Jacuzzi J-DREAM II User's Manual
Contents
1. Specifications 2 General Information 3 4 Packaging 5 Hardware Identification 6 Rough in 7 Base and Drain 8 9 Installation of Panels 10 16 Door Frame 17 Top Frame 18 Hose and Electrical Connections 19 21 Bonding 22 Final Plumbing 23 Front Panels 24 Cover 25 Completing the Installation 26 Part Il Operation and Maintenance 27 30 Warranty 33 34 Inspection and Shipping Claim Check for shipping damage upon receipt of the J Dream II Jacuzzi Whirlpool Bath is not responsible for damage to the J Dream II sustained during shipping If damage is evident before unpacking see instructions regarding shipping claims on the outside of the carton and immediately file a claim with the carrier Once the J Dream II has been removed from the carton and before it is permanently installed check the parts completely for damage resulting from shipping or handling All Jacuzzi Whirlpool Bath products are factory tested for proper operation and watertight connections prior to shipping If problems are detected immediately notify your Jacuzzi Whirlpool Bath dealer or Authorized Service Agent or call Jacuzzi Whirlpool Bath 800 288 4002 for Warranty Service NOTE Damage or defects which could have been discovered and repaired prior to installation and which are claimed after final installation of the J Dream Il are excluded from our warranty J Dream Il Owner s Manual o WHIRLPOOL BATH FRONT VIEW2. Panel 4 J Dream Il Owner s Manual Attach Brackets to Seat Wall Frames and L Bracket to left Angle Bracket Bolt remove top bolt from seat wall bracket and reinstall See below dimensions for bolt locations i Seat Wall fr p lt A MM Bolt remove top bolt from seat wall S bracket and reinstall See below dimensions for bolt locations N YM Seat Wall Side T Bracket 4 L MM Panel 1 Z3 54 Panels 1 and 4 YO not shown in this C illustration for clarity Angle Bracket with Velcroe strips o 9 Note only the left side has this L bracket installed J Dream Il Owner s Manual Attach Painted Angle Brackets to Panels 1 and 4 Note that each angle bracket has a notch on the top and bottom This notch does not get screwed against the side panels but faces out as shown in the side view for both left and right sides Do not tighten the screws at this time as the angle brackets will have to be aligned with the door frame holes Top View right side Side View left s
3. 28 Care and Maintenance of SteamPros Maintenance of the Steampros includes flushing and visually inspecting for water leaks To flush the units 1 Turn OFF power to the unit 2 To gain access to the SteamPros the seat wall equipment wall must be swung open To do so remove the three screws from door frame refer to page 17 diagram A Then remove right front panel Refer to page 11 and remove the four bolts indicated Swing seat wall open far enough to remove cascade line from cascade tee by loosening spring clamp refer to page 21 Swing seat wall fully open and turn the water supply OFF Unplug the SteamPros power cords and disconnect all plumbing Remove the SteamPros from their mounting refer to illustration below Flush the tanks out the drain plug can be removed with an 8 mm hexagonal wrench Reinstall SteamPros Turn ON the water supply and check for leaks Reattach cascade line Close seat wall reinstall bolts screws and panel Turn ON power to the unit oof Cc Cc J Unplug Power Cords Disconnect Copper Lines Disconnect Steam Lines e j Drain Plug IET D Remove Nuts Opposite side and Remove SteamPros from Studs 29 Troubleshooting Chart PROBLEM 1 Control is on and appears to be functioning but no steam PROBABLE CAUSE Steamer heating up High limit saf
4. NOTE In order to hear the TV audio the Pioneer CD Receiver AUX function must be setup to be ON To perform this setting If the unit is on press SOURCE and hold until the unit turns off Press FUNCTION repeatedly until AUX appears in he display Select AUX on and off with A V The status will be displayed AUX ON If power to the unit is interrupted the CD Receiver will have to be reset Note For units with AM FM radios the quality of AM reception will vary by locality Jacuzzi Whirlpool Bath is not responsible for the quality of AM reception Maintenance Routine Maintenance The shower head is equipped with a filter which must be occasionally cleaned of limestone and other deposits The filter is placed between the flexible hose and the shower head If limestone deposits are on the jet nozzles the shape of the water jets may be altered Remove and clean the nozzles occasionally Unscrew the nozzle to remove Clean it by soaking it in a moderate vinegar and water solution Do not use metal tools such as scissors or screwdrivers etc to clean the nozzle For routine cleaning of the dome and plastic surfaces such as the side panel the shower wall panel etc use a mild liquid detergent only Any normal polish can be used to keep acrylic surfaces shiny The glass panels can be cleaned with any glass cleaning product available on the market Do not use abrasives alcohol acetone ammonia or other solvents on any part of the J Dream
