Home

Intel DG33FB User's Manual

Contents

1. intel Intel Desktop Board DG33FB Product Guide Order Number D83431 001 Revision History Revision Revision History Date 001 First release of the Intel Desktop Board DG33FB Product Guide April 2007 If an FCC declaration of conformity marking is present on the board the following statement applies FCC Declaration of Conformity This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation For questions related to the EMC performance of this product contact Intel Corporation 5200 N E Elam Young Parkway Hillsboro OR 97124 1 800 628 8686 This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on
2. 7 Key no pin Port2L 9 10 Sense2 Ret QN OOO EL ia taa kaa ka ka ka a Ground 7 sl cod II AAA AAA No Key no pin 93 Connection RXDH TXD 131 48 DTR Ground 5 z DSR RTS 71 8 cts b No Connection Alternate T RI BS Front Panel 83 1 Power LED OM20009 Item Description Item Description A IEEE 1394a E Alternate front panel power LED B Front panel audio F Front panel C Serial port G USB 2 0 D Chassis Intrusion Figure 23 Internal Headers 45 Intel Desktop Board DG33FB Product Guide Connecting to the IEEE 1394a Header See Figure 23 A for the location of the IEEE 1394a header Table 4 shows the pin assignments for the header Table 4 IEEE 1394a Signal Header Names Pin Signal Name Pin Signal Name OIN WW e TPA1 2 TPA1 Ground 4 Ground TPA2 6 TPA2 12 V 8 12 V Key no pin Ground Installing a Front Panel Audio Solution for Intel High Definition Audio Figure 23 B shows the location of the front panel audio header Table 5 shows the pin assignments for the front panel audio header 46 Table 5 Front Panel Audio Header Signal Names for Intel High Definition Audio PORT 1L 2 GND PORT 1R 4 PRESENCE PORT 2R 6 SENSE1_RETURN SENSE_SEND 8 KEY no pin PORT 2L SENSE2 RETURN To install the cable that connects the front panel audio solution to the front panel audio header follow these steps 1 2 Observe the precautions in Before
3. FLFR Ar LA EACH ERRE SR AIR ESE Deutsch Als Teil von Intels Engagement fur den Umweltschutz hat das Unternehmen das Intel Produkt Recyclingprogramm implementiert das Einzelhandelskunden von Intel Markenprodukten erm glicht gebrauchte Produkte an ausgew hlte Standorte fur ordnungsgemabes Recycling zur ckzugeben Details zu diesem Programm einschlieBlich der darin eingeschlossenen Produkte verf gbaren Standorte Versandanweisungen Bedingungen usw finden Sie auf der http www intel com intel other ehs product ecolo Espafiol Como parte de su compromiso de responsabilidad medioambiental Intel ha implantado el programa de reciclaje de productos Intel que permite que los consumidores al detalle de los productos Intel devuelvan los productos usados en los lugares seleccionados para su correspondiente reciclado Consulte la http www intel com intel other ehs product ecolo para ver los detalles del programa que incluye los productos que abarca los lugares disponibles instrucciones de env o t rminos y condiciones etc Regulatory Compliance Francais Dans le cadre de son engagement pour la protection de l environnement Intel a mis en ceuvre le programme Intel Product Recycling Program Programme de recyclage des produits Intel pour permettre aux consommateurs de produits Intel de recycler les produits us s en les retournant des adresses sp cifi es Visitez la page Webhttp www intel com intel oth
4. Intel Desktop Board DG33FB Product Guide Hardware Monitoring and Fan Speed Control The features of the hardware monitoring and fan speed control include e Monitoring of power supply voltages to detect levels above and below acceptable values e Intel Quiet System Technology fan speed control delivering acoustically optimized thermal management NOTE Memory must be installed in the Channel A DIMM 0 socket to enable Intel Quiet System Technology e Fan speed controllers and sensors integrated into the ICH9DH e Thermal sensors in the processor GMCH and ICH9DH plus an onboard remote sensor e Thermally monitored closed loop fan control for all onboard fans that can adjust fan speed or switch the fans off as needed Chassis Intrusion The board supports a chassis security feature that detects if the chassis cover has been removed The security feature uses a mechanical switch on the chassis that can be connected to the chassis intrusion header on the Desktop Board See Figure 23 for the location of the chassis intrusion header Power Management Features Power management is implemented at several levels including e Software support through the Advanced Configuration and Power Interface ACPI e Hardware support Power connectors Fan headers LAN wake capabilities Instantly Available PC technology Suspend to RAM 5 V standby power indicator LED Wake from USB Wake from PS 2 keyboard mous
5. device For example do not connect an ATA hard drive as a slave to an ATAPI CD ROM drive For correct function of the cable e Observe the precautions in Before You Begin on page 25 e Attach the cable end with the single connector blue to the Intel Desktop Board Figure 21 A e Attach the cable end with the two closely spaced connectors gray and black to the drives Figure 21 B Installing and Replacing Desktop Board Components OM20007 Figure 21 Connecting the IDE Cable 43 Intel Desktop Board DG33FB Product Guide Connecting the Serial ATA SATA Cables SATA cables support the Serial ATA protocol Each cable can be used to connect a single SATA drive to the Desktop Board For correct cable function 44 LL 2 Observe the precautions in Before You Begin on page 25 Attach one end of the SATA cable to one of the SATA connectors on the board Figure 22 A Attach the other end of the SATA cable to the SATA drive Figure 22 B 0M20008 Figure 22 Connecting a Serial ATA Cable Installing and Replacing Desktop Board Components Connecting to the Internal Headers Before connecting cables to the internal headers observe the precautions in Before You Begin on page 25 Figure 23 shows the location of the internal headers D IEEE 1394a Key no pin Port1L 1 2 Ground 7 12V TPA2 28 Ground B TPA1 PortlR 3 4 Presence Port2R LS D Sensel Ret Sense Send
6. wiring and cables are components certified for the country or market where used Agency certification marks on the product are proof of certification Typical product certifications include In Europe The CE marking signifies compliance with all applicable European requirements If the chassis and other components are not properly CE marked a supplier s Declaration of Conformity statement to the European EMC directive and Low Voltage directive as applicable should be obtained Additionally other directives such as the Radio and Telecommunications Terminal Equipment R amp TTE directive may also apply depending on product features In the United States A certification mark by a Nationally Recognized Testing Laboratory NRTL such as UL CSA or ETL signifies compliance with safety requirements Wiring and cables must also be UL listed or recognized and suitable for the intended use The FCC Class B logo for home or office use signifies compliance with electromagnetic interference EMI requirements In Canada A nationally recognized certification mark such as CSA or cUL signifies compliance with safety requirements The Industry Canada statement at the front of this product guide demonstrates compliance with Canadian EMC regulations 75
7. Audience The Product Guide is intended for technically qualified personnel It is not intended for general audiences Use Only for Intended Applications All Intel Desktop Boards are evaluated as Information Technology Equipment I T E for use in personal computers PC for installation in homes offices schools computer rooms and similar locations The suitability of this product for other PC or embedded non PC applications or other environments such as medical industrial alarm systems test equipment etc may not be supported without further evaluation by Intel Document Organization The chapters in this Product Guide are arranged as follows 1 Desktop Board Features a summary of product features 2 Installing and Replacing Desktop Board Components instructions on how to install the Desktop Board and other hardware components 3 Updating the BIOS instructions on how to update the BIOS A Error Messages and Indicators information about BIOS error messages and beep codes B Regulatory Compliance safety and EMC regulations and product certifications Conventions The following conventions are used in this manual AN CAUTION Cautions warn the user about how to prevent damage to hardware or loss of data L NOTE Notes call attention to important information Intel Desktop Board DG33FB Product Guide Terminology The table below gives descriptions of some common terms used in the product guide Term Description GB
8. DG33FB Product Guide Product Certifications Board Level Certification Markings 74 Desktop Board DG33FB has the following product certification markings Table 17 Product Certification Markings Description Mark UL joint US Canada Recognized Component mark Includes adjacent UL file number for Intel Desktop Boards E210882 C US FCC Declaration of Conformity logo mark for Class B equipment Includes Intel name and DG33FB model designation TOS ama C Model Number CE mark Declaring compliance to European Union EU EMC directive 89 336 EEC and Low Voltage directive 73 23 EEC C Australian Communications Authority ACA C tick mark Includes adjacent Intel supplier code number N 232 Japan VCCI Voluntary Control Council for Interference mark S Korea MIC Ministry of Information and Communication mark 9 Includes adjacent MIC certification number CPU DG33FB MIC For information about MIC certification go to http support intel com support motherboards deskto Taiwan BSMI Bureau of Standards Metrology and Inspections mark Includes adjacent Intel company number D33025 Printed wiring board manufacturer s recognition mark Consists of a V 0 unique UL recognized manufacturer s logo along with a flammability rating solder side Regulatory Compliance Chassis and Component Certifications Ensure that the chassis and certain components such as the power supply peripheral drives
9. Gigabyte 1 073 741 824 bytes GHz Gigahertz one billion hertz KB Kilobyte 1024 bytes MB Megabyte 1 048 576 bytes Mbit Megabit 1 048 576 bits MHz Megahertz one million hertz Box Contents e Intel Desktop Board DG33FB e I O shield e One diskette drive cable e One ATA 66 100 cable e Two locking Serial ATA cables e Quick Reference e Configuration and battery caution statement labels e Intel Express Installer Driver and Software CD ROMs Contents 1 Desktop Board Features Supported Operating Systems ceeeeeeesseeeeeeennnme hh rre EEN EE EEN 10 Desktop Board COMPONEN mamaria vio 11 POCOS SOT curarlo rs cido pi asilo 13 METAN II S EE 13 Intel G33 Express Chipset IH me ee menses nr na nnannrnnnnnannaso 14 Intel G33 Graphics SUDSYSLOETI e xad d u Ke aaa 14 Te le BE e EE NEE 16 Legacy Input Output 1 0 Controller KEEN nennen nnne nnn nne 16 LAN SUS St WE 16 Roe LAN Connector EELDSu u uuu u a ecesac sees weet Ee 17 Hi Speed USB 2 0 SUDDOELU EE 18 EnnNaneca IDE TOESETOEG E 18 e a iElup m 18 EXD AN Ga ac anes 18 O AP e y yg TARA 18 Serial ATA and IDE Auto Configuration nemen 19 PCI and PCI Express Auto Confguration nennen nnn 19 See Le Ee E 19 Hardware Management Features EEN EEN enne haa nn aaa hn nn 19 Hardware Monitoring and Fan Speed Control 20 co
