Jacuzzi Espree Series User's Manual
Contents
1. Espree Series INSTALLATION AND OPERATING INSTRUCTIONS Installer Leave this manual for homeowner Homeowner Read this manual and keep for future reference 2003 Jacuzzi Whirlpool U961000F 12 04 IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS 1 CAUTION TEST THE GROUND FAULT CIRCUIT INTERRUPTER PROTECTING THIS APPLIANCE PERIODI CALLY IN ACCORDANCE WITH MANUFACTURER S INSTRUCTIONS WARNING RISK OF ACCIDENTAL INJURY OR DROWNING CHILDREN SHOULD NOT USE HYDROMAS SAGE BATHTUB WITHOUT ADULT SUPERVISION WARNING TO AVOID INJURY EXERCISE CAUTION WHEN ENTERING OR EXITING THE HYDROMAS SAGE BATHTUB WARNING RISK OF ACCIDENTAL INJURY OR DROWNING DO NOT USE HYDROMASSAGE BATHTUB UNLESS ALL SUCTION GUARDS ARE INSTALLED TO PREVENT BODY AND HAIR ENTRAPMENT WARNING KEEP BODY AND HAIR A MINIMUM OF 6 AWAY FROM SUCTION FITTING AT ALL TIMES WHEN THE WHIRLPOOL SYSTEM IS OPERATING HAIR LONGER THAN SHOULDER LENGTH SHOULD BE SECURED CLOSE TO THE HEAD WARNING NEVER DROP OR INSERT ANY OBJECT INTO ANY OPENING WARNING RISK OF ELECTRICAL SHOCK DO NOT PERMIT ELECTRICAL APPLIANCES SUCH AS HAIR DRYER LAMP TELEPHONE RADIO OR TELEVISION WITHIN 60 1 5 M OF THIS HYDROMASSAGE BATHTUB WARNING RISK OF ACCIDENTAL INJURY OR DROWNING DO NOT USE DRUGS OR ALCOHOL BEFORE OR DURING THE USE OF HYDROMASSAGE BATHTUB EQUIPPED WITH A HEATER TO AVOID UNCON SCIOUSNESS AND POSSI2. 52 5558 52255 52 08 583598 595025235 28 o 4244 5 OR 27 9 o 23 256 woo lt L 1 842 5896 588528 B 5222 d 88 3808 Z780 56 THE 5 2 cO cO 5 9 E oL see Eo lt 2942 2 35 gt 8 82 38782 si2238 8 75 gt 0 0 5 8 4 m B g 8 08 2 35827 225 29 5886858 gt o lt lt Ome x S5 9022 c D O gt c lt 5200 5 20 S BOS S 5 go 9999 55 253238 8988 80 5 9382 S 22 629 B N o 98552 2RGQG o 29 99 9 D m o o o mem 5 O T D c BF 922 o gt e z gt 5 29 7 oO s D g 5585 5 eTel el 2 ara Eu m bo 3 Sosg 22 o 2 o g o S 800 S 9 55 D A 2 2 a lt 35 gt rs D ol S lt 2 Seco 50 o9o Q7 25 lt 589 2 g P o 2 so TO 3 3 D Q A m lt B 80 Sv ogG g2 9 9 5 2925 9 N p E lt oSOdoo 3 0 gt m RR lt oo FFG as NS 9o9 2 TI By 8 S Uf N 929 c GC 5 a S D o9 T O 9 so lt cO u 225 c so UD os oc o9 5 a 0 e e lt ud o Q So D o Q n
3. Jacuzzi Whirlpool Bath U961000F 12 04 REPAIR PARTS lt POSITION PANEL BUTTON AIR ACTUATOR 8246XXX KNOB 8267XXX 2 BEZEL 8247XXX GRAPHIC RING AIR 2 8263XXX GRAPHIC RING ON OFF 8262XXX 3 POSITION PANEL 9224XXX BELLOWS C377000 AIR CONTROL ASSEMBLY U767000 2 SCREWS 10 9724000 CUP C841000 17 Jacuzzi Whirlpool Bath U961000F 12 04 REPAIR PARTS rapid heat RAPIDHEAT REPAIR HEATER DISCHARGESIDE U394000 SHOWN UNION GASKETS 2 Y671000 UNIONS 2 Y670000 SUCTIONSIDE S749000 UNION GASKETS 2 G947000 UNIONS 2 T180000 NOTE Suction heater components and Discharge heater components are not interchangable HEATER BLANK DISCHARGESIDE BF67000 UNION GASKETS 2 Y671000 UNIONS 2 Y670000 MOTOR PUMP ASSEMBLY 7 0A 115V 60Hz Y660000 SUCTIONSIDE BF68000 UNION GASKETS 2 G947000 UNIONS 2 T180000 UNION REPAIR KIT 9250000 O RING 9231000 ADAPTER UNION 9234000 NUT UNION 9233000 SWITCH AIR ACTUATED 7396000 STRAIN RELIEF AIR SWITCH N186000 PRODUCT SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE USE INSTALLATION INSTRUCTIONS SUPPLIED WITH PRODUCT Jacuzzi Whirlpool Bath has obtained applicable code standards listings generally available on a national basis for products of this type It is the responsibility of the installer owner to determine specific local code compliance prior to installation of the product Jacuzzi Whirl
4. o gt lt gt o9 C
5. 936 Ib 425 kg 67 16 54 ft 326 kg sq m 893 Ib 406 kg 51 Ib sq ft 249 kg sq m 911 Ib 414 kg 51 Ib sq ft 249 kg sq m 886 Ib 403 kg 42 b sq ft 205 kg sq m AVERAGE OPERATING 58 Min U S gal 219 liters 66 Max U S gal 250 liters 50 Min U S gal 189 liters 58 Max U S gal 220 liters 50 Min U S gal 189 liters 58 Max U S gal 220 liters 50 Min U S gal 189 liters 61 Max U S gal 231 liters 60 Min U S gal 227 liters 68 Max U S gal 257 liters 60 Min U S gal 227 liters 68 Max U S gal 257 liters 64 Min U S gal 242 liters 73 Max U S gal 276 liters 74 Min U S gal 280 liters 89 Max U S gal 336 liters HEATER READY PRODUCT SKIRT amp FOR FIELD WEIGHT MOUNTING INSTALLATION 128 Ib Not Yes 58 kg Available 8750000 HEATER KIT 102 Ib Not 46 kg Available 113 Ib Integral Yes 51 kg 5750000 HEATER KIT 117 Ib Not 53 kg Available 127 Ib 58 kg 127 Ib Integral Yes 57 kg 5750000 HEATER KIT 120 Ib Not Yes 55 kg Yes 8750000 HEATER KIT Yes U395000 HEATER KIT Not Available Yes 8750000 HEATER KIT Available U395000 HEATER KIT 120 Ib 55 kg Not Yes Available U395000 HEATER KIT Jacuzzi Whirlpool U961000F 12 04 SPECIFICATIONS CORNER BATHS FRONT VIEW SIDE VIEW LI B DRAIN OVERFLOW FRONT VIEW SIDE VIEW ESPREE 6060 WITH SKIRT SPECIFICATIONS C
6. Your freight claims should be filed promptly thereafter It is the responsibility of the installer building contractor or user to provide access for service The Company is not responsible for any costs relating to obtaining access for repair The user shall bear such costs and if appropriate must seek recovery from the installer Damage occurring to the unit during installation is the responsibility of the installer and or building contractor and damage occurring thereafter is the responsibility of the user Failure of any optional equipment is the sole responsibility of the equipment manufacturer Options and accessories manufactured by the Company are warranted for ninety 90 days from the original date of purchase for parts only The Distributor or Dealer is responsible for knowing local code requirements and notifying the installing contractor and or user of these requirements at the time of purchase The Company is not responsible for costs to modify any product to obtain any code approval such as city county or state building codes in U S A WARRANTY SERVICE Forthe customer s benefit the Company maintains alist of independent service personnel to perform required warranty service repairs Such firms are not agents representatives ofthe Company and cannotbind the Company by words or conduct The Company will provide the warranty service described above when the following conditions have been met the failure is of the nature orty
