Jacuzzi Vantage Whirlpool Bath User's Manual
Contents
1. 3 PRONG PLUG DUPLEX RECEPT 4 MIN NOT PROVIDED Drain Information A drain overflow assembly purchased separately from the bath must be installed on the bath water tested and connected to the sanitary system of the house After opening the carton inspect for damage and verify that the kit is of the proper finish If a Jacuzzi Whirlpool Bath drain overflow is being installed note that the waste flange strainer overflow cover and cover screws are packaged in a separate package within the kit to protect the trim finish Follow the installation instructions provided with the drain overflow kit After the drain is fully installed test for proper drainage If the unit does not drain properly rectify this condition before proceeding with the installation Jacuzzi Whirlpool Bath is not responsible for removal and or reinstallation costs NOTE Watertight installation of the drain is the installer s responsibility Any occurrence of drain leakage is excluded from the Jacuzzi Whirlpool Bath warranty coverage of this product CAUTION A nonflammable protective barrier must be placed between soldering work and bath unit to avoid possible damage to the bath Clean Up After Installation To avoid dulling and scratching the surface of the bath never use abrasive cleaners A mild liquid deter gent and warm water will clean soiled surfaces Remove spilled plaster with a wood or plastic edge Met2. S amp 3 53 gt gt Dow gg gt Z gt PAPA lt 333 0823 285 of Ss00 ol 20 F535 Ta 5 FO 4490 GG lt 93538 8 3 25706 S lt O7 zE Q 3 23 a209 ga 8834 dias 28 wet abw wl r SN 38 pr gt oa Se N p S588 s5 angre 228 v 225085 I NIGE 8 gt 2 85 g Be N 0000 I lt c 9953 5 od ED ME ate S 8 a y pen 5 COnane 332 05 al TG Sorta 250 O U D Om z 2 oo ET 2E 9 2 DSO ar 835 3 S 8 36 58 0 D 5948 25 agen 3 IOQ3ET 57 3 ol gt 326 I lt an S 2 mo lt JL9GE an 20 3 S 2 og Q a Qeon sg NS RQ gt JLI38 lt 8 26 Bl 3 S225 an DI Ss D PR Q 5 a Fay SA d 5 8525 aw Oxo HE fo 3985 D F Q SESS OM a aga lt 6 3 2 8 PEG IT amp v v EL oe 30 5 gt Dag 2 a c 0 RIS 253 3 0 NY 4899 a aa o 7 25 2 rn N S3 g D NI PS D o o gt 3270 D 0 50 3 d Q 5 3 g 2 798 3E ar Da lt Q g oo vo O PI a 2 D a sa amp a 25 5 N 9 S a 8 o BS o gt gc gt a a gt 9 35 si G 2 8 so O 8 z E 22 9 3 3 lt a 2 p Se Q AueueMm
3. bath must be able to support a total weight of approximately 805 pounds bath water and bather or 60 pounds per square foot If the subfloor is level no other preparation is necessary You can proceed to install the bath If the subfloor is not level you MUST level the entire surface prior to installing the bath The use of materials that shim or provide a level installation are allowed provided the method used will insure a level bath that is supported from the bottom Materials that may be used are a floor leveling compound mortar plaster or minimal expansion structural foam having a density of a minimum of 5 Ibs cubic ft however the bath must remain level in order for it to drain properly and the foam feet must make full contact with the mortar plaster or structural foam foundation The bath must be supported as outlined above Both sides of a joint or splice of subfloor should be level to each other When attaching baths with flanges to stud wall use shims to fill any gaps between the bath flange and studs The rim of the bath is not designed to support weight If finish material is to overlap or contact the bath the added weight must be fully self supporting The protective film liner inside the bath is used to prevent damage to the finish from shoes tools etc during installation Before installation remove liner to inspect for any defects reapply and do not remove until final cleanup The bath unit should be installed after constructi
4. to a circuit protected by a Ground Fault Circuit Interrupter CAUTION Operating the motor pump without suffi cient water in the bath can cause leaking and perma nent damage to the pump Before power is applied to the installation make sure the switch is in the OFF position to avoid pump damage If installation of an optional timer is desired refer to wiring instructions provided with the timer An optional timer is available from Jacuzzi Whirlpool Bath for 115 VAC operation Plumbing Pump jets and suction fittings for the whirlpool sys tem are factory plumbed in PVC schedule 40 piping All Jacuzzi Whirlpool Bath products are factory tested for proper operation and watertight connections prior to shipping If leaks are detected notify your Jacuzzi Whirlpool Bath Dealer do not install the unit Water Supply Consult local authorities for plumbing code require ments in your area IMPORTANT Proper installation of the fill spout plumbing and compliance with local codes is the responsibility of the installer Jacuzzi Whirlpool Bath does not warrant connections of water supply fittings and piping fill systems or drain overflow systems Nor is it responsible for damage to the bath which occurs during any installation procedure INTEGRAL SKIRT MOUNTING DETAIL FINISHING MATERIALS TE CAULKING BEAD REMOVABLE SKIRT ACCESS PANELS ELECTRICAL CONNECTION