5. 3 eu Fg SOME arc TO REMOVE DOME 81 83 2057mm 2108mm C M 60 1524 mm TOP VIEW 60 1524mm 11 5 8 SERIAL NUMBER LOCATION 295mm AT TOP ON BACK OF REg EQUIPMENT SEAT WALL 42 1067mm SPECIFICATIONS TOTAL WEIGHT REQUIRED PRODUCT ELECTRICAL DIMENSIONS FLOOR LOADING WATER SUPPLY WEIGHT REQUIREMENTS 60 1524mm L 833 Ib 379 kg 6 gpm 23 liter min 525 Ib 240 VAC 3 Wire 42 1067mm W 47 6 lb ft 9 30 65 psi 239 kg 20 Amp 50 60 Hz 83 2108mm H 233 kg m 2 1 4 6 Bar Must be GFCI Protected Unit supplied with a 240 VAC 20 Amp 3 wire plug NEMA 6 20P PRODUCT SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE 2 SHIPPING WEIGHT 849 Ib 386 kg J Dream Il Owner s Manual Read all instructions before beginning assembly and installation General Assembly Information The J Dream Il shower unit is installed into a niche with the drain towards the left hand side of the unit as you face the shower door This manual details the assembly installation and operation After the drain water supply stub out and electrical supply are provided the shower unit should be assembled freestanding away from the walls of the room Next connect and static test the water supply lines The electrical connections should then be completed before the unit is moved into final position drain fit is rechecked and assembly is compl
6. access equipment After they have been connected and there is sufficient slack the cable ties may be tightened Feed the hot and cold water valve manifold supply valve 6 and 7 lines from the equipment side wall and connect as below Route the water filter line and control cable to the equipment side wall To Cascade Tee Control Cable To Valve 1 To Valve 3 To Valve 6 To Valve 7 From Water Filters Cold Water Supply with braided metal sheathing Hot Water Supply with braided metal sheathing To Manifold Steam Line with black insulation cover Fd Ss A CNN 20 CD Radio Speaker and Power Wires To Cascade Fitting To Jets To Steam Head J Dream Il Owner s Manual Right Seat Wall Equipment Wall Connect the hoses routed from the back wall as below grayed lines are pre attached Connect the controller line The red and black leads in the CD Radio wire bundle must be hooked up to the corresponding colored leads of the power supply Connect the speaker leads Connect the two SteamPro power cords after unraveling them ACARI JAEK Back of Right Seat Wall i P i CD Power and Bonding Speaker Wires Wire n A From Control Panel Valve oe zh rom Bottom of Mixer a B on Backwall From Bac
7. required warranty service If you are unable to contact a Jacuzzi Whirlpool Bath Authorized Service Agent call or write Jacuzzi Whirlpool Bath Warranty Service Department P O Box 702168 Dallas Texas 75370 2168 Call 800 288 4002 To obtain warranty replacement for factory installed components or Company supplied options and accessories manufactured and supplied by the Company call or write the above Provide a description of the problem and proof of purchase You will be instructed how to obtain replacements and where to return at your expense the failed component s option s or accessory ies All replacement parts equipment and repairs shall assume the remaining warranty period of the part s replaced The Company s warranty obligation shall be discharged upon tender of replacement or repair The customer s refusal to accept the tender terminates the Company s warranty obligation pues uonessibey AjueJeM
8. E 9 47 3 go S 8288 sssr paggorzc Sg e aa lt lt Ume 3 ct oj 4 g 2 o o3 FOSS DPSS f lt a aq 2 o EI eco Ge FS o g yo 9 58 c Og 2g 52oo o a ER o 37E 3 S22 9 of 3a go amp 9 S5 S of SBgoc fo SS pp E s3257 Oum 5 2 5 2278833 r ovg S988 qd 223 955 FE a 2 73e SE c B OX mogga Me 334 a725 Q Gwe g2 B53 EN 35 N BS S222895 3242 Zg29 v g2r 9a8 I 9282 5 p 5 az ge a OF BSB oo Is 2 FAS el D o F ooo m d c 9509 2lSone a orig 0 o N U Bo 8 sgor LPP 3 8 2 582 S gt 882 8 5 8 28 d d 9 o7 59 B a 3 Tasco Su z837 c S 9702 o Q Zeiz e x s c A oo EI 3 gL SE O age N O os o ox o I Q BROoZo D gt t Fors aos 32208 xe o s 8S 5202 o S PER9083 amp g gr oggA4 ge 2 2 393 Em S lt OOGS y ER A2Qo lt 9 3 220 Q E lt fo 21903 gt 22 ie E o 819 Qa s NS s8o o o aa 9 T fm 8 EXE gg r 6s 9 g S a F Ed o8 amp goo og 3 3 uS Q E 63 85 82 N 9 8 2d E B N O gE 3 5 EG o o zi gs EN Zr 9 2 Q aa o y 3 9 S oo N EI amp v S o D D E 8 lt amp oo o mf o p zh 35 a gp o ct Str 8 i a E gt 5 o o RESPONSIBILITIES OF OTHERS Inspecting the unit prior to installation is the responsibility of the installer or building contractor who acts on behalf of the user They are responsible for ensuring the unit is free of defect or damage Notices are placed on and in the unit and on t