10. N ratio of 95 dB e Independent multi streaming 5 1 audio using the back panel audio connectors and stereo using the Intel High Definition front panel audio header Related Links Go to the following link or pages for more information about e Audio drivers and utilities http support intel com support motherboards deskto e Installing the front panel audio solution page 46 e The location of audio connectors Figure 24 on page 49 Legacy Input Output I O Controller The I O controller features the following e Low pin count LPC interface e One serial port interface via an onboard header e One diskette drive interface e Serial IRQ interface compatible with serialized IRQ support for PCI systems e PS 2 style mouse and keyboard interfaces e Intelligent power management including a programmable wake up event interface e PCI power management support LAN Subsystem The LAN subsystem includes e Intel ICHODH e Intel 82566DC Gigabit 10 100 1000 Mb s Ethernet LAN controller e RJ 45 LAN connector with integrated status LEDs The subsystem features e CSMA CD protocol engine e LAN connect interface between ICH9DH and the LAN controller e PCI bus power management Related Links Go to the following link for information about LAN software and drivers http support intel com support motherboards deskto 16 Desktop Board Features RJ 45 LAN Connector LEDs Two LEDs are built into the RJ 45 LAN connector located
11. You Begin on page 25 Turn off all peripheral devices connected to the computer Turn off the computer and disconnect the AC power cord Remove the cover Install a correctly keyed and shielded front panel audio cable Installing and Replacing Desktop Board Components Connecting to the Serial Port Header See Figure 23 C for the location of the serial port header Table 6 shows the pin assignments for the header Table 6 Serial Port Header Signal Names RTS 8 CTS Connecting to the Chassis Intrusion Header Figure 23 D on page 45 shows the location of the chassis intrusion header This header can be connected to a mechanical switch on the chassis to detect if the chassis cover is removed WO iui Uc Table 8 shows the pin assignments for the chassis intrusion header Table 7 Chassis Intrusion Header Description Intruder Ground Connecting to the Alternate Front Panel Power LED Header Figure 23 E shows the location of the alternate front panel power LED header Pins 1 and 3 of this header duplicate the signals on pins 2 and 4 of the front panel header If your chassis has a three pin power LED cable connect it to this header Table 8 shows the pin assignments for the alternate front panel header Table 8 Alternate Front Panel Power LED Header gt 47 Intel Desktop Board DG33FB Product Guide Connecting to the Front Panel Header Before connecting to the front panel header observe the precau
12. change the BIOS settings for the computer You can access the BIOS Setup program by pressing the F2 key after the Power On Self Test POST memory test begins and before the operating system boot begins This chapter tells you how to update the BIOS by either using the Intel Express BIOS Update utility or the Iflash Memory Update utility and how to recover the BIOS if an update fails Updating the BIOS with the Intel Express BIOS Update Utility With the Intel Express BIOS Update utility you can update the system BIOS while in the Windows environment The BIOS file is included in an automated update utility that combines the functionality of the Intel Flash Memory Update Utility and the ease of use of Windows based installation wizards To update the BIOS with the Intel Express BIOS Update utility 1 Go to the Intel World Wide Web site http support intel com support motherboards deskto 2 Navigate to the DG33FB page click view Latest BIOS updates and select the Express BIOS Update utility file 3 Download the file to your hard drive You can also save this file to a removable USB device This is useful if you are updating the BIOS for multiple identical systems 4 Close all other applications This step is required Your system will be rebooted at the last Express BIOS Update window 5 Double click the executable file from the location on your hard drive where it was saved This runs the update program 6 Follow
13. described here Failure to disconnect the power before you open the computer can result in personal injury or equipment damage Refer to your chassis manual for instructions on installing and removing the Desktop Board Figure 5 shows the location of the mounting screw holes for Desktop Board DG33FB Figure 5 Desktop Board DG33FB Mounting Screw Hole Locations 28 Installing and Replacing Desktop Board Components Installing and Removing a Processor Instructions on how to install the processor to the Desktop Board are given below Installing a Processor A CAUTION Before installing or removing the processor make sure the AC power has been removed by unplugging the power cord from the computer the standby power LED should not be lit see Figure 3 on page 23 Failure to do so could damage the processor and the board To install a processor follow these instructions 1 Observe the precautions in Before You Begin on page 25 2 Open the socket lever by pushing the lever down and away from the socket Figure 6 A and B 0M19997 Figure 6 Lift the Socket Lever 29 Intel Desktop Board DG33FB Product Guide 3 Lift the load plate Figure 7 A Do not touch the socket contacts Figure 7 B 0M19998 Figure 7 Lift the Load Plate 4 Remove the plastic protective socket cover from the load plate Figure 8 Do not discard the protective socket cover Always replace the socket cover if the processor is
14. disconnected to reach the DIMM sockets Replace the computer s cover and reconnect the AC power cord Installing and Replacing Desktop Board Components Installing and Removing a PCI Express x16 Card A CAUTION When installing a PCI Express x16 card on the Desktop Board ensure that the card is fully seated in the PCI Express x16 connector before you power on the system If the card is not fully seated in the PCI Express connector an electrical short may result across the PCI Express connector pins Depending on the over current protection of the power supply certain Desktop Board components and or traces may be damaged Installing a PCI Express x16 Card 1 Observe the precautions in Before You Begin on page 25 2 Place the card in the PCI Express x16 connector Figure 18 A and press down on the card until it is completely seated in the connector and the card retention notch on the card snaps into place around the retention mechanism pin on the connector 3 Secure the card s metal bracket to the chassis back panel with a screw Figure 18 B OM20005 Figure 18 Installing a PCI Express x16 Card 39 Intel Desktop Board DG33FB Product Guide Removing the PCI Express x16 Card Follow these instructions to remove the PCI Express x16 card from the connector 1 2 40 Observe the precautions in Before You Begin on page 25 Remove the screw Figure 19 A that secures the card s metal bracket to the ch
15. er i overensstemmelse med det europ iske direktiv 89 336 EEC amp 73 23 EEC Dutch Dit product is in navolging van de bepalingen van Europees Directief 89 336 EEC amp 73 23 EEC Eesti Antud toode vastab Euroopa direktiivides 89 336 EEC ja 73 23 EEC kehtestatud nouetele Suomi Tama tuote noudattaa EU direktiivin 89 336 EEC 73 23 EEC m r yksi Francais Ce produit est conforme aux exigences de la Directive Europ enne 89 336 EEC amp 73 23 EEC Deutsch Dieses Produkt entspricht den Bestimmungen der Europ ischen Richtlinie 89 336 EEC amp 73 23 EEC EAAnvika To napov npolov akoAou8 amp i ric iar amp gic Tov Eupwndikwv Odnyiwv 89 336 EOK kal 73 23 EOK Magyar E term k megfelel a 89 336 EEC s 73 23 EEC Eur pai Ir nyelv el r sainak Icelandic Pessi vara stenst regluger Evr pska Efnahags Bandalagsins numer 89 336 EEC amp 73 23 EEC Italiano Questo prodotto conforme alla Direttiva Europea 89 336 EEC amp 73 23 EEC Latvie u Sis produkts atbilst Eiropas Direktivu 89 336 EEC un 73 23 EEC noteikumiem Regulatory Compliance Lietuviu Sis produktas atitinka Europos direktyvu 89 336 EEC ir 73 23 EEC nuostatas Malti Dan il prodott hu konformi mal provvedimenti tad Direttivi Ewropej 89 336 EEC u 73 23 EEC Norsk Dette produktet er i henhold til bestemmelsene i det europeiske direktivet 89 336 EEC amp 73 23 EEC Polski Niniejszy produkt jest zgodny z postanowieniami Dyrektyw Unii Europejskie
16. pin processor fan header and one 4 pin and two 3 pin chassis fan headers LAN Wake Capabilities A CAUTION For LAN wake capabilities the 5 V standby line for the power supply must be capable of delivering adequate 5 V standby current Failure to provide adequate standby current when using this feature can damage the power supply LAN wakeup capabilities enable remote wake up of the computer through a network The LAN subsystem monitors network traffic and upon detecting a Magic Packet frame it asserts a wake up signal that powers up the computer 21 Intel Desktop Board DG33FB Product Guide Instantly Available PC Technology A CAUTIONS For Instantly Available PC technology the 5 V standby line for the power supply must be capable of delivering adequate 5 V standby current Failure to provide adequate standby current when using this feature can damage the power supply and or effect ACPI S3 sleep state functionality Power supplies used with this Desktop Board must be able to provide enough standby current to support the standard Instantly Available ACPI S3 sleep state configuration If the standby current necessary to support multiple wake events from the PCI and or USB buses exceeds power supply capacity the Desktop Board may lose register settings stored in memory Instantly Available PC technology enables the board to enter the ACPI S3 Suspend to RAM sleep state While in the S3 sleep state the computer will appear t
17. regulamenta es ambientais da regi o A CIARO ZNA IcHye pbi3bika BblOyxy K 3aMeHeHbl AKYMY IATAP HenpaBinbHara Tblirly AKYMY IATapbI rlaBiHHbI Na MarubiMacui nepenrpauoyBauua Ma36a na a ag cTapbix aKyYMy IATapay narp36Ha 3r04Ha 3 MACHOBbIM 3aKkaHagJayCcTBaM ria 3Kasnorii UPOZORNINI V p pad v m ny baterie za nespr vn druh m e doj t k v buchu Je li to mo n baterie by m ly b t recyklov ny Baterie je t eba zlikvidovat v souladu s m stn mi p edpisy o ivotn m prost ed 55 Intel Desktop Board DG33FB Product Guide AN A Ipooox Ynm pxel KivOuvoc yia Ekpn n OS NEPINTWON nou n uriarapia avrikaraoraosi ano pia Aav aopevou rU nou Ori unarapiec 0a np amp riel va GVGKUKAWVOVTAI OTav K TI TETOIO Elval OuvaTo H ari ppiuyr rov xprjoiuornoinu vov unarapiwv NPENE va YIVETAI OUuqQova LE TOUG KATA TONO ri pIBaAAOVTIKOUG KAVOVIOUOUC VIGYAZAT Ha a telepet nem a megfelel t pusu telepre cser li az felrobbanhat A telepeket lehet s g szerint ujra kell hasznositani A haszn lt telepeket a helyi k rnyezetv delmi eldirasoknak megfelel en kell kiselejtezni A ag 56 FIERRO E MAREA BAOEK U ES JHI D un REI CHAS BHU 4 2 JEL C lt ESL SFH EO s HAAS EST HE lei C lt F S UA AWAS Risiko letupan wujud Jika bateri digantikan dengan Jenis yang tidak betul Bateri sepatutnya dikitar semula jika boleh Pelupusan bateri terpakai mestilah mematuhi peraturan al