5. EE S E O ES gt E rd z3 o ON 9 a gt w N gt 999 0900 23235 5 3 Ae NS RE E AE Ne A annan PD 8GEG 3005 O SUZ lt a 2 2g Seve 2z Tootoo S Sozo Q Ooms 88 8 dv s 38 p 3 8 B 3 38 2 4 Zz gt D PIE 3 Bolas 255 55 LORS 88S REP ASQAMS BOOS BOMROTEO OOF 0s lt lt ra 525 E p 8 205 SS5207 Be Bo ee 5535S S E28 eo ee SAGER TB EIASH SSR OAFOSESSO Sas ov o 333 lt lt D U voz 73000943 op g lt 20 024325 An9 F2o0a3v03200Q02a00Q00g o gt zZ3 30 8398 222908884 REEERE 225 20320 Crn lt Se sg ii Ragel gos D aga g axx Soro S5 LFY gea Ka BH 3gz2 282v00 2 PF osady P PIS D 2 3558 2 lt 933 34 JENA lt DALE 9 gt 73 8 8 aOF 2o0 20 5093 o oa D g S lt a too Os S2 30903 BS 2 2 83 350 SmogSsm3g pr Sz lt 392 BERRE 2353 SR rioel SRB age 0 B98 CST a T DE 2 KONG 2000 og asf ko O37 Q PEO OOD BS2Sak as 5Sa E 8200 3932 o9 503393233 oa OR sooo 253540 3 PR 22 3 332 200 sa sa gy FIT I lt o H Ep gt o53 530 5 Tue 2038 om ITE 5 GE o ms 228 xe as 8535 2 3o lt J23 3 vozo BH DIS ov e i 59 g 2 231 3 32233065 38 8s Z9 n333 fog om 3 20 Fa 2 3 m 2 a 95S o 03F32039 6 3 pe E 3 ab z 2588 o 2233 388082 ao 5 20 ang a aol 5 2300 e338 D 8 280025 23 ESSEN TE Do T lt S Q ao 5292c53 Oc D CA Dere or S ol 3 E oo 3 pecan z 2 ov FE ons 2223 253 8 SSDL R 28 Boc 9 53 i v g or LIONS 33 g agza oz
6. F EQUIPPED HOT SUPPLY FILL SPOUT COLD SUPPLY RECOMMENDED LOCATIONS FOR STEAM HEAD BLOCKING OPTICA 300 CONNECTIONS TO BODY TO SHOWER SPRAY JETS IF NOT EQUIPPED PLUG OFF OPTICA 300 MIXER AND TRANSFER FRANS VALVE COLD IN LINE FOR BODY SPRAY JETS IF EQUIPPED SUGGESTED PLUMBING LAYOUT REVERSE FOR RIGHT HAND VERSION SHOWER HEAD SPRAY 2 IF EQUIPPED Service Access Service access is through the removable panel in the integral skirt Allow a space of at least 8 away from the bath for skirt removal The skirt is designed to accommodate the added height of the tile linoleum or other floor coverings up to 1 1 4 above the floor and will be flush with the floor when installed When the bath is not installed with the skirt provide adequate ventilation minimum 30 square inch opening for cooling of the motor and sufficient air supply for jets Electrical Connections A separate 115 VAC 15 AMP circuit which must be protected by a Ground Fault Circuit Interrupter GFCI is required Because these units are manufactured with a safe convenient Magic Touch whirlpool ON OFF switch on the bath itself no remote switch or timer is necessary Install a 115 VAC 15 AMP duplex outlet to the studwall underneath the bathtub at least 4 above the floor Duplex outlet is not provided DANGER RISK OF ELECTRIC SHOCK Connect only
7. Vantage Whirlpool Bath Jacuzzi WHIRLPOOL BATH with Surround INSTALLATION INSTRUCTIONS Each whirlpool bath is arrives ready for installation completely equipped with motor pump assembly and plumbing and fittings necessary for whirlpool operation An optional drain overflow kit is available for installation on the bath le s 60 j 24 36 y 18 1 2 24 1 2 HA a END VIEW WITHOUT END VIEW WITH 9 3 8 BODY SPRAY JETS BODY SPRAY JETS SIDE VIEW SPECIFICATIONS TOTAL WEIGHT FLOOR OPERATING PRODUCT WATER ELECTRICAL DIMENSIONS MOTOR PUMP LOADING GALLONAGE WEIGHT PRESSURE REQUIREMENTS 60 1524 mm L 115 VAC 805 Ib 38 U S gal 238 Ib 40 psi min 115 VAC 32 813 mm W 3450 RPM 10 AMP 366 kg 144 liters 108 kg 2 8 Bar 15 AMP 84 1 2 2146 mm H 60 Hz 60 Ib sa ft 60 Hz Single Phase 293 kg sq m Requires dedicated separate circuit Use installation instructions provided with product Product specifications are subject to change without notice Optional Features Trim Kit Timer Drain Overflow Kit Lamp Package Pillow Optica 300 Shower Mixer Valve and SteamPro 120 Steam Generator Important Read complete instructions before beginning installation Remove the bath from the carton Retain the shipping carton until satisfactory inspection of the product has been made Do not lift the bath
