tages gt EE Insert and Eject Disc Insert a disc label side up with the unit turned on S CDP will display on the LCD for about 2 seconds and the unit will play the first track on the disc Press the eject button 2 to stop disc play and eject the disc The unit does not have to be turned on to eject the disc 6000090000020 A Controlling Disc Playback Track Select Press the up gt gt 21 or down
Download Pdf Manuals
Related Search