IntraServer Technology 5232E User's Manual
Contents
1. IntraSyerver TREC AN OTL OGY ING ITIpci 5232E Four Port Ethernet and Fast Ethernet PCI Host Adapter Installation and User s Guide Order Number 9806 5232M IntraServer Technology Inc Copyright 1998 quad_enet doc Copyright 1998 First Printing June 1998 Copyright Copyright 1998 IntraServer Technology Inc No part of this manual may be reproduced in any form mechanical or electronic without the prior written consent of IntraServer Technology Inc Seven October Hill Road Holliston MA 01746 Trademarks The following are trademarks of IntraServer Technology Inc ITIpci ClusterReady and the IntraServer logo Al other trademarks are the property of their respective holders and acknowledged Information Subject to Change The information in this manual is subject to change without notice and should not be construed as a commitment by IntraServer Technology Inc Reasonable efforts have been made to assure the accuracy of this manual IntraServer Technology Inc assumes no liability resulting from errors or omissions in this manual or from the use of the information in the manual IntraServer retains the right to make changes to this manual and the products without prior written notification Readers Comment Card The Reader s Comments form at the end of this document requests your critical evaluation to assist in preparing future documents IntraServer Technical Support Technical support and information is a2. Saveur Prodocods Adapters finding 4 From the Select Network Adapter dialogue select Have Disk 13 E te pei cares ates TE ped WT PY Deco E arin 8 cgi 14 6 From the Select OEM Option dialogue Select IntraServer ITIS5232E Four Port 10 100 Mbps Ethernet adapter and select OK Select OEM Option Choose a software supported by this hardware manufacturer s disk IntraServer Tl4e 0 10 100 Mbps Adapter IntraServer T 5232E Four Port 10 100 Mbps Adapter cancel toe 7 A Connection Type dialog box will allow you to select the connection type appropriate for your network configuration The default connection type is AutoSense which should be correct for most network connections IntraServer 1715232E Four Port 10 100 mpbs Ethernet Setup x Connection Type Choose the proper cable type for the network adapter Select Help for a detailed Cancel description of the available options of the list 8 Should you need to change the media connection type be certain to select the correct connection type for your network If not the adapter port will not be able to link to the network IntraServer 1715232E Four Port 10 100 mpbs Ethernet Setup Connection Type AutoSiense Autos ense Choose the proper cable Wf 1 OB aseT TP Ed description of the available 406 5 67 TP Full Duplex 1O0B aseT TP 100 1006 aseTs TP 100 Full Duple 15 9 Upon c
3. CTUGIN A oia E E EATER iat Gana iste ee 28 Digital s SRM Console Settings isesccnciscctvvecacsctctieticersaccccusnincdkvesncstucdieiusivauccs outainscd aaia 28 Displaying and Setting Ethernet Port Characteristics ccccsesesenseennnnennneceeeceeeeeeeeeeeeeeeeeeeeeeeeeeeeeees 28 PUD DOCTIGIN B cnai ious avendeusadeveousdeanevaseuag rouoeuenbe viasesanstsaveweseeaeiaueeseohetareeious 30 Connector Pin ASSIgnMe its sicesscdccesiecdsveeteeccsepieedssessegdesentevesnceheus conadseassensecesxastiusseveleucesesisessies 30 Calo limi ReguiremeniS osseeseeeics sscecscasecsiiscscdecdssssceaudessseacsceeeesedssdestecsssvaudessseesscse0usuecssbestecssersecees 31 Appendix C Troubleshooting sepine i E E Eaa 32 Windows NIT Version 4 0 ama SS lensa aaee eL aaa Eaa 32 Erron messat o anena a A ee edema aaa 32 Driver imina Zanon eNOS eana A E a 33 Diver mime CITOI S aee a E E EE EEE EE EEE 33 Windows IS sarsii ei a aa aa iaai 34 Appendix D Adapter Specifications sssssssssosssesosoooseseeeeeseeeeeceeeeseceececeeeeeeeeeeceseessssse 36 ITI 5232E Four Port 10 100 Ethernet PCI adapter cccsssscccccccccsssssssssssssssssssccees 36 Tables Table 1 ITI 5232E Adapter Models Table 2 Connections and Indicator LEDs Table 3 Contents Of Software Distribution Floppy Table 4 Digital UNIX and OpenVMS SRM Console Media Selection Table 5 8 Pin MJ Connector Pin Assignments Table 6 Adapter to Network Hub Wiring Table 7 Adapter to Adapter poin