8. al tools will scratch the surface Spots left by plaster or grout can be removed if lightly rubbed with detergent on a damp cloth or sponge Paint tar or other difficult stains can be removed with paint thinner turpentine or isopropyl alcohol rubbing alcohol Minor scratches which do not penetrate the color finish can be removed by lightly sanding with 600 grit wet dry sandpaper You can restore the glossy finish to the acrylic surface of the bath with a special compound Meguiar s 10 Mirror Glaze If that is not available use automotive rubbing compound followed by an applica tion of automotive paste wax Major scratches and gouges which penetrate the acrylic surface will require refinishing Ask your Jacuzzi Whirlpool Bath dealer for special instructions Operation For instructions see owner s manual PRODUCT SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE USE INSTALLATION INSTRUCTIONS SUPPLIED WITH PRODUCT Jacuzzi Whirlpool Bath has obtained applicable code standards listings generally available on a national basis for products of this type Itis the responsibility of the installer owner to determine specific local code compliance prior to installation of the product Jacuzzi Whirlpool Bath makes no representation or warranty regarding and will not be responsible for any code compliance Jacuzzi Whirlpool Bath P O Box 702168 Dallas TX 75370 2168 Service Support Call 800 288 4002 ED Printed on Recycle
9. by the plumbing at any time handle by the shell only Immediately upon receipt inspect the shell before installing Should inspection reveal any damage or defect in the finish do not install the bath Damage or defect to the finish claimed after the bath is installed is excluded from the warranty Jacuzzi Whirlpool Bath s responsibility for shipping damage ceases upon delivery of the products in good order to the carrier Refer any claims for damage to the carrier For definitions of warranty coverage and limitations refer to the published warranty information packed with the product All bath units are factory tested for proper operation and watertight connections prior to shipping Note Prior to installation the bath must be filled with water and operated to check for leaks that may have resulted from shipping damage or mishandling Jacuzzi Whirlpool Bath is not responsible for any defect that could have been discovered repaired or avoided by following this inspection and testing procedure FRAMING DETAILS RIGHT HAND SHOWN BLOCKING REQUIRED IF UNIT HEADER ON EDGE 4 IS INSTALLED IN SECTIONS 33 1 4 12 x 4 DRAIN EQ H CUT OUT Framing and Support The optional drain overflow of the bath extends below the bottom of the bath Note that this requires a cutout in the floor The floor structure beneath the
10. d Paper 6 1999 Jacuzzi Whirlpool Bath P592000 8 13 04 Printed in the U S A Jacuzzi Whirlpool Bath Limited Warranty Builder Group Bath Product WARRANTY COVERAGE Jacuzzi Whirlpool Bath the Company offers the following express limited warranty to the original purchaser of any Jacuzzi Whirlpool Bath Builder Group Bath Product unit who purchases the product for personal or single family use user The Company will repair or replace at its option the unit or its equipment in accordance with the following terms and conditions ONE YEAR LIMITED WARRANTY ON BATHS Our warranty on Builder Group Bath products is for one 1 year Our warranty covers the unit and factory installed components e g pump motor against defects in material or workmanship Warranty coverage begins on the date the unit was originally purchased by the user NINETY DAY PARTS ONLY LIMITED WARRANTY ON OPTIONS AND ACCESSORIES Our warranty on options and accessories manufactured by the Company is for ninety 90 days for parts only Our warranty covers options and accessories manufactured by the Company e g fill spout kits trim kits skirts against defects of material or workmanship Warranty coverage begins on the date the option or accessory was originally purchased by the user WARRANTY LIMITATIONS Our warranty does not cover defects damage or failure caused by the common carrier installer user or other person or resulting from wit