9. OWNER S MANUAL Assembly Installation S amp Operating Instructions JACUZZI J DREAM II Shower System IMPORTANT SAFETY INFORMATION READ ALL INSTALLATION INSTRUCTIONS Jacuzzi Whirlpool Bath does not recommend prolonged periods of use of the steamer Prolonged use of the steam system can raise the internal human body temperature excessively and impair the body s ability to regulate its internal temperature resulting in hyperthermia Consult your physician about your safety and comfort before using the steam system limit your use of steam to 10 15 minutes until you are certain of your body s reaction A cooling shower spray can be used simultaneously with the steam to assist in regulating your body temperature Alcohol certain drugs or medications such as tranquilizers affect a person s ability to withstand high temperatures and may produce dangerous side effects Do not use alcohol or drugs when using the J Dream Il The elderly the infirm and children should not use the J Dream Il unattended Pregnant women and people with heart conditions should consult their physicians before using the steamer The wet surface of the J Dream II can be slippery Use care when entering and exiting When using the J Dream II basic safety precautions should always be followed This unitis to be connected to a Ground Fault Circ
10. TATIONS Our warranty does not cover defects damage or failure caused by the common carrier installer user or other person or resulting from without limitation any of the following careless handling lifting unit by plumbing abrading finish etc modification of any type for any reason including modification to meet local codes improper installation including installation not in accordance with instructions and specifications provided with the unit connections supplied by the installer of the equipment improper voltage supply or unauthorized electrical modification misuse incorrect operation or lack of proper routine maintenance operation of the unit without specified minimum amount of water or at inappropriate water temperature use of abrasive or improper cleaners or acts of God such as lightning floods earthquakes etc In addition THE COMPANY WILL NOT BE RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES or losses arising from any cause e g water damage to carpet ceiling loss of use etc including its own negligence damages to respecting or resulting from plated parts when chemicals are used in the unit optional equipment not manufactured by the Company supplied by Dealer installer or the Company the unit s prior usage as an operational display or defects that should have been discovered before installation This limited warranty does not include labor transportation or other costs incurred in the removal and or
11. ace will require refinishing Ask your dealer for special instructions J Dream Il Owner s Manual J Dream II Packaging 6 cartons packed together on a wooden crate Contents of cartons Wall Panels Door Frame Base Cover includes product accessory pack and owners manual Back Wall Seat Wall Equipment Seat Wall J Dream Il Owner s Manual Letters A are used in the illustrations of the assembly procedure BOLT F SELF TAPPING M6x50mm U CLIP A CLIP x 10 24 J NUT 1 4 20 LOCK NUT PAN HEAD SCREW B screw MUNN 10 24 x 3 4 K WASHER FLAT WASHER 10 PAN HEAD SCREW C WASHER FLAT WASHER 1 4 L SCREW 6 32 x 38 D NUT LOCK NUT 10 24 SIDE BRACKET FLAT HEAD SCREW E SCREW Po M4x10mm F screw itty PAMEROSOREW snacken BOLT imu HEX BOLT LAG SCREW Semen 1 4 20 x 1 5 CLAMP EXTERNAL TOOTH LOCK WASHER 1 4 WASHER 08 J Dream Il Owner s Manual Rough in IMPORTANT This is the installed position of the waste stub out when connected to the shower drain If the stub out is installed before the shower unit leave enough flex in the waste line to allow the end of the stub out to be blocked temporarily see page 10 in a position under flush to the floor surface the shower unit to slide across the floor into position without having to lift it IMPORTANT The shower drain is designed to connect to a 2 inch 50mm ABS or PVC as approv
12. e compliance Jacuzzi Whirlpool Bath P O Box 702168 Dallas TX 75370 2168 Service Support Call 800 288 4002 1997 Jacuzzi Whirlpool Bath 922000 8 13 04 Printed in the U S A 30 45 Printed on Recycled Paper 31 32 Jacuzzi Whirlpool Bath Limited Warranty Shower System Product WARRANTY COVERAGE Jacuzzi Whirlpool Bath the Company offers the following express limited warranty to the original purchaser of any Jacuzzi Whirlpool Bath Shower System product unit who purchases the product for personal or single family use user The Company will repair or replace at its option the unit or its equipment in accordance with the following terms and conditions ONE YEAR LIMITED WARRANTY ON SHOWER SYSTEM Our warranty on Shower System products is for one 1 year Our warranty covers the unit and factory installed components e g pump motor against defects in material or workmanship Warranty coverage begins on the date the unit was originally purchased by the user NINETY DAY PARTS ONLY LIMITED WARRANTY ON OPTIONS AND ACCESSORIES Our warranty on options and accessories manufactured by the Company is for ninety 90 days for parts only Our warranty covers options and accessories manufactured by the Company e g fill spout kits trim kits skirts against defects of material or workmanship Warranty coverage begins on the date the option or accessory was originally purchased by the user WARRANTY LIMI
