Jeep 50-0284x-015 Series User's Manual
Contents
1. FIGURE 6 II INSTALLATION OF CONSOLE IF SPEAKER UPGRADE KIT WAS PURCHASED INSTALL PER INSTRUCTIONS PROVIDED FIGURE 7 11 Raise console item 8 pg 2 into approximate position against headliner Loosely install using 2 two 6 32 x 3 4 screws item 2 pg 2 through the smaller holes in bracket on console into threaded clips on front mounting bracket See Figure 7 12 Using a scribe or similar tool align hole in rear of console with slot in rear mounting bracket Loosely secure rear of console using 1 one 8 x 1 1 2 screw item 4 pg 2 Make sure console alignment is straight then tighten 2 two 6 32 screws previously installed See Figure 7 13 14 15 16 Release video screen from locked position Lower video screen to viewing position for access to mounting location in top of video system housing Raise video system into approximate position and connect all wiring to components Connect wiring and cabling to video system per instruction included with video system Check function of all component and lights See operating instruction for video system operations check For further assistance refer to the video system manual for the technical support phone number listed for your area Insert video system into opening in console FIGURE 8 Note Make sure wires do not get pinched between video system and console Align holes in housing with clips in mounting bracket Secure using 4 four 6 32. TA yi ot E emi June 2 1999 Printed in the U S A I PREPARATION OF VEHICLE INTERIOR 1 Using the rear edge of O E console as a reference location carefully measure amp trim headliner as shown Use a razor knife to score the first layer and scissors to cut remaining layers Caution Before cutting headliner material check for wiring or other componentry above headliner Cut only where indicated Wear safety goggles when cutting headliner material Make sure that the 9 amp 7 cuts are centered left to right in vehicle See Figure 1 DO NOT OVERCUT HEADLINER 2 Scribe a center line on the sheet metal roof of the vehicle from front to rear of opening in headliner This will be used for bracket alignment See Figure 1 FIGURE 1 3 Remove and retain 1 one screw which secures front O E console Pull downward to release console See Figure 2 FIGURE 2 4 Using a 3 8 drill bit make an access hole in rear of plastic bracket Caution Drill toward rear of vehicle See Figure 3 5 Construct a jumper harness that will connect the vehicle s dome light wires to the lights in video system Connect the white wire to the O E pink wire Connect the black wire to the O E yellow green wire See Figure 3 6 Using a test light test function of lights 7 Install O E console FIGURE 3 8 Insert rear mounting bracket item 6 pg 2 with the bent edges downward Slide bracket rearward
3. 2x 3 4 screws item 2 pg 2 and 4 four 3 5mm washers item 3 pg 2 See Figure 8 Caution Do not overtighten screws 17 Tighten screw previously installed to secure rear of console to headliner Caution Do not overtighten screws or damage to vehicle roof may occur 18 Raise video screen into locked position 19 Install speaker grille item 9 pg 2 Align clips in grille with holes in console and press firmly See Figure 9 20 If speaker upgrade kit was not installed install cover plate item 10 pg 2 at front of console and secure using 2 6 X 1 2 screws item 5 pg 2 21 Install cover plate decal item 11 pg 2 FIGURE 9
4. INSTALLATION INSTRUCTIONS FOR 50 0284x 015 SERIES 1181313 JEEP GRAND CHEROKEE OVERHEAD CONSOLE for use with FLIPDOWN VIDEO SYSTEM These instructions are intended for use only by experienced professionals in the automotive customizing business Special tools and equipment as well as specialized handling and care of product during installation may be required Before beginning this installation carefully read through the following instructions Use extreme care when cutting headliner material Check for wiring or other componentry above headliner material Cut only where indicated Materials Tools required for this installation 1 2 Phillips screwdriver 2 Powered screwdriver or drill with adapter 3 Awl or similar tool 4 Razor knife or similar 5 18 GA wire 4 6 6 Scissors 7 5 16 Hex Socket Bit 8 Safety Goggles 9 Test light 10 3 8 Drill Bit 11 Audiovox Series 640 650 Video Module NOT FOR VEHICLES EQUIPPED WITH SUN ROOF June 2 1999 INSTALLATION INSTRUCTION 44 0031A Printed in the U S A MATERIALS PROVIDED FOR INSTALLATION ITEM 1 SAANIAM SR WN pd p a Description SCREW 10 X 1 2 HWH SCREW 6 32 X 3 4 PPH WASHER 3 5 mm SCREW 8 X 11 2 PWH SCREW 6 X 1 2 PFH REAR MOUNTING BRACKET FRONT MOUNTING BRACKET CONSOLE SPEAKER GRILLE COVER PLATE COVER PLATE DECAL INSTALLATION INSTRUCTION 44 0031A Q lt Re eR Rk SE ND AORA mMm P z a be A J 3
5. between headliner and roof until tabs engage rear O E roof brace Align slots in bracket with center line scribed on roof See Figure 4 Note There is a foam sealer between O E braces and roof of vehicle It may require a little force to fully engage tabs of bracket if foam is in that area FIGURE 4 Ly a n a Pr At A te ba TS eS coi eye DET aa at ke fea ee cee ee 9 Install front mounting bracket Item 7 pg 2 over rear mounting bracket and align slot with centerline scribe and edge of bracket with front O E brace Secure using 4 four 10x 1 2 screws Item 1 pg 2 See Figure 5 FIGURE 5 10 Install and route all video and audio cables and any other added component requirements to their respective places in the vehicle Refer to component installation instructions for wiring diagrams The suggested routing of the video system cable is as follows Above the headliner from video system to C pillar Down the C pillar to the floor Route the power lead to an accessory controlled source Connect the ground lead to the vehicle chassis Route the remaining wiring RCA plugs Remote Sensor extension etc to the VCP location See Figure 6 Connect per instructions included with the video system If video system if to be used as a television install an appropriate antenna per instructions included with the antenna actessiry controlled source T 4 T g TE a VCP location
Download Pdf Manuals
Related Search