11. e has been permitted to inspect the unit during regular business hours within a reasonable time after the problem was reported by the user In order to obtain warranty service consult your local telephone book for the location of the nearest Jacuzzi Whirlpool Bath Authorized Service Agent Describe the problem and the Authorized Service Agent will inspect the unit and provide the required warranty service If you are unable to contact a Jacuzzi Whirlpool Bath Authorized Service Agent call or write Jacuzzi Whirlpool Bath Warranty Service Department P O Box 702168 Dallas TX 75370 2168 Call 1 800 288 4002 To obtain warranty replacement for factory installed components for Company supplied options and accessories manufactured and supplied by the Company call or write the above Provide a description of the problem and proof of purchase You will be instructed how to obtain replacements and where to return at your expense the failed component s option s or accessory ies All replacement parts equipment and repairs shall assume the remaining warranty period of the part s replaced The Company s warranty obligation shall be discharged upon tender of replacement or repair The customer s refusal to accept the tender terminates the Company s warranty obligation 1999 Jacuzzi Whirlpool Bath P592000 8 13 04 g 3 Oo 02 ETE 0 O as SS20 lt 2 U 329 0 y lt lt Oo 5 2 2
12. ffective Se A Jacuzzi Whirlpool Bath P O Box 702168 Dallas TX 75370 2168 vO EL 8 RESPONSIBILITIES OF OTHERS Inspecting the unit prior to installation is the responsibility of the installer or building contractor who acts on behalf of the user They are responsible for ensuring the unit is free of defect or damage Notices are placed on and in the unit and on the shipping carton advising the installer of this responsibility In the event of a problem the unit must not be installed The Company is not responsible for failures or damage that could have been discovered repaired or avoided by proper inspection and testing prior to installation Damage occurring in transit is the responsibility of the carrier The user or installer MUST open the crate and inspect the unit for damage when it is delivered If damage is discovered it must be reported immediately to the seller and the carrier in writing and an inspection requested Failure of the carrier to respond should be reported to the seller and the carrier Your freight claims should be filed promptly thereafter It is the responsibility of the installer building contractor or user to provide access for service The Company is not responsible for any costs relating to obtaining access for repair The user shall bear such costs and if appropriate must seek recovery from the installer Damage occurring to the unit during installation is the responsibility of the installer and or building c
13. hout limitation any of the following careless handling lifting unit by plumbing abrading finish etc including its own negligence modification of any type for any reason including modification to meet local codes improper installation including installation not in accordance with instructions and specifications provided with the unit connections supplied by the installer of the equipment improper voltage supply or unauthorized electrical modification misuse incorrect operation or lack of proper routine maintenance operation of the unit without specified minimum amount of water or at inappropriate water temperature use of abrasive or improper cleaners or acts of God such as lightning floods earthquakes etc In addition THE COMPANY WILL NOT BE RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES or losses arising from any cause e g water damage to carpet ceiling loss of use etc including its own negligence damages to respecting or resulting from plated parts when pool and or spa chemicals are used in the unit optional bath equipment not manufactured by the Company supplied by Dealer installer or the Company the unit s prior usage as an operational display or defects that should have been discovered before installation This limited warranty does not include labor transportation or other costs incurred in the removal and or reinstallation of the original unit and or installation of areplacement unit any costs relating to ob
14. ines spout pipes and valve plumbing do not project into the studwall pocket Installation Slide the bath into the framed opening and secure the front flanged sides to the 1x2 strips and the top flange to the header The bathtub should be level and supported along the base It may be necessary to disassemble the bath to install it Install the bathtub portion making sure it is level and properly secured to the floor and studwall blocking Apply abead of adhesive caulking to the top of the flange surface and place the middle section over the studs of the bath flange Push down firmly to assure that the middle section is seated and level Secure the top flange of the middle section to the studwall blocking and the sides to the 1x2 verticals Repeat the same caulking procedure for the top section and secure it to the header and 1x2 verticals If the bath with the surround is installed in one piece without being disassembled it is necessary to caulk all joints between the bath middle wall and top cap To make caulking the joints easier place masking tape on each side of the joint as shown in the illustration Apply a bead of caulking along the joint between the tape Smooth out the caulking with a tool or finger Remove tape after caulking has set ROUGH IN PLUMBING DETAILS FOR FIXED SHOWER HEAD 32 MIN 42 MAX Je lt ES SUPPLY LINES PRAY1 17 I
