Jasco 19208 User's Manual
Contents
1. Push Button Jumpers Chime Jumpers Jumpers 1 6 are used to select 1 of 64 possible home security codes To change the house code add or remove jumpers as needed It is recommended to change only one jumper at a time and then test the system for proper operation Positions 1 6 on the chime and pushbutton must match exactly on Push Button Mounting Instructions Note Avoid mounting the push button on metal surfaces as it may result in a reduced range of transmission Do not mount in an area of rain direct weather a Removing the back cover b Replacing the back cover 1 Push buttons are typically mounted at the same height as the door knob or handle between 36 and 44 above the floor 2 Before mounting choose a mounting location that is not farther than 150 feet from the chime unit location Not farther than 150 feet Place push button where you would like to mount and test operation with the chime as close to it s final location as possible If it works mount button here Do not mount in an area of rain direct weather If it does not work see TROUBLESHOOTING Use back cover of push button as a template to mark two screw holes Drill two holes with 3 32 drill in marked locations Secure back cover to the mounting surface with two supplied mounting screws Press front housing onto back cover Test Operations if chime does not work see TROUBLESHOOTING Chime Unit Mounting Instructions N2. the table below Chime Sound Table Position F 8 9 Westminster ON OFF OFF Ding Dong OFF ON OFF Knock OFF OFF ON Bronze Chime ON ON OFF Cuckoo Clock ON OFF ON Foghorn OFF ON ON Gong ON ON ON ON Add a jumper to a location OFF Remove jumper from a location 4 Remove or add the jumpers to match the table 5 Store unused jumpers as shown in the picture Parking the jumper on an open set of pins The two jumpers on the left are in the parked position Setting The House Security Code Each chime component has jumpers for setting the house security code In most cases you will not need to change the factory settings for the security code If your chime activates intermittently or does not work at all you may be able to solve the problem by changing your security code as Str Cleo sake in Plt es The chime and pushbutton must be set to the same house security code for the combination to operate together Note The push button has 3 additional jumpers that are used to set the chime tune that will play The chime tune jumpers do not affect the house security code 1 Remove power or batteries from the chime 2 To remove the batteries from the pushbutton open the pushbutton case as shown below 3 Locate the House Security Code door and screw located on the back of the AC Chime Remove the screw and take off the door 4 Locate the chime and pushbutton jumpers shown below Mw i gt vv
3. GE Model 19208 www jascoproducts com Wireless Door Chime Kit Installation Instructions for Battery Operated Wireless Door Chime Kit Prior to Installation the Try Me feature must be removed 1 Remove the battery cover on the chime 2 Unplug the red and white wires inside the battery compartment 3 Remove the battery pack and discard appropriately Required Tools Small flat blade screwdriver drill drill bit and phillips screwdriver Included Hardware 2 Plastic screw anchors 2 4x20mm screws for anchors 2 3x20mm screws 2 Double sided adhesive pads The wireless door chime Kit has two components Chime receiver Push Button Transmitter Chime Tune Setting All wireless chimes may have more than one push button The chime tune for each push button is set with jumpers 7 9 Single Push Button Kit If you purchased a kit with a single push button the chime tune will be set to Ding Dong from the factory Dual Push Button Kit If you purchased a kit with two push buttons one push button will be set to Ding Dong and the other push button will be set to Westminster from the factory The following instructions explain how to change the tune on any wireless push button 1 Remove the battery from the push button transmitter 2 Locate the 9 position jumper shown below 9 position jumper This pushbutton is set for Ding Dong Chime since 7 off 8 on and 9 off 3 Select the desired chime sound from
4. ct to the following conditions 1 This device may not cause harmful interference and 2 This device must accept interference received including any interference that may cause undesired operation For technical support contact Jasco Products Company at 1 800 654 8483 or www jascoproducts com Made in China B is a trademark of General Electric Company and is used under license to Jasco Products Company LLC 311 N W 122nd Street Oklahoma City OK 73114 www jascoproducts com Rev 1 07 19208
5. ote Avoid mounting the push button on metal surfaces as it may result in a reduced range of transmission ieee Select chime mounting location Use the supplied chime template to mark mounting holes Drill 1 4 holes at marked locations Insert supplied wall anchors into the holes Insert two of the supplied screws into the anchors setting the screw heads extending about 1 4 from mounting surface 6 Place the chime unit s keyhole slots over the screws and press down on the chime unit to secure it a wy Eq Lots Operation T Slide power switch to On to turn on the chime 2 Gently press transmitter button to sound chime Troubleshooting Chime doesn t work 1 Make sure push button switch is depressed and held for at least 1 second 2 Make sure plastic tag is removed from battery 3 Make sure house code switches 1 6 on chime and push button match exactly 4 Verify battery orientation in push button 5 Try fresh batteries 6 Make sure chime is not farther than 150 feet away from push button 7 Ensure push button is not mounted on metal near metal studs or near the floor Try a new location for the chime e Functional range may be adversely affected by one or more of the following factors weather radio frequency interference low transmitter battery and obstructions between the transmitter and receiver This device complies with Part 15 of the FCC rules Operation is subje
Download Pdf Manuals
Related Search