Jasco 10167 Instruction Manual
Contents
1. g 2Pin 3Pin Link Fixtures Up to 22 1 2 Apart BULB REPLACEMENT INSTRUCTIONS See the label on the fixture for replacement bulb type information Do not replace with any other wattage of fluorescent bulb 1 Turn the fixture off and allow bulb to cool before handling 2 Remove the lens diffuser by lightly pulling the front edge while pulling downwards The lens diffuser should pop out easily See Figure 8 3 Remove the bulb by grasping the ends of the bulb and rotating until the bulb becomes loose Pull straight out from the lamp holder Be careful not to drop the bulb See Figure 8 4 Grasp the replacement bulb in the same manner and reinsert into the lamp socket and turn tube until it is securely held in place Do not use excessive force when installing bulb Fig 8 Lens Diffuser front edge Lente Difusor borde frontal 3 YEAR LIMITED FIXTURE WARRANTY Jasco Products warrants that the fixture will be free of defects in material and workmanship for three years from date of purchase This warranty does not apply to the bulb This fixture warranty is limited to repair or replacement at Jasco s option Damage caused by modification abuse or misuse is not covered Jasco makes no other warranty express or implied of merchantability or fitness for a particular purpose In no event shall Jasco be liable for special incidental or consequential damages Some states do not allow limi2. WARNINGS TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK OR INJURY TO PERSONS Risk of electric shock Risk of burn Allow bulb to cool before handling Bulb may shatter and cause injury if WARNING Risk of Fire A maximum of 10 fixtures can be added to or linked together in an existing circuit Not intended for illumination of aquariums Not intended for recessed installation in ceilings or soffits Not intended for surface installation inside built in furnishings such as kitchen cabinets china cabinets or trophy cases Do not conceal power supply cord inside a wall ceiling soffit kitchen cabinet or similar permanent structure Do not run the power supply cord through holes in walls ceilings or floors Do not use in wet locations Use indoors only Turn power off before servicing see instructions Use only insulated staples or plastic ties to secure the cords Route and secure the cords so that they will not be pinched or damaged broken Do not use excessive force when installing bulb SAVE THESE INSTRUCTIONS IN A LOCATION CLOSE TO YOUR CABINET SO YOU CAN REFER TO THEM AT A LATER TIME IMPORTANT SAFETY INSTRUCTIONS This portable lamp has a polarized plug one blade is wider than the other as a feature to reduce the risk of electric shock This plug will fit in a polarized outlet only one way If the plug does not fit fully in the outlet reverse the plug If it still does not fit contact a qualif
3. e 4 C Vertical Mount Horizontal Mount N Lug a Fig 2 Bencil Mark lt oo Fig 3 4 x Fig 5a sij Fig 1 E 5 6 h Horizontal Mounting Position Place the fixture in a location where you want it mounted Mark the position of the fixture on one end with a pencil This is a reference mark This will be the outer most edge of the fixture Make sure the switch will be accessible when the fixture is mounted Slide the first right angle lug into the end of the fixture as far as it will go See Figure 5 Using the first screw provided affix the first lug to the mounting surface See Figure 5a Place the second right angle lug inside the track at the opposite end of the fixture Slide the lug in as far as it will go Using the second screw provided affix the second lug to the mouning surface Proceed to Step 10 4 10 Attach each individual fixture with the 18 45 72 cm quick connect cord provided in the installation kit A maximum of 10 fixtures can be connected together See Figure 6 and Figure 7 See product label located on the fixture for electrical rating 11 Attach the quick connect power cord with the plug and three pin quick connector to the fixture closest to the outlet See Figure 6 and Figure 7 12 Plug fixture into a 120VAC 60Hz outlet Quick Connect Conexi n R pida Fig 6 Fig 7 ELECTRICAL CORD CAN BE ROUTED AROUND CORNERS TO SUIT THE INSTALLATION
4. ied electrician Never use with an extension cord unless plug can be fully inserted Do not alter the plug Read entire installation procedure before you begin INSTALLATION PROCEDURE Suitable for under cabinet mounting 1 Consult a local licensed electrician or electrical contractor if you are not sure about the installation 2 DO NOT ATTEMPT TO INSTALL FIXTURE WHILE PLUGGED IN 3 Select a suitable dry mounting location for use indoors only Make sure mounting surface is capable of supporting the fixture 4 Itis recommended that a 1 16 15 cm pilot hole be drilled in the mounting surface for wood screws Vertical Mounting Position 5 Place the fixture in a location where you want it mounted Make sure the switch will be accessible when the fixture is mounted Mark the position of the fixture on one end with a pencil This will be the outer most edge ofthe fixture See Figure 1 Place the lug on the inside of the line and affix with the screw provided through the round hole to the mounting surface 6 Slide the fixture over the mounted lug until it stops See Figure 2 7 Place the other lug slightly inside the track at the opposite end of the fixture so the outer most round mounting hole is visible See Figure 3 8 Using the second screw provided affix the second lug to the mounting surface 9 Slide the fixture back over the second lug so that both lugs are hidden completely from view See Figur
5. tations on how long an implied warranty lasts and or do not allow the exclusion of consequential damages so the above limitations may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary based on your place of residence To obtain repair or replacement information under the terms of this warranty return the fixture and proof of purchase along with owner s name and address postage prepaid to Jasco Products Company LLC 10 E Memorial Rd Oklahoma City OK 73114 Linkable Fluorescent Undercabinet Fixture B is a trademark of the General Electric Company and is used under license to Jasco Products Company LLC U 1o E Memorial Rd c us Oklahoma City OK 73114 www jascoproducts com LISTED 03 23 10 10167 10168 10169
Download Pdf Manuals
Related Search