Home

Intel ATC6430M User's Manual

1. Setup The system will boot without password but access to Setup requires correct password 22 ATC6430M Mainboard Chapter 3 Award BIOS Setup OS SelectforDRAM gt 64MB This item allows you to access the memory that is over 64MB in OS 2 The choice Non OS2 OS2 HDD S M A R T Capability Select Enabled if your Hard disk supports S M A R T Safe Monitoring Analysis and Reporting Technology function Report No FDD For WIN 95 Set this item to Yes BIOS will report FDD to Win95 If in standard CMOS setup set Drive A to none and set this item to Yes inside Win95 My Computer and File manager Disk A will show Removable Disk A 23 Chapter 3 Award RIOS Setun ATC6430M Mainboard 3 2 3 ADVANCED CHIPSET FEATURES This screen controls the setting for the chipset on the mainboard This chipset manages bus speeds and access to system memory resources CMOS Setup Utility Copyright 1984 1998 Award Software Advanced Chipset Features SDRAM CAS Latency Time SDRAM Cycle Time Tras Trc SDRAM RAS to CAS Delay SDRAM RAS Precharge Time System BIOS Cacheable Menu Level gt Video BIOS Cacheable Memory Hole At 15M 16M Disabled Delay Transaction Enabled On Chip Video Window Size 64MB Onboard Display Cache Setting CAS Latency 3 Paging Mode Control Close RAS to CAS Override By CAS LT RAS Timing low RAS Precharge Timing low Tle Move Enter Select PU PD Value
2. shutdown the computer in the Shut Down Windows of Windows 95 98 Then the system power will be off directly and stay at the stand by status If you want to restart the system just press the power switch button Note If you are going to leave your system idle for several days we suggest you use hardware power off to shut down your system To locate PS ON header please see Page A Quick Jumper amp Connector Setting Chapter 1 System Features ATC 6430M Mainboard 1 3 5 Modem Ring On With Modem Ring On function the computer can wake up by remote signal through a connected modem This function enables users to access their computer data from anywhere in the world Users have to enable Power On by Ring in Power Management Setup of the AWARD BIOS setup screens 1 3 6 SB Link Sideband Signals In order to migrate the legacy Sound Blaster compatible audio to the PCI bus EMU8008 incorporates a pair of SB Link request grant sideband signals PCPCIR EQN and PCPCIGNTN to interface to the PCI bus SB Link is a mechanism that was defined and developed by Intel as a docking solution which allows ISA slots to exist in docking stations connected to desktop PC PCI bus SB Link 2x3 sideband header sound will also has a 2x3 header and a cable SB Link REQ GND SIRQ GNTHA4T GND ATC6430M Mainboard Chapter 1 System Features 1 3 7 Ultra DMA 66 Cable optional Ultra DMA 66 cable 40 pin connector amp
3. 80 line cable is packaged while utilizing FW82801AA chip which supports both UDMA 33 amp UDMA 66 on the mainboard In other words Ultra DMA 33 cable is only used with FW82801AB chip And the Ultra DMA 66 color coded connectors are shown as bellow Blue to Mainboard Grey to Slave Black to IDE Peripheral Master INF Dannharal 1 3 8 Wake On LAN The remote Wake On LAN WOL mode of operation is a mechanism that uses Advanced Micro Device Magic Packet technology to power on a sleeping workstation on the network This mechanism is accomplished when the LAN card receives a specific packet of information called a Magic Packet addressed to the node on the network For additional protection Secure ON is an optional security feature that can be added to the Magic Packet that requires a password to power on the sleeping workstation When LAN card is in remote Wake On LAN mode main system power can be shut down leaving power only for the LAN card and auxiliary power recondition The LAN card performs no network activities while in the remote Wake On LAN mode of operation It only monitors the network for receipt of a Magic Packet If a Magic Packet is addressed to the LAN card on the network the LAN card wake up the system If the Secure ON feature has been enabled the password added to the Magic Packet is also verified prior to waking up the system You should select two kinds of PCI Ethernet cards with WOL function One is Intel and the ot
4. Boot Device Priority The choices Floppy LS ZIP HDD SCSI CDROM Disabled Swap Floppy Drive If the system has two floppy drives choose Enabled to assign the physical drive B to logical drive A and vice versa Boot Up Floppy Seek Enabled will test floppy drives and determine whether they have 40 or 80 tracks Boot Up NumLock Status This allows you to determine the default state of the numeric keypad By default the system boots up with NumLock on Keypad is for numeric keys Keypad is for arrow keys Gate A20 Option This entry allows you to select how the gate A20 is handled The gate A20 is a device used to address memory above 1 MB If Normal keyboard is controlled by a pin in keyboard controller If Fast it is controlled by chipset Typematic Rate Setting Keystrokes repeat at a rate determined by the keyboard controller When Enabled the typematic rate and typematic delay can be selected Typematic Rate Chars Sec When the typematic rate is enabled this item will appear to allow you to select the key repeat rate 6 means 6 characters per second Typematic Delay Msec When the typematic rate is enabled this item will appear to allow you to set the delay time before key strokes begin to repeat 250 250 msec 500 750 1000 Security Option This category allows you to limit access to the system and Setup or just to Setup Options Password is then required every time the system boots