7. an optional Jacuzzi Whirlpool Bath wall mounted timer set it for the amount of time you wish the whirlpool to operate Note when you desire less than 10 minutes of whirlpool action it is necessary to turn the timer knob clockwise past the number 10 and then back to the desired amount If the whirlpool action does not begin when the timer is correctly set it Is necessary to push the Magic Touch switch button CONTROL KNOBS 2 TOUCH SWITCH DEPRESS CENTER ON OFF Jacuzzi Whirlpool U961000F 12 04 OPERATION RapidHeat Operation Once the heater is installed and the whirlpool pump is operating the heating function is totally automatic The heater will help maintain the temperature of the water in the bath Vacuum Switch The heater is equipped with a preset vacuum switch which will not allow the heater to turn ON if the pump is not running with water flowing through the whirlpool system High Limit Switch The heater includes an exclusive High Limit switch This safety circuit will not false trip from hot tap water It will only turn off the heater if the thermostat fails To reset press the button If the high limit trips frequently contact your dealer Heater On Indicator The light will be illuminated any time the heater is operating HIGH LIMIT RESET HEATER ON HEATER ON P OVER HEAT PROTECTIO PUSH TO RESET rapid heat Controlling Whirlpool Action The whirlpool action in
8. bath flange and studs The rim of the bath is not designed to support weight If finish material is to overlap or contact the bath the added weight must be fully self supporting The protective film liner inside the bath is used to prevent damage to the finish from shoes tools etc during installation Before installation remove liner to inspect for any defects reapply and do not remove until final cleanup Important If a skirt is to be used it must be installed at the time of unit installation refer to skirt installation instructions Install optional trim parts when all installation has been completed TYPICAL INSTALLATIONS MORTAR ADHESIVE TILE FINISHING MATERIAL MORTAR CEMENT BOARD BATH RIM SUB FLOOR OR SILICONE FLASHING SEALANT 1 X 4 NOT FOR SUPPORT 1 X 4 NOT FOR SUPPORT FOR SUPPORT FLUSH TO WALL SEMI SUNKEN OPTIONAL TILE FLANGE KIT TYPICAL FLANGE MOUNTING DETAIL TILE ADHESIVE ATTACH WITH SCREWS PROVIDED SHIM IF NECESSARY TO FILL GAPS STUD STUD AND FLANGE FLANGE Jacuzzi Whirlpool U961000F 12 04 INSTALLATION Service Access For partially or fully sunken installations allow for access to service connections lt is the installer s re sponsibility to provide sufficient service access The recommended minimum dimensions allowable for ser vice to the bath are shown in the Service Access illus tration Provide adequate area around
9. fitting CAUTION Keep hair a minimum of 6 inches away from the suction fitting at all times when the whirl pool system is operating Hair longer than shoul der length should be secured close to the head or a bathing cap should be worn Do not operate the whirlpool system with the suction cover removed It is a safety device and must always be in place on the suction fitting to minimize the potential hazard of hair and body entrapment SUCTION COVER STRAINER ASSEMBLY COVER STRAINER SUCTION FITTING GASKET LIGHT BULB REPLACEMENT LOCKING NUT LIGHT BULB BULB RECEPTACLE LIGHT BEZEL BATH SHELL f 2 Due Jacuzzi Whirlpool Bath U961000F 12 04 General Whirlpool Bath Troubleshooting Guide PROBLEM Pump Motor does not start Pump Motor operates but no fully adjustable jets are functioning Pump Motor operates but air is not injected into water Pump motor does not shutoff Water leakage from pump unions Pump motor shuts off by itself or with wall timer before set time elapses PROBABLE CAUSES No power to pump motor Pump motor not plugged in Magic Touch switch air tube not connected to switch or to air switch on pump motor Pump motor faulty Jets are closed Suction cover may be clogged Air entrapment Air valves closed Magic Touch switch air tube not connected to switch or to air switch on pump motor If a wall timer is used
10. purged at least twice a month For your convenience we have developed a plumbing system cleaner Systems Clean specifically for whirlpool baths For availability call 1 800 288 4002 e Use this unit only for its intended purpose as described in this manual Do not use attachments not recom mended by the manufacturer e This unit must be connected only to a supply circuit that is protected by a ground fault circuit interrupter GFCI Such a GFCI should be provided by the installer and should be tested on a routine basis To test the GFCI push the test button The GFCI should interrupt power Push the reset button Power should be restored If the GFCI fails to operate in this manner there is a be current flowing indicating a possibility of an electric shock Do not use this unit Disconnect the unit and have the problem corrected by a qualified electrician before using e A pressure wire connector is provided on the exterior of the motor to permit connection of an No 8 AWG 8 4 mm solid copper bonding conductor between this unit and all other electric equipment and exposed metal in the vicinity as needed to comply with local requirements e This unit should be installed by a licensed electrician and grounded e For built in and drop in units install to permit access for servicing Note This is a professional grade product A knowledge of construction techniques plumbing and electri cal installation according to codes are required for