4. may vary slightly from these examples based on your machine s current network configuration and options See your system administrator for any additional information Note Digital s Alpha systems use a dynamic link library file DLL called a hardware abstraction layer HAL This file can be found on your boot disk at the location os hal dll This is a system file and is hidden You must use the show system and hidden files option under explorer to see this file Certain Alpha systems will hang after installing multi port Ethernet cards unless this file is updated to hal dll dated on or after 26 MAY 1998 If you experience this hang shut down the machine and remove the ITI 5232E from your system Contact Digital for an updated HAL and installation instructions 1 From the Windows NT START Menu select the Control Panel icon 2 From the Control Panel menu select the Network icon f m iaig SL Ae r Door Pega LE Dipi aTi D 3s a er La EL If a dialog box asks you Do you want to install NT Networking select YES and continue Place the Windows NT installation media the CD ROM reader and complete the Windows NT network installation Consult Windows NT documentation if you are unfamiliar with this process Follow the on screen prompts until you are prompted for a Network Adapter Type 3 From the Network dialog select the Adapters tab then select Add identification
5. will be displayed 6 Put the Software Installation Floppy in your Floppy drive then select Next gt Add New Hardware Wizard This wizard will help vou quickly install a new piece of hardware To begin installing your new hardware click Mest Cancel 6 Windows 95 will read the installation floppy and will automatically find the ITI 5232E Four Port Ethernet controller Select Finish If you are the Select Device dialog box to select the ITI 5232 Four Port 10 100 Mbps Ethernet Adapter from the list and select OK 18 r Select Device IntraServer ITl4ee0 21140 based 10 100 mpbs Ethernet Controller IntraServer T5232 Four Port 10 100 mbps Ethernet Controller 12 Windows 95 may prompt you to insert the distribution media disk s to be installed at this time 13 Some files will be copied from your distribution media disk s and some from the OEM distribution floppy disk Copying Files 14 If Windows prompts you for a file location of the distribution files select the default location A and select OK Install From Disk 19 15 When all necessary files have been copied to your system select Finish from the Add New Hardware Wizard dialogue Add New Hardware Wizard Windows has finished installing the software necessary to support your new hardware Cancel 16 The preceding steps will be repeated for EACH of the four ports detected by Win
6. AO EE E E aN 6 ITI 5232E Four Port Ethernet and FAST Ethernet Kit Contents ccccccccsssssssccees 7 Connectors and Indicator LEDS sssri ansss aean aa eaaa a aai 8 Hardware Installat Oi sesseur osr nEaN EEEN EEE A E AEA AEREE 9 System Requirements s artsksrsacoronisusrensiodirosana carena e aeea arad rassaa aeiiae asana e oriai asiasia take 9 Instalo the ad apler siacccseccstescseccsuethscvccasscacscavsaesesece sca duathscssdasscanseausewscneceeacdases scbusechoosesomteszessee 9 Network Device Driver Installation INStructiONns cccccsccssssssesssseeseesssessssessssssesssssseeess Il Windows N E reciia a E a 11 Contente Ore GEIVEL kiac a E E E 1 Installing the ITI 5232E DC21X4 Driver on Windows NT cccccccecccceeessseeeeeeeeeeeeeeeeaeeaeeeeees 12 Windows 95 Installation for PCI System cccccsccccccssssssssssssssssssssssscssscccccccccsscsssssssssees 18 INGE WY ALC ccbecdasccteasiecctestasascceveudesesdescenselsucetaasascsadeseadestodouseaasebecebasterasacasascesoutensesssteadstestecasadeseeeews 23 MOVIN SPIA I I EE AA O O O A A 25 For information regarding drivers installation and support for Linux please visit our World Wide Web site at http intraserver com support faq htMl seeeeeeeccsscsssssssesseceececossssssssssssssseeeee 25 Deity UIN DN anani E N TE EE 26 Digital Open VMS wescccsecsccsscads cect tatecetesiiacesdenseweeerdecte datccvesedanss dausewessudadecsiatecvesiaaewedanzeeeeensvads 27 PDD
7. NIX uses BOOTP For example to set a port to MOP VMS use gt gt gt set ewa0_protocol MOP Note Port 0 will be the lowest controller letter found by the SRM console A if there are no other Ethernet ports in the system If there is an onboard Ethernet controller it will be assigned port letter A and the ports on your ITI 5232 will be assigned B C D and E for ports 0 1 2 and 3 respectively 29 Appendix B Connector Pin Assignments Each of the Four 8 pin MJ connectors for 10 100 Mb sec are wired as shown in Figure 2 Figure 2 8 Pin MJ Connector Front With the connection pins assigned as shown in Table 5 Pin Number 1 CO N A ny AININ 12345678 _ Transmit _ Transmit _Receive _No Connection _No Connection _ Receive _No Connection _No Connection Table 5 8 Pin MJ Connector Pin Assignments Signal Name TX TX RX NC NC RX NC NC Connection from the ITI 5232 adapter to a network hub must be made as shown in Table 6 30 Table 6 Adapter to Network Hub Wiring Connection from the ITI 5232E adapter to another network adapter point to point must be made as shown in Table 7 Adapter 1 Adapter 2 8 SL TX RK TX 2 OE RX eS _ RX _ 6 c gt 2 _TX 8 8 Table 7 Adapter to Adapter point to point Wiring Cabling Requirements In order for your network to operate properly you must use a category of network cabling that is