13. ed by local codes standards waste stubout End of 2 inch 50 mm waste stubout must be located to these dimensions within 1 4 inch 6mm FINISHED WALL SURFACE WASHING MACHINE OUTLET HOSE BIBB 2 BOX 2 1 2 HOT CONNECT 8 GAUGE amp COLD 10mm2 MINIMUM SOLID WATER COPPER BOND WIRE TO SUPPLY THE HOUSE ELECTRICAL LINES PANEL OR APPROVED LOCAL GROUND AN APPROVED GROUND MAY BE AN 8 FOOT LONG GROUND ROD 3 METER LONG EARTH ROD A PLATE ELECTRODE OR OTHER ACCEPTABLE BOND CHECK YOUR LOCAL BUILDING CODE FOR REQUIREMENTS SEE PAGE 22 FOR BONDING INSTRUCTIONS This will allow ELECTRICAL OUTLET 3 WIRE 240V 20A RATING TO BE ON A GFCI PROTECTED CIRCUIT FINISHED FINISHED WALL SURFACE 42 FINISHED FLOOR MATERIAL 2 WASTE STUBOUT FINISHED MINIMUM J Dream Il Owner s Manual Locate Base to provide assembly access to all sides Remove Base from carton labeled Base Top Place Clear Top in carton to prevent damage The Clear Top will not be installed until the unit has been fully assembled and plumbed Position the J Dream base on the floor so that you have work access to all four sides of the unit during assembly Allow a minimum of 24 600 mm of access on each side of base Before starting assembly position the base pointing in the same direction as it will be in the final installation po
14. ed of clear symbols to identify the five functions STEAM JETS PULSED JETS START BUTTON START BUTTON START BUTTON Jacu WHIRLPOOL SYSTEMS CONTROL CENTER HAND HELD SHOWER CASCADE OFF BUTTON START BUTTON START BUTTON FIGURE 1 CONTROL PANEL AND DISPLAY Starting Any Function The mixer control valve must be ON for the functions of the control panel to be operational except for the steam function After the mixer valve has been set andis ON press any button to start that function The steam function can be ON with any other function Other functions can only be ON one at a time Pressing the OFF button turns all functions OFF Mixer Control To adjust the temperature turn the mixer handle as shown in Figure 2 When exiting the J Dream with all functions OFF the mixer control must be turned to the OFF position FIGURE 2 MIXER CONTROL Shower The shower button has four modes pressing once activates one shower pressing twice activates the other shower only pressing a third time activates both showers and pressing a fourth time deactivates both showers Pressing the OFF button or any other button will turn the shower mode OFF regardless if one or the other or both showers are operating Cascade This feature offers the pleasant sensation of a waterfall lapping over your shoulders and body as you are comfortably seated To start the cascade press the CASCADE button on the display Figure 1 to automatica
15. eted before final testing Room Construction Important The room where the shower unit is to be located must be constructed of materials that can withstand excessive amounts of moisture and condensation Large amounts of steam can be released into the room when the shower door is opened Providing natural or forced ventilation of the room will help maintain comfort and minimize moisture damage to the building Jacuzzi Whirlpool Bath is not responsible for damages resulting from excess moisture or water spillage Consult an architect or engineer for aid in designing your interior structure Do not install heat lamps directly above the shower unit The clear top will deform from excess heat Water Supply Required The water supply must be capable of delivering 6 gallons per minute minimum to the unit within a pressure range of 30 65 PSI 2 1 4 6 BAR Pressures in excess of 65 PSI 4 6 BAR must be reduced with a regulator in the supply line This is the amount of water and pressure required to ensure adequate performance of the J Dream Il it is not the water consumption rate NOTE DO NOT provide less than minimum flow specified Negative pressure under certain conditions could cause a health hazard by fouling of the house potable water supply Electrical Power Required See Specifications for power required Power supplied to the unit must be through a GFCI protected dedicated circuit with proper bonding and grounding The GFCI must be located i
16. ety switch tripped REMEDY Allow 2 minutes for steam to flow Replace water filter drain and flush out steamer and steam plumbing Pour six ounces of waiter into the steam delivery tube Reset high limit safety switch 2 Steam generator will fill and produce steam but will boil water away without refilling and shut itself off There is a high concentration of mineral buildup in the tank water because of continued use without draining the tank This causes faulty water fill opera tion and the high temperature safety switch will trip Replace water filter drain and flush out steamer and steam plumbing Pour six ounces of water into the steam delivery tube Reset high limit safety Switch 3 Excess water is exhausted from the steam head There is a high concentration of mineral buildup in the tank Replace water filter drain and flush out steamer and steam plumbing Pour six ounces of water into the steam delivery tube PRODUCT SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE USE INSTALLATION INSTRUCTIONS SUPPLIED WITH PRODUCT Jacuzzi Whirlpool Bath has obtained applicable code standards listings generally available on a national basis for products of this type Itis the responsibility ofthe installer owner to determine specific local code compliance prior to installation of this product Jacuzzi Whirlpool Bath makes no representation or warranty regarding and will not be responsible for any cod