11. the timer is defective Overtightened O ring may be pinched or improperly seated under tightened Motor thermal protection has deacti vated pump motor due to overheat ing Supply voltage low GFCI tripped Inadequate supply wiring REMEDY Reset GFCI Insert plug fully into outlet Reconnect tube to Magic Touch switch or to air switch pump motor Replace pump motor assembly Open jets by rotate counterclockwise With motor turned off remove safety cover and remove any debris Replace suction cover before operating Ensure that water level is at least 2 above the highest jet Open air control valves Reconnect tube to Magic Touch switch or to air switch pump motor Replace timer Untighten unions check and reseat O ring If O ring has been pinched out of shape replace refer to Service Support number below When tightening union nuts hand tighten only Let motor cool thermal protection will reset Check for proper ventilation Check supply voltage Reset GFCI If it continues to trip do not use this unit Disconnect the unit and have the problem corrected by a licensed electrician before using Consult a licensed electrician to correct wiring to unit Note If unit is within the warranty period contact Jacuzzi Whirlpool Bath Service Support at 866 905 2289 with bath s serial number before work is started The Serial Number is located on the Specification Serial Number Plate See p
12. BLE DROWNING WARNING RISK OF FETAL INJURY PREGNANT OR POSSIBLY PREGNANT WOMEN SHOULD CONSULT A PHYSICIAN BEFORE USING A HYDROMASSAGE BATHTUB EQUIPPED WITH A HEATER WARNING RISK OF HYPERTHERMIA AND POSSIBLE DROWNING DO NOT USE A HYDROMASSAGE BATHTUB EQUIPPED WITH A HEATER IMMEDIATELY FOLLOWING STRENUOUS EXERCISE WARNING RISK OF HYPERTHERMIA AND POSSIBLE DROWNING WATER TEMPERATURE IN EXCESS OF 104 F 40 C MAY BE INJURIOUS TO YOUR HEALTH CHECK AND ADJUST WATER TEMPERATURE BEFORE USE WARNING RISK OF HYPERTHERMIA PEOPLE USING MEDICATIONS AND OR HAVING AN ADVERSE MEDICAL HISTORY SHOULD CONSULT A PHYSICIAN BEFORE USING A HYRDOMASSAGE BATHTUB EQUIPPED WITH A HEATER AN EQUIPMENT GROUNDING TERMINAL IS PROVIDED IN THE FIELD WIRING COMPARTMENT TO REDUCE THE RISK OF ELECTRICAL SHOCK THIS TERMINAL MUST BE CONNECTED TO THE GROUNDING MEANS PROVIDED IN THE ELECTRICAL SUPPLY PANEL WITH A CONNECTOR EQUIVALENT IN SIZE TO THE CIRCUIT CONNECTORS SUPPLYING THIS EQUIPMENT PRECAUTIONS e Do not operate the whirlpool system unless the bath is filled with water to at least 2 above the highest jet e Never drop or insert any object into any opening e Do not use oil based bath additives in your whirlpool bath e When cleaning your bath do not use abrasive substances which will damage the bath s surface e To prevent discoloration of the acrylic finish do not fill the bath with water in excess of 140 F 60 C e The whirlpool system should be
13. HS WITHOUT INTEGRAL SKIRT BATHS WITH INTEGRAL SKIRT SPECIFICATIONS Rectangular 542 607 1524 mm L 42 1067 mm W BACK MASSAGE 20 508 mm H ESPREE 6032 1524 mm L 813 mm W 559 mm H ESPREE 6032 WITH INTEGRAL ESPREE 6036 ESPREE 6042 ESPREE 6042 WITH INTEGRAL 1524 mm L 813 W 559 mm H 1524 mm L 1067 mm W 508 mm H 1524 mm L 1067 mm W 508 mm H ESPREE 7236 1829 mm L 914 W 508 mm H ESPREE 7242 72 1829 mm L 42 1067 mm W 20 508 H DRAIN OVERFLOW DIMENSIONS 16 7 8 15 5 8 429 mm A 397 mm B 18 1 16 10 1 4 459 mm A 273 mm B 16 7 8 10 13 16 275 mm B 429 mm A 397 mm B 429 mm A 397 mm B 16 7 8 10 13 16 429 mm A 275 mm B 70 X 40 Add 1 4 to this dimension when roughing in for 3 wall niche NOTE The overall dimensions are nominal with a tolerance of 0 and 1 4 FOR ALL UNITS Electrical Service Requirements All require a dedicated GFCI protected separate circuit RapidHeat 115 VAC 15 AMP 60 Hz dedicated GFCI protected separate circuit Motor Pump 115 VAC 15 Amp 60 Hz dedicated GFCI protected separate circuit 115VAC 20AMP 60Hz 115VAC 20AMP 60Hz 936 Ib 425 kg 54 16 54 ft 263 kg sq 357 kg 5916 54 ft 288 kg sq m 785 Ib 357 kg 5916 54 ft 288 kg sq m 825 Ib 375 kg 55 Ib sq ft 268 kg sq m
14. IR PARTS NOTE When a part number has 3 Xs substitute the appropriate color code for the Xs 940 White 914 Almond 969 Oyster BMH JET 1 POSITION AIR CONTROL RETAINER NOZZLE 8412XXX NOZZLE BHM 8413XXX O RING 8488000 INTERNAL O RING SEAT 8487XXX KNOB 8267XXX JET BODY 8411XXX GRAPHIC RING AIR 8263000 LOCK NUT 8415000 SCREWS 2 7514000 PANEL 1 POSITION D851XXX AIR CONTROL ASSEMBLY U767000 SCREWS 4 9724000 14 Jacuzzi Whirlpool Bath U961000F 12 04 REPAIR PARTS 2 POSITION CONTROLLER AIR amp PUMP MOTOR ON OFF BEZEL 8247XXX KNOB 8267XXX BUTTON AIR ACTUATOR 8246XXX MOTOR PUMP ON OFF GRAPHIC RING AIR 8263000 GRAPHIC RING ON OFF 8262XXX PANEL 2 POSITION 8241XXX BELLOWS C377000 AIR CONTROL ASSEMBLY U767000 CUP C841000 SCREWS 8 9724000 15 Jacuzzi Whirlpool Bath U961000F 12 04 REPAIR PARTS SUCTION HTC JET ASSEMBLY HTC ASSEMBLY B785XXX Wt ters p a aH 22 SCREWS 3 9356000 CLAMPING RING 788 SCREW 10 24 2 3959000 SWIVEL HTC B786XXX SUCTION COVER GASKET ASSEMBLY 6651XXX GASKET 1840000 SUCTION FITTING 1958000 HTC BODY A320XXX RING BACK UP SUCTION 2136000 BACKUP RING 1836000 LOCKNUT 1835000 LOCKNUT 1643000 Jet Body BG15000 Stop Part of Jet Body Fitting BG00XXX Nozzle Adjustable Handle BMO1XXX 16
15. age 13 Jacuzzi Whirlpool Bath U961000F 12 04 12 Authorized Service If you need a referral for a service company near you or need assistance with operation or maintenance related questions please call our Service Support Department at 1 866 905 2289 For service agent listing visit our web site at http www jacuzzi com To find the service agent listings click on For The Trade Then click on Electrical Mechanical Service Agents Depending on the problem click on Electrical Mechanical Repairs or Finish Surface or Shell Related Problems When requesting service or technical assistance please have available both the model and serial number of your unit This information can be obtained from the product registration card provided with your unit If the card has been misplaced this information can be obtained from the specification serial number label on the unit itself for location of specification serial number label see below BATH PRODUCTS Whirlpool baths The label is located on the wall of the bath near the pump motor Non jetted baths The label is located next to the overflow SPECIFICATION SERIAL NUMBER PLATE MODEL XXXXXXX NAME XXXXX COLOR XXXXX MFG XXXXX SER 4 XXXXXX YOU WILL FIND YOUR SERIAL NUMBER HERE THIS PRODUCT MEETS OR EXCEED THE FOLLOWING STANDARDS MADE IN BATH amp SPA ANSI Z124 1 SHOWER BASES ANSI Z124 2 13 Jacuzzi Whirlpool U961000F 12 04 REPA