5. F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail safe defaults F7 Optimized Defaults 24 ATC6430M Mainboard Chapter 3 Award BIOS Setup SDRAM CAS Latency Time When synchronous DRAM is installed the number of clock cycles of CAS latency depends on the DRAM timing The choices 2 3 2 gives faster performance and 3 gives more stable performance SDRAM Cycle Time Tras Trc Select the number of SCLKs for an access cycle 5 7 gives faster performance and 6 8 gives more stable performance SDRAM RAS to CAS Delay This field lets you insert a timing delay between the CAS and RAS strobe signals used when DRAM is written to read from or refreshed 2 gives faster performance and 3 gives more stable performance This field applies only when synchronous DRAM is installed in the system SDRAM RAS Prechage Time If an insufficient number of cycles is allowed for the RAS to accumulate its charge before DRAM refresh the refresh may be incomplete and the DRAM may fail to retain data This field applies only when synchronous DRAM is installed in the system System BIOS Cacheable Selecting Enabled allows the caching of the system BIOS ROM area resulting in better system performance However if any program writes to this memory area a system error may result Video BIOS Cacheable Selecting Enabled allows the caching of the video BIOS ROM area resulting in better system performance However if any program
6. Full or Half On Board Parallel Port Let user select IRQ for parallel port When Disabled the parallel port will be disabled Parallel Port Mode Let user select Parallel Port SPP EPP ECP ECP EPP ECP Mode Use DMA Select a DMA channel for the port Choices are 3 1 PWRON After PWR Fail Allows you to choose Off On former Status Game Port Address Midi Port Address The IO address of Game Port Midi Port If Midi Port is fixed the item Midi Port IRQ will appear for setting CIR Port Address Allows you to fix the Consumer Infrared Device Port Address If fixed the item CIR Port IRQ will appear for setting 29 Chapter 3_Award BIOS Setup ATC6430M Mainboard 3 2 5 POWER MANAGEMENT SETUP This screen controls the green features of this mainboard CMOS Setup Utility Copyright 1984 1998 Award Software Power Management Setup ACPI function Enabled Item Help Power Management User Define Video Off Method DPMS Video Off In Suspend Yes Menu Level gt Suspend Type Stop Grant MODEM Use IRQ 3 Suspend Mode Disabled HDD Power Down Disabled Soft Off by PWRBTN Instant Off PCI PME Function Disabled Power On by Ring Enabled CPU Thermal Throttling 50 0 Resume by Alarm Disabled Reload Global Timer Events Primary IDE 0 Disabled Primary IDE 1 Disabled Secondary IDE 0 Disabled Secondary IDE 1 Disabled FDD COM LPT Port Disab PCI P
7. and Slow gives more stable performance 26 ATC6430M Mainhoard Chanter 3 Award BIOS Setup 3 2 4 INTEGRATED PERIPHERALS This section page includes all the items of IDE hard drive and Programmed Input Output features See also Section Chipset Features Setup CMOS Setup Utility Copyright 1984 1998 Award Software Integrated Peripherals DE OnChip Primary PC En abled DE En abled OnChip Secondary PC IDE Primary Master PIO IDE Primary Slave PIO IDE Secondary Master PIO IDE Secondary Slave PIO IDE Primary Master UDMA IDE Primary Slave UDMA IDE Secondary Master UDMA IDE Secondary Slave UDMA USB Controller USB Keyboard Support Init Display First AC97 Audio AC97 Modem IDE HDD Block Mode Power On Function xKB Power On Password xHot Key Power On Onboard FDC Controller Onboard Serial Port 1 Onboard Serial Port 2 UART Mode Select xUART Duplex Mode Onboard Parallel Port Parallel Port Mode ECP Mode Use DMA PWRON After PWR Fail Game Port Address Midi Port Address xMidi Port TRO CIR Port Address IRQ xC LR POLL A Au Au Auto En Di Au Au Bu E E DE 2F N Auto Aul uto to to Aut Menu Level gt If your IDE hard drive supports block mode select Enabled for automatic detection of the optimal number of abled block read write per
8. 01AA Bus Frequency 66MHz 100MHz 5 PCI slots on board compliant with version 2 2 PCI Local Bus spec One Optional ISA slot One AMR Audio Modem Riser slot on board Dual Master IDE connectors supporting UDMA33 66 for 4 IDE devices such as high capacity HDD CD ROM LS 120 and tape backup etc Two USB connectors in stack supporting up to 127 USB devices PS 2 Keyboad and PS 2 Mouse connectors One Infrared IrDA TX DX connector One FDD port supporting two Floppy drives of 1 2MB 1 44MB 2 88MB One parallel port for SSP EPP ECP mode printer Two 16550A Fast UART compatible connectors for serial and VGA port One Game Midi port and 3 Audio Jacks for Speak out Line in and Microphone in One SB Link Connector for Sound Card and PCI connection ATC6430M Mainboard BIOS Support Built in VGA BIOS in Intel 810 and built in Keyboard BIOS AWARD BIOS in Intel 810 providing CMOS Setup Utilities Standard CMOS Features Setup for Date Drives and VGA Advanced BIOS Features Setup for CPU Cache Self Test Boot Device Typematic Rate and Security Options etc Advanced Chipset Features Setup for SDRAM CAS RAS System BIOS Cacheable and Video BIOS Cacheable etc Integrated Peripherals Setup for IDE Mode USB Audio and Modem etc Power Management Setup on Video HDD CPU etc PnP PCI Configurations Setup for PnP Reset Resources etc PC Health Status Control and Setup Freque
9. Award BIOS Setup CHAPTER 3 AWARD BIOS SETUP Award BIOS manufacturer provides access to the system BIOS through the hardware and software on mainboard The hardware consists of a Flash ROM 4MB in 6430M mainboard and the software is a group of programs that are installed in the ROMBIOS along with all the other data that should be included into the BIOS After the BIOS is updated if you want to clear the old setup data stored in the CMOS then you can reset CMOS as follow NOTE Incase CMOS should be reset firstunplug the power cord then set Jumper 8 2 3 closed for at least 5 seconds reset JP8 1 2 closed so as to return to normal position and plug the power cord again E de Reset CMOS 123 JPS i PCI 1 Slot Chapter 3_Award BIOS Setup ATC6430M Mainboard 3 1 UPDATE BIOS PROCEDURE 3 1 1 BIOS Update If the BIOS needs to be updated you can get a CD with the updated BIOS utility in the package The CD includes awdflash exe BIOS update utility program awdflash doc The update procedure is as following 1 Boot the system to DOS mode in a normal manner 2 Insert the updated CD to drive D or E 3 Change working directory to CD ROM drive D or E which contains the update BIOS CD Type dx or e V then press ENTER 4 Type cd flash then press ENTER 5 Type awdflash then press ENTER for running the BIOS update utility 6 Type update BIOS file