17. ews K S Panel 3 Ss d s Remove SS screws to o SS swing the SS seat wall SS open Washer 4 C Seat Wall M Top View When Panel 8 is installed and put in position the seals will be as shown J Dream Il Owner s Manual Install Back Wall Caulk the bottom and sides of back wall where indicated in the illustrations below Install fasteners Now align the back wall parallel to the pan lip to center the back wall between the seat walls Pan lip Parallel I Back wall I 4 Panel 2 Panel 3 M clarity A O Nut 4 Washer 8 g asner C 9 Seat walls not b shown in this Caulk illustration for A 5 J Dream Il Owner s Manual Attach Panels 1 and 4 to Seat Walls Remove 4 bolts from seat walls to attach panels 1 and 4 Caulk along surface of seat walls Seat wall attaches to panel 1 and 4 in two places Seat wall attaches to panel 1 and 4 in three places Washer 10 C Caulk Reinstall bolts 4 and washers 4 removed from seat wall and bracket Narrow side of panel faces toward the front Panel 1
18. he shipping carton advising the installer of this responsibility In the event of a problem the unit must not be installed The Company is not responsible for failures or damage that could have been discovered repaired or avoided by proper inspection and testing prior to installation Damage occurring in transit is the responsibility of the carrier The user or installer MUST open the crates and inspect the unit for damage when it is delivered If damage is discovered it must be reported immediately to the seller and the carrier in writing and an inspection requested Failure of the carrier to respond should be reported to the seller and the carrier Your freight claims should be filed promptly thereafter Itis the responsibility of the installer building contractor or user to provide access for service The Company is not responsible for any costs relating to obtaining access for repair The user shall bear such costs and if appropriate must seek recovery from the installer Damage occurring to the unit during installation is the responsibility of the installer and or building contractor and damage occurring thereafter is the responsibility of the user Failure of any optional equipment is the sole responsibility of the equipment manufacturer Options and accessories manufactured by the Company are warranted for ninety 90 days from the original date of purchase for parts only The Distributor or Dealer is responsible for knowing local code requi
19. ide J Dream Il Owner s Manual Attach Door Frame to Angle Brackets and Base Frame Before proceeding make sure the seat walls are closed and fastened See detail B on page 15 Align door frame over tabs on base frame and pan lip Pan lip is to fit into corner posts of door frame Align holes along sides of door frame with angle brackets and mark this position of the angle brackets Remove door frame and angle bracket screws Apply the silicone caulk and reinstall the angle brackets at the marked position Insert screws and tighten Reposition the door frame and install screws through angle brackets into door frame post Then install bolts 2 through frame tabs into door frame Do not over tighten Do not silicone caulk angle brackets to door frame as they allow service access to equipment MIR fi Panel 4 17 Screw 3 Panel 1 Angle Bracket Screw 3 y E X Enclosure Post Panel 4 Angle Bracket Enclosure Post Washer 2 Base Frame Bolt 2 H C J Dream Il Owner s Manual Attach Top Frame to Door Frame Back Wall and Seat Wall Frames Press tap top frame into door frame aligning notch in door frame with corner of top of frame while aligning with corners of enclos
20. kwall From Backwall From Backwall Diconnect This Hose When Accessing Equipment on This Seat Wall From Cascade Tee Manifold mixer Power Cords from SteamPros Gur LT LT LT LT To Tee on Cold Water Line Ee Steam Line from Backwall with black insulation cover 21 J Dream Il Owner s Manual Bonding top left hand side of right hand equipment seat wall Connect a 8 guage 1 0mm minimum solid copper bond wire to the house electrical pannel or an approved local ground An approved ground may be an 8 foot long ground rod 3 meter long earth rod a plate electrode or ther acceptable bond location Check your local building code for requirements If necessary remove one screw in the plastic cover plate on top of seat wall frame and swing plate out of the way for access POWER CORD JUNCTION BOX 22 J Dream Il Owner s Manual Make sure electric power is OFF at main breaker Static test water supply hoses for leaks Plug power cord into GFCI protected wall outlet Move the assembled J Dream Il into final position Connect 2 shower drain see page 9 Adjust the levelling screws in the J Dream Il base feet and lock them in position Recheck fit of drain plumbing Secure J Dream II in position using clamps provided as shown in Figure 1 Connect showerhead hoses to wall outlets snap drain cover into place 0 Adjust the Optica mixer rotatio
21. lly start water delivery from the nozzles above the seats To stop the cascade press the CASCADE button again or OFF button or any other button 27 Starting the Hydromassage The J Dream allows you to enjoy the benefits of a real hydromassage The hydromassage is created by the combined action of 16 water jets four sets of 4 The action of each group of jets is either alternated or pulsed To start the hydromassage jets press the JETS button once Figure 1 This will activate the jets on one wall Pressing it a second time will shut OFF that wall and activate the other wall Pressing a third time activates both walls and pressing a fourth time turns the hydromassage OFF The PULSED JETS button may be pushed with either wall or both walls on Pressing this button once will increase the rate of the pulses from a default speed Pressing asecond and third time continues to increase the rate of pulsation Pressing a fourth time reverts to the default rate To stop the hydromassage in any mode press the OFF button or any other button Starting the Steam Bath Press the STEAM start button on the display Figure 1 The steam function has a 60 minute cycle after which it turns off automatically The steam bath can be turned off at any time by depressing the OFF button Do NOT operate the steam generators without the water supply ON as permanent damage to the generators will occur CD RADIO For operation of the CD radio consult the manual enclosed
22. ly connected devices such as television radio telephones stereo speakers lights or cooking devices within 5 feet of the J Dream II while it is in use Ventilation Water which drips on the floor during exit from the J Dream Il may cause a walking hazard and or structural damage unless proper waterproof building materials are used in the area surrounding the unit Take into consideration also the high room humidity which will exist due to use of the steamer Providing natural or forced ventilation of the room will help maintain comfort and minimize moisture damage to the building Jacuzzi Whirlpool Bath is not responsible for damages resulting from excess moisture or water spillage Consult an architect or engineer for aid in designing your installation Maintenance Cleaning the J Dream Il To clean your J Dream II simply use a mild nonabrasive liquid detergent or commercially prepared bathtub cleaners Do not use abrasive cleaners You can protect and restore the gloss to a dulled surface by applying a plastic polish specifically designed for use on acrylic finishes methylmethacrylate If an acrylic polish is not available an automotive paste wax will do Repairs to the surface Minor scratches which do not penetrate the color finish acrylic can be removed with 600 grit wet dry sandpaper Restore the glossy finish with an acrylic polish or a comparable automotive paste wax Major scratches or gouges which penetrate the acrylic surf
23. mpression Sleeve J Dream Il Owner s Manual Attach Seat Walls to Base J Dream Il with stereo shown Align four holes on seat wall frame over base and insert bolts and tighten nuts from underneath r4 P 2777 Non Equipment at Wall 1 Equipment Seat Wall Wf UM a y My X 77 2 bum E SS MAMMA NX A amp 2 J Dream Il Owner s Manual Attach Panel 2 to Seat Wall Frame Slide in panel feeding between frame and edge of seat wall Align to frame and fasten panel to frame Important do not caulk panel to seat wall as the seat wall is hinged and designed to swing open You may want to swing the hinged seat wall open to get better access to the installation of the screws Remove these 4 screws to swing the seat wall open Seat Wall Top View When Panel 2 is installed and put in position the seals will be as shown J Dream Il Owner s Manual Attach Panel 3 to Seat Wall Frame Slide in panel feeding between frame and edge of seat wall Align to frame and fasten panel to frame Important do not caulk panel to seat wall as the seat wall is hinged and designed to swing open You may want to swing the hinged seat wall open to get better access to the installation of the scr
24. n an area that will allow access for frequent testing GFCI Ground Fault Circuit Interrupter is also known as an ELCB Earth Leakage Circuit Breaker This device must be a type approved by electrical codes and standards to protect users from potential electrical hazards J Dream Il Owner s Manual Electrical requirements Your J Dream Il as it comes from the factory requires a GFCI protected 240 VAC 3 wire 20 AMP 50 60 Hz circuit 2 conductor with ground for single 1 phase electrical service and must be in a separate circuit having no other appliance connected in that circuit If you do not have this kind of circuit a qualified electrician should be called in to install the necessary wiring Inadequately sized wiring or locating the unit too far from the main service panel may cause a voltage drop A drop in voltage can cause the unit to malfunction and bring about permanent damage to the shower s electrical system The circuit ground wire must be provided to take advantage of the designed in safety features of the J Dream II Bond according to procedure described on page 23 Caution Without proper grounding and bonding a system malfunction may cause fatal shock Electrical precautions Lighting and electrical receptacles must be located at least 5 feet 1 5 meters from the J Dream II Lighting located between 5 feet and 10 feet 1 5 meters and 3 meters from the J Dream II must be on a circuit protected by a GFCI Do notuse electrical
25. nal between lockwashers and retighten screw Velcro 24 J Dream Il Owner s Manual Top Cover Place cover on top of unit Align notch in cover with the corresponding notch in the top metal frame J Dream Il Owner s Manual Turn On Electric Power at Main Breaker Operate Unit and Check for Leaks Attach Bottom Front Panel to Unit Take the bottom panel at an angle and insert under the bottom of the enclosure frame Rotate backwards till it is up against the brackets with the pre installed Velcro ES z DUN l SS X ZZ Enclosure ISN AA zc Base Pis oor SS Pramo x Panel j Use finishi tri terial Ls CE tris eee SS J z Between J Dream ll and i t X R A attach finisfing strips to S Z x ace panels zm o SS Screws SS E o Du S m MI S POSS Velcro i ss P LJ E Velcro Removable Face Panels Bottom Face Panel fastened with Velcroe 26 Part Il Operating Instructions CONTROL PANEL System control is provided by the electronic display located inside the shower cabin see Figure 1 The display is used to start up the five functions of the unit the shower the cascade waterfall the hydromassage all jets hydromassage pulsed jets and the steam bath The display is compos
26. nal limit stop To adjust consult the Optica instructions enclosed with this manual oc PD ERE I ee ey ae Secure J Dream II in position on floor using clamps provided on two front feet Velcro Lag bolt Floor clamp Ne i ae ee p PA Adjustable foot FIGURE 1 J Dream Il Owner s Manual Attach Front Panels to Unit Attach both left and right front panels with pre installed Velcro On the left front panel install 2 screws through the top of the panel Connect the CD radio ground wire speaker power connector and antenna wire before installing left front panel Ground wire is bolted to the seat wall frame B Screw 2 A A rema A S SG J Remove this screw TS p before operation j ENS Il SS E SS zs IA iiaii SS E S WN j SS S o I S H es D 9 Speaker and Antenna il power leads Wire S D Ground hM Rear iow et CD radio 7M Rl il B f amp P S20 X yI s EX ENT Pe Frame SS Hl H Screw 2 P gt SSS LAS Front Panel D Important attach Ze CD Radio ground Screw to be removed to permit wire here attachment of CD Radio ground wire Put ground wire termi
27. ome effective Jacuzzi Whirlpool Bath P O Drawer J Walnut Creek CA 94596 9885 vO EL 8 a E 3 o zm Uz D egos o AD QOs E 3 ms A Z D 9 oO Jacuzzi is a Federally registered trademark owned by Jacuzzi Inc 5 Alo iiS m ure Copyright 1997 Jacuzzi Whirlpool Bath K922000 8 13 04 amp 23 Leu ERECTUS ECCE ERN WAR E E RR RUE n a oS S B Pow e B gt e i EWESE JSSSZ E Pate Mc EE eS eg qe UI ence Mum R oo a daa o P 3 z z UP Sete ze Foore 2959828 9 252 a ae petal E E a 1 1 begat 3r E e c ttz Bp2oB bud Is A E m pa y o lt B 8Sa SEgSSEERS Eu3 u2888g2555999208902980889cg 3980 0028 pg35 0 8828598 2 940g 239555509gdo88502020g 42829528509 28225808 22029dg 2g 8283 oo8sz3 os S Zgz2ovooog4225252292 223 oz zo 5Do 9 lt Gag FSLQ oaao 8 Ec onc OT ed oovan gt gt a en J Zo o 2 899 SRSEESSSRES TOSS B9 gade B883Z s8 pg 330379 223902 09 g RES Ze I x gt oP s3 o2 5003 Gs 3 2 3 0 wee S ao o a ot ox D e oazo co E S 00 3z ao Pa pees 2zeRBR32j 0 o o o 3 5 99082999 T rg9eel i89 dzo9 o E398 25582232 So03z297 OOO 59 7202 S gt lea S572 zya Za o o Oa lt x Dwooo goga o Fae 3 e 2092 zggoo o FaF 8 o zg 9 uoooo 95 5 3852 a 538 3355 7C 88950 goi FDE gs ES Sl o mgoos a g 2 9g z s 28298 32 82 g92338 4 8 z o Lo A s ee ee ee a DD 8g 28 72 32388 5 353 9 48735 e 27
28. reinstallation of the original unit and or installation of a replacement unit any costs relating to obtaining access for repair or loss of use damage including loss of sales profit or business advantage of any kind under any circumstances Units in commercial use are excluded from any warranty coverage whatsoever Warranty coverage is provided in the United States of America only IMPLIED WARRANTIES Implied warranties of merchantability and fitness for a particular purpose are disclaimed altogether or to the full extent allowed by law NOTICE This warranty gives you specific legal rights and you may also have other rights which vary from state to state There are no warranties applicable to Jacuzzi Whirlpool Bath products except as expressly stated herein or as implied by applicable state and federal laws The Company will not be responsible for any statements or representations made in any form that go beyond are broader than or are inconsistent with any authorized literature or specifications furnished by the Company Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages so the above limitations and exclusions may not apply to you RETURN OF WARRANTY CARD The attached pre addressed Warranty Registration Card MUST be filled out by the purchaser within thirty 30 days from purchase and mailed to Jacuzzi Whirlpool Bath in order for this warranty to bec
29. rements and notifying the installing contractor and or user of these requirements at the time of purchase The Company is not responsible for costs to modify any product to obtain any code approval such as city county or state building codes WARRANTY SERVICE For the customer s benefit the Company maintains a list of independent service personnel to perform required warranty service repairs Such firms are not agents or representatives of the Company and cannot bind the Company by words or conduct The Company will provide the warranty service described above when the following conditions have been met the failure is ofthe nature or type covered by the warranty the user has informed an Authorized Jacuzzi Whirlpool Bath Service Agent or Warranty Service Department Representative of the nature of the problem during the warranty period conclusive evidence e g proof of purchase or installation is provided to the foregoing by the user proving that the failure occurred or was discovered within the warranty period an authorized independent service person or Company representative has been permitted to inspect the unit during regular business hours within a reasonable time after the problem was reported by the user In order to obtain warranty service consult your local telephone book for the location of the nearest Jacuzzi Whirlpool Bath Authorized Service Agent Describe the problem and the Authorized Service Agent will inspect the unit and provide the
30. sition so no unnecessary turning of the unit is required Niche where J Dream II is to be finally installed Notice Base is positioned in the same direction as it will be in the final installation position Base Floor cut out for drain P Drain Fitting x Silicone Sealant J Dream Il Owner s Manual Drain Fitting provided with unit Leave enough flexibility in the waste line to allow the end of the stub out to be blocked temporarily in a position under flush with the floor surface This will allow the shower unit to slide across the floor into position without having to lift the shower unit Studwall Temporary Wood Block Drain Compression Fitting Z a E Floor st Drain Assembly Remove the block and pull the drain assembly up to insert the stub into the drain The drain fitting is a non caulk type compression fitting drain Make certain that the locking ring is loose to allow the drain stub to insert easily inside the rubber compression sleeve If necessary lubricate the sleeve with a mild soap solution The drain stub must extend well into the rubber sleeve before the locking ring is tightened Use a screwdriver and the assembly tool provided to tighten the locking ring Screwdriver G Tighten Locking Ring L Clockwise i Assembly Tool Locking Ring Broken Line Rubber Represents Drain Stub Co
31. uit Interrupter GFCI This is also known as an Earth Leakage Circuit Breaker ELCB Check at least once a month to be sure this is operational With the unit operating push in the test button The unit should stop operating and the trip indicator should appear Restore the power push to OFF then turn ON The unit should now operate normally If the interrupter fails to operate in this manner there is a fault in the electrical system or the GFCI and you may not be protected from an electrical shock Turn off the power and have a qualified electrician check the circuit before using it again Do not use electrically connected devices such as television radio or stereo speakers lights hair dryers or telephones within 1 5 m 5 feet of the J Dream II while in use Read manufacturer s safety information with all optional equipment Note This is a professional grade product A good knowledge of construction techniques plumbing and electrical installation according to codes are required for proper installation and user satisfaction We recommend that a licensed contractor perform the installation of all Jacuzzi Whirlpool Bath products Our warranty does not cover improper installation related problems Save These Instructions for Future Use Owner s Record Date Purchased Purchased From Installed By Serial Number See page 2 for location of serial number Contents Part Assembly amp Installation
32. ure Frame snaps down into door frame and back snaps over back wall Install bolts 4 through top frame and into left and right seat wall frames Bolt 4 Washer 4 ay Frame Seat Wall Frame Nut 4 J Bracket preinstalled J Dream Il Owner s Manual Left Seat Wall Feed the four hoses and controller cable from the back wall and connect them as shown The steam hose connection uses a hose clamp while the other hoses use spring clamps that are on the hoses Also feed the CD Radio wire bundle to the back wall J Dream II with stereo only Back of Left Seat Wall From Backwall Qe oe to Cascade Tee on Equipment Seat Wall CD Radio Wire Bundle From Backwall to Valve 1 to Valve 3 Valves on Equipment Seat Wall Connect to CD Power Supply Black amp Red Wires C To Speaker on Equipment Seat Wall To Speaker CD Radio connector on Equipment Seat Wall lucc Steam line with Black Insulation Cover Hose Clamp 19 J Dream Il Owner s Manual Back Wall Use cable ties to attach the CD Radio wire bundle to the cascade hose The hoses from valves 1 and 3 and the steam hose are loosely attached to their mounting brackets to allow the slack when connecting them and when the hinged seat wall is swung open like a door to
Download Pdf Manuals
Related Search