16. ction rotate the control knobs fully counterclockwise to the largest circles For fewer air bubbles decrease the amount of air induction by rotat ing the control knob clockwise When the knobs are turned to the smallest circles only water is being circulated JETS DIRECTIONALLY ADJUSTABLE FULLY ADJUSTABLE AIR INDUCTION CONTROLS TURN CLOCKWISE TO REDUCE AIR FLOW TURN COUNTER CLOCKWISE TO INCREASE AIR FLOW MAINTENANCE Cleaning the Bath To clean your bath simply use a mild nonabrasive liquid detergent solution You can protect and restore the gloss to a dulled acrylic surface by applying Meguiar s 10 Mirror Glaze a product specifically de signed for use on acrylic finishes If Meguiar s is not available an acrylic polish of equal quality or automo tive paste wax is acceptable Never use abrasive household cleaners on any Jacuzzi Whirlpool Bath product Repairs to the Surface Minor scratches which do not penetrate the color fin ish can be removed by lightly sanding with 600 grit wet dry sandpaper Restore the gloss using Meguiar s Mir ror Glaze or automotive paste wax Major scratches and gouges which penetrate the acrylic surface will require refinishing Ask your Jacuzzi Whirlpool Bath dealer for special instructions Purging the Whirlpool System NOTE THE WHIRLPOOL SYSTEM SHOULD BE PURGED AT LEAST TWICE A MONTH To remove accumulations of bath residue from the whirlpool system it is recommende
17. d Bronze 845 Oil Rubbed Bronze Jacuzzi Whirlpool U961000F 12 04 ROUGH IN Note Unless otherwise specified units are produced with left or right hand versions P 60 Left hand shown ESPREE 6042 BM 6 60 10 13 16 Left hand only ESPREE 6032 amp 60 gt 10 13 16 Left hand shown ESPREE 6032 WITH SKIRT W M J Left hand only as shown ESPREE 6036 15 5 8 Left hand only as shown ESPREE 6042 60 3 k Left hand shown ESPREE 6032 WITH SKIRT 15 5 8 Left hand only as shown ESPREE 7236 15 5 8 Left hand only as shown ESPREE 7242 Note 1 The overall dimensions are nominal with a tolerance of 0 and 1 4 2 Add 1 4 to this dimension when roughing in for 3 wall niche 3 Measurements inside each unit represent cutout in floor to allow for drain overflow 4 All measurements are in inches To convert to millimeters multiply inches by 25 4 Jacuzzi Whirlpool U961000F 12 04 ROUGH IN 12 1 2 i a Junction Box Right hand shown Left hand is a mirror image Right hand only as shown ESPREE 6060 WITHOUT SKIRT ESPREE 6060 WITH INTEGRAL SKIRT Note 1 The overall dimensions are nominal with a tolerance of 0 and 1 4 1 Measurements inside each unit represent cutout in floor to allow for drain over
18. d that a whirlpool bath be purged at least twice a month For best results however we recommend that you purge your whirlpool bath after each use using our exclusive two part plum bing system cleaner made specifically for whirlpool baths Systems Clean is available through an autho rized Jacuzzi Whirlpool Bath Distributor or by calling us direct at 1 800 288 4002 Instructions for use Imme diately after bathing and exiting the whirlpool bath leave the bath water in the tub and add hot water if necessary so the water is at least 2 above the highest jet Turn on the unit without the aerator Pour the contents of the Systems Clean Packet 1 taking care not to get the material on yourself into the bath near the intake for the circulation pump Repeat same process with Systems Clean Packet 2 It is important to use Packet 1 before Packet 2 to avoid a strong odor Run the bath for 5 to 10 minutes Drain completely and rinse any residue If you have followed the standard purging instructions above and still have an excess accumulation of bath residue and desire an alternative cleaning mechanism werecommend SUPER SYSTEMS CLEAN PLUS manu factured by Stearns Packaging to rectify this condition This may be obtained by contacting us at 800 288 4002 Itis recommended that you follow the instructions provided by the manufacturer with the product Re peated use may be necessary SUPER SYSTEMS CLEAN PLUS does not replace the necessity to reg
19. ed between soldering work and bath unit to prevent damage to the bath Clean Up After Installation To avoid dulling and scratching the surface of the bath never use abrasive cleaners A mild liquid detergent and warm water will clean soiled surfaces Remove spilled plaster with a wood or plastic edge Metal tools will scratch the surface Spots left by plas ter or grout can be removed if lightly rubbed with deter gent on a damp cloth or sponge Paint tar or other difficult stains can be removed with paint thinner turpentine or isopropyl alcohol rubbing alcohol Minor scratches which do not penetrate the color fin ish can be removed by lightly sanding with 600 grit wet dry sandpaper You can restore the glossy finish to the acrylic surface of the bath with a special compound Meguiar s 10 Mirror Glaze If that is not available use automotive rubbing compound followed by an applica tion of automotive paste wax Major scratches and gouges which penetrate the acrylic surface will require refinishing Ask your Jacuzzi Whirlpool Bath dealer for special instructions OPERATION All baths manufactured by Jacuzzi Whirlpool Bath are designed for fill and drain which means the bath should be drained after each use and filled with fresh water by the next bather This is a health precaution as these baths are not designed to hold water continuously like pools or spas If you want a unit designed to continu ously hold water see yo
20. flow 2 All measurements are in inches To convert to millimeters multiply inches by 25 4 6060 CUTOUT 6032 CUTOUT 30 1 2 4 2 0 58 ESPREE 6032 DROP IN CUTOUT ESPREE 6060 WITHOUT SKIRT Jacuzzi Whirlpool U961000F 12 04 INSTALLATION Framing and Support The drain overflow of the bath extends below the bottom of the bath Note that this requires a cutout in the floor The floor structure beneath the bath must be able to support a total weight of bath water and bather Refer to the table under total weight for your model The unit must be supported from the bottom of the bath and not from the bath rim or tile flange If the subfloor is level no other preparation is necessary You can proceed to install the bath If the subfloor is not level you MUST level the entire surface prior to installing the bath The use of materials that shim or provide a level installation are allowed provided the method used will insure a level bath that is supported from the bottom Materials that may be used are a floor leveling compound mortar plaster or minimal expansion structural foam having a density of a minimum of 5 lbs cubic ft however the bath must remain level in order for it to drain properly and the foam feet must make full contact with the leveling material Both sides of a joint or splice of subfloor should be level to each other When attaching baths with flanges to stud wall use shims to fill any gaps between the
21. llassume the remaining warranty period of the part s replaced The Company s warranty obligation shall be discharged upon tender of replacementor repair The customer s refusal to accept the tender terminates the Company s warranty obligation q 2003 Jacuzzi Whirlpool Bath U961000F 12 04 gt o 3 isz 2422 2 lt v x U 458 D g lt lt o 2 m r cO o AB Qo 4 gt 5 UNES mi I 2523 ee ET mm T mto MO mt mm attt dtm Q O o glo gt 5525 5 5 a 1 5 o9 o cog Q Ao 21 gt 03259 pmi r 89595 55525 885552512 5 24920 4 009 890290222 929 29522528 5 4222 25 5 ws Se OCP 5 2 50 935 5 lt os5 7 oooOonaopgSgSoog 9mmo o0520529 mzu oeo9 25290200 02 2009090 5 gt Z 0 n aq A 3 J s co mrooooog cA gt O o x o o lt Geog Ilk oona oO D Q p AEN DTL S oS coooNM 00258 lt a oU S050 sel odee DZ 22555 55 922505 E O Sexo z DARKO C O co U lt o e 2 353 b o
22. manufactured by the Company is for ninety 90 days for parts only Our warranty covers options and accessories manufactured by the Company fill spout kits trim kits skirts against defects of material orworkmanship Warranty coverage begins on the datethe option or accessory was originally purchased by the user WARRANTY LIMITATIONS Our limited warranty does not cover defects damage or failure caused by the common carrier installer user or other person or resulting from without limitation any of the following careless handling lifting unit by plumbing abrading finish etc including its own negligence modification of any type for any reason including modificationto meetlocal codes improper installation including installation notin accordance with instructions and specifications provided with the unit connections supplied by the installer of the equipment improper voltage supply or unauthorized electrical modification misuse incorrect operation orlackof proper routine maintenance operation ofthe unit without specified minimum amountof wateror at inappropriate watertemperature use of abrasive or improper cleaners or acts of God such aslightning floods earthquakes etc In addition THE COMPANY WILL NOT BE RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES or losses arising from any cause e g water damage to carpet ceiling loss of use etc including its own negligence damages to respecting or resulting from pla
23. orner HEATER READY DRAIN OVERFLOW TOTAL WEIGHT OPERATING PRODUCT SKIRT amp FOR FIELD DIMENSIONS DIMENSIONS CUTOUT FLOOR LOADING GALLONAGE WEIGHT MOUNTING INSTALLATION ESPREE 6060 n 18 1 2 470 mm 888 Ib 68 Min U S gal 122 Ib Not Available Factory Installed 404 k g 257 liters 55 S750000 HEATER KIT 12 1 4 311 mm 9 9 89 Max U S gal s Ib sq ft 336 lit 176 kg sq m iters ESPREE 6060 1524 mm L 18 1 2 470 mm A 888 Ib 68 Min U S gal 12216 Integral Factory Installed WITH INTEGRAL 60 1524 12 1 4 311 mm B 404 k g 257 liters 55 kg U395000 HEATER KIT SKIRT 959 mm 36 Ib sq ft 89 Max U S gal 176 kg sq m 336 liters NOTE The overall dimensions are nominal with a tolerance of 0 and 1 4 FOR ALL UNITS Electrical Service Requirements All require a dedicated GFCI protected separate circuit RapidHeat 115 VAC 15 AMP 60 Hz dedicated GFCI protected separate circuit Motor Pump 115 VAC 15 Amp 60 Hz dedicated GFCI protected separate circuit OPTIONS FOR ALL UNITS Rotary Drain Overflow Lamp Package 7701XXX Jet Trim Kit X163XXX Kit 8730 RapidHeat In Line Heater 959 White 805 Platinum 805 Platinum Suction Side 5750000 958 Almond 815 Satin Nickel 815 Satin Nickel Discharge Side U395000 969 Oyster 826 Brushed Nickel 826 Brushed Nickel 827 Chrome 827 Chrome 829 PVD Brass 829 PVD Brass 898 Brushed Chrome 898 Brushed Chrome 845 Oil Rubbe
24. p of skirt opening and tilt up until velcro tabs make contact ACCESS PANEL SKIRT x ACCESS PANEL INSTALLATION Electrical Connections A separate circuit which must be protected by a Ground Fault Circuit Interrupter GFCI is required Install a duplex outlet to the studwall underneath the bathtub at least 4 inches above the floor The duplex outlet is not provided Because these units are manu factured with a safe convenient Magic Touch whirlpool ON OFF switch on the bath itself no remote switch or timer is necessary If an optional timer is desired one is available from Jacuzzi Whirlpool Bath for 115 VAC operation DANGER RISK OF ELECTRIC SHOCK Connect only to a circuit protected by a Ground Fault Circuit Interrupter Zi CAUTION Operating the motor pump without enough water in the bath can cause leaking and per manent damage to the pump Before power is ap plied to the installation make sure the switch is in the OFF position to avoid pump damage ELECTRICAL CONNECTION FOR SIDE END DRAIN BATHS 3 PRONG DUPLEX ELECTRICAL CONNECTION FOR MOTOR PUMP ON DRAIN SIDE 3 PRONG PLUG DUPLEX RECEPT 4 MIN OR IN ACCORDANCE WITH LOCAL BUILDING OR ELECTRICAL CODES PROVIDED Electrical Connection 6060 With Heater On the 6060 with integral skirt one junction box has been provided for the pump motor and one for the heater To access remove skirt access
25. panel See top view for location A separate GFCI protected outlet not provided is re quired for pump motor and is to be installed in the junc tion box The junction box is to be hard wired The motor is bonded to the junction box at the factory Install a separate 120 VAC 15 AMP dedicated circuit with GFCI protection With a 8 solid copper wire bond the heater to the house electrical panel or approved lo cal bond A bonding lug is provided on the heater At initial start up and before each use thereafter with power ON push the GFCI test button The reset button should pop out Push this button in to reset If the inter rupter fails to operate in this manner there is a ground current flowing or a device malfunction indicating the possibility of electrical shock Turn off power and do not use the bath until the source of the problem has been identified and corrected 60x60 WITH INTEGRAL SKIRT MOTOR JUNCTION BOX POWER CORD TO MOTOR 60x60 WITH INTEGRAL SKIRT RAPIDHEAT JUNCTION BOX BONDING TO RAPIDHEAT POWER CORD TO RAPIDHEAT Jacuzzi Whirlpool Bath U961000F 12 04 INSTALLATION Drain Information Adrain overflow assembly sold separately must be Installed on the bath water tested and connected to the sanitary system of the house After opening the carton inspect for damage and verify that the kit is of the proper finish In the Jacuzzi Whirlpool Bath drain overflow kit note that the waste flange straine
26. pe covered by the warranty the user has informed an Authorized Jacuzzi Whirlpool Bath Service Agentor Warranty Service Department Representative ofthe nature ofthe problem during the warranty period conclusive evidence e g proof of purchase or installation is providedto the foregoing by the user proving thatthe failure occurred or was discovered within the warranty period an authorizedindependentservice person or Company representative has been permitted to inspectthe unitduring regular business hours within a reasonable time afterthe problem was reported by the user Inorderto obtain warranty service consult your local telephone book for the location ofthe nearest Jacuzzi Whirlpool Bath Authorized Service Agent Describe the problem and the Authorized Service Agent will inspectthe unit and provide the required warranty service If you are unable to contact a Jacuzzi Whirlpool Bath Authorized Service Agent call or write Jacuzzi Whirlpool Bath Warranty Service Department P O Box 702168 Dallas TX 75370 2168 Call 1 866 905 2289 Toobtain warranty replacementforfactory installed components for Company supplied options and accessories manufactured and supplied by the Company callor write the above Provide a description of the problem and proof of purchase You will be instructed howto obtain replacements and whereto return at your expense the failed component s option s or accessory ies All replacementparts equipment and repairs sha
27. pool Bath makes no representation or warranty regarding and will not be responsible for any code compliance JACUZZI WHIRLPOOL BATH P O Box 702168 Dallas TX 75370 2168 Service Support 866 905 2289 02003 Jacuzzi Whirlpool U961000F 12 04 WS Printed on Recycled Paper Printed in the U S A 18 Jacuzzi Whirlpool Bath U961000F 12 04 Jacuzzi Whirlpool Bath Limited Warranty Espree Series Bath Product WARRANTY COVERAQE Jacuzzi Whirlpool Bath the Company offers the following express limited warranty to the original purchaser of any Jacuzzi Whirlpool Bath Espree Series Bath Product unit who purchases the product for personal or single family use user The Company will repair or replace at its option the unit or its equipment in accordance with the following terms and conditions ONE YEAR LIMITED WARRANTY ON BATHS Our limited warranty on Espree Series Bath products is for one 1 year Our warranty covers the unit and factory installed components against defects material or workmanship Warranty coverage begins on the date the unit was originally purchased by the user FIVE YEAR PARTS ONLY LIMITED WARRANTY ON PUMP AND MOTOR Our limited warranty onthe pump and motoris for five 5 years for parts only Warranty coverage begins on the date the unit was originally purchased by the user NINETY DAY PARTS ONLY LIMITED WARRANTY ON OPTIONS AND ACCESSORIES Our limited warranty on options and accessories
28. proper installation and user satisfaction We recom mend that a licensed contractor perform the installation of all Jacuzzi Whirlpool Bath products Our war ranty does not cover improper installation related problems Specifications Roughing in Reference Installation Framing and Support service Access Electrical Connections Plumbing and Water Supply Operation Maintenance Troubleshooting Authorized Service Repair Parts BMH Jet amp 1 Position Air Control CONTENTS 2 Position Control Air amp Pump Motor ON OFF HTC Jet amp Suction Assembly Back Massage Jet Assembly 3 Position Control Pump Motor Assembly RapidHeat Heater Union Repair Kit Air Actuated Switch amp Strain Relief Warranty Date Purchased Purchased From Installed By Serial Number Model Owner s Record 1 2 3 4 5 8 13 14 18 14 15 16 16 17 18 19 20 NOTE To obtain a referral for a service agent in your area call 800 288 4002 You may also visit our web site at http www jacuzzi com To find the service agent listing click on For The Trade Then click on Electrical Mechanical Service Agents Depending on the problem click on Electrical Mechanical Repairs or Repair Parts or Accessories for a listing of authorized agents contractors or distributors Finish Surface or Shell Related Problems or SPECIFICATIONS Important Read complete instructions before beginning installation Each whirlpool ba
29. r over flow cover and cover screws are packaged in a sepa rate package within the kit to protect the trim finish Follow the installation instructions provided with the drain overflow kit After the drain is fully installed test for proper drainage If the unit does not drain properly rectify this condition before proceeding with the instal lation Jacuzzi Whirlpool Bath is not responsible for removal and or reinstallation costs NOTE Watertight installation of the drain is the installer s responsibility Drain leakage is excluded from the Jacuzzi Whirlpool Bath warranty of this product Plumbing Pump jets and suction fittings for the whirlpool sys tem are factory plumbed in schedule 40 PVC piping All Jacuzzi Whirlpool Bath products are factory tested for proper operation and watertight connections prior to shipping If leaks are detected notify your Jacuzzi Whirl pool Bath Dealer Do not install the unit Jacuzzi Whirlpool U961000F 12 04 Water Supply Consult local authorities for plumbing code require ments in your area IMPORTANT Proper installation of the fill spout plumbing and compliance with local codes are the responsibility of the installer Jacuzzi Whirlpool Bath does not warrant connections of water supply fittings and piping fill systems or drain overflow systems Nor is it responsible for damage to the bath which occurs during installation CAUTION A nonflammable protective barrier must be plac
30. specifications furnished bythe Company Some states do not allow limitations on how long an implied warranty lasts orthe exclusion or limitation of incidental or consequential damages sothe above limitations and exclusions may not apply to you RETURN OF WARRANTY CARD The attached Warranty Registration Card MUST be filled out by the purchaser within thirty 30 days from purchase and mailed to Jacuzzi Whirlpool Bath inorder forthis warranty to become effective Jacuzzi Whirlpool Bath P O Box 702168 Dallas TX 75370 2168 RESPONSIBILITIES OF OTHERS Inspecting the unit prior to installation is the responsibility of the installer or building contractor who acts on behalf of the user They are responsible for ensuring the unit is free of defect or damage Notices are placed on and in the unit and on the shipping carton advising the installer of this responsibility In the event of a problem the unit must not be installed The Company is not responsible for failures or damage that could have been discovered repaired or avoided by proper inspection and testing prior to installation Damage occurring in transit is the responsibility of the carrier The user or installer MUST open the crate and inspect the unit for damage when it is delivered If damage is discovered it must be reported immediately to the seller and the carrier in writing and an inspection requested Failure of the carrier to respond should be reported to the seller and the carrier
31. ted parts when pool and or spa chemicals are usedinthe unit optional bath equipment not manufactured by the Company but supplied by Dealer installer orthe Company the unit s prior usage as an operational display or defects that should have been discovered before installation This limited warranty does notinclude labor transportation or other costs incurred in the removal and or reinstallation ofthe original unit and or installation of a replacement unit any costs relating to obtaining access for repair orlossofusedamage including loss of sales profitor business advantage of any kind under any circumstances Bath units are excluded from any warranty coverage if any addition deletion or modification of any kind whatsoever has been made to the unit orto any component Warranty coverageis provided inthe United States of America and Canada EXCLUSION OF IMPLIED WARRANTIES IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FORA PARTICULAR PURPOSE ARE DISCLAIMED ALTOGETHER OR TO THE FULL EXTENT ALLOWED BY LAW NOTICE This warranty gives you specific legal rights and you may also have other rights which vary from state to state There are no warranties applicable to Jacuzzi Whirlpool Bath products except as expressly stated herein or as implied by applicable state andfederallaws The Company will notbe responsible for any statements or representations made in anyformthatgo beyond are broaderthan or are inconsistent with any authorized literature or
32. th arrives ready for installation completely equipped with motor pump assembly and plumbing and fittings necessary for whirlpool operation An optional drain overflow kit is available for installation on the bath Remove the bath from the carton Retain the shipping carton until satisfactory inspection of the product has been made Do not lift the bath by the plumbing at any time handle by the shell only Immediately upon receipt inspect the shell before installing Should inspection reveal any damage or defect in the finish do not install the bath Damage or defect to the finish claimed after the bath is installed is excluded from the warranty Jacuzzi Whirlpool Bath s responsibility for shipping damage ceases upon delivery of the products in good order to the carrier Refer any claims for damage to the carrier For definitions of warranty coverage and limitations refer to the published warranty information packed with the product All bath units are factory tested for proper operation and watertight connections prior to shipping Note Prior to installation the bath must be filled with water and operated to check for leaks that may have resulted from shipping damage or mishandling Jacuzzi Whirlpool Bath is not responsible for any defect that could have been discovered repaired or avoided by following this inspection and testing procedure RECTANGULAR BATHS Yaman EEN y 2n P 51mm H SIDE VIEW END VIEW SIDE VIEW END VIEW BAT
33. u larly purge your whirlpool system with Systems Clean as recommended For additional information about water content contact us for a copy of the Jacuzzi Water Quality Primer Lamp An optional lamp kit is available from your Jacuzzi Whirlpool Bath dealer for installation on your bath When the bulb burns out replace it from the back of the lamp fitting on the underside of the shell by pulling out the bulb receptacle Replacement bulbs 12V 7W are available from your Jacuzzi Whirlpool Bath dealer 11 Bath Additives NOTE DO NOT USE OIL OR OIL BASED BATH ADDITIVES If you want to use any kind of bath additive use only a small amount of low foaming powder or crystal sub stance the whirlpool action intensifies the foaming prop erties of soaps The use of certain bath oils bubble baths and bath additives may increase the level of accumulations of bath residue in the whirlpool system If excess accumu lations persist you should discontinue use of these products Suction Cover Strainer Maintenance Clean the suction cover strainer of hair and debris when necessary To do this remove the center screw and detach the square cover Clean the cover by back flushing debris from the holes Replace the suction cover immediately after cleaning When reinstalling orient the cover strainer with the small notch at the bottom The gasket must be inserted into the groove of the cover strainer before reinstalling onto the suction
34. unit for air circulation for cooling the motor and to supply sufficient air to the jets Do not insulate this area or around motor Service Access with Skirt An optional skirt fits along the side of the bath for above floor installations and is also an access panel for servicing Allow a space of atleast 8 inches away from the bath for skirt removal The skirt is designed to accommodate the added height of the tile linoleum or other floor coverings up to 1 1 4 inches above the floor and will be flush with the floor when installed More detailed instructions on skirt installation are pro vided with the optional skirt assembly SERVICE ACCESS CORNER BATH WITHOUT SKIRT desc 24 gt RIGHT HAND UNIT SHOWN A Preferred access B Acceptable alternative if access A is not possible C Optional access for accessory equipment NOTE Left hand unit access is on the opposite side mirror Image SERVICE ACCESS WITHOUT SKIRT ALTERNATE ACCESS 18 ani PREFERRED ACCESS Jacuzzi Whirlpool U961000F 12 04 Service Access with Integral Skirt Service access is through the removable skirt panels SERVICE ACCESS WITH INTEGRAL SKIRT REMOVABLE SKIRT ACCESS PANELS ACCESS AREA MOTOR Reinstalling Panel Hold at an angle to the skirt and insert clip under edge of skirt opening Bow the panel outward and insert clip on other side ACCESS PANEL SKIRT BOW ACCESS PANEL Or slide clips over bottom li
35. ur Jacuzzi Whirlpool Bath dealer for the complete line of whirlpool spas available Once the bath is installed remove any residue or for eign materials left over from construction Use turpen tine or paint thinner to remove stubborn stains paint or tar Other dirt can be cleaned off with a mild liquid de tergent on a damp cloth Scrape off plaster with a wooden or plastic edge do not use metal scrapers wire brushes or other metal tools as they will dam age the bath s surface Water Level Close the drain and fill the bath until water is at least 2 above the highest jet see water line indicated in the illustration Do not turn on the whirlpool system at any time if the jets are not completely immersed in water Running the whirlpool system when there is in sufficient water in the bath could result in water spray ing outside the bath area Running the whirlpool sys tem without water will damage the recirculating pump FILL TO AT LEAST 2 ABOVE HIGHEST JET TYPICAL BATH FITTINGS MAGIC TOUCH WHIRLPOOL ON OFF SWITCH A O FULLY ADJUSTABLE JETS SUCTION p m COVER NNN a DRAIN OVERFLOW Magic Touch Whirlpool Switch The Magic Touch whirlpool ON OFF switch conven iently located on the bath allows you to turn the whirl pool system on and off while in the bath Simply push down on the switch button to turn on the whirlpool sys tem To turn the system off push down on the button again If your bath has
36. your bath is influenced by three factors direction of flow force of water and force of air All baths manufactured by Jacuzzi Whirlpool Bath are equipped with fully adjustable PowerPro jets which are adjustable for all three factors Some baths have additional directionally adjustable jets which can be adjusted for direction and flow of air only Direction To change the direction of the water flow swivel the jet nozzle to the desired angle The jets can be directed individually toward any location on your body to provide a hydromassage The jets can also be ad justed so that they all point in the same direction clock wise or counterclockwise to circulate the water in a cir cular motion around the bath causing a total whirlpool effect Jacuzzi Whirlpool Bath U961000F 12 04 10 Water Force The high volume fully adjustable jets can be adjusted to control the force of the water coming into the bath For robust action increase the force of the flow by rotating the jet handles to the left counter clockwise For a more gentle effect rotate the handles to the right clockwise Never run the whirlpool sys tem with all the jets closed Force of Air Two knobs located on the bath serve as controls for the air induction system The intensity of the hydromassage whirlpool action is determined by the amount of air inducted into the water As the amount of air is increased the hydromassage action increases For maximum air indu
Download Pdf Manuals
Related Search