10. EY Decrease the numeric value or make changes F1 KEY Help General help F5 KEY Old Value Restore the pervious CMOS value from CMOS F6 KEY Load Fail Safe Load the fail safe default CMOS value from Defaults BIOS default table F7 KEY Load Optimized Load the optimized default Defaults F10 KEY Save amp Exit Save all the CMOS changes and Exit setup Setup only for Main Menu Chapter 3_Award BIOS Setup ATC6430M Mainboard 3 2 1 STANDARD CMOS FEATURES This screen records some basic hardware information and sets the system clock and error handling These records can be lost or corrupted if the on board battery has failed or is weak CMOS Setup Utility Copyright 1984 1998 Award Software Standard CMOS Features Date Mon Apr 26 1999 Item Help Time Lost 9s 20 IDE Primary Master Press Enter None gt IDE Primary Slave Press Enter None IDE Secondary Master Press Enter None IDE Secondary Slave Press Enter None Menu Level Change the day month year and century Drive A 1 44M 3 5in Drive B None Floppy 3 mode support Disabled Video EGA VGA Halt On All Errors Based Memory 640K Extended Memory 64512K Total Memory 65536K Tle Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail safe defaults F7 O ptimized Defaults Date Allows user to change the day month year and century with Y2K support The day from Sun to Sat automatically changes when
11. HLP file Chapter 3_Award BIOS Setup ATC6430M Mainboard 3 2 SYSTEM BIOS CONFIGURATION SETUP The following pages explain how to set up the BIOS configuration under the Award BIOS The SETUP program is stored in the Read Only Memory ROM on the mainboard To do the SETUP procedure press the lt Del gt key when the system is booting up The following main menu will appear Please select STANDARD CMOS FEATURE to enter the next screen CMOS Setup Utility Copyright C 1984 1998 Standard CMOS Feature Frequency Voltage Control Advanced BIOS Feature Load Fail Safe Defaults Advanced Chipset Feature Load Optimized Defaults Integrated Peripherals Set Supervisor Password Power Management Setup Set User Password PnP PCI Configurations Save amp Exit Setup PC Health Status Exit Without Saving Esc Quit TIC gt Select Item F10 Save amp Exit Setup Time Date Hard Disk Type The section at the bottom of the main menu explains how to control this screen The upper section displays the items highlighted in the list 16 ATC6430M Mainboard Chapter 3 Award BIOS Setup Control Key Description UP ARROW Move to the previous item DOWN ARROW Move to the next item LEFT ARROW Move to the item on the left RIGHT ARROW Move to the item on the right Esc KEY Esc Main Menu Quit without saving changes Setup menu Exit current page and return to main menu PgUp KEY Increase the numeric value or make changes PgDn K
12. Host Bus Intel PPGA Celeron CPUs To enhance its peripheral support 5 PCI slots are mounted on board with an optional ISA slot to meet some exceptional users requirements In addition to the incorporated VGA in Intel 810 its wide and inclusive add on features are described one by one in later part of this chapter Before that let us see some architectural features of Intel 810 Chipset Combination FW82810D C 100 FW82810E FW82801AA With 4MB Display cache Yes Supporting UDMA 66 Yes Shared Memory After 7M installing VGA driver Users should check with your dealer for the right chipset type on your mainboard Chapter 1 System Features ATC 6430M Mainboard 1 2 System Specifications of 6430M Mainboard oO 0 CPU Support Single CPU with both Slot 1 and PPGA Socket 370 on board for choice Supports CPU Clock 66MHz 100MHz and 133MHz 133MHz support Slot 1 socket only CPU Clock Ratios from 3 0x to 8 0x step 0 5x Supports CPUs Pentium II 233MHz 450MHz Celeron 300MHz 500MHz and Pentium II 450MHz 650MHz CPU Core Voltage 1 30V 2 05V step 0 05V and 2 1V 3 5V Step 0 1V CPU I O Voltage 3 3V Built in Switching Voltage Regulator supporting Vcore autodetection Memory Support Two DIMM sockets on board supporting up to 512MB SDRAM PC 66 PC 100 compatible T O System On board Intel 810 Chipset for I O Control FW82810DC100 FW82810E FW828
13. How To Use This Manual ATC6430M Mainboard HOW TO USE THIS MANUAL This manual is written in a user friendly style It would be advisable for users to read it in an orderly sequence 1 For Hardware Information Read COMPONENT LOCATION DIAGRAM Page A QUICK JUMPER amp CONNECTOR SETTING Page B Slot 1 and CPU Installation Page C CONNECTORS AND JUMPERS DESCRIPTION and Page D List of Packaging 2 For Mainboard and System Features Read Chapter 1 System Features and you will find helpful information on mainboard and system features Especially when you want to do some feature setup detailed instructions are provided therein to help you through 3 For CPU Memory and Drivers Installation Read Chapter 2 Installation for your CPU memory and application drivers installation Detailed instructions are provided to guide all kinds of users 4 For BIOS Update and Setup Read Chapter 3 Award BIOS Setup for updating your mainboard BIOS and setting up your BIOS Configuration 5 For other Technical Support Read APPENDIX A fill and send the Request Form to your dealer for other technical support The default settings on a mainboard is not necessarily what user expects A user friendly manual would be the handiest assistant to help change the on board configuration or default setting In case this manual cannot solve all your problems please ask your dealer for help and be sure the warranty on your system is st