15. on of the studwall and rough plumbing is in place The bath may be installed as a single unit or if necessary disassembled and installed in three sections It is important that the framed pocket be plumb and square and that the framing members be located as detailed in the framing illustration If the bath unit is to be installed in an existing bathroom studwall additional studs must be added to the dimensions shown 2 HEADER DETAIL ov X 4 SHEET ROCK r SHEET ROCK INSERT HEADER Va 84 1 2 TO 84 3 4 gt eo s SIDE DETAIL TOP VIEW 1 X 2 SNe DOUBLE 2 x 4 Ks SHOWER SURROUND SHEET ROCK WALL DETAIL WALL STUD BLOCKING WOOD ENCLOSED WITH FIBERGLASS DRILL CLEARANCE HOLE 1 4 20 STUD CAULKING MASKING TAPE SHOWER SURROUND Rough Plumbing The locations of the valves fill spout and shower head should be marked and drilled before the bath unit is placed in position Where access to connections is limited allow enough flexibility in the supply lines for easier positioning of the valves after the unit is in place From stable reference points such as the subfloor and front of the double studs measure and note the locations of the fill spout valves and shower head arm To avoid obstructions during installation ensure that water l
16. ontractor and damage occurring thereafter is the responsibility of the user Failure of any optional equipment is the sole responsibility of the equipment manufacturer Options and accessories manufactured by the Company are warranted for ninety 90 days from the original date of purchase for parts only The Distributor or Dealer is responsible for knowing local code requirements and notifying the installing contractor and or user of these requirements at the time of purchase The Company is not responsible for costs to modify any product to obtain any code approval such as city county or state building codes WARRANTY SERVICE For the customer s benefit the Company maintains a list of independent service personnel to perform required warranty service repairs Such firms are not agents or representatives of the Company and cannot bind the Company by words or conduct The Company will provide the warranty service described above when the following conditions have been met the failure is of the nature or type covered by the warranty the user has informed an Authorized Jacuzzi Whirlpool Bath Service Agent or Warranty Service Department Representative of the nature of the problem during the warranty period conclusive evidence e g proof of purchase or installation is provided to the foregoing by the user proving that the failure occurred or was discovered within the warranty period an authorized independent service person or Company representativ
17. taining access for repair or loss of use damage including loss of sales profit or business advantage of any kind under any circumstances Bath units in commercial use are excluded from any warranty coverage if any addition deletion or modification of any kind whatsoever has been made to the unit or to any component Warranty coverage is provided in the United States of America only IMPLIED WARRANTIES All implied warranties of merchantability and fitness for a particular purpose are equal in duration with the express warranties set forth herein NOTICE This warranty gives you specific legal rights and you may also have other rights which vary from state to state There are no warranties applicable to Jacuzzi Whirlpool Bath products except as expressly stated herein or as implied by applicable state and federal laws The Company will not be responsible for any statements or representations made in any form that go beyond are broader than or are inconsistent with any authorized literature or specifications furnished by the Company Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages so the above limitations and exclusions may not apply to you RETURN OF WARRANTY CARD The attached Warranty Registration Card MUST be filled out by the purchaser within thirty 30 days from purchase and mailed to Jacuzzi Whirlpool Bath in order for this warranty to become e
Download Pdf Manuals
Related Search