18. removed from the socket 0M19999 Figure 8 Remove the Protective Socket Cover 30 Installing and Replacing Desktop Board Components 5 Remove the processor from the protective processor cover Hold the processor only at the edges being careful not to touch the bottom of the processor see Figure 9 Do not discard the protective processor cover Always replace the processor cover if the processor is removed from the socket OM20000 Figure 9 Remove the Processor from the Protective Processor Cover 6 Hold the processor with your thumb and index fingers oriented as shown in Figure 10 Make sure your fingers align to the socket cutouts Figure 10 A Align notches Figure 10 B with the socket Figure 10 C Lower the processor straight down without tilting or sliding it OM20001 Figure 10 Install the Processor 31 Intel Desktop Board DG33FB Product Guide 7 Pressing down on the load plate Figure 11 A close and engage the socket lever Figure 11 B OM20002 Figure 11 Close the Load Plate Installing the Processor Fan Heat Sink Desktop Board DG33FB has mounting holes for a processor fan heat sink For instructions on how to attach the processor fan heat sink to the Desktop Board refer to the boxed processor manual 32 Installing and Replacing Desktop Board Components Connecting the Processor Fan Heat Sink Cable Connect the processor fan heat sink cable to the 4 pin processor fan header s
19. requires the use of a USB peripheral that supports Wake from USB USB bus activity wakes the computer from an ACPI S3 state Wake from PS 2 Keyboard Mouse PS 2 keyboard mouse activity wakes the computer from an ACPI S3 state PMEZ Signal Wake up Support When the PME signal on the PCI bus is asserted the computer wakes from an ACPI S3 S4 or S5 state WAKEZ Signal Wake up Support When the WAKE signal on the PCI Express bus is asserted the computer wakes from an ACPI S2 S3 S4 or S5 state 23 Intel Desktop Board DG33FB Product Guide ENERGY STAR Qualified In 2007 the US Department of Energy and the US Environmental Protection Agency revised the ENERGY STAR requirements Intel worked directly with these two governmental agencies to define the new requirements Currently Intel Desktop Boards meet the new ENERGY STAR requirements For information about the ENERGY STAR specifications see http www3 intel com cd channel reseller asmo na eng 337748 htm Speaker A speaker is mounted on the Desktop Board The speaker provides audible error code beep code information during the Power On Self Test POST Battery A battery on the Desktop Board keeps the values in CMOS RAM and the clock current when the computer is turned off Go to page 54 for instructions on how to replace the battery Real Time Clock The Desktop Board has a time of day clock and 100 year calendar The battery on the Desktop Board keeps the clo
20. to the latest production release regardless of the operating system installed on the computer s hard drive and without the need to remove the BIOS configuration jumper It requires a blank CD R a read writeable CD drive and software capable of uncompressing and writing the ISO image file to CD The image uses ISOLINUX bootloader and automatically launches a script to upgrade the BIOS via the Iflash utility Updating the BIOS AN CAUTION Do not interrupt the process or the system may not function properly Follow these instructions to upgrade the BIOS using the ISO Image BIOS file 1 Download the ISO Image BIOS file 2 Using software capable of uncompressing and writing an ISO image file to CD burn the data to a blank CD pal NOTE Copying the ISO Image BIOS file to CD will not work The completed CD should contain multiple files and a directory 3 Insert the CD that was created in the CD ROM drive of the computer to be upgraded and boot the system 4 When the Press ENTER to continue booting from CD ROM prompt appears press the Enter key The system will boot from the hard drive if no key is pressed within 15 seconds 5 Atthe Welcome to the Intel Desktop Board BIOS Upgrade CD ROM page press any key to confirm the BIOS upgrade operation 6 Wait for the BIOS upgrade process to complete A CAUTION DO NOT POWER DOWN YOUR COMPUTER before the update is complete The update may take up to 5 minutes Updating the BIOS
21. with the Iflash Memory Update Utility With the Iflash Memory update utility you can update the system BIOS from a bootable CD ROM bootable USB flash drive or other bootable USB media The utility available on the Intel World Wide Web site provides a simple method for creating a bootable CD ROM that will automatically update your BIOS The Iflash BIOS update files can also be extracted locally to your hard drive and copied to a bootable USB flash drive or other bootable USB media The Iflash Memory update utility allows you to e Update the BIOS and Intel Management Engine in flash memory e Update the language section of the BIOS g NOTE Review the instructions distributed with the update utility before attempting a BIOS update 61 Intel Desktop Board DG33FB Product Guide A CAUTION Do not interrupt the process or the system may not function properly 1 Uncompress the BIOS update file and copy the BIO file IFLASH EXE and ITK file optional to a bootable USB flash drive or other bootable USB media 2 Configure the BIOS or use the F10 option during POST to boot to the USB device 3 Manually run the IFLASH EXE file from the USB device and manually update the BIOS Recovering the BIOS It is unlikely that anything will interrupt the BIOS update however if an interruption occurs the BIOS could be damaged Due to BIOS size and recovery requirements a CD R with the BIO file in the root directory will be required Related
22. AIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO SALE AND OR USE OF INTEL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE MERCHANTABILITY OR INFRINGEMENT OF ANY PATENT COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT Intel products are not intended for use in medical life saving or life sustaining applications Intel may make changes to specifications and product descriptions at any time without notice Desktop Board DG33FB may contain design defects or errors known as errata which may cause the product to deviate from published specifications Current characterized errata are available on request Contact your local Intel sales office or your distributor to obtain the latest specifications and before placing your product order Copies of documents which have an ordering number and are referenced in this document or other Intel literature may be obtained from Intel Corporation by going to the World Wide Web site at http www intel com or by calling 1 800 548 4725 Intel Pentium and Celeron are registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries Other names and brands may be claimed as the property of others Copyright 2007 Intel Corporation All rights reserved Preface This Product Guide gives information about board layout component installation BIOS update and regulatory requirements for Intel Desktop Board DG33FB Intended
23. Di gt Description PCI bus connector 3 Auxiliary chassis fan header 4 pin PCI Express x1 connector 3 PCI Express x1 connector 2 PCI bus connector 2 Front panel audio header PCI bus connector 1 PCI Express x1 connector 1 Speaker PCI Express x16 connector Back panel connectors 12 V processor core voltage connector 2 x 2 pin Rear chassis fan header 3 pin Processor socket Processor fan header 4 pin Serial header Main power connector 2 x 12 pin Diskette drive connector DDR2 DIMM 0 sockets DDR2 DIMM 1 sockets Chassis intrusion header Battery Front chassis fan header 3 pin BIOS configuration jumper block Alternate front panel power LED header Front panel header Serial ATA connectors 4 IDE connector High speed USB 2 0 headers 3 IEEE 1394a header Related Links 12 Go to the following links for more information about e Desktop Board DG33FB http www intel com design motherbd http support intel com support motherboards deskto e Supported processors http www intel com go findCPU e Audio software and utilities http www intel com design motherbd e LAN software and drivers http www intel com design motherbd Desktop Board Features Processor AN CAUTION Failure to use an appropriate power supply and or not connecting the 12 V 2 x 2 pin power connector to the Desktop Board may result in damage to the board or the system may not function properly Desktop Board DG33FB supports a
24. Gb technology e Up to 8 0 GB utilizing 1 Gb technology Related Links Go to the following links or pages for more information about e SDRAM specifications http www intel com technology memor e Installing memory page 34 in Chapter 2 e Tested memory http www cmtlabs com mbsearch asp or http www intel com products motherboard index htm iid HMPAGE Header 2 P roduct MB e PC Serial Presence Detect Specification http www intel com technology memory ddr specs ddai8c32 64 128x72aga pdf Intel G33 Express Chipset The Intel G33 Express Chipset consists of the following devices e Intel G33 Express Chipset Graphics and Memory Controller Hub GMCH with Direct Media Interface DMI e Intel 82801IH I O Controller Hub ICH9DH with DMI Related Links Go to the following link for more information about the Intel G33 Express Chipset http developer intel com design nav pcserver htm Intel G33 Graphics Subsystem The Intel G33 Express Chipset contains two separate mutually exclusive graphics options Either the integrated Intel Graphics Media Accelerator 3100 GMA 3100 graphics controller is used or a PCI Express x16 add in card can be used When a PCI Express x16 add in card is installed the Intel GMA 3100 graphics controller is disabled The Intel GMA 3100 features the following e 400 MHz core frequency e High quality texture engine DX9 0c and OpenGL 1 4 compliant Hardware Pixel Shader 2 0 Vertex Shader
25. I Express graphics cards Audio e 6 channel 5 1 onboard subsystem featuring Intel High Definition Audio interface RealTek ALC888 audio codec Expansion e One PCI Express x16 connector Capabilities e Three PCI Express x1 connectors e Three PCI connectors Legacy I O Support Legacy I O Controller that provides One diskette drive interface One serial port header PS 2 keyboard and mouse ports Peripheral e Up to 12 USB 2 0 ports Interfaces Six ports routed to the back panel Six ports routed to three USB headers e Up to two IEEE 1394a ports One port routed to the back panel One port routed to an IEEE 1394a header e Four Serial ATA SATA channels 3 0 Gb s via the ICH9DH e One IDE interface with ATA 66 100 support two devices continued Intel Desktop Board DG33FB Product Guide Table 1 Feature Summary continued BIOS e Intel Platform Innovation Framework for extensible firmware interface e 8 Mbit symmetrical flash memory device e Support for SMBIOS e Intel Rapid BIOS Boot e Intel Express BIOS Update Power Management e Support for Advanced Configuration and Power Interface ACPI e Suspend to RAM STR e Wake on USB PCI Express PS 2 LAN and front panel e ENERGY STAR qualified desktop board Hardware Hardware monitor with Management e Three fan sensing inputs used to monitor fan activity e Intel Quiet System Technology fan speed control e Voltage sensing to detect out of range valu