14. IRQ A D Disab Tl lt Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail safe defaults F7 Optimized Defaults ACPI function This item is to set the ACPI Advanced Configuration Power Interface function enabled or disabled Power Management This category allows you to select the type or degree of power saving and is directly related to the following modes Suspend HDD Power Down Min Power Minimum power management Doze lhr Standby l1hr Saving Suspend 1hr HDD Power Down 15min Max Power Maximum power management Doze 1min Standby 1min Saving Suspend 1min HDD Power Down 1min User Allows you to set each mode individually When not disabled each Define of the ranges are from Imin to lhr except for HDD Power Down which ranges from 1 to 15min and disable 30 ATC6430M Mainboard Chapter 3 Award BIOS Setup Video Off Method This determines the manner in which the monitor is blanked VIH SYNC This selection will cause the system to turn off the vertical and Blank horizontal sync ports and write blanks to the video buffer Blank Screen This option only writes blanks to the video buffer DPMS Initial of Display Power Management Signaling Video off In Suspend This determines the manner in which the monitor is blanked Suspend Type Select the suspend type Only CPU enters sleeping mode Full on Sus
15. RQ3 4 5 7 9 1011 12 14 15 DMA0 1 3 5 6 7 Assign to This item allows you to determine the IRQ DMA assigned to the ISA bus and is not available to any PCI slot Choices are Legacy ISA and PCI ISA PnP Memory Resources Memory Resources has two events Resources Memory Base N A 32 ATC6430M Mainboard Chapter 3 Award BIOS Setup Memory Resources Length 8K 33 Chapter 3_Award BIOS Setup ATC6430M Mainboard PCI VGA Snoop It determines whether the MPEG ISA VGA cards can work with PCI VGA or not Enabled When PCI VGA working with MPEG ISA VGA Card Disabled When PCI VGA not working with MPEG ISA VGA Card 34 ATC6430M Mainboard Chapter 3 Award BIOS Setup 3 2 7 PC Health Status This screen shows your in use PC Health Condition CMOS Setup Utility Copyright 1984 1998 Award Software PC Health Status Item Help Vcore 2 5 OW So SV PSV 1 2W 12W Pll BV WIL CW VOltage Battery CRU WemjoSie sic wieS System Temperature CPU Fan Speed Chassis Fan Speed CPU Warning Temperature 70 C 158 F Shutdown Temperature 90 C 194 F Menu Level Tl lt Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail safe defaults F7 Optimized Defaults Vcore Chassis Fan Speed These items are to show the in use PC conditions CPU Warning Temperature Default temperature is 70 C 158 F Shutdown Temperature Default temperature is 90 C 194 F 35 Chapt
16. The system boot will not stop for a floppy drive or keyboard error It Disk Key will stop for all other errors Memory To display what is detected by POST Power On Self Test of the BIOS Base Memory The POST will determine the amount of base or conventional memory installed in the system The value of the base memory is typically 512K or 640K based on the memory installed on the motherboard Extended Memory How much extended memory is present during the POST This is the amount of memory located above 1MB in the CPU s memory address map Total Memory Displays the total memory available in the system 20 ATC6430M Mainboard Chapter 3 Award BIOS Setup 3 2 2 ADVANCED BIOS FEATURES This screen is a list of system configuration options Some of them are defaults required by the mainboard s design others depend on the features of your system CMOS Setup Utility Copyright 1984 1998 Award Software Advanced BIOS Features Virus Warning Disabled CPU L1 Cache Enabled CPU L2 Cache Enabled CPU L2 Cache ECC Checking Enabled gt xProcessor Number Featur N A Menu Level Quick Power On Self Test Enabled Allows you to choose the First Boot device Floppy VIRUS warning feature Second Boot device HDD 0 for IDE Harci Disk Door Third Boot device SCSI sector protection If Boot other device Enabled this function is enabled Swap Floppy Drive Disabled and someone attempt to Boot Up Floppy See
17. VGA Driver nstallationi sr ab tea cance Sivek 12 2 6 Sound Driver Installation asia 12 CHAPTER 3 Award BIOS Setup vvrrrrrrrrrrerrrce rese nesesrenenecenee 13 3elWpdateBIOS Procedarte stare A 14 3 2 System BIOS Configuration Setup ceeeeeeeeeees 16 3 2 1 Standard CMOS Features iii ie 18 3 2 2 Advanced BIOS Features tists 2eeditaderr i dates einai 21 3 2 3 Advanced Chipset Features 2 inveaseniien dan denies 24 3 2 4 IMegratedPeriphetals i Lirailiaira eriadan 26 Contents ATC6430 Mainboard 3 2 5 Power Management Seip acri 27 3 2 6 PNP PCE Configurations iniii oee gna arl 31 3 2 7 PE Health Stasi a aaea S e EEEa aS 33 3 2 8 Frequency Voltage Control sssssesesseeesseesseessessseeesssersseessersseessseeessees 34 3 2 9Load Fail Safe Define iaia za 35 3 2 10 Load Optimized Defablts cuile i re A Wed na 35 3 2 11SupervisorPassword User Password iii 35 3 2 12 Sa4VE amp XIE SEUD o nerse E aaa 35 3 2 13Exit without Avis nea e eesi ili 35 Appendix A Technical Support Request Form ATC6430M Mainboard Chapter 1 System Features CHAPTER 1 System Features 1 1 Introduction 6430M mainboard is designed to run with Intel 810 chipset to enhance the performance and extraordinary value of the Intel Celeron processor powered PC On the other hand it is mounted with both Slot 1 and Socket 370 connector for users to make their CPU choice It supports 66MHz 100MHz and 133MHz
18. ainboard 2 4 INTEL 810 DRIVER INSTALLATION gt INF Files for Windows 95 98 1 Start Windows 95 98 2 Put the All In One CD into your CD ROM drive 3 Choose Intel 810 820 Inf Files on the Autorun main menu 4 Then follow the instruction on the screen INF Files that enable the Intel 810 820 Chipsets to be recognized by listed operating systems 2 5 VGA DRIVER INSTALLATION Install Intel 810 AGP Driver For Win95 98 NT 1 Start Windows 95 98 NT 2 Put the All In One CD into your CD ROM drive 3 Choose Intel 810 AGP Driver on the Autorun main menu 4 Press Next to install the driver 5 Follow the instructions on the screen to complete the installation 2 6 SOUND DRIVER INSTALLATION Install Sound Driver For Win95 98 NT 1 Start Windows 95 98 NT 2 Put the All In One CD into your CD ROM drive 3 Choose Audio Device Driver on the Autorun main menu 4 Follow the instructions on the screen to finish the installation Please refer to readme doc file to get more detailed information Install YAMAHA Software Synthesizer For Win95 98 NT 1 Start Windows 95 98 NT 2 Put the All In One CD into your CD ROM drive 3 Choose YAMAHA Software Synthesizer on the Autorun main menu 4 Follow the instructions on the screen to finish the installation Please refer to readme doc file to get more detailed information Note the sound driver is not supported under DOS operating system 12 ATC6430M Mainboard Chapter 3
