IOGear GBHFK231 User's Manual
Contents
1. Installation e gt Solar Power Bluetooth Hands free Car Kit GBHFK231 Table of Contents Package Content Requirements Device Overview Charging Your Car Kit Recommended Way of Using Your Car Kit Connect Car Kit to your Bluetooth enabled cellular phone Operating the Car Kit with Two Bluetooth enabled phones Using your Car Kit N O Oo A 11 18 22 LED Indication Restore to Default Settings Federal Communications Commission FCC Statement CE Statement Limited Warranty Contact 26 28 ZS 32 33 34 Package Content 1 x Solar Power Bluetooth Hands free Car Kit 1 x USB Car Charger 1 x USB Charging Cable 1 x Windshield Mount 4 x Suction Cups 1 x Sun Visor Mount 1 x User Manual 1 x Warranty Registration Card Your mobile cellular phone PDA or Smart Phone must be Bluetooth enabled and supports either Headset or Hands free profile in order to work with the Solar Power Bluetooth Hands free Car Kit IMPORTANT NOTE Before start using the Windshield Mount on your windshield check the state and local laws and ordinances where you drive Some state laws prohibit drivers from using suction mounts on their windshields while operating motor vehicles Other state laws allow the suction mount to be located only in specific locations on the windshield Many other states have enacted restrictions against placing objects on the windshield in locations that obstruct the driver s vision It is2. on the first phone and pick up the call from the second phone Quick tab the MFB button twice again to switch from the call on the second phone back to the call on the first phone 20 Rejecting call from the second phone When a new call comes in on the second phone press and hold MFB button for 3 seconds to reject the call from the second phone Switch between two calls on two phones Quick tab the MFB button twice to switch between the calls on two phones When on an active call short press MFB button to end the call and stay with the other call 21 Using your Car Kit Power On Power Off Answering a Call Ending a Call Reject a Call Long press the MFB button for 4 seconds until you hear a short beep The BLUE LED will flash 5 times and the Car Kit will automatically connect to the last connected phone Long press the MFB button for 4 seconds until you hear a short beep The RED LED will flash 5 times before powering off Short press the MFB button to answer the call Short press the MFB button to end the call Press and hold MFB button for 2 seconds to reject the call when you hear the ringing tone 22 Voice Dial Last Number Re Dailing If you cellular phone voice dialing is enabled short press the MFB button under standby mode and say the voice tag after hearing a beep Note Please ensure to record voice tag into the cellular phone before using voice dial function Functionality varies depe
3. solar power 1 Place the Solar Power Bluetooth Car Kit under direct sunlight exposure with 45 degree angle and have the solar panel facing toward sunlight 2 Leave the Car Kit under sunlight exposure for 18 hours to have the device fully charged The LED light on the Car Kit will light up during charging and it will turn off when charge completes 10 2 Recommended Way of Using Your Car Kit On the sun visor 2 Place the Car Kit with sun visor 1 Slide the Car Kit into the sun visor mount onto the sun visor Or your car mount Ge 3 Now you can talk safely while driving 11 Mounting the Car Kit on the windshield IMPORTANT NOTE Before start using the Windshield Mount on your windshield check the state and local laws and ordinances where you drive Some state laws prohibit drivers from using suction mounts on their windshields while operating motor vehicles Other state laws allow the suction mount to be located only in specific locations on the windshield Many other states have enacted restrictions against placing objects on the windshield in locations that obstruct the driver s vision It is the user s responsibility to mount the device in compliance with all applicable laws and ordinances 12 1 Take the Car Kit off the windshield 2 Clean the surface of your windshield mount where you want to mount the windshield mount gt 13 3 Push and hold the windshield mount agains
4. sure it is in standby mode Then press and hold button for 3 seconds until hearing a beeping sound 2 To turn off this feature under standby mode press and hold for 3 seconds until hearing a beeping sound and the Car Kit will power off automatically When power on the Car Kit again it will only connect to the last connected Bluetooth enabled cellular phone Note When the multi point feature is in use the Car Kit does not support three way calling feature 18 Pair Two Bluetooth enabled cellular phones 1 Before begin to pair two Bluetooth enabled phones with the Car Kit first you need to make sure to activate the multi point feature Please refer to page 18 for instructions 2 Complete the pairing process with first phone following the steps in page 16 3 Power off the Car Kit Press and hold the MFB button for 6 seconds to enter pairing mode again to pair and connect with the second phone following steps in page 16 4 When the pairing is completed with the second phone the Car Kit will automatically connect to the first phone 19 Note If the Car Kit does not connect back to the first phone or having problem staying connected with any one of the two phones try to power cycle the Car Kit and it should reconnect back to the two phones Answering call from the second phone during a call on the first phone When a new call comes in on the second phone quick tab the MFB button twice to hold the call
5. atically after the reset 2 When the Car Kit is not powered on turn on the Car Kit and press and hold both and buttons for 10 seconds until the BLUE and RED LED flash 5 times Then the Car Kit will resume standby mode automatically after the reset 26 Federal Communications Commission FCC Statement 15 21 You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user s authority to operate the equipment 15 105 b his equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no 29 guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a
6. circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help 30 THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device FCC RF Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment End users must follow the specific operating instructions for satisfying RF exposure compliance This transmitter must not be co located or operating in conjunction with any other antenna or transmitter 31 CE Statement This device has been tested and found to comply with the requirements set up in the council directive on the approximation of the law of member states relating to EMC Directive 89 336 EEC Low Voltage Directive 73 23 EEC and R amp TTE Directive 99 5 EC The product has been approved for LVD and covered the following countries Belgium Denmark France Germany Italy Portugal U K Spain Sweden 32 Limited Warranty IN NO EVENT SHALL THE DIRECT VENDOR S LIABILITY FOR DIRECT INDIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULT ING FROM THE USE OF THE PRODUCT DISK OR ITS DOCUMENTATION EXCEED THE PRICE PAID FOR THE PRODUCT The direct vendor makes n
7. nding on the phone models Please refer to your cellular phone user manual for details Short press the MFB button twice under standby mode 23 Adjusting the Volume Mute Un Mute Transferring Call from Car Kit to phone Press the or button repeatedly until you reach the desired volume level Short press the Mute button during a call to mute and the RED LED will turn on Short press the Mute button during mute mode to un mute the Car Kit and the RED LED will turn off Press both and during a call to direct the call from the Car Kit to cellular phone 24 Transferring Call Press Both and to direct the call back from cellular from phone to phone back to the Car Kit Car Kit 25 LED Indication Device Status Power Off Powering On Powering Off Standby Mode Low Battery LED Status LED Off BLUE LED flash once every 3 seconds RED LED flash once BLUE LED flash twice every 3 seconds RED LED flash once every 3 seconds 26 Device Status Call in Progress Pairing Mode Charging in Progress Charging Completed LED Status BLUE LED flash once every 6 seconds RED and BLUE LED flash alternatively RED LED on ED Feit 27 Restore to Default Settings 1 When the Car Kit is on and in standby mode press and hold both and buttons for 10 seconds until the BLUE and RED LED flash 5 times Then the Car Kit will enter pairing mode autom
8. o warranty or representation expressed implied or statutory with respect to the contents or use of this documentation and especially disclaims its quality performance merchantability or fitness for any particular purpose The direct vendor also reserves the right to revise or update the device or documentation without obligation to notify any individual or entity of such revisions or updates For further inquiries please contact IOGEAR 33 IOGEAR 19641 Da Vinci P 949 453 8782 Foothill Ranch CA 92610 F 949 453 8785 Visit us at www iogear com 2009 IOGEAR Part No M1344 IOGEAR the IOGEAR logo are trademarks or registered trademarks of IOGEAR Inc Microsoft and Windows are registered trademarks of Microsoft Corporation All other brand and product names are trade marks or registered trademarks of their respective holders IOGEAR makes no warranty of any kind with regards to the information presented in this document All information furnished here is for informational purposes only and is subject to change without notice IOGEAR Inc assumes no responsibility for any inaccuracies or errors that may appear in this document 34 Customer s Record The model number and serial number of this product can be found on the product package You should note this serial number in the space provided below and retain this book plus your purchase receipt as a permanent record of your purchase to aid in identification for Warrant
9. t the windshield until the windshield mount is securely attached to the windshield Note If you have problem attaching the windshield mount to your windshield apply small amount of water and wet the suction cups and try again 14 4 Slide your Car Kit back into the windshield mount and now you can charge the Car Kit battery with solar energy 15 Connect Car Kit to your Bluetooth enabled cellular phone 1 Turn on the Bluetooth connec tion on your phone and enable the pairing mode of the Bluetooth connection Make sure your phone and the Car Kit is no more than 3 feet apart 2 Make sure the Car Kit is powered off Long press the MFB button of the Car Kit for 6 seconds to enter the pairing mode 16 3 Your cellular phone will now start to look for the Car Kit When the Car Kit is found your phone will display GBHFK231 from the list of devices and you will be asked to enter the pairing code Enter 0000 and press OK to establish the connection Note If the pairing process can not be completed within 2 minutes after pairing mode is activated the Car Kit will power off automatically Please repeat above steps again to pair your Bluetooth enabled cellular phone and the Car Kit 17 Operating the Car Kit with Two Bluetooth enabled phones Activate multi point connection 1 The default setting of Car Kit s multi point connection is off To turn this on power on the Car Kit and make
10. the user s responsibility to mount the device in compliance with all applicable laws and ordinances Device Overview NO Ooo DS W Volume Up Multi function button MFB button Volume Down Solar panel Mute button USB charging port IL Charging Your Car Kit Before you begin using your Solar Power Bluetooth Hands free Car kit it is recommended to fully charge the device to ensure optimal performance Using the USB cable 1 Plug the micro USB connector end of the USB charging cable to the Solar Power Bluetooth Car Kit and the other USB Type A connector end to any available SUB port on your computer or an AC power adapter with USB port not included VA 2 The LED light on the Car Kit will light up during charging and it will turn off when charge completes It will take approximately up to 3 hours to get a full charge thru the USB port of your computer 7 Using the car charger 1 Plug the micro USB connection end of the USB charging cable to the Solar Power Bluetooth Car Kit and the other USB Type A connector end to the USB Type A female port of the included car charger 2 Plug the car charger completely into the cigarette lighter in your car and turn on the power of your car The LED light on the Car Kit will light up during charging and it will turn off when charge completes It will take approximately up to 3 hours to get a full charge thru the car charger Using
11. y Service purposes Model Number Serial Number 35 FUN IOGEAR offers connectivity solutions that are innovative fun and stylish helping people enjoy daily life using our high technology products GREEN IOGEAR is an environmentally conscious company that emphasizes the importance of conserving natural resources The use of our technology solutions helps reduce electronic waste Edo amp HEALTH IOGEAR supports healthy and fit lifestyles By integrating products with the latest scientific develooments IOGEAR s solutions enhance the life of end users PART NO M1344 2009 IOGEAR
Download Pdf Manuals
Related Search