26. Links For more information about updating the Intel Desktop Board BIOS or recovering from a BIOS update failure go to http support intel com support motherboards desktop sb CS 022312 htm 62 A Error Messages and Indicators Desktop Board DG33FB reports POST errors in two ways e By sounding a beep code e By displaying an error message on the monitor BIOS Beep Codes The BIOS also issues a beep code one long tone followed by two short tones during POST if the video configuration fails a faulty video card or no card installed or if an external ROM module does not properly checksum to zero Table 12 lists the BIOS codes Table 12 Beep Codes Beep Description 3 No memory Siren Processor overheat on reboot BIOS Error Messages When a recoverable error occurs during the POST the BIOS displays an error message describing the problem Table 13 gives an explanation of the BIOS error messages Table 13 BIOS Error Messages Error Message PROCESSOR THERMAL TRIP ERROR MULTI BIT ECC ERROR SINGLE BIT ECC ERROR CMOS BATTERY ERROR CMOS CHECKSUM ERROR CMOS TIMER ERROR MEMORY SIZE DECREASE ERROR INTRUDER DETECTION ERROR SPD TOLER ERROR MEM OPTIMAL ERROR Explanation Processor was previously shutdown due to a thermal event overheating The firmware has detected that a Multi Bit ECC Error occurred The firmware has detected that a Single Bit ECC Error occurred The firmware has detected that a CMOS battery
27. Model 2 0 14 Desktop Board Features e 3D Graphics Rendering enhancements 1 6 dual texture GigaPixel s maximum fill rate 16 bit and 32 bit color Maximum 3D supported resolution of 1600 x 1200 x 32 at 85 Hz Vertex cache e Video Software DVD at 30 fps full screen Adaptive deinterlacing Dynamic Video Memory Technology DVMT support up to 256 MB e Display NOTE Intel TV Wizard utility step by step setup help for TVs and displays Up to 2048 x 1536 at 75 Hz refresh QXGA DVI specification 1 0 compliant Dual independent display options with digital display Hardware color cursor support High Definition Content Protection HDCP version 1 1 support DDC2B compliant interface with Advanced Digital Display 2 card or Media Expansion Card ADD2 MEC support for TV out TV in and DVI digital display connections Supports flat panels up to 2048 x 1536 at 75 Hz when in dual channel mode or digital CRT HDTV at 1920 x 1080 at 60 Hz with ADD2 MEC A minimum of 512 MB of system memory is required in order for the Intel GMA 3100 integrated graphics controller to operate properly 15 Intel Desktop Board DG33FB Product Guide Audio Subsystem The onboard audio subsystem consists of the following e Intel ICH9DH I O controller hub e RealTek ALC888 audio codec e Back panel audio connectors e Intel High Definition audio front panel audio header The audio subsystem supports the following features e A signal to noise S
28. Utility eene Updating the BIOS with the ISO Image BIOS Update File or the Iflash Memory CGE Bici in ep ETT Obtaining the BIOS Update FNS soc c ei eb ER qevo alo Fort rcd t Re pni Updating the BIOS with the ISO Image BIOS Update File Updating the BIOS with the Iflash Memory Update Utility RECOVEHING the BOS A Error Messages and Indicators BLOS BESO Re e EE BIOS deele Vi Contents B Regulatory Compliance Sal y RegulgtollS sxszexesxestuicrdi nina AA ai ana VEA UEFA FR UN eae 65 Place Battery MAKING a AAA 65 European Union Declaration of Conformity Gtatement cnn 66 Product Ecology Statements AAA AAA 68 Recycling Considerations SAA 68 Lead Free Desktop Boardi EE 70 EMC Regulation Sita AA 72 Ensure Electromagnetic Compatibility EMC Compliance eese 73 Product CertilicaltlOFiS EE 74 Board Level Certification Markings cesses nnne nnnm naya rr 74 Chassis and Component Certifications EEN EEN EEN 75 Figures ke Desktop Board DGS5FB Components asia 11 Z LAN Connector EE 17 3 Location of the Standby Power Indicator r r r r r r 23 4 Installing the TOSCA EE EE 27 5 Desktop Board DG33FB Mounting Screw Hole Locations 28 6 jEUUThesS ockeb LOVER aus TII UE o Ee dE dee 29 Fie SEITE RIS Eoad Platea 30 8 Remove the P
29. akildiginda patlama riski vardir Piller m mk n oldugunda geri d n st r lmelidir Kullan lm piller yerel evre yasalar na uygun olarak at lmal d r OCTOPOTA BUKOPUCTOBynTe 6arapei nMpaBunbHoro Tuny iHaKkule ICHYBATUMe DA3A4K Bubyxy AKLO MOXJINBO BUKOPUCTaHi 6arapel cria yruniayBarTH Yrunisauis BUKOPpucTaHux 6aTapeu Mae 6yTH BUKOHaHa 3ri4Ho MICLIEBUX HODM LUO DeTy IIOIOTb OXODOHy JOBKINNA UPOZORNENI V pripad vym ny baterie za nespravny druh muze dojit k vybuchu Je li to mozn baterie by m ly byt recyklovany Baterie je treba zlikvidovat v souladu s mistnimi predpisy o ivotn m prost ed ETTEVAATUST Kui patarei asendatakse uue ebasobivat t pi patareiga v ib tekkida plahvatusoht T hjad patareid tuleb v imaluse korral viia vastavasse kogumispunkti T hjade patareide raviskamisel tuleb j rgida kohalikke keskkonnakaitse alaseid reegleid FIGYELMEZTET S Ha az elemet nem a megfelel tipusura cser li felrobbanhat Az elemeket lehet s g szerint jra kell hasznos tani A haszn lt elemeket a helyi k rnyezetv delmi el r soknak megfelel en kell kiselejtezni UZMANIBU Past v eksplozijas risks ja baterijas tiek nomain tas ar nepareiza veida baterij m Ja iesp jams baterijas vajadz tu nodot attiec gos pie em anas punktos Bateriju izme anai atkritumos j notiek saskana ar viet jiem vides aizsardz bas noteikumiem DEMESIO Naudojant netinkamo tipo baterijas jrenginys gali s
30. am sekitar tempatan OSTRZEZENIE Istnieje niebezpieczenstwo wybuchu w przypadku zastosowania niew a ciwego typu baterii Zu yte baterie nale y w miar mo liwo ci utylizowa zgodnie z odpowiednimi przepisami ochrony rodowiska PRECAUTIE Risc de explozie daca bateria este inlocuita cu un tip de baterie necorespunzator Bateriile trebuie reciclate daca este posibil Depozitarea bateriilor uzate trebuie sa respecte reglementarile locale privind protectia mediului BHHMAHME Mpu ucnonb30BaHunu 6arapen uecoorBercrByrioujero rura cyujecrByer PUCK ee B3pbIBa BaTapeu JOJMKHbI ObITb yTHJIH34DOBaHbI MO BOSMOXHOCTM Yrusu3ayna 6arapeli JOJDKHa MPOBOAUTCA DO MPaBUNIAM COOTBeTCTByIOLL HM M CTHbIM TDEOOBAHUAM UPOZORNENIE Ak bat riu vymen te za nespr vny typ hroz nebezpecenstvo jej vybuchu Bat rie by sa mali podla moZnosti vZdy recyklovat Likvid cia pouZitych bat ri sa mus vykon vat v sulade s miestnymi predpismi na ochranu Zivotn ho prostredia A Installing and Replacing Desktop Board Components POZOR Zamenjava baterije z baterijo drugacnega tipa lahko povzroci eksplozijo Ce je mogoce baterije reciklirajte Rabljene baterije zavrzite v skladu z lokalnimi okoljevarstvenimi predpisi AX dn au AN AN gt gt b b pP ejonasssifiaYufiaaimu guuiueunasleissuniumnunmdf hutild aruquuataas d 1988 AIT Yuuuemmasisuesasiilutimmnngzzaeiusrucua dauzaosvias amp u UYARI Yanlis t rde pil t
31. annel Memory Configuration with Two DIMMs 34 Installing and Replacing Desktop Board Components If additional memory is to be used install another matched pair of DIMMs in DIMM 1 black in channels A and B see Figure 14 DIMM O Channel A DIMM 1 DIMM 0 Channel B DIMM 1 OM20022 Figure 14 Dual Channel Memory Configuration with Four DIMMs Three DIMMs If you want to use three DIMMs in a dual channel configuration install a matched pair of DIMMs equal in speed and size in DIMM O blue and DIMM 1 black of channel A Install a DIMM equal in speed and total size of the DIMMs installed in channel A in either DIMM 0 or DIMM 1 of channel B see Figure 15 DIMM Channel A DIMM 1 DIMM O Channel B DIMM 1 Freres OM20023 Figure 15 Dual Channel Memory Configuration with Three DIMMs p NOTE All other memory configurations will result in single channel memory operation 35 Intel Desktop Board DG33FB Product Guide Installing DIMMs To make sure you have the correct DIMM place it on the illustration of the DDR2 DIMM in Figure 16 All the notches should match with the DDR2 DIMM DDR2 cm 1 2 3 4 9 6 7i 8 9 10 11 12 13 OM20003 Figure 16 Use DDR2 DIMMs 36 Installing and Replacing Desktop Board Components gs NOTE Memory must be installed in the Channel A DIMM 0 socket to enable Intel Quiet System Technology To install a DIMM follow these steps 1 Observe the precautions in Before Yo
32. assis back panel Push the card ejector lever down using the tip of a pencil or similar tool Figure 19 B in the notch This will release the card from the connector C Pull the card straight up A OM20006 Figure 19 Removing a PCI Express x16 Card Installing and Replacing Desktop Board Components Connecting the Diskette Drive Cable The diskette drive cable can be used to connect a single diskette drive to the Desktop Board For correct function of the cable e Observe the precautions in Before You Begin on page 25 e Attach the cable end labeled P1 to the diskette drive connector on the Intel Desktop Board Figure 20 A e Attach the cable end labeled P2 to the diskette drive Figure 20 B OM20012 Figure 20 Connecting the Diskette Drive Cable 41 Intel Desktop Board DG33FB Product Guide Connecting the IDE Cable gt 42 The IDE cable can be used to connect two IDE drives to the Desktop Board The cable supports the ATA 66 100 transfer protocol Figure 21 shows the correct installation of the cable NOTES ATA 66 100 compatible cables are backward compatible with drives using slower IDE transfer protocols If an ATA 66 100 disk drive and a disk drive using any other IDE transfer protocol are attached to the same cable the maximum transfer rate between the drives may be reduced to that of the slowest drive Do not connect an ATA device as a slave on the same IDE cable as an ATAPI master
33. ck current when the computer is turned off 24 2 Installing and Replacing Desktop Board Components This chapter tells you how to e Install the I O shield e Install and remove the Desktop Board e Install and remove a processor e Install and remove memory e Install and remove a PCI Express x16 card e Connet the diskette drive cable e Connect the IDE and Serial ATA cables e Connect to the internal headers e Connect to the flexible audio system e Connect chassis fan and power supply cables e Set the BIOS configuration jumper e Clear passwords e Replace the battery Before You Begin A CAUTIONS The procedures in this chapter assume familiarity with the general terminology associated with personal computers and with the safety practices and regulatory compliance required for using and modifying electronic equipment Disconnect the computer from its power source and from any telecommunications links networks or modems before performing any of the procedures described in this chapter Failure to disconnect power telecommunications links networks or modems before you open the computer or perform any procedures can result in personal injury or equipment damage Some circuitry on the board can continue to operate even though the front panel power button is off Follow these guidelines before you begin e Always follow the steps in each procedure in the correct order e Set up a log to record information about your compute
34. e Power Management Event signal PME wakeup support WAKE signal wake up support e ENERGY STAR qualified ACPI ACPI gives the operating system direct control over the power management and Plug and Play functions of a computer The use of ACPI with the Desktop Board requires an operating system that provides full ACPI support 20 Desktop Board Features Hardware Support Power Connectors ATX12V compliant power supplies can turn off the computer power through system control When an ACPI enabled computer receives the correct command the power supply removes all non standby voltages When resuming from an AC power failure the computer returns to the power state it was in before power was interrupted either on or off The computer s response can be set by using the Last Power State feature in the BIOS Setup program s Boot menu The Desktop Board has two power connectors See Figure 26 on page 51 for the location of the power connectors Fan Headers The function operation of the fans is as follows e The fans are on when the computer is in the ACPI SO state e The fans are off when the computer is in the ACPI S3 S4 or S5 state e Each fan header is wired to a tachometer input of the hardware monitoring and control device e All fan headers support closed loop fan control that can adjust the fan speed or switch the fan on or off as needed e All fan headers have a 12 V DC connection The Desktop Board has a 4
35. e battery The clock is accurate to 13 minutes year at 25 9C with 3 3 VSB applied When the voltage drops below a certain level the BIOS Setup program settings stored in CMOS RAM for example the date and time might not be accurate Replace the battery with an equivalent one Figure 28 on page 58 shows the location of the battery CAUTION Risk of explosion if the battery is replaced with an incorrect type Batteries should be recycled where possible Disposal of used batteries must be in accordance with local environmental regulations PRECAUTION Risque d explosion si la pile usag e est remplac e par une pile de type incorrect Les piles usag es doivent tre recycl es dans la mesure du possible La mise au rebut des piles usag es doit respecter les r glementations locales en vigueur en mati re de protection de l environnement FORHOLDSREGEL Eksplosionsfare hvis batteriet erstattes med et batteri af en forkert type Batterier bgr om muligt genbruges Bortskaffelse af brugte batterier bgr foreg i overensstemmelse med g ldende milj lovgivning OBS Det kan oppst eksplosjonsfare hvis batteriet skiftes ut med feil type Brukte batterier b r kastes i henhold til gjeldende milj lovgivning A A A Installing and Replacing Desktop Board Components VIKTIGT Risk f r explosion om batteriet ers tts med felaktig batterityp Batterier ska kasseras enligt de lokala milj v rdsbest mmelserna VARO Ra
36. ee Figure 12 A fan with a 4 pin connector as shown in Figure 12 A is recommended however a fan with a 3 pin connector Figure 12 B can be used However since a fan with a 3 pin connector cannot use the onboard fan control the fan will always operate at full speed aa Sra OM20020 Figure 12 Connecting the Processor Fan Heat Sink Cable to the Processor Fan Header 33 Intel Desktop Board DG33FB Product Guide Removing the Processor For instructions on how to remove the processor fan heat sink and processor refer to the processor installation manual Installing and Removing Memory ga NOTE To be fully compliant with all applicable Intel SDRAM memory specifications the board requires DIMMs that support the Serial Presence Detect SPD data structure Desktop board DG33FB has four 240 pin DDR2 DIMM sockets arranged as DIMM 0 and DIMM 1 in both Channel A and Channel B j NOTE Regardless of the memory configuration used dual or single channel Channel A DIMM 0 must always be populated This is a requirement of the ICH9DH Manageability Engine feature Guidelines for Dual Channel Memory Configuration Before installing DIMMs read and follow these guidelines for dual channel configuration Two or Four DIMMs Install a matched pair of DIMMs equal in speed and size see Figure 13 in DIMM O blue of channels A and B ONTA Channel A DIMM 1 TED Channel B DIMM 1 DELE OM20021 Figure 13 Dual Ch
37. er ehs product ecolo pour en savoir plus sur ce programme savoir les produits concern s les adresses disponibles les instructions d exp dition les conditions g n rales etc H ZB 4YTIVCIS Eat RPE SUO ECU UM AJA UTIL J gt FRATERNO URREA US DLE CITTA S42 fv 7T 8 US 0 JH72Lt 3E ig t UTC HRN oh IAS MUDA CH HMBC COJO LOR AMI sd http www intel com in tel other ehs product ecology 24 TES Malay Sebagai sebahagian daripada komitmennya terhadap tanggungjawab persekitaran Intel telah melaksanakan Program Kitar Semula Produk untuk membenarkan pengguna pengguna runcit produk jenama Intel memulangkan produk terguna ke lokasi lokasi terpilih untuk dikitarkan semula dengan betul Sila rujuk http www intel com intel other ehs product ecology untuk mendapatkan butir butir program ini termasuklah skop produk yang dirangkumi lokasi lokasi tersedia arahan penghantaran terma amp syarat dsb Portuguese Como parte deste compromisso com o respeito ao ambiente a Intel implementou o Programa de Reciclagem de Produtos para que os consumidores finais possam enviar produtos Intel usados para locais selecionados onde esses produtos sao reciclados de maneira adequada Consulte o site http www intel com intel other ehs product_ ecology em Ingl s para obter os detalhes sobre este programa inclusive o escopo dos produtos cobertos os locais dispon veis as instru es de envio os termos e condi es etc Russia
38. eral Edition Requirements International Place Battery Marking There is insufficient space on this Desktop Board to provide instructions for replacing and disposing of the Lithium ion coin cell battery For system safety certification the statement below or an equivalent statement is required to be permanently and legibly marked on the chassis near the battery A CAUTION Risk of explosion if the battery is replaced with an incorrect type Batteries should be recycled where possible Disposal of used batteries must be in accordance with local environmental regulations Related Links For information about replacing the battery go to page 54 65 Intel Desktop Board DG33FB Product Guide European Union Declaration of Conformity Statement 66 We Intel Corporation declare under our sole responsibility that the product Intel Desktop Board DG33FB is in conformity with all applicable essential requirements necessary for CE marking following the provisions of the European Council Directive 89 336 EEC EMC Directive and Council Directive 73 23 EEC Safety Low Voltage Directive The product is properly CE marked demonstrating this conformity and is for distribution within all member states of the EU with no restrictions L This product follows the provisions of the European Directives 89 336 EEC and 73 23 EEC CeStina Tento vyrobek odpov d pozadavk m evropskych sm rnic 89 336 EEC a 73 23 EEC Dansk Dette produkt
39. es LAN Support Intel 82566DC Gigabit 10 100 1000 Mb s Ethernet LAN controller Related Links For more information about Desktop Board DG33FB including the Technical Product Specification TPS BIOS updates and device drivers go to http support intel com support motherboards deskto Supported Operating Systems 10 The Desktop Board supports the following operating systems e Microsoft Windows Vista Ultimate e Microsoft Windows Vista Enterprise e Microsoft Windows Vista Business e Microsoft Windows Vista Home Premium e Microsoft Windows Vista Home Basic e Microsoft Windows Vista Ultimate 64 bit edition e Microsoft Windows Vista Enterprise 64 bit edition e Microsoft Windows Vista Business 64 bit edition e Microsoft Windows Vista Home Premium 64 bit edition e Microsoft Windows Vista Home Basic 64 bit edition e Microsoft Windows XP Media Center Edition 2005 e Microsoft Windows XP Professional e Microsoft Windows XP Professional x64 Edition e Microsoft Windows XP Home Desktop Board Features Desktop Board Components Figure 1 shows the approximate location of the major components on Desktop Board DG33FB L M pe ini N DD 0 E p OM19995 Figure 1 Desktop Board DG33FB Components 11 Intel Desktop Board DG33FB Product Guide Table 2 Desktop Board DG33FB Components r D E e P N lt gt x lt c d v A O VP O z z K T 0 m m o o Di gt g GO Uu g GO
40. failure occurred The firmware has detected that a CMOS Checksum Error occurred The firmware has detected that the system date time has not been set The firmware has detected that the system memory has decreased The system chassis was opened SERIAL PRESENCE DETECT SPD device data missing or inconclusive Properly programmed SPD device data is required for reliable operation The installed amount of memory in Channel A is not equal to the amount of memory in Channel B Maximum memory performance is achieved with equal amounts of memory installed in each channel 63 Intel Desktop Board DG33FB Product Guide 64 B Regulatory Compliance This appendix contains the following regulatory compliance information for Desktop Board DG33FB e Safety regulations e European Union Declaration of Conformity statement e Product Ecology statements e Electromagnetic Compatibility EMC regulations e Product certifications Safety Regulations Desktop Board DG33FB complies with the safety regulations stated in Table 14 when correctly installed in a compatible host system Table 14 Safety Regulations Regulation Title UL 60950 1 2003 Information Technology Equipment Safety Part 1 General CSA C22 2 No 60950 1 03 Requirements USA and Canada EN 60950 1 2002 Information Technology Equipment Safety Part 1 General Requirements European Union IEC 60950 1 2001 First Information Technology Equipment Safety Part 1 Gen
41. features that restrict whether the BIOS Setup program can be accessed and who can boot the computer A supervisor password and a user password can be set for the BIOS Setup and for booting the computer with the following restrictions e The supervisor password gives unrestricted access to view and change all Setup options If only the supervisor password is set pressing Enter at the password prompt of Setup gives the user restricted access to Setup e If both the supervisor and user passwords are set you must enter either the supervisor password or the user password to access Setup Setup options are then available for viewing and changing depending on whether the supervisor or user password was entered e Setting a user password restricts who can boot the computer The password prompt is displayed before the computer is booted If only the supervisor password is set the computer boots without asking for a password If both passwords are set you can enter either password to boot the computer Related Links For instructions on resetting the password see Clearing Passwords on page 53 Hardware Management Features The hardware management features of Desktop Board DG33FB enable the board to be compatible with the Wired for Management WfM specification The board has several hardware management features including the following e Fan speed monitoring and control e Thermal and voltage monitoring e Chassis intrusion detection 19
42. gure 26 Connecting Power Supply Cables 1 Observe the precautions in Before You Begin on page 25 2 Connect the main power supply cable to the 2 x 12 pin connector 3 Connect the 12 V processor core voltage power supply cable to the 2 x 2 pin connector 51 Intel Desktop Board DG33FB Product Guide Setting the BIOS Configuration Jumper NOTE Always turn off the power and unplug the power cord from the computer before moving the jumper Moving the jumper with the power on may result in unreliable computer operation Figure 27 shows the location of the Desktop Board s BIOS configuration jumper block OM20013 Figure 27 Location of the BIOS Configuration Jumper Block The three pin BIOS jumper block enables all board configurations to be done in the BIOS Setup program Table 11 shows the jumper settings for the BIOS Setup program modes 52 Installing and Replacing Desktop Board Components Table 11 Jumper Settings for the BIOS Setup Program Modes Jumper Setting Mode Description Normal default 1 2 The BIOS uses the current configuration and passwords for booting Configure 2 3 After the Power On Self Test POST runs the BIOS displays the Maintenance Menu Use this menu to clear passwords Recovery None The BIOS recovers data in the event of a failed BIOS update Clearing Passwords This procedure assumes that the board is installed in the computer and the configuration jumper block is set to n
43. ing to the Flexible Audio System After installing the RealTek audio driver from the Intel Express Installer CD ROM the multi channel audio feature can be enabled Figure 24 shows the back panel audio connectors The default connector assignments are shown in the table OM20018 Item Description A Line In B Line Out C Mic In Figure 24 Back Panel Audio Connectors L NOTE The back panel line out connector is designed to power either headphones or amplified speakers only Poor audio quality may occur if passive non amplified speakers are connected to this output 49 Intel Desktop Board DG33FB Product Guide Connecting Chassis Fan and Power Supply Cables Connecting Chassis Fan Cables Connect chassis fan cables to the 3 pin and 4 pin chassis fan headers on the Desktop Board Figure 25 shows the location of the chassis fan headers 0M20010 Figure 25 Location of the Chassis Fan Headers 50 Installing and Replacing Desktop Board Components Connecting Power Supply Cables AN CAUTION Failure to use an appropriate power supply and or not connecting the 12 V 2 x 2 pin power connector to the Desktop Board may result in damage to the board or the system may not function properly The 2 x 12 pin main power connector on the Desktop Board is backwards compatible with ATX12V power supplies with 2 x 10 connectors Figure 26 shows the location of the Desktop Board power connectors pa OM20011 Fi
44. j 89 336 EWG i 73 23 EWG Portuguese Este produto cumpre com as normas da Diretiva Europ ia 89 336 EEC amp 73 23 EEC Espanol Este producto cumple con las normas del Directivo Europeo 89 336 EEC amp 73 23 EEC Slovensky Tento produkt je v sulade s ustanoveniami eur pskych direktiv 89 336 EEC a 73 23 EEC Slovenscina Izdelek je skladen z dolocbami evropskih direktiv 89 336 EGS in 73 23 EGS Svenska Denna produkt har tillverkats i enlighet med EG direktiv 89 336 EEC amp 73 23 EEC T rk e Bu r n Avrupa Birligi nin 89 336 EEC ve 73 23 EEC y nergelerine uyar 67 Intel Desktop Board DG33FB Product Guide Product Ecology Statements The following information is provided to address worldwide product ecology concerns and regulations Recycling Considerations 68 As part of its commitment to environmental responsibility Intel has implemented the Intel Product Recycling Program to allow retail consumers of Intel s branded products to return used products to select locations for proper recycling Please consult http www intel com intel other ehs product ecolo for the details of this program including the scope of covered products available locations shipping instructions terms and conditions etc rc VEN EA SST EZR TORRES Intel Product Recycling Program OR RR m CT DL FORDE SE m RP A VR l t EE RE AE AA B xe E TR Ed es PED ARIES A ines http www intel com intel other ehs product ecolo J RAL RUS EET
45. j gee EE 20 Power Management Features EE 20 POP p E 20 Hardware SUDDOLE ee 21 Power ge ul e e LEE EN Fan Headers E 21 LAN Wake Capablanca aia on 21 Instantly Available PC Technology 22 5 V Standby Power Indicator LED ocooocccccccccccnnnnncnnnrnnn mnn 22 Vu Ol E D cr E EO 23 Wake from PS 2 KeybDoard MOUSE ccccseeceuceeuseceeueeneuceuueeteuueueenteugentenes 23 PME Signal Wake up Gupport mnes 23 WAKE7 Signal Wake up Support gege oec oii e ERO ER RC TR RD 23 ENERGY STAR QUAM OO EE 24 EE EE o O EE T 24 See HO 24 zsiaiEa Ee erect 24 2 Installing and Replacing Desktop Board Components Balore VOU BCO q mM 25 Installation Precauti nS EE 26 Prevent Power Supply Overload mission 26 Observe Safety and Regulatory Requirements 26 Installing bd RE E H e EE 27 Installing and Removing the Desktop Board 28 Intel Desktop Board DG33FB Product Guide Installing and Removilg d PEOCeSSOEJ dme von gea ci ne be pa ees dt bed reo Rows ai sos Installing a PEFOESSSOLP saspe X a a le pe atas en ea Vo eec Ca f eb aot t e t d ete Installing the Processor Fan Heat Sink a s Connecting the Processor Fan Heat Sink Cable ceeeen nnnm nnn EECHER d Am Ee Installing and REMOVING MerolblV su
46. jahdysvaara jos pariston tyyppi on v r Paristot on kierratettavd jos se on mahdollista K ytetyt paristot on h vitett v paikallisten ymp rist m r ysten mukaisesti VORSICHT Bei falschem Einsetzen einer neuen Batterie besteht Explosionsgefahr Die Batterie darf nur durch denselben oder einen entsprechenden vom Hersteller empfohlenen Batterietyp ersetzt werden Entsorgen Sie verbrauchte Batterien den Anweisungen des Herstellers entsprechend AVVERTIMENTO Esiste il pericolo di un esplosione se la pila non viene sostituita in modo corretto Utilizzare solo pile uguali o di tipo equivalente a quelle consigliate dal produttore Per disfarsi delle pile usate seguire le istruzioni del produttore PRECAUCI N Existe peligro de explosi n si la pila no se cambia de forma adecuada Utilice solamente pilas iguales o del mismo tipo que las recomendadas por el fabricante del equipo Para deshacerse de las pilas usadas siga igualmente las instrucciones del fabricante WAARSCHUWING Er bestaat ontploffingsgevaar als de batterij wordt vervangen door een onjuist type batterij Batterijen moeten zoveel mogelijk worden gerecycled Houd u bij het weggooien van gebruikte batterijen aan de plaatselijke milieuwetgeving ATEN O Haver risco de explos o se a bateria for substitu da por um tipo de bateria incorreto As baterias devem ser recicladas nos locais apropriados A elimina o de baterias usadas deve ser feita de acordo com as
47. n B kauecrBe uacra cBOMX O653aT6e IBCTB K okpyxatrouiel cpene B Intel cosnaHa nporpaMMa yTunu3auun npoaykuunn Intel Product Recycling Program ana npeAocTaB IeHMs KOHeUHBIM NONb3OBaTENAM Mapok nmpoAaykunn Intel BOSMOXHOCTM BO3BDpaTa MCHOJIb3yeMOM NPOAYKUMNM B CNeLMaNU3upOBaHHble NYHKTbI ANA J10JDKHOM yTUNU3AL un Noxanyucta o6patutecb Ha Be6 ca T www intel com intel other ehs product ecology 3a nHcopMaunehn o6 3TOU nporpaMMe MpuHuMaembIX riIponykTax Mecrax mpuema MHCTpyKUMAX OD ornpaBke MONOKEHNAX N YCNOBNAX M T R 69 Intel Desktop Board DG33FB Product Guide T rkce Intel cevre sorumluluguna bagimliliginin bir pargasi olarak perakende t keticilerin Intel markali kullanilmis r nlerini belirlenmis merkezlere iade edip uygun sekilde geri d n st rmesini ama layan Intel r nleri Geri D n m Program n uygulamaya koymustur Bu programin r n kapsami r n iade merkezleri nakliye talimatlari kayitlar ve sartlar v s dahil b t n ayrintilarini grenmek icin l tfen http www intel com intel other ehs product ecology web sayfas na gidin Lead Free Desktop Board 70 This Desktop Board is a European Union Restriction of Hazardous Substances EU RoHS compliant product EU RoHS restricts the use of six materials One of the six restricted materials is lead Intel Desktop Board DP35DP is lead free although certain discrete components used on the board contain a small amount of lead which is necessary fo
48. n Intel processor in the LGA775 package Processors are not included with the Desktop Board and must be purchased separately The processor connects to the Desktop Board through the LGA775 socket Related Links Go to the following page or link for more information about e Instructions on installing or upgrading the processor page 29 in Chapter 2 e Supported processors for Desktop Board DG33FB http www intel com go find CPU Main Memory NOTE To be fully compliant with all applicable Intel SDRAM memory specifications the board should be populated with DIMMs that support the Serial Presence Detect SPD data structure If your memory modules do not support SPD you will see a notification to this effect on the screen at power up The BIOS will attempt to configure the memory controller for normal operation The Desktop Board supports the dual or single channel memory configurations defined below e Four 240 pin Double Data Rate 2 DDR2 SDRAM Dual Inline Memory Module DIMM connectors with gold plated contacts e Support for Unbuffered non registered single or double sided DIMMs Non ECC DDR2 memory DIMM Type and Timings listed below Type Timing DDR2 800 5 5 5 or 6 6 6 only DDR2 667 5 5 5 only Serial Presence Detect SPD memory only 13 Intel Desktop Board DG33FB Product Guide Memory configurations listed below e Up to 2 0 GB utilizing 256 Mb technology e Up to 4 0 GB utilizing 512 Mb or 1
49. n determined to be 10 years 71 Intel Desktop Board DG33FB Product Guide EMC Regulations Desktop Board DG33FB complies with the EMC regulations stated in Table 16 when correctly installed in a compatible host system 72 Table 16 EMC Regulations Regulation FCC Class B ICES 003 Class B EN55022 1998 Class B EN55024 1998 AS NZS CISPR22 Class B CISPR 22 3 Edition Class B CISPR 24 1997 VCCI Class B Title Title 47 of the Code of Federal Regulations Parts 2 and 15 Subpart B Radio Frequency Devices USA Interference Causing Equipment Standard Digital Apparatus Canada Limits and methods of measurement of Radio Interference Characteristics of Information Technology Equipment European Union Information Technology Equipment Immunity Characteristics Limits and methods of measurement European Union Australian Communications Authority Standard for Electromagnetic Compatibility Australia and New Zealand Limits and methods of measurement of Radio Disturbance Characteristics of Information Technology Equipment International Information Technology Equipment Immunity Characteristics Limits and Methods of Measurement International Voluntary Control for Interference by Information Technology Equipment Japan Japanese Kanji statement translation This is a Class B product based on the standard of the Voluntary Control Council for Interference from Information Tech