19. er 3_Award BIOS Setup ATC6430M Mainboard 3 2 8 FREQUENCY VOLTAGE CONTROL This screen controls the green features of this mainboard CMOS Setup Utility Copyright 1984 1998 Award Software Frequency Voltage Control Auto Detect DIMM PCI CLK Disabled Item Help CPU SDRAM PCI Clock amp SSC Default CPU Ratio xX 3 Menu Level Tl lt Move Enter Select PU PD Value F10 Save ESC Exit Fl General Help F5 Previous Values F6 Fail safe defaults F7 Optimized Defaults Auto Detect DIMM PCI CIK If this item is enabled the unused DIMM and PCI slot clock will be disabled If this item is disabled the unused DIMM and PCI slot will still get the active clock signal CPU SDRAM PCI Clock amp SSC Use this item to set CPU base clock frequency and Spread Spectrum clocking function The optimized range of combinations are CPU SDRAM PCI SSC 66 155MHz 100 155MHz 33 38MHz On Off After you change the CPU Clock Frequency and the system can not start please do the following procedures 1 Turn the system off firstly 2 Turn on the system Then press and hold the Insert key at boot 3 Select the proper figure in the item of CPU SDRAM PCI Clock Save and Exit Setup CPU Ratio Use this item to set CPU ratio which includes x 3 x 3 5 x 4 x 4 5 x 5Ox 5 5 x 6 x 6 5 x 7 x 7 5 and x 8 36 ATC6430M Mainboard Chapter 3 Award BIOS Setup 3 2 9 LOAD FAIL SAFE DEFAULTS When your mainboard has
20. he BIOS to be updated as needed Mainboards that contain a BIOS with the Intel defined BIOS update API can be quickly and easily updated if required without obtaining a complete BIOS upgrade Using this utility integrators can easily verify that the correct stepping data is present in all mainboards However if the stepping data requires to be updated the mainboard BIOS must contain the Intel defined BIOS update API otherwise a complete BIOS upgrade is required from the mainboard vendor Since API program can only be executed under DOS Real Mode you must enter Real Mode first and load the API program to Drive C To load the program to C by following steps 1 Type md c api and press Enter Directory api is made in Drive C now 2 Insert the Driver Utility CD into CD ROM Drive E 3 Then type copy e api c api and press Enter API program is loaded to Drive C now 4 Type CA api checkup to execute this program The main menu should now be displayed with the following four options 1 Check and load update 2 Specify stepping data file current pep pdb 3 Help 4 Quit without loading update Select 1 to know the stepping filename select 2 to load right patch code then select 1 to update proper patch code Now the screen will show the message please remove the CD from CD ROM drive Then cold boot mechanical power off system to continue For more information please refer to CHECKUP
21. her is with PME signal supporting And you can set PCI PME 7 Chapter 1 System Features ATC 6430M Mainboard Function enabled through Power Management Setup from the BIOS setup screen Caution For Wake On LAN the 5V standby line for the power supply should be capable of delivering 5V 5 at 720mA Failure to provide adequate standby current when implementing Wake On LAN will damage the power supply CA WOLconnector 6430M Mainboard Chapter 2 Installation CHAPTER 2 INSTALLATION 2 1 INSTALLATION PROCEDURE Before installing the computer please prepare all components such as CPU DRAM peripherals such as hard drive keyboard CD ROM and accessories such as cables Then install the system as following Put CPU heat sink refer to Celeron CPU installation guide or see the following setup chapter and DRAM modules on the mainboard Plug add on cards into PCI slots if needed Connect cables to peripheral devices especially for COM2 connector Make sure all components and devices are well connected turn on the power and setup System BIOS based on your configuration Install peripheral devices add on card drivers and test them If all of above procedures are running successfully turn the power off and screw the chassis cover to the chassis Chapter 2 Installation 6430M Mainboard 2 2 CPU INSTALLATION This mainboard supports PPGA Socket 370 and Slot 1 processors The 6430M mainboard has built in S
22. ill valid REMARK Intel is a registered trademark of Intel Corporation All other brands and product names are registered trademarks of their respective companies ATC6430M Mainboard Contents CONTENTS QUICK JUMPER amp CONNECTOR SETTING orcrerrererere A SLOT 1 AND PENTIUM INVII INSTALLATION 00 B CONNECTORS AND JUMPERS DESCRIPTION C CHECKLIST OF PACKAGING cccsscscsssccssscsccsscsscesesees D HOW TO USE THIS MANUAL TABLE OF CONTENTS CHAPTER 1 System Features ccccsccssssscssssccssssscssssces ces 1 BTU CON asi ccs ais ia BOGE IEE Re 1 1 2 System Specifications 23 suas aula 2 l 3 Features Hishlieht cioe di e 3 1 3 1 Add on Features for VGA in Intel 810 4 1 3 2 Add on Features for AUdi0 i 4 1 3 3 AMR and AC 97 CODEC Controller 5 1 3 4 Software Power Off Control 5 1 3 5 Modem Ring Ollio aan alias 6 1 3 6 SB Link Sideband Signal 6 1 3 7 Ultra DMA 66 Cable Optional 7 1 3 8 W ake On lA WN oiicicsscassdvcdacmasessadoasseveestwusdogsesnveevannwonsesaraverstees 8 CHAPTER 2 Installation 9 2 1 Installation PFOCEdUre s srt rara perire 9 22 CPU Insfallatoni sre tono 10 2 3 System Memory Installation rash era dda essrresssesse 11 2 4 Intel 810 Driver Installation 2 12 2 5