8. _ERROR_CODE_UNSUPPORTED_CONFIGURATION DC21X4_ERRMSG_MEDIA The selected media port is not supported by the board NDIS_ERROR_CODE_INTERRUPT_CONNECT Interrupt initialization failed NDIS_ERROR_CODE_TIMEOUT DC21X4_ERRMSG_LOAD_CAM DC21X4 CAM initialization failed Driver run time errors 33 NDIS_ERROR_CODE_HARDWARE_FAILURE DC21X4_ERRMSG_SYSTEM_ERROR System_Error interrupt bus parity error NDIS_ERROR_CODE_HARDWARE_FAILURE DC21X4_ERRMSG_TXM_JABBER_ TIMEOUT Transmit Jabber timer expired Windows 95 If the adapter is not detected by Windows 95 after installing the adapter and rebooting Windows 95 check the following I Double click on My Computer Control Panel System to display the System Properties Page Select the Device Manager tab from the System properties page in order to view the list of devices in the PC Check in the list of devices for an entry labeled Other Devices If an Other Devices entry exists double click on it to display the list of devices under it Check the list for an entry labeled PCI Ethernet Controller If this exists select highlight it by clicking on it and then click on the Remove button at the bottom of the page to delete it Reboot the PC and the adapter should now be detected 34 35 Appendix D Adapter Specifications ITI 5232E Four Port 10 100 Ethernet PCI adapter Hardware Interrupts ITI 5232E N supports shared interrupts ITI 5232E O U does not sup
9. appropriate for the data rate of the channel For 1OMb s operation Category 3 4 or 5 cable is appropriate When operating in LOOMb s or 1OOMb s Full Duplex a Category 5 cable should be used The maximum cable segment length supported at 1 OOMb sec speed on Category 5 cable is 100M Any single cable segment adapter to adapter or adapter to network hub must be within the 100M length requirement 31 Appendix C Troubleshooting Windows NT Version 4 0 and 3 51 The most common problem encountered on Windows NT for Ethernet devices is a mismatch of the port s speed and media settings to those in use on the network The most simple check of correct cabling is to observe the status lights on the handle of the card Once the card is installed in the system the software is installed and the module is wired to your network hub the LINK light should be illuminated If LINK fails to light check that your cable type and media settings are correct Appendix B provides cable information for all configurations If you are connected to a FAST hub be sure card is set to AUTO FAST or FAST Full Duplex depending on the capability of your hub If you are connected to a LOMb sec hub the card should be set to AUTO Twisted Pair or Twisted Pair Full Duplex depending on the capability of your hub Cables from the ITI 5232E to a hub MUST NOT BE CROSSOVER Cables from the ITI 5232E to another ITI 5232E MUST BE CROSSOVER ITIP If you are cer
10. dows 95 You will need to repeat the above procedures until each of the four ports have been added to your configuration 17 Each port on the ITI 5232E Four Port Network adapter will be given an entry in the adapter list in the Network dialogue Network Ei Configuration Identification Access Contral The following network components are installed a Client for Microsoft Networks eee af IntraServer ITI5232 Four Port 10 100 mbps Ethernet Cont ef IntraServer TI5232 Four Port 10 100 mbps Ethernet Cont dy IntraServer ITI5232 Four Port 10 100 mbps Ethernet Cont JY IntraServer ITI5232 Four Port 10 100 mbps Ethernet Cont Add Remove Properties Primary Network Logon Client for Microsoft Networks File and Print Sharing Description coca 18 The Enhanced mode driver should be used and is selected by default 20 IntraServer 1115232 Four Port 10 100 mbps Ethernet E E 19 The ITI 5232E is capable of full AutoSense which should allow plug and play operation with your network Should the need arise to specify the physical media select the Advanced tab then select Connection Type and select the connection type that matches your network IntraS erver 1115232 Four Port 107100 mbps Ethernet fz x Burst Lenan a autoSense F Connection Type Interrupt Mitigation Map Registers No Cable Indication FReceve Butters Snooze Made Store And Forward Tran