50. nology Equipment VCCI If this is used near a radio or television receiver in a domestic environment it may cause radio interference Install and use the equipment according to the instruction manual COREL spurge sam PROS AEREAS VCCI DEX CHOC 2 2 Z B TASR ase C d CORBIS TXEEIRIR C EFHd 2 HRjCUCU EZ CORBPAIYAPTLEV a EBRO LT tA inat SERRE tica PIR SRA IES CIEL UHRUSRUREUXCT U Regulatory Compliance Korean Class B statement translation This is household equipment that is certified to comply with EMC requirements You may use this equipment in residential environments and other non residential environments Ensure Electromagnetic Compatibility EMC Compliance Before computer integration make sure that the power supply and other modules or peripherals as applicable have passed Class B EMC testing and are marked accordingly Pay close attention to the following when reading the installation instructions for the host chassis power supply and other modules Product certifications or lack of certifications External I O cable shielding and filtering Mounting grounding and bonding requirements Keying connectors when mating the wrong connectors could be hazardous If the power supply and other modules or peripherals as applicable are not Class B EMC compliant before integration then EMC testing may be required on a representative sample of the newly completed computer 73 Intel Desktop Board
51. o be off If the computer has a dual colored power LED on the front panel the sleep state is indicated by the LED turning amber When signaled by a wake up device or event the computer quickly returns to its last known awake state The Desktop Board supports the PCI Bus Power Management Interface Specification Add in cards that support this specification can participate in power management and can be used to wake the computer 5 V Standby Power Indicator LED A 22 CAUTION If the AC power has been switched off and the standby power indicator is still lit disconnect the power cord before installing or removing any devices connected to the board Failure to do so could damage the board and any attached devices The Desktop Board s standby power indicator shown in Figure 3 is lit when there is standby power still present on the board even when the computer appears to be off For example when this LED is lit standby power is still present at the memory module Sockets and the PCI bus connectors Desktop Board Features OM20016 Figure 3 Location of the Standby Power Indicator Related Links For more information on standby current requirements for the Desktop Board refer to the Technical Product Specification by going to the following link finding the product and selecting Product Documentation from the left hand menu http support intel com support motherboards deskto Wake from USB gs NOTE Wake from USB
52. ociated modules If you do not follow these instructions and the instructions provided by the chassis and module suppliers you increase safety risk and the possibility of noncompliance with regional laws and regulations If the instructions for the chassis are inconsistent with these instructions or the instructions for associated modules contact the supplier s technical support to find out how you can ensure that your computer meets safety and regulatory requirements Related Links 26 For information about regulatory compliance go to Appendix B on page 65 Installing and Replacing Desktop Board Components Installing the I O Shield The Desktop Board comes with an I O shield When installed in the chassis the shield blocks radio frequency transmissions protects internal components from dust and foreign objects and promotes correct airflow within the chassis Install the I O shield before installing the Desktop Board in the chassis Place the shield inside the chassis as shown in Figure 4 Press the shield into place so that it fits tightly and securely If the shield does not fit obtain a properly sized shield from the chassis supplier OM20017 Figure 4 Installing the I O Shield 27 Intel Desktop Board DG33FB Product Guide Installing and Removing the Desktop Board AN CAUTION Only qualified technical personnel should do this procedure Disconnect the computer from its power source before performing the procedures
53. on the back panel see Figure 2 These LEDs indicate the status of the LAN A B OM20018 Figure 2 LAN Connector LEDs Table 3 describes the LED states when the board is powered up and the LAN subsystem is operating Table 3 LAN Connector LEDs LED LED Color LED State Indicates A Green Of LAN link is not established On LAN link is established LI m LAN activity is occurring mE e NN 100 Mb s data rate 17 Intel Desktop Board DG33FB Product Guide Hi Speed USB 2 0 Support The Desktop Board supports up to 12 USB 2 0 ports six ports routed to the back panel and six ports routed to three internal headers via the ICH9DH USB 2 0 ports are backward compatible with USB 1 1 devices USB 1 1 devices will function normally at USB 1 1 speeds USB 2 0 support requires both an operating system and drivers that fully support USB 2 0 transfer rates Disabling Hi Speed USB in the BIOS reverts all USB 2 0 ports to USB 1 1 operation This may be required to accommodate operating systems that do not support USB 2 0 Enhanced IDE Interface The board s IDE interface handles the exchange of information between the processor and peripheral devices such as hard disk drives and CD ROM drives The interface supports e Up to two IDE devices such as hard drives e ATAPI style devices such as CD ROM drives e Older PIO Mode devices e Ultra DMA 33 and ATA 66 100 protocols Serial ATA The Desktop Board supports fou
54. ormal mode 1 2 Observe the precautions in Before You Begin on page 25 Turn off all peripheral devices connected to the computer Turn off the computer Disconnect the computer s power cord from the AC power source wall outlet or power adapter Remove the computer cover Find the configuration jumper block see Figure 27 Place the jumper on pins 2 3 as shown below Replace the cover plug in the computer turn on the computer and allow it to boot The computer starts the Setup program Setup displays the Maintenance menu Use the arrow keys to select Clear Passwords Press Enter and Setup displays a pop up screen requesting that you confirm clearing the password Select Yes and press Enter Setup displays the maintenance menu again Press F10 to save the current values and exit Setup 53 Intel Desktop Board DG33FB Product Guide 10 Turn off the computer Disconnect the computer s power cord from the AC power source 11 Remove the computer cover 12 To restore normal operation place the jumper on pins 1 2 as shown below 13 Replace the cover plug in the computer and turn on the computer Replacing the Battery 54 A coin cell battery CR2032 powers the real time clock and CMOS memory When the computer is not plugged into a wall socket the battery has an estimated life of three years When the computer is plugged in the standby current from the power supply extends the life of th
55. progti Kai tik imanoma baterijas reikia naudoti pakartotinai Panaudotas baterijas i mesti b tina pagal vietinius aplinkos apsaugos nuostatus 57 Intel Desktop Board DG33FB Product Guide AN 58 ATTENZJONI Riskju ta splu joni jekk il batterija tinbidel b tip ta batterija mhux korrett Il batteriji g andhom ji u riciklati fejn hu possibbli Ir rimi ta batteriji uzati g andu jsir skond ir regolamenti ambjentali lokali OSTRZE ENIE Ryzyko wybuchu w przypadku wymiany na baterie niew a ciwego typu W miar mo liwo ci baterie nale y podda recyklingowi Zuzytych baterii nale y pozbywa si zgodnie z lokalnie obowi zuj cymi przepisami w zakresie ochrony rodowiska To replace the battery follow these steps 1 2 v Observe the precautions in Before You Begin see page 25 Turn off all peripheral devices connected to the computer Disconnect the computer s power cord from the AC power source wall outlet or power adapter Remove the computer cover Locate the battery on the board see Figure 28 With a medium flat bladed screwdriver gently pry the battery free from its connector Note the orientation of the and on the battery Install the new battery in the connector orienting the and correctly Replace the computer cover OM20015 Figure 28 Removing the Battery 3 Updating the BIOS The BIOS Setup program can be used to view and
56. r such as model serial numbers installed options and configuration information e Electrostatic discharge ESD can damage components Perform the procedures described in this chapter only at an ESD workstation using an antistatic wrist strap and a conductive foam pad If such a station is not available you can provide some ESD protection by wearing an antistatic wrist strap and attaching it to a metal part of the computer chassis 25 Intel Desktop Board DG33FB Product Guide Installation Precautions When you install and test the Intel Desktop Board observe all warnings and cautions in the installation instructions To avoid injury be careful of e Sharp pins on connectors e Sharp pins on printed circuit assemblies e Rough edges and sharp corners on the chassis e Hot components such as processors voltage regulators and heat sinks e Damage to wires that could cause a short circuit Observe all warnings and cautions that instruct you to refer computer servicing to qualified technical personnel Prevent Power Supply Overload Do not overload the power supply output To avoid overloading the power supply make sure that the calculated total current loads of all the modules within the computer is less than the output current rating of each of the power supplies output circuits Observe Safety and Regulatory Requirements Read and adhere the instructions in this section and the instructions supplied with the chassis and ass
57. r Serial ATA channels 3 0 Gb s via ICH9DH connecting one device per channel Expandability For system expansion the Desktop Board provides the following expansion slots e One PCI Express x16 connector e Three PCI Express x1 connectors e Three PCI bus connectors BIOS The BIOS provides the Power On Self Test POST the BIOS Setup program the PCI PCI Express and IDE auto configuration utilities and the video BIOS The BIOS is stored in the Serial Peripheral Interface SPI Flash device The BIOS can be updated by following the instructions on page 59 in Chapter 3 18 Desktop Board Features Serial ATA and IDE Auto Configuration If you install a Serial ATA or IDE device such as a hard drive in your computer the auto configuration utility in the BIOS automatically detects and configures the device for your computer You do not need to run the BIOS Setup program after installing a Serial ATA or IDE device You can override the auto configuration options by specifying manual configuration in the BIOS Setup program PCI and PCI Express Auto Configuration If you install a PCI PCI Express add in card in your computer the PCI PCI Express auto configuration utility in the BIOS automatically detects and configures the resources IRQs DMA channels and I O space for that add in card You do not need to run the BIOS Setup program after you install a PCI PCI Express add in card Security Passwords The BIOS includes security
58. r component performance and or reliability This Desktop Board is referred to as Lead free second level interconnect The board substrate and the solder connections from the board to the components second level connections are all lead free China bans the same substances and has the same limits as EU RoHS however it requires different product marking and controlled substance information The required mark shows the Environmental Friendly Usage Period EFUP The EFUP is defined as the number of years for which controlled listed substances will not leak or chemically deteriorate while in the product Table 15 shows the lead free board markings as they appear on the board and accompanying collateral Regulatory Compliance Table 15 Lead Free Board Markings Description Mark Lead Free 2 Level Interconnect This symbol is used to identify electrical and electronic assemblies and components in which the lead Pb concentration level in the Desktop Board substrate and the solder connections from or the board to the components second level interconnect is not greater than 0 1 by weight 1000 ppm 2nd evel Interconnect 2nd lvl Intct China RoHS Environmentally Friendly Use Period Logo This an example of the symbol used on Intel Desktop Boards and associated collateral The color of the mark may vary depending upon the application The Environmental Friendly Usage Period EFUP for Intel Desktop Boards has bee
59. rotective Socket Cover EEN EEN REENEN EEN emen 30 9 Remove the Processor from the Protective Processor Cover 31 L0 Install the PROCESS OL sororibus Eed T E 31 close the boda TEE 32 12 Connecting the Processor Fan Heat Sink Cable to the Processor Fan Header 33 13 Dual Channel Memory Configuration with Two DIMMSs 34 14 Dual Channel Memory Configuration with Four DIMNMe Hn 35 15 Dual Channel Memory Configuration with Three DIMMS nnn nn 35 I6 Use DORZ BEE 36 Z e Ee ie te E WR EE 37 19 Installiig d PCI Express 16 CAFO u Du year exert o Rae ed awe is VH CEN VAR RO EAE CR 39 I9 Removilig g PEL Express X16 Card uctor bte dique Dot ded A 40 20 Connecting the Diskette Drive Cable eeeeeeeeeeern m mmm 41 2Zl Cohneclnu the IDE CODI EE 43 22 Connecting d Serial ATA e EE 44 25 Internal Hee Sra ida 45 24 Back Panel Audio WE e ln ege SA AAA AS 49 25 Location of the Chassis Fan Header ae EEN rc cnc 50 26 Connecting Power SUPDIV el 51 27 Location of the BIOS Configuration Jumper Block 52 20 Removing The Battery nc A 58 Vil Intel Desktop Board DG33FB Product Guide Tables Is Reature o gl EE 9 2 Desktop Boarda DGs3sFB COMPONENTS ua 12 S JEAN Connector RE 17 4 IEEE 15943 Signal Header NaMe S u k u VEA S OU ya ER RO OUR ER CA EVER SO Eh EAD 46 5 Front Panel Audio Header Signal Name
60. s for Intel High Definition Audio 46 6 Serial Port Header Signal NEIES cssc pP EFE REERERREET4RR EA PIX REG PPEOPEEPYR CUN CY FPES 47 Ta Chassis INCEUSION Ee EE 47 8 Alternate Front Panel Power LED Header EEN EEN nnn nnn 47 ds Fonte Patel Te TEE 48 10 USB 2 0 Header Signal Names ina 48 11 Jumper Settings for the BIOS Setup Program Modes 53 12 BED de 63 5 BIOS Error Messages ls 63 14 EC eg Te EE 65 TS bead Free Board Mark Sa pr DIPSA PPSVUIE PPP PE 71 Jo EME Regulation S EE 72 Ez Product Certification Markiana Aida 74 viii 1 Desktop Board Features This chapter briefly describes the features of Intel Desktop Board DG33FB Table 1 summarizes the major features of the Desktop Board Table 1 Feature Summary Form Factor ATX 320 04 millimeters 11 60 inches x 243 84 millimeters 9 60 inches Processor Support for an Intel processor in the LGA775 package Main Memory e Four 240 pin DDR2 1 8 V only SDRAM Dual Inline Memory Module DIMM sockets e 800 667 MHz single or dual channel DDR2 SDRAM interface e Support for up to 8 GB of system memory Chipset Intel G33 Express Chipset consisting of e ntel G33 Express Chipset Graphics and Memory Controller Hub GMCH e Intel 82801IH I O Controller Hub ICH9DH Graphics e Intel G33 Express Chipset with Intel Graphics Media Accelerator 3100 Intel GMA 3100 e One PCI Express x16 connector supporting PC
61. s u ug rx EA A Essa a acl Sid Guidelines for Dual Channel Memory Configuration Re ger FOUPIDIMIMS EE Three DIMN EE IASTalina eu IC LEE REMOVING PRI EE Installing and Removing a PCI Express x16 Card Installing a PGEEXpFess LO Cara ui A Removing the PCT Express X16 Cara EE Connecting the Diskette Drive Cable EEN EEN EEN EEN EEN EEN EEN Connecting the IDE Cables a Connecting the Serial ATA SATA Cables susan Connecting to the Internal Headers KEEN EEN EEN EEN EEN rr Connecting to the IEEE 1394a Header EEN cnn rra rr Installing a Front Panel Audio Solution for Intel High Definition Audio Connecting to the Serial Port Header ENN KEEN EEN EEN rr Connecting to the Chassis Intrusion Header ENNEN nn Connecting to the Alternate Front Panel Power LED Header Connecting to the Front Panel Header eee nmm nnn Connecting to the USB 2 0 Headere ae EEN EEN EEN nnn Connecting to the Flexible Audio System EEN nnnm mnm Connecting Chassis Fan and Power Supply Cables essere nemen Connecting Chassis Fan Cables uuu u y u ee EE eege Connecting Power Supply Cables s EEN E EEN EEN mnn Setting the BIOS Configuration Jumper ee clearmg Passwords m aet cu ve ub m baut tat ia imet diea uan wayqu dcos cae ui dan 3 Updating the BIOS Updating the BIOS with the Intel Express BIOS Update
62. the instructions provided in the dialog boxes to complete the BIOS update 59 Intel Desktop Board DG33FB Product Guide Updating the BIOS with the ISO Image BIOS Update File or the Iflash Memory Update Utility You can use the information in this section to update the BIOS using either the Iflash Memory Update Utility or the ISO Image BIOS update file Obtaining the BIOS Update File You can update to a new version of the BIOS by using the ISO Image BIOS update file recommended or Iflash BIOS update file The ISO Image BIOS update file is a standardized image of a bootable CD ROM that can be used to create a bootable CD that will update the BIOS The Iflash BIOS update file is a compressed file that contains the files you need to update the BIOS The Iflash BIOS update file contains e New BIOS file including the Intel Management Engine Firmware Image e Intel Integrator Toolkit Configuration File optional e Intel Flash Memory Update Utility You can obtain either of these files through your computer supplier or by navigating to the Desktop Board DG33FB page on the Intel World Wide Web site at http support intel com support motherboards deskto Navigate to the DG33FB page click view Latest BIOS updates and select the ISO Image BIOS Update or Iflash BIOS Update utility file Updating the BIOS with the ISO Image BIOS Update File 60 The ISO Image BIOS update allows for the update of an Intel Desktop Board BIOS
63. the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and the receiver e Connect the equipment to an outlet on a circuit other than the one to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Any changes or modifications to the equipment not expressly approved by Intel Corporation could void the user s authority to operate the equipment Tested to comply with FCC standards for home or office use Canadian Department of Communications Compliance Statement This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications Le pr sent appareil numerique n met pas de bruits radio lectriques d passant les limites applicables aux appareils num riques de la classe B prescrites dans le R glement sur le broullage radio lectrique dict par le minist re des Communications du Canada Disclaimer INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH INTEL PRODUCTS NO LICENSE EXPRESS OR IMPLIED BY ESTOPPEL OR OTHERWISE TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT EXCEPT AS PROVIDED IN INTEL S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS INTEL ASSUMES NO LIABILITY WHATSOEVER AND INTEL DISCL
64. tions in Before You Begin on page 25 See Figure 23 F for the location of the multi colored front panel header Table 9 shows the pin assignments for the front panel header Table 9 Front Panel Header Pin Description In Out Pin Description In Out Hard Drive Activity LED Power LED Hard disk LED pull up to 5 V Out 2 Front panel green LED out Hard disk active LED Out 4 Front panel yellow LED out Reset Switch On Off Switch 5 Ground Power switch I 7 Reset switch In 8 Ground Power Not Connected 9 Power Out 10 No pin Connecting to the USB 2 0 Headers Before connecting to the USB 2 0 headers observe the precautions in Before You Begin on page 25 See Figure 23 G for the location of the three USB 2 0 headers Table 10 shows the pin assignments for each USB 2 0 header Each USB header can be used to connect two USB devices Table 10 USB 2 0 Header Signal Names USB Port A USB Port B Pin Signal Name Pin Signal Name 1 Power 5 V 3 D E D 5 Dr L D 7 Ground 8 1 Ground 9 Key 10 No Connection Note USB ports may be assigned as needed L NOTE Computer systems that have an unshielded cable attached to a USB port might not meet FCC Class B requirements even if no device or a low speed USB device is attached to the cable Use a shielded cable that meets the requirements for a full speed USB device 48 Installing and Replacing Desktop Board Components Connect
65. u Begin on page 25 2 Turn off all peripheral devices connected to the computer Turn off the computer and disconnect the AC power cord 3 Remove the computer s cover and locate the DIMM sockets see Figure 17 G G G OG uu OM20004 Figure 17 Installing a DIMM 4 Make sure the clips at either end of the DIMM socket s are pushed outward to the open position 5 Holding the DIMM by the edges remove it from its anti static package 6 Position the DIMM above the socket Align the small notch at the bottom edge of the DIMM with the keys in the socket see inset in Figure 17 37 Intel Desktop Board DG33FB Product Guide 7 8 9 Insert the bottom edge of the DIMM into the socket When the DIMM is inserted push down on the top edge of the DIMM until the retaining clips snap into place Make sure the clips are firmly in place Replace the computer s cover and reconnect the AC power cord Removing DIMMs To remove a DIMM follow these steps 38 ae DI E Observe the precautions in Before You Begin on page 25 Turn off all peripheral devices connected to the computer Turn off the computer Remove the AC power cord from the computer Remove the computer s cover Gently spread the retaining clips at each end of the DIMM socket The DIMM pops out of the socket Hold the DIMM by the edges lift it away from the socket and store it in an anti static package Reinstall and reconnect any parts you removed or

Download Pdf Manuals

Related Search

Related Contents

  Partner Version - IP Office Info  Descargar  点検校正依頼書 (le_check)  Gouvernement du Canada  

Copyright © All rights reserved. Failed to retrieve file