23. irst This item allows you to decide to activate PCI VGA or on chip VGA first The choice PCI Slot Onboard AC97 Audio AC 97 Modem This item allows you to decide to enable disable the 1810 chipset family to support AC97 Audio Modem IDE HDD Block Mode This allows your HD controller to use the fast block mode to transfer data to and from your HD drive Enabled IDE controller uses block mode Disabled IDE controller uses standard mode Power On Function This function supports 7 Power On modes Password Hot Key Mouse Move Mouse Click Any Key Button Only and Keyboard 98 Default is Button Only If Password is chosen the item KB Power On Password will appear to ask you to enter password If Hot Key is chosen the item Hot Key Power On will appear to ask you to pick the Hot Key On Board FDC Controller This item will enable or disable the floppy disk controller On Board Serial Port 1 User can select serial port IRQ If set to Auto system will assign an IRQ for it Note set to Auto is not recommended On Board Serial Port 2 User can select serial port IRQ If set to Auto system will assign an IRQ for it Note set to Auto is not recommended 28 ATC6430M Mainboard Chapter 3 Award BIOS Setup UART Mode Select This lets you select the Infrared mode Choices are IrDA ASKIR Normal and SCR Only when you choose IDA or ASKIR the screen will then show UART2 Duplex Mode for you to choose
24. k Enabled werte data into CALS Boot Up NumLock Status On area BIOS will show a Gate A20 Option Fast warning message on Typematic Rate Setting Disabled screen and alarm beep xTypematic Rate Chars Sec xTypematic Delay Msec 250 Security Option Setup OS Select For DRAM gt 64MB Non OS2 HDD S M A R T Capability Disabled Report No FDD for Win 95 No Tl lt Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail safe defaults F7 Optimized Defaults Virus Warning Allows user to choose the VIRUS warning feature for IDE Hard Disk boot sector protection If this function is enabled and someone attempts to write data into this area BIOS will show a warning message on screen and alarm beep WARNING Disk boot sector is to be modified Type Y to accept write or N to abort write Award Software Inc CPU LI Cache L2 Cache These two categories speed up memory access However it depends on CPU design The default value is Enabled 21 Chapter 3_Award BIOS Setup ATC6430M Mainboard CPU L2 Cache ECC Checking If Enabled this function will do ECC check to CPU L2 Cache automatically Quick Power On Self Test This category speeds up Power On Self Test while booting If Enabled BIOS will skip some items under check by POST First Boot Device Second Boot Device Third Boot Device Boot Other Device Allows user to select the
25. l Port 31 Chapter 3_Award BIOS Setup ATC6430M Mainboard 3 2 6 PNP PCILCONFIGURATION This screen configures the PCI Bus slots CMOS Setup Utility Copyright 1984 1998 Award Software PnP PCI Configurations PNP OS Installed No Item Help Reset Configuration Data Disabled Menu Laval gt Resources Controlled By Auto IRQ Resources Press Enter DMA Resources Press Enter Memory Resources Press Enter Select Yes if you are usingaPlugandPlayOs Select NOif youneedthe BIOS to confirm non boot device PCI VGA Palette Snoop Disabled Tl lt Move Enter Select PU PD Value F10 Save ESC Exit Fl General Help F5 Previous Values F6 Fail safe defaults F7 Optimized Defaults PNP OS Installed Select Yes if you are using a Plug nad Play OS Select No if you need the BIOS to confirm non boot device Reset Configuration Data This item allows you to determine whether to reset the configuration data or not Resource Controlled by The Award Plug and Play BIOS has the capability to automatically configure all of the boot and Plug amp Play compatible devices However this capability means absolutely nothing unless you are using a Plug and Play OS such as Windows 95 Choices are Auto and Manual IRQ Resources DMA Resources When resources are controlled manually assign each system interrupt DMA channel a type depending on the type of device using the interrupt DMA channel I
26. name with version number bin ENTER 7 If you do not want to save the old BIOS type N when the screen displays the message Do you want to save BIOS Y N 8 Type Y when the screen shows the message Are you sure to program Y N 9 Follow instructions displayed on the screen DO NOT remove the update BIOS CD from the CD ROM drive nor turn the system power off until the BIOS update is completed 10 Turn the power off Clear the data in CMOS according to the procedure described in the previous page 11 Turn the system power on and test that your system is working properly 14 ATC6430M Mainboard Chapter 3 Award BIOS Setup 3 1 2 UPDATE MICROCODE API Intel also provides MICROCODE API Applications Programming Interface for mainboard user to update data block in BIOS quickly and easily You can find this utility in the All In One CD in the mainboard package The BIOS code on the mainboards contains data that is specific to each silicon stepping of the processor Integrators must ensure that this BIOS stepping data matches the used processor stepping When the BIOS does not contain stepping data that matches the processor stepping integrators must update the data in the BIOS before shipping the system Historically the systems have been updated by replacing the entire BIOS with a new revision of BIOS that contains the correct stepping data Intel s BIOS update API allows just the stepping data within t
27. ncy Voltage Control on CPU SDRAM PCI amp SSC etc Load Fail Safe Defaults Load Optimized Defaults Chapter 1 System Features Set Supervisor User Password Board Dimension 308mm x 202mm in ATX form Factor with one ATX Power Connector Chapter 1 System Features ATC 6430M Mainboard 1 3 Features Highlight 1 3 1 Add on Features for VGA in Intel 810 no ui Integrated Graphics Controller 3D Hyper Pipelined Architecture Full 2D H W Acceleration e Motion Video Acceleration 3D Graphics Visual Enhancements Flat amp Gouraud Shading Mip Maps with Bilinear and Anisotropic Filtering Fogging Atmospheric Effects Z Buffering 3D Pipe 2D Clipping Backface Culling gt 3D Graphics Texturing Enhancements Per Pixel Perspective Correction Texture Mapping Texture Compositing Texture Color Keying Chroma Keying Integrated 24 bit 230MHz RAMDAC 2D Graphics e Upto 1600 x 1200 in 8 bit Color at 85 Hz Refresh e Hardware Accelerated Functions H W Motion Compensation Assistance for SSW MPEG2 Decode Software DVD at 30fps H W Overlay Engine with Bilinear Filtering 1 3 2 Add on Features for Audio n Intel 810 ICH with built in AC 97 controller Supporting HRTF based 3D positional audio A3D Q3D wavetable and 3D surround sound No