11. iver Actions menu Select a driver and press Enter If the desired IntraServer driver is not on the list proceed to Step 5 Insert the IntraServer Setup diskette into drive A and press lt INS gt to install the unlisted driver Press Enter The system scans path a for uninstalled drivers Press Enter to install the NetWare 4 x driver in drive A Select yes to copy the driver DC21X4 23 9 Enter information as prompted You may modify the adapter s default configuration by changing its parameters when prompted The default settings provide best results in most cases 24 Linux For information regarding drivers installation and support for Linux please visit our World Wide Web site at http intraserver com support faqg html 25 Digital UNIX Drivers for the ITI 5232E are on the Digital UNIX distribution kit beginning with Version 4 0D Digital UNIX will identify the ITI 5232E as four 21140 based Ethernet controllers Once the hardware 1s installed in your system boot the system using genvmunix in the following manner gt gt gt boot file genvmunix This will cause Digital UNIX to scan all hardware devices in the system and identify the ITI 5232E Four 21140 based Ethernet adapters will be identified Create a new kernel with support for the four Ethernet ports identified in genvmunix by using the doconfig command doconfig When doconfig completes backup your existing kernel as follows cp vmunix v
12. l UNIX OpenVMS MS DOS Linux Two ITI 5232E models are available as described in Table 1 Model Interrupts Interrupt Assignment Description a A L ITI 5232E N 1 Channel 0 Interrupt A Four Port Channel FAST Ethernet Adapter for Channel 1 Interrupt A Windows NT Windows 95 operating systems Channel 2 Interrupt A that support sharing of PCI interrupts _ Channel 3 Interrupt A _ ITI 5232E O U 4 Channel 0 Interrupt A Four Port Channel FAST Ethernet Adapter for Channel 1 Interrupt B Digital UNIX OpenVMS operating systems that Channel 2 Interrupt C do not support sharing of PCI interrupts Channel 3 Interrupt D Table 1 ITI 5232E Adapter Models ITI 5232E Four Port Ethernet and FAST Ethernet Kit Contents Your I TI 5232E kit includes the items shown below Verify that you have the following items before you proceed with the installation e TI 5232E Four Port Ethernet and FAST Ethernet Adapter e Software installation kit e This installation guide Connectors and Indicator LEDs The ITI 5232E provides four 8 pin Modular Jack MJ connectors for connection with your network Each of these four ports supports either Twisted Pair Category 3 or 5 cable for l OMb s connections or Category 5 cable for 1OOMb sec operation Figure shows the ITI 5232E Adapter connectors and indicator LEDs Port 0O Port 1 Port 2 Port 3 Pont Port Port WN FF CO Port Figure 1 Connectors and Indica
13. munix sav Then copy the new kernel created by doconfig to vmunix and shutdown and reboot with your new kernel If you are unfamiliar with doconfig refer to your Digital UNIX documentation for additional information Note Digital UNIX relies on the settings for media type and speed set by the SRM console See Appendix A for more information 26 Digital OpenVMS Drivers for the ITI 5232E are on the Digital OpenVMS distribution kit beginning with Version 7 1 Digital OpenVMS will identify the ITI 5232E as four 21140 based adapters Follow the documentation for the network software you will be running on the adapter for specific configuration information Note Digital OpenVMS relies on the settings for media type and speed set by the SRM console See Appendix A for more information Note If you are connecting Point to Point to another adapter do not select Auto Sense for ewa0_mode Also many hubs do not support Auto Sense it is therefore recommended that the correct media type and speed are selected manually 21 Appendix A Digital s SRM Console Settings When the ITI 5232E is being used in a Digital Alpha platform running OpenVMS or Digital UNIX the SRM console is used to set the port speed media cable type and boot protocols and can also be used to test the module After powering your system up and before booting your operating system the system will stop at the SRM console prompt On a uni processor machi
14. ncrossed Twisted Pair cable After installation re assemble the system enclosure and proceed with Software installation 10 Network Device Driver Installation Instructions Windows NT The ITI 5232E Four Port Ethernet and Fast Ethernet adapter uses the industry leading Fast Network Engine Digital s DC21143 PCI MAC Digital s DC21X4 SYS mini port driver is used to support the four Ethernet channels on the card Contents of the driver kit Your ITI 5232E kit includes a floppy disk which contains the Windows NT and Windows 95 drivers The floppy disk contains the following files and directories Operating Architecture File Name File Description A WINNT ALPHA DC21X4 SYS The Alpha executable driver file for DC21143 Ethernet Chip INTEL DC21X4 SYS The Intel executable driver file for DC21143 Ethernet Chip A WIN95 DC21X4 SYS The Intel executable driver file for DC21143 Ethernet Chip ANDIS VXD _NDIS Wrapper file A DISKI Flag file for NT NETPCI INF Win 95 Setup information file OEMSETNT INF NT Setup information file README TXT Information released since the last publication of the _documentation if any RELEASE NOT Information specific to this software release if any Table 3 Contents of Software Distribution Floppy Installing the ITI 5232E DC21X4 Driver on Windows NT Follow the procedure below to install the NT driver on your Intel or Alpha based system The choices you are given
15. ne the SRM prompt is gt gt gt and on the primary processor of a multi processor machine 1s PO gt gt gt Digital uses a set of Environment Variables to store the settings of certain user definable parameters which are passed to the operating system to allow the users configuration information to stay consistent when the SRM passes control of the system to the operating system Displaying and Setting Ethernet Port Characteristics The Alpha console recognizes the Ethernet device as an EW port There are two commands that are necessary for setting and showing the Ethernet port SET and SHOW Use SHOW to display characteristics of the Ethernet port gt gt gt Show EWn0_MODE Where n is the Ethernet port letter Use SET to set characteristics of the Ethernet port The available settings for Ethernet media type are shown in Table 4 Parameter Settings Description EWn0_MODE TWISTED PAIR 10Mb sec Twisted Pair FAST 100Mb sec Twisted Pair Half Duplex FULL DUPLEX TWISTED PAIR Full Duplex Twisted Pair AUI Not Supported BNC Not Supported FAST FD FAST Full Duplex Table 4 Digital UNIX and OpenVMS SRM Console Media Selection 28 For example to set the media type and speed to FAST Twisted Pair enter the command gt gt gt set ewa0Q_ mode FAST If you will be remote booting via the Ethernet you must also set the boot protocol to match that of the boot node Typically OpenVMS uses MOP protocol and U
16. nician for additional suggestions CAUTION Only equipment certified to comply with Class B computer input output devices terminals printers etc should be attached to this equipment and must have shielded interface cables This device complies with part 15 of the FCC rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Each host adapter is equipped with an FCC compliance label which shows the FCC Identification number The full text of the label is in the preceding paragraph Finally any changes or modifications to the equipment by the user not expressly approved by the grantee manufacturer could void the user s authority to operate such equipment Canadian Compliance Statement This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations Cet appareil numerique de la classe B respecte toutes les exigences du Reglement sur le material brouiller du Canada European Compliance Statement WARNING This is a Class B product In domestic environments this product may cause radio interference in which case the user may be required to take adequate measures Please write to IntraServer Technology Inc Seven October Hill Road Holliston MA 01746 with regards to any questions on this product TIP OGUICHION siene
17. ompletion the selected adapter port s is are added to the Installed Adapter Cards list in the Network Setting box the number prefixing the adapter is the adapter port number Pz Inaaervar TISTI Fou Part 1100 M bpa tbat SP T iea a eeir TSZIIE Foa Part TOTO Mba Eterna PQ irtraeree TES Pou Part 104 bpe Ebera Saree SESE Pow Pot 1000 Mbps Erhi 10 Select OK to complete the Network Setting initialization Based on the protocols you are running one or more dialog boxes may appear See your network administrator for appropriate settings for your network for each of the dialog boxes A typical dialog TCP IP shown for example Microsoft TCP IP Properties 2 IntraServer ITI5232E Four Port 10 100 Mbps Adapter 7 192 168 104 205 aaa 255 255 16 11 Shutdown and reboot the system Hetwork Settings Change Windows 95 Installation for PCI systems The following step should be taken in order to use the IntraServer Technology Inc ITI 5232E Four Port Fast Ethernet 10 100 adapter in a system running Windows 95 1 Power the machine down unplug the AC power line and remove the access cover 2 Install the ITIS5232 into an unused PCI slot Attach the network cable s from the card to your existing network device 3 Replace the access cover of your machine 4 Replace the AC power line and boot Windows 95 5 When Windows 95 detects the new hardware a message New Hardware Found PCI Ethernet Controller
18. port shared interrupts Base I O Addresses Assigned by BIOS Data Transfer Rates Up to 800 Mbps in Fast full duplex mode Power Requirements PCI Universal 3 3 or 5 volts at 17 watts Environmental Operating Temperature 0 to 55 C Humidity 5 to 85 non condensing Altitude 3000m maximum Ethernet Standards IEEE 802 3 10 Base T IEEE 802 3u 100 Base T Certifications FCC Class B CE Class B Electrical Connections 4 RJ 45 female Network Speeds Supported 10 Mbps per Ethernet Network 20 Mbps Full duplex Segment 100 Mbps 200 Mbps Full duplex Indication LEDs Link Activity 100TX link 36
19. s e UTP category 3 4 or 5 cable type dependant on your network type For multi channel adapters such as the ITI 5232E it is required that your host system firmware or BIOS support PCI bridging If your host does not support PCI bridging contact your system vendor for a BIOS upgrade If your system can not be brought into compliance with the PCI bridge specification then you will not be able to use multi channel ITIpci host adapters Installing the adapter The following procedure should be used to install the ITI 5332E adapter 1 Turn OFF the power to the computer system and to all peripherals directly connected to the system monitor printer external SCSI enclosures etc 2 Unplug the system from the AC power line 3 Use an anti static strap or precautions to avoid static discharge to your computer system or the ITI 5232E adapter 4 Remove the access cover from your system refer to the system s documentation 5 Locate a free PCI expansion slot small white connector on the system s motherboard and remove the screw and metal bracket for the selected slot Be certain not to install the adapter in an ISA or EISA slot which are longer than the PCI slots 6 Install the adapter in the selected slot The module should fit without forcing and should line up with the I O bulkhead Be certain that the adapter is fully seated in the slot 7 Replace the retaining screw removed in step 5 8 Connect to your Ethernet HUB using u
20. smit Threshold 100 Transmit Threshold 10M 20 Select OK Based on the network protocols running on your system one or more dialogue boxes may appear See your network administrator for the network settings for this machine 21 21 When prompted allow the machine to restart to allow the new network settings to become active 22 NetWare The Novell Netware driver DC21x4 is used with both Netware 3 1x and Netware 4 x servers Netware 3 x Server Driver ie Prepare the hard drives of your server according to the instructions in your Netware 3 1x documentation While the server is down insert the IntraServer Setup diskette into your server s A drive Copy the contents of a netware 311 or a netware 312 to the disk from which you boot Netware 3 1x 4 Type SERVER at the DOS prompt press Enter to boot the Netware 3 1x Server 5 Type LOAD INSTALL at the server console prompt and press Enter 6 Select System Options 7 Select Edit AUTOEXEC NCF File 8 Edit the autoexec ncf file You must load the device driver once for each port used NetWare 4 x and 4 11 The Novell Netware driver DC21X4 is used with Netware 4 11 servers Type LOAD INSTALL at the server console prompt and press Enter On the Installation Options menu select Driver options load unload disk and network drivers On the Driver Options menu select Configure Network Drivers The system displays the installed network drivers and the Additional Dr
21. t to point Wiring Table 8 DC21X4 NT driver error codes Figures Figure I Connectors and Indicator LEDs Figure 2 8 Pin MJ Connector Front lI 28 30 3 3 33 30 Introduction IntraServer s Four Port ITI 5232E provides four FAST 10 100Mb sec channels from a single PCI host slot providing the maximum network integration for high performance network server needs Each of four ports is capable of running FAST FAST Full Duplex or 10Mb sec for configuration flexibility allowing a single card to communicate with FAST or Standard Ethernet systems simultaneously With each port capable of up to 200Mb sec in FAST Full Duplex mode a single ITI 5232E is capable of up to 800Mb sec ITI 5232E features include High performance PCI bus master 32 bit direct memory access DMA architecture Four independent 10 100 Digital 21143 PC Ethernet channels for optimal network performance Support for all Alpha and Intel Operating systems including Windows 95 Netware Windows NT OpenVMS Digital UNIX and Linux Direct 1OBase T and 100Base TX network connection with full auto negotiation support Half and Full Duplex mode of operation Jumperless Plug and Play implementation Speed Link Status Transmit and Receive activity LEDs 3 3 and 5 0 volt universal PCI support All major operating systems are supported on the adapter including Windows NT Windows 95 Windows 3 x OS 2 NetWare 3 x 4 x Digita
22. tain your cable type is correct but you are not seeing LINK setting the port to match the hub port exactly ex FAST not AUTO Some hubs have trouble with cards set to AUTO negotiate Error messages The error messages are logged in the Windows NT Error Log and can be seen using the Error Log Viewer in NT s Administration Tools group Each error message has a standard NDIS error code and a driver s additional code The additional codes are listed in Table 8 Error Message _Code DC21X4_ERRMSG_REGISTRY _ 0x01 DC21X4_ERRMSG_ALLOC_MEMORY _ 0x02 DC21X4_ERRMSG_SROM _ 0x03 DC21X4_ERRMSG_MEDIA _ 0x04 DC21X4_ERRMSG_LOAD_CAM 0x05 DC21X4_ERRMSG_SYSTEM_ERROR _ 0x06 32 DC21X4_ERRMSG_ TXM JABBER TIMEOUT 0x07 Table 8 DC21X4 NT driver error codes Driver initialization errors NDIS_ERROR_CODE_UNSUPPORTED_CONFIGURATION DC21X4_ERRMSG_REGISTRY The AdapterType Registry s key is missing or its value is unsupported by the adapter board NDIS_ERROR_CODE_ADAPTER_NOT_FOUND No board matching the AdapterCFID Registry s key value was found plugged into the PCI bus or in the slot specified in the Registry NDIS_ERROR_CODE_OUT_OF_RESOURCES DC21X4_ERRMSG_ALLOC_MEMORY Not enough memory to allocate space for the Adapter data block NDIS_ERROR_CODE_INVALID_VALUE_FROM_ADAPTER DC21X4_ERRMSG_SROM Invalid data read from the adapter s serial ROM NDIS_ERROR_CODE_NETWORK_ADDRESS No readable burnt_in or software configured station address NDIS
23. tor LEDs Table 2 describes the TI 5232E Four Port Fast Ethernet Adapter connectors and indicator LEDs 0 Channel 0 8 pin MJ Connector 10 100 Mb s twisted pair network connector for Channel 0 2 Channel 1 8 pin MJ Connector 10 100 Mb s twisted pair network connector for Channel 1 Channel 2 8 pin MJ Connector 10 100 Mb s twisted pair network connector for Channel 2 Channel 3 8 pin MJ Connector 10 100 Mb s twisted pair network connector for Channel 3 Channel 0 Indicator LEDs 100 Mb s Left LED Activity Center LED Link Right LED Channel 1 Indicator LEDs 100 Mb s Left LED Activity Center LED Link Right LED Channel 2 Indicator LEDs 100 Mb s Left LED Activity Center LED Link Right LED Activity Center LED Link Right LED Table 2 Connections and Indicator LEDs Channel 3 Indicator LEDs 100 Mb s Left LED Hardware Installation This chapter describes how to install the ITI 5232E adapter in your PCI based bus master compatible computer and how to connect it to your network The ITI 5232E host adapter is Plug and Play on the host systems PCI bus and no configuration of the adapter hardware is necessary System Requirements Before you begin the installation procedure you will need e An available PCI bus master expansion slot e A system that is compatible with the PCI Specification Version 2 1 e A floppy disk drive for loading the software driver
24. vailable by calling IntraServer Technology Inc direct at 508 429 0425 or your product reseller IntraServer Technology Inc s World Wide Web site is at http www intraserver com Product information support FAQ s and device drivers are available at the Company s web site Class B Device Certification Statements Federal Communications Commission Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against a harmful interference in residential installations This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause interference to radio or television equipment reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Move the equipment away from the receiver Plug the equipment into an outlet on a circuit different from that to which the receiver is powered If necessary the user should consult the dealer or an experienced radio television tech
Download Pdf Manuals
Related Search