28. nfirm the new password by typing it again and press lt Enter gt Disable password Press the lt Enter gt key instead of entering a new password when the Enter Password dialog box appears A message will appear for confirming that the password is disabled CAUTION If you forget your password you must clear CMOS first and restart system so as to set up password again See Reset CMOS on Page 12 3 2 12 SAVE amp EXIT SETUP This allows you to save the new setting values in the CMOS memory and continue with the booting process If you select this item and press Y then these records will be saved in the CMOS memory on the mainboard It will be checked every time you turn your computer on 3 2 13 EXIT WITHOUT SAVING This allows you to exit the BIOS setup utility without recording any new values or changing old ones 37
29. pend Both CPU and chipset enter sleeping mode MODEM Use IRQ This item determines the IRQ in which the MODEM can be used The choice 3 4 5 7 9 10 11 NA Suspend Mode When enabled and after the set time of system inactivity all devices except the CPU will be shut off HDD PowerDown When enabled and after the set time of system inactivity the hard disk drive will be powered down while all other devices remain active Soft Off by PWR BTTN Instant off When push the power button the system power will be off immediately Delay 4 sec when push the power button it will enter suspend mode We need to push the power button and hold it for 4 seconds to turn off the power PCI PME Function With PCI card supporting PCI Power Management capability and this item setting to Enabled the system can be waked up by PCI card PowerOn by Ring Enabled when system is in suspend mode it can be waked up by modem Disabled it cannot be waked up by modem Resume by Alarm When Enabled two additional lines will be added to the screen Date of Month Alarm Time hh mm ss Alarm to let user set the desired date and time After power off the system will automatically power on at the specified date and time Reload Global Timer Events When enabled an event occurring on each device listed below restarts the global time for Standby mode IRQ 3 7 9 15 NMI Primary IDE 0 Primary IDE 1 Secondary IDEO Secondary IDE1 Floppy Disk Serial Port Paralle
30. problems and needs to trouble shoot the system you can use this function The default values loaded only affect the BIOS Features Setup Chipset Features Setup Power Management Setup and PNP PCI Configuration Setup There is no effect on the Standard CMOS Setup To use this function select it from main menu and press lt Enter gt A line will appear on the screen asking if you want to load the fail safe default values Press lt Yes gt and lt Enter gt then the BIOS default values will be loaded 3 2 10 LOAD OPTIMIZED DEFAULTS This allows you to load optimal settings which are stored in the BIOS ROM The default values loaded only affect the BIOS Features Setup Chipset Features Setup Power Management Setup and PNP PCI Configuration Setup There is no effect on the Standard CMOS Setup To use this function select it from main menu and press lt Enter gt A line will appear on the screen asking if you want to load the optimized default values Press lt Yes gt and lt Enter gt then the Setup default values will be loaded 3 2 11 SUPERVISOR PASSWORD USER PASSWORD This allows you to set the password The mainboard defaults with password disabled If you set both supervisor and user passwords only the supervisor password allows you to enter the BIOS SETUP program Enter Change password Enter the current password And at the prompt key in your new password up to eight alphanumeric characters then press lt Enter gt At the next prompt co
31. r number of cylinders number of read write heads Landing Zone number of sectors per track Capacity Displays your disk drive size Access Mode Choose the access mode for the hard disk The choices Normal LBA Large Auto 19 Chapter 3_Award BIOS Setup ATC6430M Mainboard Drive A Drive B This category identifies the types of floppy disk drive A or drive B that have been installed in the computer No floppy drive installed Floppy 3 Mode Support This is the Japanese standard floppy drive This standard stores 1 2MB in a 3 5 diskette Video To selects the type of primary video adapter used for the system monitor EGA VGA Enhanced Graphics Adapter Video Graphics Array For EGA VGA SEGA SVGA or PGA monitor adapters CGA 40 Color Graphics Adapters power up in 40 column mode CGA 80 Color Graphics Adapters power up in 80 column mode MONO Monochrome adapter includes high resolution monochrome adapters Halt On This category determines whether the computer will stop if an error is detected during power up The system boot will not be stopped for any error that may be detected All errors When the BIOS detects a non fatal error the system will be stopped and you will be prompted All But The system boot will not stop for a keyboard error It will stop for all Keyboard other errors All But The system boot will not stop for a floppy drive error It will stop for all Diskette other errors All But
32. sabled sector the drive can PCI Slot support to to Enabled tton Only MESI item rae E Enabled 8 IRQ4 8 IRQ3 ormal Aut Hanka 378 I RQ7 ECP 3 O ff 201 Disabled 7 Disabled iil Tl lt Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail safe defaults F7 Optimized Defaults On Chip Primary PCI IDE On Chip Secondary PCIIDE This setup item allows you to either enable or disable the primary secondary controller You might choose to disable the controller if you want to add higher performance or specialized controller IDE Primary Master Slave PIO IDE Secondary Master Slave PIO PIO Programmed Input Output it allows the BIOS to tell the controller what it wants and then let the controller and the CPU to complete the task by themselves This is 27 Chapter 3_Award BIOS Setup ATC6430M Mainboard simpler and faster Your system supports five modes 0 4 which primarily differ in timing When Auto is selected the BIOS will select the best available mode IDE Primary Master Slave UDMA IDE Secondary Master Slave UDMA Auto will support the Ultra DMA function Disabled will not support the Ultra DMA function USB Controller This item allows you to decide to enable disable the USB controller USB Keyboard Support Enabled will support USB keyboard in Win95 2 1 and NT 5 0 or above operating system Init Display F
33. te If you want to enable the onboard AC 97 CODEC you need to set JP9 pin 2 3 closed But in this way the AMR slot will only accept ariser board with Modem CODEC and cannot accept another Audio Riser ATC6430M Mainboard Chapter 1 System Features 1 3 3 AMR and AC 97 CODEC Controller AMR slot and AC 97 CODEC are integrated into he Mainboard to enable audio and modem playback AMR Audio Modem Riser slot is mounted on board to connect riser board with Audio and or Modem CODEC AMC AC MC Adapters The AMR specification developed by Intel provides a mechanism for AC 97 codes to be on a riser card To enable the onboard AC 97 CODEC set JP9 pin 2 3 closed And in such way you can further plug a riser board with Modem CODEC to the AMR slot Otherwise disabling onboard AC 97 CODEC by setting JP9 2 closed you can plug a riser board with Audio Modem CODEC to the AMR slot See Page A for AMR location on 6430M Mainboard 1 3 4 Software Power Off Control This mainboard supports Software Power Off Control feature through the SMM code in the BIOS under Windows 95 98 and MS DOS operation system environment First you should connect the power switch cable to the connector PS ON on the mainboard In the BIOS screen of POWER MANAGEMENT SETUP choose User Define or Min Power Saving or Max Power Saving in Power Management In Windows 95 98 if you want to power off the system you just need to choose
34. witching Voltage Regulator to support CPU Vcore autodetection That is It is smart enough to detect and recognize the CPU voltage clock ratio and enables users to set up the CPU frequency from the BIOS Setup Screen Users can adjust the frequency through Frequency Voltage Control of the BIOS Setup Screen A How to install CPUs for Socket 370 1 Insert CPU Pin 1 to Pin 1 corner 2 Insert Slot 1 Terminator Kit of Socket 370 and lock it to Slot 1 CPU for Socket 370 Pin 1108 Corner gt n O Terminator Kit Lever Socket 370 B How to install CPU for Slot 1 For Slot 1 CPU installation please refer to Page B Slot 1 installation of this manual 10 6430M Mainboard Chapter 2 Installation 2 3 SYSTEM MEMORY INSTALLATION 6430M mainboard provides two 3 3V 168 pin DIMM sockets for system memory expansion from 8MB to 512MB SDRAM These two DIMMSs are arranged to two banks please refer to page A Bank DIMM PC 100 Memory Module Total Memory Bank0 DIMM1 8 16 32 64 128 256MB 8MB 256MB Bank1 DIMM2 8 16 32 64 128 256MB 8MB 256MB Total System Memory 8MB 512MB DIMM type Size parity supported 2 PC 66 100 or higher performance memory module Both parity or non parity are available 2 3 3V single double side S 8 16 32 64 128 256Mbytes For either 66MHz 100MHzand 133MHzhost bus CPUs please use 10ns or faster and PC 100 compliant modules Chapter 2 Installation 6430M M
35. writes to this memory area a system error may result Memory Hole At 15M 16M Certain space in memory can be reserved for ICH ICHO Delay Transaction This chipset has an embedded 32 bit posted write buffer to support delay transactions cycles Select Enabled to support compliance with PCI specification version 2 1 The choice Enabled disabled space On chip Video Window Size Determine the size of memory space that can be allocated for on chip graphics device The following items are optional for onboard display cache setting CAS Latency The number of clock cycles of CAS latency depends on the Display Cache timing The choices 2 3 2 gives faster performance and 3 gives more stable performance Paging Mode Control Close the GMCH will precharge all during the service of a 25 Chapter 3_Award BIOS Setup ATC6430M Mainboard page miss Open it will precharge bank during the service of a page miss RAS to CAS Override By CAS LT the RAS to CAS delay timing will be the same as item of CAS Latency Override the value will be fixed in 2 RAS Timing This item controls the active time of RAS and bank cycle time Fast gives faster performance and Slow gives more stable performance RAS Precharge Timing If an insufficient number of cycles is allowed for the RAS to accumulate its charge before DRAM refresh the refresh may be incomplete and the DRAM may fail to retain data Fast gives faster performance
36. you set the date The date from 1 to 31 ear The month Jan through Dec The year from 1900 to 2099 Time The time format is lt hour gt lt minute gt lt second gt allowing user to set the internal clock 18 ATC6430M Mainboard Chapter 3 Award BIOS Setup IDE Primary Master Primary Slave Secondary Master Secondary Slave Press Enter to enter next page for detailed hard drive settings CMOS Setup Utility Copyright 1984 1998 Award Software IDE Primary Master Detection Press Enter Menu Level gt gt IDE Primary Master Auto Capacity 2557 MB Access Mode Auto Cylinder 4956 rO Aro Cereser Cie FIDI Save nes lt on this channel Head 16 Precomp 0 Landing Zone 4955 Sector 63 Tle Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail safe defaults F7 Optimized Defaults IDE HDD Auto Detection Press Enter to auto detect the HDD If detection is successful it fills the remaining fields on this menu IDE Primary Master If you select Auto the BIOS will detect the HDD amp CD ROM Drive automatically at the POST stage and show the IDE for HDD amp CD ROM Drive If you select manual please contact your hard disk vendor or dealer to get the information listed below Then enter the figure directly and press lt Enter gt The following options are selectable only if the IDE Primary Master item is set to Manual Cylinde

Intel ATC6430M User's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents